aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/usb/musb
Commit message (Collapse)AuthorAge
* USB: musb: partial DaVinci dm355 supportDavid Brownell2009-03-24
| | | | | | | | | | | | | | | | | | Partial support for DaVinci DM355, on the EVM board; peripheral mode should work, once mainline merges DM355 support. Missing: (a) renumbering the GPIO for DRVVBUS on the DM6446 EVM, when DAVINCI_N_GPIO increases; (b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is driven according to the ID signal, if cpu_is_..._dm355() The new PHY control bits are ignored on DM6446. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: only turn off vbus in OTG hostsAjay Kumar Gupta2009-03-24
| | | | | | | | | | | | | | | | | | | | | | Except on DaVinci, VBUS is now switched off as part of idling the USB link (after a_wait_bcon) whenever a device is disconnected from host. This is correct for OTG hosts, where either SRP or an ID interrupt could turn VBUS on again. However, for non-OTG hosts there's no way to turn VBUS on again, so the host becomes unusable. And the procfs entry which once allowed a manual workaround for this is now gone. This patch adds an is_otg_enabled() check before scheduling the switch-off timer in disconnect path, supporting a "classic host" mode where SRP is unavailable. [ dbrownell@users.sourceforge.net: tweak patch description ] Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: fix init oops crash with static FIFO configGiuseppe GORGOGLIONE2009-03-24
| | | | | | | | | | | | | | Correct musb_read_fifosize() and musb_configure_ep0() functions for the #ifndef BLACKFIN branch when the silicon uses static FIFO configuration. (Most current silicon configures this controller to use dynamic FIFO configuration; some parts from ST don't, like the STM STA2062.) Signed-off-by: Giuseppe GORGOGLIONE <giuseppe.gorgoglione@st.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: NAK timeout scheme on bulk RX endpointAjay Kumar Gupta2009-03-24
| | | | | | | | | | | | | | | | | | | | | | | | | | Fixes endpoint starvation issue when more than one bulk QH is multiplexed on the reserved bulk RX endpoint, which is normal for cases like serial and ethernet adapters. This patch sets the NAK timeout interval for such QHs, and when a timeout triggers the next QH will be scheduled. (This resembles the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.) This scheme doesn't work for devices which are connected to a high to full speed tree (transaction translator) as there is no NAK timeout interrupt from the musb controller from such devices. Tested with PIO, Inventra DMA, CPPI DMA. [ dbrownell@users.sourceforge.net: fold in start_urb() update; clarify only for bulk RX; don't accidentally clear WZC bits ] Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: rewrite host periodic endpoint allocationSergei Shtylyov2009-03-24
| | | | | | | | | | | | | | | | | | | | | | The current MUSB host code doesn't make use of all the available FIFOs in for periodic transfers since it wrongly assumes the RX and TX sides of any given hw_ep always share one FIFO. Change: use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep' to check the endpoint's business; get rid of the now-unused 'periodic' array in the 'struct musb'. Also optimize a loop induction variable in the endpoint lookup code. (Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>) [ dbrownell@users.sourceforge.net: clarify description and origin of this fix; whitespace ] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: replace uses of __constant_{endian}Harvey Harrison2009-03-24
| | | | | | | | The base versions handle constant folding now. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: fix srp sysfs entry deletionVikram Pandita2009-02-27
| | | | | | | | | | | | The SRP sysfs attribute is dependent on gadget mode; any gadget may support SRP. But "rmmod musb_hdrc" didn't remove that attribute; fix. Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Acked-by: Felipe Balbi <me@felipebalbi.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: resume suspended root hub on disconnectAnand Gadiyar2009-02-27
| | | | | | | | | | | | | | | If this is not done, khubd will not be informed of the disconnect and will assume the device is still there. Easily seen when a hub is connected with no device attached to it; it will autosuspend. When the hub is disconnected, it still shows up in /proc/bus/usb/devices Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: use right poll limit for low speed devicesSergei Shtylyov2009-02-27
| | | | | | | | | | | Remove wrongly applied upper limit on the interrupt transfer interval for low speed devices (not much of an error per se, according to USB specs). Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: be careful with 64K+ transfer lengths, host sideSergei Shtylyov2009-02-27
| | | | | | | | | | | | | | | | Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO count in musb_host_tx() risks sending a short packet prematurely for transfer sizes over 64 KB. Similarly, although data transfer size shouldn't exceed 65535 bytes for the control endpoint, making musb_h_ep0_continue() more robust WRT URBs with possibly oversized buffer will not hurt either... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: fix data toggle saving with shared FIFOSergei Shtylyov2009-02-27
| | | | | | | | | | | | | For some strange reason the host side musb_giveback() decides that it's always got an IN transfer when the hardware endpoint is using a shared FIFO. This causes musb_save_toggle() to read the toggle state from the RXCSR register instead of TXCSR, and may also cause unneeded reloading of RX endpoint registers. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: host endpoint_disable() oops fixesSergei Shtylyov2009-02-27
| | | | | | | | | | | | | | | | | | | | | | The musb_h_disable() routine can oops in some cases: - It's not safe to read hep->hcpriv outside musb->lock, since it gets changed on completion IRQ paths. - The list iterators aren't safe to use in that way; just remove the first element while !list_empty(), so deletions on other code paths can't make trouble. We need two "scrub the list" loops because only one branch should touch hardware and advance the schedule. [ dbrownell@users.sourceforge.net: massively simplify patch description; add key points as code comments ] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: fix urb_dequeue() methodSergei Shtylyov2009-02-27
| | | | | | | | | | | | | | | | | | | | | | | The urb_dequeue() method forgets to unlink 'struct musb_qh' from the control or bulk schedules when the URB being cancelled is the only one queued to its endpoint. That will cause musb_advance_schedule() to block once it reaches 'struct musb_qh' with now empty URB list, so URBs queued for other endpoints after the one being dequeued will not be served. Fix by unlinking the QH from the list except when it's already being handled (typically by musb_giveback). Since a QH with an empty URB list is now supposed to be freed, do that. And remove a now-useless check from musb_advance_schedule(). [ dbrownell@users.sourceforge.net: update patch description, and fold in a dequeue() comment patch ] Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: fix musb_host_tx() for shared endpoint FIFODmitry Krivoschekov2009-02-27
| | | | | | | | | | | | | | | | | | The input queue should be used for TX on endpoints which share FIFO hardware. The host TX path wasn't doing that. Shared FIFOs are most often configured for periodic endpoints, which are mostly used for RX/IN transfers ... that's probably how this bug managed to linger for a long time. [ dbrownell@users.sourceforge.net: update patch description ] Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: be careful with 64K+ transfer lengths (gadget side)Felipe Balbi2009-02-27
| | | | | | | | | | | | | request->actual is an unsigned and we should use the same variable type for fifo_count otherwise we might lose some data if request->length >= 64kbytes. [ dbrownell@users.sourceforge.net: fix compiler warning ] Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: make Davinci *work* in mainlineDavid Brownell2009-02-27
| | | | | | | | | | | | | | | | | | | | | | | | | Now that the musb build fixes for DaVinci got merged (RC3?), kick in the other bits needed to get it finally *working* in mainline: - Use clk_enable()/clk_disable() ... the "always enable USB clocks" code this originally relied on has since been removed. - Initialize the USB device only after the relevant I2C GPIOs are available, so the host side can properly enable VBUS. - Tweak init sequencing to cope with mainline's relatively late init of the I2C system bus for power switches, transceivers, and so on. Sanity tested on DM6664 EVM for host and peripheral modes; that system won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also verified on OMAP3. (Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <me@felipebalbi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: Kconfig fixDavid Brownell2009-01-27
| | | | | | | | | | | The Blackfin MUSB Kconfig text didn't properly parenthesise its dependencies. This was visible in non-Blackfin configs by the way the user interfaces lost track of dependencies, when doing a bunch of test builds. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb cppi dma fixSwaminathan S2009-01-27
| | | | | | | | | | Initializes the actual_len field to 0 before every DMA transaction. Signed-off-by: Swaminathan S <swami.iyer@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb cppi bugfixesHugo Villeneuve2009-01-27
