aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAge
* [POWERPC] Generalize tsi108 PHY typesJosh Boyer2007-05-07
| | | | | | | | | | | | | Add a phy_type field to the tsi108 ethernet structures to indicate which PHY is used on a board. This is derived from the "compatible" property in the ethernet-phy node of the device tree. The default remains the MV88E PHY. Also, convert the setup code to use of_get_mac_address instead of hard coding a lookup for the "address" property in the ethernet node. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] via-pmu: remove LED sleep notifierJohannes Berg2007-05-07
| | | | | | | | | | | The generic LED code now makes sure that suspended devices don't blink, so we no longer need to do it ourselves. For the suspend to disk case, however, we need to make sure that we don't blink if the PMU sysdev was suspended before the LED device. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Don't shutdown TX on mpc5200 serial port if it is a consoleGrant Likely2007-05-07
| | | | | | | | | If the serial port gets shut down, then console output stalls. 9 out of 10 kernel hackers agree, this is a bad thing. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] macintosh: Use common modalias generation for macio_sysfsSylvain Munaut2007-05-07
| | | | | | | | There is now a common function to generate the modalias string, so use it. We just need to add the \n at the end. Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Rename device_is_compatible to of_device_is_compatibleStephen Rothwell2007-05-07
| | | | | | | | | | | for consistency with other Open Firmware interfaces (and Sparc). This is just a straight replacement. This leaves the compatibility define in place. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Rename get_property to of_get_property: driversStephen Rothwell2007-05-02
| | | | | | | | These are all the remaining instances of get_property. Simple rename of get_property to of_get_property. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] get_property returns constStephen Rothwell2007-05-02
| | | | | | | | This is the last place that needs changing since get_property was changed to return "const void *". Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] PS3: Interrupt routine fixups.Geoff Levand2007-05-02
| | | | | | | | Fixups for the ps3 interrupt routines to support all HV device in a generic way. Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] Use menuconfig objects II - MacintoshJan Engelhardt2007-05-02
| | | | | | | | | Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that the user can disable all the options in that menu at once instead of having to disable each option separately. Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] apm_emu: Use generic apm-emulationJohannes Berg2007-05-02
| | | | | | | | | This patch removes a huge amount of code that is now in common code in drivers/char/apm-emulation.c Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* [POWERPC] drivers/macintosh/mac_hid.c: Make code staticAdrian Bunk2007-05-02
| | | | | | | This patch makes some needlessly global code static. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
* libata: honour host controllers that want just one hostLinus Torvalds2007-04-30
| | | | | | | | | | | | | | | | | | | | The Marvell IDE interface on my machine would hit a BUG_ON() in lib/iomem.c because it was calling ata_pci_init_one() specifying just a single port on the host, but that would actually end up trying to initialize two ports, the second one with bogus information. This fixes "ata_pci_init_one()" so that it actually passes down the n_ports variable that it got from the low-level driver to the host allocation routine ("ata_host_alloc_pinfo()"), which results in the ATA layer actually having the correct port number information. And in order to make it all work, I also needed to fix a few places that had incorrectly hard-coded the fact that a host always had exactly two ports (both ata_pci_init_bmdma() and ata_request_legacy_irqs() would just always iterate over both ports). Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* power management: implement pm_ops.valid for everybodyJohannes Berg2007-04-30
| | | | | | | | | | | | | | | | | | | | | | Almost all users of pm_ops only support mem sleep, don't check in .valid and don't reject any others in .prepare so users can be confused if they check /sys/power/state, especially when new states are added (these would then result in s-t-r although they're supposed to be something different). This patch implements a generic pm_valid_only_mem function that is then exported for users and puts it to use in almost all existing pm_ops. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: David Brownell <david-b@pacbell.net> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: linux-pm@lists.linux-foundation.org Cc: Len Brown <lenb@kernel.org> Acked-by: Russell King <rmk@arm.linux.org.uk> Cc: Greg KH <greg@kroah.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'for-linus' of ↵Linus Torvalds2007-04-30
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (56 commits) ieee1394: remove garbage from Kconfig ieee1394: more help in Kconfig ieee1394: ohci1394: Fix mistake in printk message. ieee1394: ohci1394: remove unnecessary rcvPhyPkt bit flipping in LinkControl register ieee1394: ohci1394: fix cosmetic problem in error logging ieee1394: eth1394: send async streams at S100 on 1394b buses ieee1394: eth1394: fix error path in module_init ieee1394: eth1394: correct return codes in hard_start_xmit ieee1394: eth1394: hard_start_xmit is called in atomic context ieee1394: eth1394: some conditions are unlikely ieee1394: eth1394: clean up fragment_overlap ieee1394: eth1394: don't use alloc_etherdev ieee1394: eth1394: omit useless set_mac_address callback ieee1394: eth1394: CONFIG_INET is always defined ieee1394: eth1394: allow MTU bigger than 1500 ieee1394: unexport highlevel_host_reset ieee1394: eth1394: contain host reset ieee1394: eth1394: shorter error messages ieee1394: eth1394: correct a memset argument ieee1394: eth1394: refactor .probe and .update ...
