aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAge
* isdn: remove extra byteswap in isdn_net_ciscohdlck_slarp_send_replyHarvey Harrison2008-11-17
| | | | | | | | | | commit a144ea4b7a13087081ab5402fa9ad0bcfd249e67 [IPV4]: annotate struct in_ifaddr Missed this extra byteswap as the isdn inlines hide the htonl inside put_u32 which causes an extra byteswap on little-endian arches. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: fix IPMI trafficJeff Kirsher2008-11-16
| | | | | | | | | | | | | | | Some users reported that they have machines with BMCs enabled that cannot receive IPMI traffic after e1000e is loaded. http://marc.info/?l=e1000-devel&m=121909039127414&w=2 http://marc.info/?l=e1000-devel&m=121365543823387&w=2 This fixes the issue if they load with the new parameter = 0 by disabling crc stripping, but leaves the performance feature on for most users. Based on work done by Hong Zhang. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: fix warn_on reload after phy_id errorJeff Kirsher2008-11-16
| | | | | | | | | | If the driver fails to initialize the first time due to the failure in the phy_id check the kernel triggers a warn_on on the second try to load the driver because the driver did not free the msi/x resources in the first load because of the previous failure in phy_id check. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: fix phy address bugGiulio Benetti2008-11-16
| | | | | | | | PHYID returns 0xffff and not 0xffffffff when not found and in some case(at91sam9263) 0x0. Maybe this patch could be useful. Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e100: fix dma error in direction for mappingJesse Brandeburg2008-11-16
| | | | | | | | | | | | | | The e100 driver triggers BUG_ON(buf->direction != dir) by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL) and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE). Changing the DMA direction, especially with dmabounce will result in unexpected behaviour. Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: use dev_printk instead of printkBjorn Helgaas2008-11-16
| | | | | | | | Use dev_printk() instead of printk() to give a little more context and use consistent format. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qla3xxx: Cleanup: Fix link print statements.Ron Mercer2008-11-16
| | | | | | | Removed debug print statements and improved conditionals around informational statements. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb: Use device_set_wakeup_enable\"Rafael J. Wysocki\2008-11-16
| | | | | | | | | | | | Since dev->power.should_wakeup bit is used by the PCI core to decide whether the device should wake up the system from sleep states, set/unset this bit whenever WOL is enabled/disabled using igb_set_wol(). Accordingly, use device_can_wakeup() for checking if wake-up is supported by the device. Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000: Use device_set_wakeup_enable\"Rafael J. Wysocki\2008-11-16
| | | | | | | | | | | | Since dev->power.should_wakeup bit is used by the PCI core to decide whether the device should wake up the system from sleep states, set/unset this bit whenever WOL is enabled/disabled using e1000_set_wol(). Accordingly, use device_can_wakeup() for checking if wake-up is supported by the device. Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: Use device_set_wakeup_enable\"Rafael J. Wysocki\2008-11-16
| | | | | | | | | | | | Since dev->power.should_wakeup bit is used by the PCI core to decide whether the device should wake up the system from sleep states, set/unset this bit whenever WOL is enabled/disabled using e1000_set_wol(). Accordingly, use device_can_wakeup() for checking if wake-up is supported by the device. Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* via-velocity: enable perfect filtering for multicast packetsJoey Zhuo2008-11-16
| | | | | | Signed-off-by: Joey Zhuo <joeyzhuo@via.com.tw> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: Add support for Marvell 88E1118 PHYRon Madrid2008-11-15
| | | | | | | This patch will add support for the Marvell 88E1118 PHY which supports gigabit ethernet among other things. Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* mlx4_en: Pause parameters per portYevgeny Petrilin2008-11-15
| | | | | | | | Before the change the driver reported the same pause parameters for all the ports, even only one of them was modified. Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'davem-fixes' of ↵David S. Miller2008-11-14
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
| * phylib: fix premature freeing of struct mii_busLennert Buytenhek2008-11-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 46abc02175b3c246dd5141d878f565a8725060c9 ("phylib: give mdio buses a device tree presence") added a call to device_unregister() in a situation where the caller did not intend for the device to be freed yet, but apart from just unregistering the device from the system, device_unregister() does an additional put_device() that is intended to free it. The right function to use in this situation is device_del(), which unregisters the device from the system like device_unregister() does, but without dropping the reference count an additional time. Bug report from Bryan Wu <cooloney@kernel.org>. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * atl1: Do not enumerate options unsupported by chipJ. K. Cliburn2008-11-14