| | | | | | | | | | | | | | | These compilation errors are related to incorrect debugging macro and variable names and generated the following errors: drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment': drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function) Signed-off-by: Hugo Villeneuve <hugo@hugovil.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb uses endpoint functionsJulia Lawall2009-01-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This set of patches introduces calls to the following set of functions: usb_endpoint_dir_in(epd) usb_endpoint_dir_out(epd) usb_endpoint_is_bulk_in(epd) usb_endpoint_is_bulk_out(epd) usb_endpoint_is_int_in(epd) usb_endpoint_is_int_out(epd) usb_endpoint_num(epd) usb_endpoint_type(epd) usb_endpoint_xfer_bulk(epd) usb_endpoint_xfer_control(epd) usb_endpoint_xfer_int(epd) usb_endpoint_xfer_isoc(epd) In some cases, introducing one of these functions is not possible, and it just replaces an explicit integer value by one of the following constants: USB_ENDPOINT_XFER_BULK USB_ENDPOINT_XFER_CONTROL USB_ENDPOINT_XFER_INT USB_ENDPOINT_XFER_ISOC An extract of the semantic patch that makes these changes is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r1@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) == - \(USB_ENDPOINT_XFER_CONTROL\|0\)) + usb_endpoint_xfer_control(epd) @r5@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) == - \(USB_DIR_IN\|0x80\)) + usb_endpoint_dir_in(epd) @inc@ @@ #include <linux/usb.h> @depends on !inc && (r1||r5)@ @@ + #include <linux/usb.h> #include <linux/usb/...> // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: tusb6010 buildfixKalle Valo2009-01-27
| | | | | | | | | | | | | drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h: No such file or directory drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h: No such file or directory Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb free_irq bugfixAjay Kumar Gupta2009-01-27
| | | | | | | | | | | Fixes insert module failure as free_irq() was not done in previous rmmod. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb_hdrc: another davinci buildfix (otg related)David Brownell2009-01-27
| | | | | | | | | | The DaVinci code had an implementation of the OTG transceiver glue too; make it use the new-standard one. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb davinci buildfixDavid Brownell2009-01-27
| | | | | | | | | | | | | | | | | | Trying once more to get this merged. The original was submitted for 2.6.27-rc2 or so, and never got correctly merged. Neither were any of the numerous subsequent resends. Sigh. CC drivers/usb/musb/davinci.o drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode' drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: Kill some compiling warning in musb Blackfin partBryan Wu2009-01-07
| | | | | | | Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: Blackfin provides read/write I/O accessor in header filesBryan Wu2009-01-07
| | | | | | | | | Don't redefine the functions in musb driver Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: add Blackfin Kconfig options and MakefileBryan Wu2009-01-07
| | | | | | | Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: add Blackfin specific configuration to MUSBBryan Wu2009-01-07
| | | | | | | | | | | | | Some config registers are not avaiable in Blackfin, we have to comment them out. v1-v2: - remove Blackfin specific header file - add Blackfin register version to musb_regs.h header file Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: enable low level DMA operation for BlackfinBryan Wu2009-01-07
| | | | | | | | | | - DMA registers in Blackfin have different layout - DMA interrupt flags need to be cleared by software Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: add Blackfin version low level register accessing helper functionsBryan Wu2009-01-07
| | | | | | | | | add Blackfin version low level register accessing helper functions Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: Make sure we program the correct values in only when necessary.Robin Getz2009-01-07
| | | | | | | | | | Make sure we program the correct values in only when necessary. Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: add Blackfin driver to MUSB framework (v2)Bryan Wu2009-01-07
| | | | | | | | | | | - replace MUSB_FIFOSIZE register to MUSB_TXCOUNT, cause no MUSB_FIFOSIZE register on Blackfin - use #ifdef to replace #if defined() Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: check if set_irq_wake succeded and remember itFelipe Balbi2009-01-07
| | | | | | | | | Without it, in platforms that don't provide irq_chip.set_wake(), like omap, musb will WARN() on driver removal. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: host side diagnostics tweaksDavid Brownell2009-01-07
| | | | | | | | | | | | | | | | | | | | | | | Random host-side MUSB updates, mostly relating to better diagnostics: + Improve diagnostics on host side: - tx flush fifo: * Avoid hundreds of duplicate TX FIFONOTEMPTY messages * make "Can't flush TX fifo" a warning, and say which endpoint - giveback: * use correct status code * show completion function name not just URB pointer - Fix annoying "1 bytes" (should be "1 byte") + Be more consistent about failing init of unusable fifo_mode It's not clear why that "can't flush TX fifo" message appears, though it might relate to disconnection; I see it not infrequently Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: minor locking fixDavid Brownell2009-01-07