| * ieee1394: remove garbage from KconfigStefan Richter2007-04-29
| | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: more help in KconfigStefan Richter2007-04-29
| | | | | | | | | | | | | | | | - s/Device Drivers/Controllers/ - clarify who needs pcilynx - don't recommend Y for raw1394; M is typically used Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: ohci1394: Fix mistake in printk message.Simon Arlott2007-04-29
| | | | | | | | | | | | | | | | Fix the "attempting to setting" message in ohci1394. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: ohci1394: remove unnecessary rcvPhyPkt bit flipping in LinkControl ↵Bernhard Kauer2007-04-29
| | | | | | | | | | | | | | | | | | | | register Remove the unneeded code that clears, sets and again clears the rcvPhyPkt bit in the ohci1394 LinkControl register in ohci_initialize(). Signed-off-by: Bernhard Kauer <kauer@os.inf.tu-dresden.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: ohci1394: fix cosmetic problem in error loggingStefan Richter2007-04-29
| | | | | | | | | | | | | | If posted write failed, an "Unhandled interrupt(s) 0x00000100" message was logged by mistake. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: send async streams at S100 on 1394b busesStefan Richter2007-04-29
| | | | | | | | | | | | | | eth1394 did not work on buses consisting of S100B...S400B hardware because it attempted to send GASP packets at S800. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: fix error path in module_initAkinobu Mita2007-04-29
| | | | | | | | | | | | | | | | | | | | This patch fixes some error handlings in eth1394: - check return value of kmem_cache_create() - cleanup resources if hpsb_register_protocol() fails Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (whitespace)
| * ieee1394: eth1394: correct return codes in hard_start_xmitStefan Richter2007-04-29
| | | | | | | | | | | | | | | | | | | | This patch actually doesn't change anything because there was always 0 == NETDEV_TX_OK returned before. TODO: Return NETDEV_TX_BUSY in error case and test in different error conditions. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: hard_start_xmit is called in atomic contextStefan Richter2007-04-29
| | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: some conditions are unlikelyStefan Richter2007-04-29
| | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: clean up fragment_overlapStefan Richter2007-04-29
| | | | | | | | | | | | | | | | offset > fi->offset + fi->len - 1 == !(offset < fi->offset + fi->len) offset + len - 1 < fi->offset == !(offset + len > fi->offset) !(A || B) == (!A && !B) Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: don't use alloc_etherdevStefan Richter2007-04-29
| | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: omit useless set_mac_address callbackStefan Richter2007-04-29
| | | | | | | | | | | | We can't reconfigure the MAC address, hence we don't need the callback. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: CONFIG_INET is always definedStefan Richter2007-04-29
| | | | | | | | | | | | because CONFIG_IEEE1394_ETH1394 depends on it. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: allow MTU bigger than 1500Stefan Richter2007-04-29
| | | | | | | | | | | | | | | | | | | | RFC 2734 says: "IP-capable nodes may operate with an MTU size larger than the default [1500 octets], but the means by which a larger MTU is configured are beyond the scope of this document." Allow users to set an MTU bigger than 1500. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: unexport highlevel_host_resetAdrian Bunk2007-04-29
| | | | | | | | | | | | | | highlevel_host_reset no longer has any modular users. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: contain host resetStefan Richter2007-04-29
| | | | | | | | | | | | | | | | | | | | Call only eth1394's own host reset handler from .tx_timeout, not the reset hooks of all other IEEE 1394 drivers. A minor drawback of this patch is that ether1394_host_reset by timeout is not serialized against ether1394_host_reset by bus reset. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: shorter error messagesStefan Richter2007-04-29
| | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: correct a memset argumentStefan Richter2007-04-29
| | | | | | | | | | | | The old argument calculated the correct value in a wrong way. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: refactor .probe and .updateStefan Richter2007-04-29
| | | | | | | | | | | | | | Move common code into an extra function. This implicitly adds a missing node_info->fifo = CSR1212_INVALID_ADDR_SPACE; to .update. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: .probe and .update may sleepStefan Richter2007-04-29
| | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: coding styleStefan Richter2007-04-29
| | | | | | | | | | | | | | Adjust white space and line wraps. Remove unnecessary parentheses and braces, unused macros, and some of the more redundant comments. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: Move common recv_init code to helper functionJean Delvare2007-04-29