| | | | | | | | | | | | | | | | | | Of the various WOL options provided in include/linux/ethtool.h, the L1 NIC supports only magic packet. Remove all options except magic packet from the atl1 driver. Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * atl1e: fix broken multicast by removing unnecessary crc inversionJ. K. Cliburn2008-11-14
| | | | | | | | | | | | | | | | | | | | Inverting the crc after calling ether_crc_le() is unnecessary and breaks multicast. Remove it. Tested-by: David Madore <david.madore@ens.fr> Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * gianfar: Fix DMA unmap invocationsAndy Fleming2008-11-14
| | | | | | | | | | | | | | | | We weren't unmapping DMA memory, which will break when gianfar gets used on systems with more than 32-bits of memory. Also, it's just plain wrong. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * net/ucc_geth: Fix oops in uec_get_ethtool_stats()Anton Vorontsov2008-11-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | p_{tx,rx}_fw_statistics_pram are special: they're available only when a device is open. If the device is closed, we should just fill the data with zeroes. Fixes the following oops: root@b1:~# ifconfig eth1 down root@b1:~# ethtool -S eth1 Unable to handle kernel paging request for data at address 0x00000000 Faulting instruction address: 0xc01e1dcc Oops: Kernel access of bad area, sig: 11 [#1] [...] NIP [c01e1dcc] uec_get_ethtool_stats+0x98/0x124 LR [c0287cc8] ethtool_get_stats+0xfc/0x23c Call Trace: [cfaadde0] [c0287ca8] ethtool_get_stats+0xdc/0x23c (unreliable) [cfaade20] [c0288340] dev_ethtool+0x2fc/0x588 [cfaade50] [c0285648] dev_ioctl+0x290/0x33c [cfaadea0] [c0272238] sock_ioctl+0x80/0x2ec [cfaadec0] [c00b5ae4] vfs_ioctl+0x40/0xc0 [cfaadee0] [c00b5fa8] do_vfs_ioctl+0x78/0x20c [cfaadf10] [c00b617c] sys_ioctl+0x40/0x74 [cfaadf40] [c00142d8] ret_from_syscall+0x0/0x38 [...] ---[ end trace b941007b2dfb9759 ]--- Segmentation fault p.s. While at it, also remove u64 casts, they aren't needed. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | niu: Bump driver version and release date.David S. Miller2008-11-14
| | | | | | | | | | | | | | | | | | | | This driver is pretty mature, and the worst of the known problems has been fixed (the 32-bit failures due to readq implementation). So let's finally give it a version of 1.0 Signed-off-by: David S. Miller <davem@davemloft.net>
* | NIU: Add Sun CP3260 ATCA blade supportSantwona Behera2008-11-14
|/ | | | | | | | | This patch adds support for the Sun CP3260 ATCA blade which is a N2 based ATCA blade with 2 NIU ports. The NIU ports do not have on-board PHY. Signed-off-by: Santwona Behera <santwona.behera@sun.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: fix poll_controller to pass proper structures and check all rx queuesNeil Horman2008-11-12
| | | | | | | | | | | | | Fix bnx2 so that netpoll works properly. Specifically: 1) Fix parameters to bnx2_interrupt to be a struct bnx2_napi rather than a struct net_device 2) Fix poll_controller method to check every queue in the rx case so frames aren't missed Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2008-11-12
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
| * hostap: pad the skb->cb usage in lieu of a proper fixJohannes Berg2008-11-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Like mac80211 did, this driver makes 'clever' use of skb->cb to pass information along with an skb as it is requeued from the virtual device to the physical wireless device. Unfortunately, that trick no longer works... Unlike mac80211, code complexity and driver apathy makes this hack the best option we have in the short run. Hopefully someone will eventually be motivated to code a proper fix before all the effected hardware dies. (Above text by me. Johannes officially disavows all knowledge of this hack. -- JWL) Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rtl8187 : support for Sitecom WL-168 0001 v4Bob Jolliffe2008-11-12
| | | | | | | | | | | | | | the Sitecom 0001 v4 with product id 0x0df6:0028, uses Realtek's RTL8187B and work fine with new 2.6.27 driver. Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rtl8187: Add Abocom USB IDIvan Kuten2008-11-12
| | | | | | | | | | | | Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | niu: Fix readq implementation when architecture does not provide one.David S. Miller2008-11-12
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a TX hang reported by Jesper Dangaard Brouer. When an architecutre cannot provide a fully functional 64-bit atomic readq/writeq, the driver must implement it's own. This is because only the driver can say whether doing something like using two 32-bit reads to implement the full 64-bit read will actually work properly. In particular one of the issues is whether the top 32-bits or the bottom 32-bits of the 64-bit register should be read first. There could be side effects, and in fact that is exactly the problem here. The TX_CS register has counters in the upper 32-bits and state bits in the lower 32-bits. A read clears the state bits. We would read the counter half before the state bit half. That first read would clear the state bits, and then the driver thinks that no interrupts are pending because the interrupt indication state bits are seen clear every time. Fix this by reading the bottom half before the upper half. Tested-by: Jesper Dangaard Brouer <jdb@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'davem-fixes' of ↵David S. Miller2008-11-11
