| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This is caused by tty_release using tty_lock_pair to lock both sides of
the pty/tty pair, and then tty_ldisc_release dropping and relocking one
side only. We can drop both fine, so drop both to avoid any lock
ordering concerns.
Rework the release path to fix the new locking model.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
The ptmx_open path takes the tty and devpts locks in the wrong order
because tty_init_dev locks and returns a locked tty. As far as I can
tell this is actually safe anyway because the tty being returned is new
so nobody can get a reference to lock it at this point.
However we don't even need the devpts lock at this point, it's only held
as a byproduct of the way the locks were pushe down.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | | |
Updated to resolve dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | |\
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | |\ \ \ \
| | |_|/ /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
into next/clock
Shawn Guo <shawn.guo@linaro.org> writes:
mxs common clk porting for v3.5. It depends on the following two branches.
[1] git://git.linaro.org/people/mturquette/linux.git clk-next
[2] http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm.git clkdev
As the mxs device tree conversion will constantly touch clock files,
to save the conflicts, the updated mxs/dt branch coming later will
based on this pull-request.
* 'clk/mxs' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: remove now unused timer_clk argument from mxs_timer_init
ARM: mxs: remove old clock support
ARM: mxs: switch to common clk framework
ARM: mxs: change the lookup name for fec phy clock
ARM: mxs: request clock for timer
clk: mxs: add clock support for imx28
clk: mxs: add clock support for imx23
clk: mxs: add mxs specific clocks
Includes an update to Linux 3.4-rc6
Conflicts:
drivers/clk/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |/ /
| |/| |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull the MCA deletion branch from Paul Gortmaker:
"It was good that we could support MCA machines back in the day, but
realistically, nobody is using them anymore. They were mostly limited
to 386-sx 16MHz CPU and some 486 class machines and never more than
64MB of RAM. Even the enthusiast hobbyist community seems to have
dried up close to ten years ago, based on what you can find searching
various websites dedicated to the relatively short lived hardware.
So lets remove the support relating to CONFIG_MCA. There is no point
carrying this forward, wasting cycles doing routine maintenance on it;
wasting allyesconfig build time on validating it, wasting I/O on git
grep'ping over it, and so on."
Let's see if anybody screams. It generally has compiled, and James
Bottomley pointed out that there was a MCA extension from NCR that
allowed for up to 4GB of memory and PPro-class machines. So in *theory*
there may be users out there.
But even James (technically listed as a maintainer) doesn't actually
have a system, and while Alan Cox claims to have a machine in his cellar
that he offered to anybody who wants to take it off his hands, he didn't
argue for keeping MCA support either.
So we could bring it back. But somebody had better speak up and talk
about how they have actually been using said MCA hardware with modern
kernels for us to do that. And David already took the patch to delete
all the networking driver code (commit a5e371f61ad3: "drivers/net:
delete all code/drivers depending on CONFIG_MCA").
* 'delete-mca' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MCA: delete all remaining traces of microchannel bus support.
scsi: delete the MCA specific drivers and driver code
serial: delete the MCA specific 8250 support.
arm: remove ability to select CONFIG_MCA
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.
This commit removes the MCA specific 8250 UART code.
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-serial@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform changes from Ingo Molnar:
"This tree includes assorted platform driver updates and a preparatory
series for a platform with custom DMA remapping semantics (sta2x11 I/O
hub)."
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vsmp: Fix number of CPUs when vsmp is disabled
keyboard: Use BIOS Keyboard variable to set Numlock
x86/olpc/xo1/sci: Report RTC wakeup events
x86/olpc/xo1/sci: Produce wakeup events for buttons and switches
x86, platform: Initial support for sta2x11 I/O hub
x86: Introduce CONFIG_X86_DMA_REMAP
x86-32: Introduce CONFIG_X86_DEV_DMA_OPS
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The PC BIOS does provide a NUMLOCK flag containing the desired state
of this LED. This patch sets the current state according to the data
in the bios.