| | | | | | | | | | | | | | | | | | There is some common code between ether1394_open and ether1394_add_host which can be moved to a separate helper function for a slightly smaller eth1394 driver (-160 bytes on i386.) Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: don't autoload by hotplug when ohci1394 startsStefan Richter2007-04-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Until now, ieee1394 put an IP-over-1394 capability entry into each new host's config ROM. As soon as the controller was initialized --- i.e. right after modprobe ohci1394 --- this entry triggered a hotplug event which typically caused auto-loading of eth1394. This irritated or annoyed many users and distributors. Of course they could blacklist eth1394, but then ieee1394 wrongly advertized IP-over- 1394 capability to the FireWire bus. Therefore - remove the offending kernel config option IEEE1394_CONFIG_ROM_IP1394, - let eth1394 add the ROM entry by itself, i.e. only after eth1394 was loaded. This fixes http://bugzilla.kernel.org/show_bug.cgi?id=7793 . To emulate the behaviour of older kernels, simply add the following to to /etc/modprobe.conf: install ohci1394 /sbin/modprobe eth1394; \ /sbin/modprobe --ignore-install ohci1394 Note, autoloading of eth1394 when an _external_ IP-over-1394 capable device is discovered is _not_ affected by this patch. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: reduce excessive function inliningStefan Richter2007-04-29
| | | | | | | | | | | | | | | | | | Shrinks eth1394.ko by about 5%. Many of these functions have only one caller and are therefore auto- inlined anyway. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: clean up host removalStefan Richter2007-04-29
| | | | | | | | | | | | ether1394_add_host() guarantees that hi->dev != NULL if hi != NULL. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: eth1394: unregister address space in failure caseStefan Richter2007-04-29
| | | | | | | | | | | | | | Warn if hpsb_allocate_and_register_addrspace() failed. Unregister the address space if something else failed. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: send async streams at S100Stefan Richter2007-04-29
| | | | | | | | | | | | | | The comment says it all. This affects only asynchronous streams sent via raw1394; the eth1394 driver has own code and needs an own fix. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: SPIN_LOCK_UNLOCKED cleanupMilind Arun Choudhary2007-04-29
| | | | | | | | | | | | | | SPIN_LOCK_UNLOCKED cleanup,use DEFINE_SPINLOCK instead Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: nodemgr: unify some error messagesStefan Richter2007-04-29
| | | | | | | | | | | | Shrinks object file size a little bit. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: nodemgr: less noise in dmesgStefan Richter2007-04-29
| | | | | | | | | | | | | | Everytime when eth1394 or a libraw1394 client updates the configuration ROM, a certain sysfs attribute cannot be added since it already exists. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: unroll a weird macroStefan Richter2007-04-29
| | | | | | | | | | | | | | | | | | | | | | | | This is a coding style touch-up for ieee1394's handle_incoming_packet(). A preprocessor macro contained hardwired variable names and, even worse, the 'break' keyword. This macro is now unrolled and removed. Also, all 'break's which had the effect of a return are replaced by return. And a FIXME comment is brought up to date. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: iso.c needs sched.hAndrew Morton2007-04-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | alpha: drivers/ieee1394/iso.c: In function 'hpsb_iso_xmit_sync': drivers/ieee1394/iso.c:440: error: invalid use of undefined type 'struct task_struct' drivers/ieee1394/iso.c:440: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function) drivers/ieee1394/iso.c:440: error: (Each undeclared identifier is reported only once drivers/ieee1394/iso.c:440: error: for each function it appears in.) drivers/ieee1394/iso.c:440: warning: implicit declaration of function 'signal_pending' drivers/ieee1394/iso.c:440: error: invalid use of undefined type 'struct task_struct' drivers/ieee1394/iso.c:440: warning: implicit declaration of function 'schedule' drivers/ieee1394/iso.c: In function 'hpsb_iso_wake': drivers/ieee1394/iso.c:562: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function) Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (brought into alphabetic order)
| * ieee1394: some more includesStefan Richter2007-04-29
| | | | | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
| * ieee1394: ieee1394_transactions needs sched.hTorsten Kaiser2007-04-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | drivers/ieee1394/ieee1394_transactions.c fails for me if CONFIG_SMP=n gcc complains: CC drivers/ieee1394/ieee1394_transactions.o drivers/ieee1394/ieee1394_transactions.c: In function 'hpsb_get_tlabel': drivers/ieee1394/ieee1394_transactions.c:183: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function) drivers/ieee1394/ieee1394_transactions.c:183: error: (Each undeclared identifier is reported only once Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added comment)
| * ieee1394: ieee1394_core printk formatRandy Dunlap2007-04-29
| | | | | | | | | | | | | | | | Fix printk format string: drivers/ieee1394/ieee1394_core.c:702: warning: format '%d' expects type 'int', but argument 2 has type 'size_t' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-16 14:06:16 -0500