| | | | | | | | | | | Minor locking fix for musb_hdrc on OMAP3 and OMAP2430: don't read DEVCTL without holding the spinlock, since an IRQ could come in and corrupt things. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: build fixes for DaVinciKevin Hilman2009-01-07
| | | | | | | | | | - update includes after asm/arch --> mach headers move - adds musb_platform_set_mode() stub Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: musb: sysfs mode updatesDavid Brownell2009-01-07
| | | | | | | | | | | | | | Fix three omissions in the "mode" sysfs attribute support: (a) inability to report errors; (b) no DaVinci support ... just report an error; (c) for omap2430, accepting unsupportable values The 2430 stuff is still odd.... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers2009-01-07
| | | | | | Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: fix bug in musb_scheduleFelipe Balbi2008-11-20
| | | | | | | | | | This bug was introduced recently. Fix it before bigger problems appear. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: fix BULK request on different available endpointsAjay Kumar Gupta2008-11-13
| | | | | | | | | | | | | | | | | | | Fixes co-working issue of usb serial device with usb/net devices while oter endpoints are free and can be used.This patch implements the policy that if endpoint resources are available then different BULK request goes to different endpoint otherwise they are multiplexed to one reserved endpoint as currently done. Switch statement case is reordered in musb_giveback() to take care of bulk request both in multiplex scenario and otherwise. NAK limit scheme has to be added for multiplexed BULK request scenario to avoid endpoint starvation due to usb/net devices. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: fix debug global variable nameFelipe Balbi2008-11-13
| | | | | | | | | In order to avoid namespace conflicts, add a prefix to our kernel-wise symbol. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: Removes compilation warning in gadget modeAjay Kumar Gupta2008-11-13
| | | | | | | | | Fixes compilation warning when musb is configured in gadget mode. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: tusb6010: kill compile warningFelipe Balbi2008-11-13
| | | | | | | | Add an errno to failing case. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: Fix for isochronous IN transferAjay Kumar Gupta2008-11-13
| | | | | | | | | | | Fixes blurred capture images in dma mode. Isochronous error field in urb and source data buffer pointer were not updated properly in dma mode. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: remove dead code from procfsFelipe Balbi2008-10-17
| | | | | | | | | | | When removing the procfs file, I forgot to remove some code that created and removed that file. Here's a patch to fix it. Ideally this patch will be melded into the patch removing the procfs file, don't know if it's possible still. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: general cleanup to musbhsdma.cFelipe Balbi2008-10-17
| | | | | | | | | Basically getting rid of CaMeLcAsE, but also adding missing lines and spaces. Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb_hdrc build fixesDavid Brownell2008-10-17
| | | | | | | | | | | | | | | | | | | | | | | | | Minor musb_hdrc updates: - so it'll build on DaVinci, given relevant platform updates; * remove support for an un-shipped OTG prototype * rely on gpiolib framework conversion for the I2C GPIOs * the <asm/arch/hdrc_cnf.h> mechanism has been removed - catch comments up to the recent removal of the per-SOC header with the silicon configuration data; - and remove two inappropriate "inline" declarations which just bloat host side code. There are still some more <asm/arch/XYZ.h> ==> <mach/XYZ.h> changes needed in this driver, catching up to the relocation of most of the include/asm-arm/arch-* contents. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Cc: stable <stable@kernel.org> [2.6.27] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* usb: musb: do not mess up count number and CSR0 register valueBryan Wu2008-10-17
| | | | | | | Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* OMAP:MUSB: Corrects urb unlink function pathAjay Kumar Gupta2008-10-17
| | | | | | | | | | | | | | | Fixes kernel panic while ISO IN transfer is aborted.Replaced usb_hcd_unlink_urb_from_ep() from musb_giveback() to __musb_giveback() to make sure urb is unlinked before giveback when __musb_giveback() is called from musb_urb_dequeue(). Acquired musb->lock() before usb_hcd_unlink_urb_from_ep() within in enqueue path. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* OMAP:MUSB: Fixes the TT programming.Ajay Kumar Gupta2008-10-17
| | | | | | | | | | | Fixes enumeration failures when a USB device attached to a LS hub is connected to OMAP EVM via HS hub. This is fixed by correctly programming hub address register in enqueue path. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-27 08:18:22 -0500