[ hpa: fixed __weak declaration without definition, changed "inline"
to "static inline" ]
Signed-Off-By: Joshua Cov <joshuacov@googlemail.com>
Link: http://lkml.kernel.org/r/CAKL7Q7rvq87TNS1T_Km8fW_5OzS%2BSbYazLXKxW-6ztOxo3zorg@mail.gmail.com
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
| |\ \ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Pull SuperH updates from Paul Mundt:
- New CPUs: SH7734 (SH-4A), SH7264 and SH7269 (SH-2A)
- New boards: RSK2+SH7264, RSK2+SH7269
- Unbreaking kgdb for SMP
- Consolidation of _32/_64 page fault handling.
- watchdog and legacy DMA chainsawing, part 1
- Conversion to evt2irq() hwirq lookup, to support relocation of
vectored IRQs for irqdomains.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (98 commits)
sh: intc: Kill off special reservation interface.
sh: Enable PIO API for hp6xx and se770x.
sh: Kill off machvec IRQ hinting.
sh: dma: More legacy cpu dma chainsawing.
sh: Kill off MAX_DMA_ADDRESS leftovers.
sh: Tidy up some of the cpu legacy dma header mess.
sh: Move sh4a dma header from cpu-sh4 to cpu-sh4a.
sh64: Fix up vmalloc fault range check.
Revert "sh: Ensure fixmap and store queue space can co-exist."
serial: sh-sci: Fix for port types without BRI interrupts.
sh: legacy PCI evt2irq migration.
sh: cpu dma evt2irq migration.
sh: sh7763rdp evt2irq migration.
sh: sdk7780 evt2irq migration.
sh: migor evt2irq migration.
sh: landisk evt2irq migration.
sh: kfr2r09 evt2irq migration.
sh: ecovec24 evt2irq migration.
sh: ap325rxa evt2irq migration.
sh: urquell evt2irq migration.
...
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In doing the evt2irq() + muxed vector conversion for various port types
it became apparent that some of the legacy port types will presently
error out due to the irq requesting logic attempting to acquire the
non-existent BRI IRQ. This adds some sanity checks to the request/free
path to ensure that non-existence of a source in itself is not an error.
This should restore functionality for legacy PORT_SCI ports.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | |\ \ \ \ \ \
| | | |/ / / /
| | |/| | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Conflicts:
arch/sh/kernel/cpu/sh3/setup-sh770x.c
arch/sh/kernel/cpu/sh3/setup-sh7710.c
arch/sh/kernel/cpu/sh3/setup-sh7720.c
arch/sh/kernel/cpu/sh4/setup-sh7750.c
arch/sh/kernel/cpu/sh4a/setup-sh7343.c
arch/sh/kernel/cpu/sh4a/setup-sh7366.c
arch/sh/kernel/cpu/sh4a/setup-sh7722.c
arch/sh/kernel/cpu/sh4a/setup-sh7723.c
arch/sh/kernel/cpu/sh4a/setup-sh7724.c
arch/sh/kernel/cpu/sh4a/setup-sh7757.c
arch/sh/kernel/cpu/sh4a/setup-sh7763.c
arch/sh/kernel/cpu/sh4a/setup-sh7770.c
arch/sh/kernel/cpu/sh4a/setup-sh7785.c
arch/sh/kernel/cpu/sh4a/setup-sh7786.c
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | |\ \ \ \ \ \
| | | |_|_|/ /
| | |/| | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Conflicts:
arch/sh/Kconfig
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | |\ \ \ \ \ \ |
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This updates the earlier break_ctl support regardless of regtype so long
as the requisite SCSPTR exists. This is the same approach used by
sci_init_pins() for providing a generic solution now that we're able to
detect register capabilities on a per-port basis.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| | | |_|_|/ / /
| |/| | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
SCIF modules which have SCSPTR can output the break signal. Now that we
have a way of determining port features/capabilities, add trivial break
control via SCSPTR support. Tested on sh7757lcr.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
| |\ \ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY updates from Greg Kroah-Hartman:
"Here's the big TTY/serial driver pull request for the 3.5-rc1 merge
window.
Nothing major in here, just lots of incremental changes from Alan and
Jiri reworking some tty core things to behave better and to get a more
solid grasp on some of the nasty tty locking issues.
There are a few tty and serial driver updates in here as well.
All of this has been in the linux-next releases for a while with no
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (115 commits)
serial: bfin_uart: Make MMR access compatible with 32 bits bf609 style controller.
serial: bfin_uart: RTS and CTS MMRs can be either 16-bit width or 32-bit width.
serial: bfin_uart: narrow the reboot condition in DMA tx interrupt
serial: bfin_uart: Adapt bf5xx serial driver to bf60x serial4 controller.