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
| * [netdrvr] smc911x: fix for driver resume (and compilation warning)Dasgupta, Romit2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I am trying out suspend, resume on an OMAP3 based board. What I see during resume is that the SMC911x driver resume routing gets stuck after trying to transmit the packet out of the controller. Some debug messages below: --> smc911x_drv_resume eth0: --> smc911x_reset eth0: smc911x_reset timeout waiting for PM restore eth0: --> smc911x_enable eth0: --> smc911x_phy_configure() eth0: --> smc911x_phy_reset() eth0: phy caps=0x782d eth0: phy advertised caps=0x0de1 eth0: --> smc911x_phy_check_media smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809 smc911x_phy_read: phyaddr=0x1, phyreg=0x01, phydata=0x7809 eth0: link down Restarting tasks ... eth0: --> smc911x_hard_start_xmit eth0: --> smc911x_hardware_send_pkt eth0: --> smc911x_hard_start_xmit eth0: --> smc911x_hardware_send_pkt eth0: --> smc911x_hard_start_xmit eth0: --> smc911x_hardware_send_pkt nfs: server 172.24.190.217 not responding, still trying nfs: server 172.24.190.217 not responding, still trying The following change makes it work fine: (The change within smc911x_drv_probe function was to get rid of a compilation warning). Signed-off-by: Romit Dasgupta <romit@ti.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * RDMA/cxgb3: deadlock in iw_cxgb3 can cause hang when configuring interface.Steve Wise2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the iw_cxgb3 module's cxgb3_client "add" func gets called by the cxgb3 module, the iwarp driver ends up calling the ethtool ops get_drvinfo function in cxgb3 to get the fw version and other info. Currently the iwarp driver grabs the rtnl lock around this down call to serialize. As of 2.6.27 or so, things changed such that the rtnl lock is held around the call to the netdev driver open function. Also the cxgb3_client "add" function doesn't get called if the device is down. So, if you load cxgb3, then load iw_cxgb3, then ifconfig up the device, the iw_cxgb3 add func gets called with the rtnl_lock held. If you load cxgb3, ifconfig up the device, then load iw_cxgb3, the add func gets called without the rtnl_lock held. The former causes the deadlock, the latter does not. In addition, there are iw_cxgb3 sysfs handlers that also can call down into cxgb3 to gather the fw and hw versions. These can be called concurrently on different processors and at any time. Thus we need to push this serialization down in the cxgb3 driver get_drvinfo func. The fix is to remove rtnl lock usage, and use a per-device lock in cxgb3. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * cxgb3 - Limit multiqueue setting to msi-xDivy Le Ray2008-11-11
| | | | | | | | | | | | | | Allow multiqueue setting in MSI-X mode only Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * cxgb3 - eeprom read fixesDivy Le Ray2008-11-11
| | | | | | | | | | | | | | | | Protect against invalid phy entries in the eeprom. Extend eeprom access timeout. Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * myri10ge: fix stop/go ordering even moreBrice Goglin2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | The doorbell writes may be seen out of order by the firmware if they are in WC memory since the tx spin(un)lock does not flush WC writes. Hence if the "stop" is written on a different CPU than the "go", it is possible that the stop will arrive after the go unless we add an explicit memory barrier (and mmiowb() is not enough). It fixes transmit hangs in multi tx queue mode. Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | telephony: trivial: fix up email addressAlan Cox2008-11-11
| | | | | | | | | | Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | tty: trivial - fix up email addresses in tty related stuffAlan Cox2008-11-11
| | | | | | | | | | Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | Merge branch 'for_linus' of ↵Linus Torvalds2008-11-11
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6 * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (35 commits) V4L/DVB (9516): cx18: Move DVB buffer transfer handling from irq handler to work_queue V4L/DVB (9557): gspca: Small changes for the sensor HV7131B in zc3xx. V4L/DVB (9556): gspca: Bad init sequence for sensor HV7131B in zc3xx. V4L/DVB (9549): gspca: Fix a typo in one of gspca chips name. V4L/DVB (9515): cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup V4L/DVB (9493): kconfig patch V4L/DVB (9527): af9015: fix compile warnings V4L/DVB (9524): af9013: fix bug in status reading V4L/DVB (9511): cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call V4L/DVB (9510): cx18: Fix write retries for registers that always change - part 2. V4L/DVB (9506): ivtv/cx18: fix test whether modules should be loaded or not. V4L/DVB (9499): cx88-mpeg: final fix for analogue only compilation + de-alloc fix V4L/DVB (9496): cx88-blackbird: bugfix: cx88-blackbird-mpeg-users V4L/DVB (9495): cx88-blackbird: bugfix: cx88-blackbird-poll-fix V4L/DVB (9494): anysee: initialize anysee_usb_mutex statically V4L/DVB (9492): unplug oops from dvb_frontend_init... V4L/DVB (9486): ivtv/ivtvfb: no longer experimental V4L/DVB (9485): ivtv: remove incorrect V4L1 & tvaudio dependency V4L/DVB (9482): Documentation, especially regarding audio and informational links V4L/DVB (9475): cx18: Disable write retries for registers that always change - part 1. ...
