| Commit message (Collapse) | Author | Age |
|
|
|
|
| |
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
| |
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
| |
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
| |
Rename NET_SB1250_MAC to SB1250_MAC to follow the convention.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
| |
The SB1250 network interfaces are Gigabit Ethernet ones. Move the
Kconfig entry to the appropriate section and add some help text.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
| |
Resubmitting the patch.
This patch improves ethtool support for printing correct ring statistics,
segmentation offload status, etc.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
| |
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
| |
Since we are adding requirement for the PHYLIB for this driver, there should be a select for that
Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
| |
- add MDIO functions and register mdio bus
- add phy abstraction layer (PAL) functions and use PAL API
- test on STAMP537 board
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
| |
bf537mac_reset to bf537mac_disable
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Alex Landau writes in the forums:
Previously, changing the MAC address (e.g. via ifconfig) resulted
in a generic function to be called that only changed a variable in
memory. This patch also updated the Blackfin MAC address registers
to filter the correct new MAC.
Signed-off-by: Alex Landau <lirsb@yahoo.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
| |
- Update transceiver information in ethtool function
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Added set_mac_address driver entry point
- Copying permanent mac address to dev->perm_addr
- Incorporated following review comments from Jeff
- Converted the macro to a function and removed call to memset
- regarding function naming convention, for all callbacks and entry points
will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
| |
Removed bimodal interrupt support - unused feature
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
[also, trim trailing whitespace]
|
|
|
|
|
|
|
|
|
| |
- Changed kmalloc+memset to k[zc]alloc as per Mariusz's patch
<m.kozlowski@tuxland.pl>
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
| |
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
| |
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
|
|
| |
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
| |
This is nicer than the MAC_FMT stuff.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
| |
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the mac80211 based wireless drivers for the Intel
PRO/Wireless 3945ABG/BG Network Connection and Intel Wireless WiFi
Link AGN (4965) adapters.
[ Move driver into it's own directory -DaveM ]
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
| |
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
| |
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
SSB is an SoC bus used in a number of embedded devices. The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well. The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.
This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
| |
[ Ported to napi_struct changes... -DaveM ]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
| |
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
| |
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.
Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.
This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.
[ Resolved conflicts with napi_struct changes and fix sunqe build
regression... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
| |
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Code Optimization of s2io_isr function.
- Isr check using per device napi variable instead of driver global.
- Reduced from 3 to 1 if condition before check for processing packet receive
packets.
- Implemented Jeff's comment to use synchronize_irq. Removed the isr_cnt
variable as it became redundant.
- One time de assert the interrupts by writing all F's to the general_int_mask
register instead of de asserting by clearing the source of interrupts with
multiple writes which causes loss of interrupts (race conditions). It is
entirely possible that before the driver has a chance to mask the asserted
alarm bit, another alarm/traffic interrupt bit gets asserted as well. In
this case Herc will keep the INTA line asserted and the bridge will not
send a new Assert_INTA message upstream.
[ Resolved conflicts due to napi_struct changes... -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
| |
- Added check to return from the traffic handling function, if the card status
is DOWN.
- Implemented Jeff's comments on incorrect return value in s2io_poll function.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Removed the unused variable, intr_type, in device private structure.
[ Resolve conflicts with napi_struct changes... -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Added support to poll entire set of device errors and alarams.
- A note on how device errors and alarms are handled:
- The adapter will automatically recover from uncorrectable ECC errors.
Packets containing corrupted data will be dropped (not transmitted) or tagged
as invalid before being passed to the host.
- The adapter cannot recover from any internal state machine errors. A state
machine error requires a device reset.
- Any internal error that could potentially result in .store trampling.
(undesirable PCI behaviour)is tagged as a "serious error". In such cases
the adapter will give up its ability to be a bus master. In this situation
the host will still be able to read internal device registers in order to
generate an error report. A device reset is necessary to return to normal
operation.
- In the event of a pcix data parity error, the adapter will automatically
disable itself. Adapter_En will automatically transition from '1' to '0' and
the adapter will enter its clean-up routine. Once the device has achieved
quiescence, an adapter reset should be performed.
- Replaced alarm_intr_handler() with s2io_handle_errors().
- Added statistic counters to monitor the alarms.
[ Fix warnings wrt. do_s2io_chk_alarm_bit(), Callers pass in an
"unsigned long long *" but the function takes a "u64 *" which is
different on many 64-bit platforms. -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Added support to unmask entire set of device errors and alarams.
Alarm interrupts are generated for a myriad of purposes, ranging from
illegal operations or requests to internal state machine errors and
uncorrectable data corruption errors. In several cases the adapter can
recover gracefully from unexpected events; however, in some cases, a device
reset may be necessary. This patch handles alarms generated by all the
blocks within the device.
The adapter generates the following types of alarms:
1. Link state transitions (local/remote fault) or other link-related
problems.
2. Problems with any device peripherals, including the EEPROM, FLASH,
etc.
3. Correctable ECC errors (single-bit errors) on internal data
structures or frame data.
4. Uncorrectable ECC errors (multi-bit errors) on internal data
structures or frame data.
5. State machine errors, which indicate that internal control
structures have become corrupted.
6. PCI related errors, including parity errors or illegal transactions.
7. Other unexpected events.
- Implemented Jeff's review comments to use do_s2io_write_bits function to avoid
duplicate codes.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
| |
remove setup platform device from jazzsonic, which is done in arch code now
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
| |
The sgiseeq driver is one of the few remaining users of the ancient
cache banging DMA API. Replaced with the modern days DMA API.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
| |
The new microcode engine version is set to 1.1.0
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
| |
add driver recognition for T3C rev board.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
| |
Currently, the driver only tries up to 5 times (5us) to get the results
of a CQ context operation. Testing has shown the chip can take as much
as 50us to return the response on SG_CONTEXT_CMD operations. So we up
the retry count to 100 to cover high loads.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
| |
The cxgb3 driver is incorrectly configuring the HW CQ context for CQ's
that use overflow-avoidance. Namely the RDMA control CQ. This results
in a bad DMA from the device to bus address 0. The solution is to set
the CQ_ERR bit in the context for these types of CQs.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
| |
Qualify toggling of xgmac tx enable with not getting pause frames,
we might not make forward progress because the peer is sending
lots of pause frames.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
| |
Clear pciE PEX errors late at module load time.
Log details when PEX errors occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
| |
Update firmware version.
Allow the driver to be up and running with older FW image
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
| |
Since E100 timer is 2HZ, use rounding to make timer occur on the
correct boundary.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
|
|
|
|
|
| |
Removed the workaround that was needed for PS3 firmware versions
prior to the first release.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The PS3 virtual network device requires a vlan tag in the sending packet
to select the destination device, ethernet port or wireless.
As the vlan tag field is in the middle of the passed data,
we should insert it into the packet data.
To avoid copying much of the packet data, the driver used two tx descriptors
for one tx skb; one descriptor was for sending a small static
buffer which contained vlan tag and copied header (two mac addresses),
one was for the residual data after the vlan field.
This patch changes the way to insert the vlan tag. By changing
netdev->hard_header_len, we can make the headroom for moving mac address
fields in the skb buffer. Then we can send one tx skb with
one tx descriptor. This also gives us a tx throughut gain of approx.
20% according to netperf results.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|