Revert "serial_core: Update buffer overrun statistics."
tty: hvc_xen: NULL dereference on allocation failure
tty: Fix LED error return
tty: Allow uart_register/unregister/register
tty: move global ldisc idle waitqueue to the individual ldisc
serial8250-em: Add DT support
serial8250-em: clk_get() IS_ERR() error handling fix
serial_core: Update buffer overrun statistics.
tty: drop the pty lock during hangup
cris: fix missing tty arg in wait_event_interruptible_tty call
tty/amiserial: Add missing argument for tty_unlock()
tty_lock: Localise the lock
pty: Lock the devpts bits privately
tty_lock: undo the old tty_lock use on the ctty
serial8250-em: Emma Mobile UART driver V2
Add missing call to uart_update_timeout()
...
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
controller.
Simplify serial data width calculation and adapt to bf609 LCR bit mask.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Change hardware flow control code to adapt to both bf5xx and bf60x.
Disabled serial device before set termios for bf60x.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Check if xmit buffer pointers are set to zero.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The serial4 controller on bf60x is an enhanced version of serial controller
on bf5xx. MMR size is 32 bits other than 16 bits. MMR GCTL, MCR and LCR are
combined into one control MMR. MSR and LSR are combined into one status MMR.
This patch adapts current bf5xx serial driver to serial4 controller on bf60x.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This reverts commit 642180871bc91afebb6ccf40d1615a7dd33699a3.
Buffer overruns are for hardware reported overruns, not software ones,
which will only happen if we run out of memory and you will get lots of
-ENOMEM errors at the same time.
Thanks to Alan Cox for catching this.
Reported-by: Alan Cox <alan@linux.intel.com>
Cc: Corbin Atkinson <corbinat@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
If kzalloc() returns a NULL here, we pass a NULL to
xencons_disconnect_backend() which will cause an Oops.
Also I removed the __GFP_ZERO while I was at it since kzalloc() implies
__GFP_ZERO.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
3.4-rc introduced a regression when setting the LEDS. We do the right thing
but then return an error code.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43144
Reported-by: Christian Casteyde
Signed-off-by: Alan Cox <alan@linux/intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This is legitimate but because we don't clear the drv->state pointer in the
unregister code causes a bogus BUG().
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42880
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The global wait_queue that is used for line discipline idle handling is
moved to a separate wait_queue for each line instance. This prevents
unnecessary blocking on one line, because of idle handling on another
line.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Update the 8250_em driver to support DT.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Update the 8250_em driver to correctly handle the case
where no clock is associated with the device.
The return value of clk_get() needs to be checked with
IS_ERR() to avoid NULL pointer referencing.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Currently, serial drivers don't report buffer overruns. When a buffer overrun
occurs, tty_insert_flip_char returns 0, and no attempt is made to insert that
same character again (i.e. it is lost). This patch reports buffer overruns via
the buf_overrun field in the port's icount structure.
Signed-off-by: Corbin Atkinson <corbin.atkinson@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
In theory we don't need it, in practice we are hitting some ill understood
deadlock when we don't drop it. The old code dropped it here so we are not
undoing anything problematic for pty. If pty could be unloaded it would be
a problem but it can't.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Commit d29f3ef39be4eec0362b985305fc526d9be318cf
"tty_lock: Localise the lock"
added a tty arg to wait_event_interruptible_tty() but it missed
this arch specific instance for cris, causing a compile failure.
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
commit d29f3ef39be4eec0362b985305fc526d9be318cf ("tty_lock: Localise the lock")
missed that d3a7b83f865b46bb7b5e1ed18a129ce1af349db4 ("drivers/tty/amiserial.c:
add missing tty_unlock") just added a new caller of tty_unlock():
drivers/tty/amiserial.c: In function ‘set_serial_info’:
drivers/tty/amiserial.c:1077: error: too few arguments to function ‘tty_unlock’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
In each remaining case the tty_lock is associated with a specific tty. This
means we can now lock on a per tty basis. We do need tty_lock_pair() for
the pty case. Uglier but still a step in the right direction.