| * | V4L/DVB (9516): cx18: Move DVB buffer transfer handling from irq handler to ↵Andy Walls2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | work_queue cx18: Move DVB buffer transfer handling from irq handler to work_queue thread. In order to properly lock the epu2cpu mailbox for driver to CX23418 commands, the DVB/TS buffer handling needs to be moved from the IRQ handler and IRQ context to a work queue. This work_queue implmentation is strikingly similar to the ivtv implementation - for better or worse. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9557): gspca: Small changes for the sensor HV7131B in zc3xx.Jean-Francois Moine2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | - touch only one register for brightness change - no quality control - don't probe again at streamon time. Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9556): gspca: Bad init sequence for sensor HV7131B in zc3xx.Jean-Francois Moine2008-11-11
| | | | | | | | | | | | | | | | | | | | | This patch fixes the H flip and the R & B color inversion of mode 320x240. Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9549): gspca: Fix a typo in one of gspca chips name.Krzysztof Helt2008-11-11
| | | | | | | | | | | | | | | | | | Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9515): cx18: Use correct Mailbox IRQ Ack values and misc IRQ ↵Andy Walls2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | handling cleanup cx18: Use correct Mailbox IRQ Ack values and misc IRQ handling cleanup. The SCB field definitions for Ack IRQ's for mailboxes were inconsistent with the bitmasks being loaded into those SCB fields and the SW2 Ack IRQ handling logic. Renamed fields in SCB to make things consistent and did misc IRQ handling cleanups: removing legacy ivtv dma_reg_lock, HPU IRQ flags, etc. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9493): kconfig patchFrederic CAND2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | Ok I made a patch that converts gspca kconfig file to a more standard= one, with tabs + 2 white spaces, so that if a warning is added it still compiles please find it attached Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9527): af9015: fix compile warningsAntti Palosaari2008-11-11
| | | | | | | | | | | | | | | | | | | | | - use static to avoid compile warnings Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9524): af9013: fix bug in status readingroel kluin2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | - ! has a higher precedence than & Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9511): cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API callAndy Walls2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | cx18: Mark CX18_CPU_DE_RELEASE_MDL as a slow API call. Give the encoder time to complete the MDL release before destroying the encoder internal task. This avoids an encoder lockup on the next digital capture and error messages about buffers being returned for an inactive encoder task handle. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9510): cx18: Fix write retries for registers that always change - ↵Andy Walls2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | part 2. cx18: Fix write retries for registers that always change - part 2. Some registers, especially interrupt related ones, will never read back the value just written. Modified interrupt register readback checks to make sure the intended effect was achieved. Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9506): ivtv/cx18: fix test whether modules should be loaded or not.Hans Verkuil2008-11-11
| | | | | | | | | | | | | | | Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9499): cx88-mpeg: final fix for analogue only compilation + ↵Darron Broad2008-11-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | de-alloc fix Final fix for when analogue only is selected for compilation (ie, !CX88_DVB) This tidies up previous fix and adds missing de-alloc memory leak on fault (eg, if fe1 fails to alloc where fe0 was allocated). Signed-off-by: Darron Broad <darron@kewl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9496): cx88-blackbird: bugfix: cx88-blackbird-mpeg-usersFrederic CAND2008-11-11
| | | | | | | | | | | | | | | | | | | | | Allows multiple access to the mpeg device Signed-off-by: Frederic CAND <frederic.cand@anevia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
| * | V4L/DVB (9495): cx88-blackbird: bugfix: cx88-blackbird-poll-fixFrederic CAND2008-11-11
| | | | | | | | | | | | | | | | | | | | | Starts encoder not only on a read call but also on a poll command. Signed-off-by: Frederic CAND <frederic.cand@anevia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-02-26 00:35:31 -0500