[fixed up calls in 3 missing drivers - gregkh]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This is a private pty affair, we don't want to tangle it with the tty_lock
any more as we know all the other non tty locking is now handled by the vfs
so we too can move.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
get_current_tty has its own consistent locking. That means a pile of the
tty lock cases are not needed. As get_current_tty also keeps a reference the
tty object lifetime means we can propogate the lock removal out.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This is V2 of the Emma Mobile 8250 platform driver.
The hardware itself has according to the data sheet
up to 64 byte FIFOs but at this point we only make
use of the 16550 compatible mode.
To support this piece of hardware the common UART
registers need to be remapped, and the access size
differences need to be handled.
The DLL and DLM registers can due to offset collision
not be remapped easily, and because of that this
driver makes use of ->dl_read() and ->dl_write()
callbacks. This in turn requires a registration
function that takes 8250-specific paramenters.
Future potential enhancements include DT support,
early platform driver console and fine grained PM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This patch fixes a problem reported here:
http://article.gmane.org/gmane.linux.ports.arm.kernel/155242/match=auart
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The variable 'mxser_port_ops' is only referenced in this file and
should be marked static to prevent it from being exposed globally.
Quites the sparse warning:
warning: symbol 'mxser_port_ops' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Introduce yet another 8250 registration function.
This time it is serial8250_register_8250_port() and it
allows us to register 8250 hardware instances using struct
uart_8250_port. The new function makes it possible to
register 8250 hardware that makes use of 8250 specific
callbacks such as ->dl_read() and ->dl_write().
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Get rid of unused functions and macros now when
Alchemy and RM9K are converted over to callbacks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Convert the 8250 RM9K support code to make
use of the new dl_read()/dl_write() callbacks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Convert the 8250 Alchemy support code to make
use of the new dl_read()/dl_write() callbacks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Convert serial_dl_read() and serial_dl_write() from macro
to 8250 specific callbacks. This change makes it easier to
support 8250 hardware with non-standard DLL and DLM register
configurations such as Alchemy, RM9K and upcoming Emma Mobile
UART hardware.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
We noticed that we were loosing data at speed less than 2400 baud.
It turned out our (TI16750 compatible) uart with 64 byte outgoing fifo
was truncated to 16 byte (bit 5 sets fifo len) when modifying the fcr
reg.
The input code still fills the buffer with 64 bytes if I remember
correctly and thus data is lost.
Our fix was to remove whiping of the fcr content and just add the
TRIGGER_1 which we want for latency.
I can't see why this would not work on less than 2400 always, for all
uarts ...
Otherwise one would have to make sure the filling of the fifo re-checks
the current state of available fifo size (urrk).
Signed-off-by: Christian Melki <christian.melki@ericsson.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The rules used to make 8250_pci "ignore" the PCH uarts are lacking pci subids
entries, preventing it to match and thus is breaking serial port support for
theses systems.
This has been tested on a nanoETXexpress-TT, which has a specifici uart clock.
Tested-by: Erwan Velu <Erwan.Velu@zodiacaerospace.com>
[stable@: please apply to 3.0-stable, 3.2-stable and 3.3-stable]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnaud Patard <apatard@hupstream.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
copy_from_read_buf currently copies data to a user buffer and then
checks if the data is single EOF. But it checks it by accessing the
user buffer. First, the buffer may be changed by other threads of the
user program already. Second, it accesses the buffer without any
checks. It might be write-only for example.
Fix this by inspecting contents of the tty (kernel) buffer instead.
Note that "n == 1" is necessary, but not sufficient. But we check
later that there is nothing left by "!tty->read_cnt" condition.
There is still an issue with the current code that EOF being wrapped
to the start of the circular buffer will result in an inappropriate
losing of the EOF character. But this is not intended to be fixed by
this patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Emil Goode <emilgoode@gmail.com>
Cc: Howard Chu <hyc@symas.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
When we do this it becomes clear the lock we should be holding is the vc
lock, and in fact many of our other helpers are properly invoked this way.
We don't at this point guarantee not to race the keyboard code but the results
of that appear harmless and that was true before we started as well.
We now have no users of tty_lock in the console driver...
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |\ \ \ \ \ \ \
| | |_|_|_|_|/ /
| |/| | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
This resolves the merge problem with:
drivers/tty/serial/pch_uart.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
