aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/scsi/device_handler
Commit message (Collapse)AuthorAge
* [SCSI] scsi_dh_rdac: Retry for NOT_READY check conditionChauhan, Vijay2009-03-17
| | | | | | | | This patch adds retry for NOT_READY check condition - Quiesce in progress (02/A1/02) Signed-off-by: Vijay Chauhan<vijay.chauhan@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh_rdac: Retry mode select for NO_SENSE, ABORTED_COMMAND, ↵Chauhan, Vijay2009-03-12
| | | | | | | | | | | | | UNIT_ATTENTION, NOT_READY(02/04/01) This patch is to add retry for mode select if mode select command is returned with sense NO_SENSE, UNIT_ATTENTION, ABORTED_COMMAND, NOT_READY(02/04/01). This patch reorganise the sense keys from if-else to switch-case format for better maintainability. Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com> Acked-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh_rdac: Retry for Quiescence in Progress in rdac device handlerChauhan, Vijay2009-03-12
| | | | | | | | | | | During device discovery read capacity fails with 0x068b02 and sets the device size to 0. As a reason any I/O submitted to this path gets killed at sd_prep_fn with BLKPREP_KILL. This patch is to retry for 0x068b02 Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com> Acked-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi dh alua: handle report luns data changed in check sense calloutIlgu Hong2009-03-12
| | | | | | | | | | When we switch controllers the Intel Multi-Flex reports REPORTED_LUNS_DATA_HAS_CHANGED. This patch just has us retry the command. Signed-off-by: Ilgu Hong <ilgu.hong@promise.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi dh alua: add intel Multi-Flex deviceIlgu Hong2009-03-12
| | | | | | | | | This adds the Intel Multi-Flex device to scsi_dh_alua's scsi_dh_devlist, so the module attaches to these devs. Signed-off-by: Ilgu Hong <ilgu.hong@promise.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi dh alua: fix group id maskingIlgu Hong2009-03-12
| | | | | | | | | The buf[i] is a byte but we are only asking 4 bits off the group_id. This patch has us take off a byte. Signed-off-by: Ilgu Hong <ilgu.hong@promise.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh_rdac: Add LSI vendor and product ids in rdac device listBabu Moger2008-12-29
| | | | | | [jejb: fixed whitespace damage] Signed-off-by: Babu Moger <Babu.Moger@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: Retry mode select in rdac device handlerChandra Seetharaman2008-12-29
| | | | | | | | | When the mode select sent to the controller fails with the retryable error, it is better to retry the mode_select from the hardware handler itself, instead of propagating the failure to dm-multipath. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: Make sure the state of a path is set properly when ↵Chandra Seetharaman2008-12-29
| | | | | | | | | | | controller is swapped from passive to active When the controller ownership is changed (from passive to active), check_ownership() doesn't set the state of the device to ACTIVE. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Reported-by: "Moger, Babu" <Babu.Moger@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* Commands needing to be retried require a complete re-initialization.Alan D. Brunelle2008-12-12
| | | | | | | | | | | | | The test-unit-ready portion of this patch was causing boots to fail on my test machine (as in http://lkml.org/lkml/2008/12/5/161). With this patch in place, the system is booting reliably. Mike Anderson found the same problem in the hp_hw_start_stop code, and I applied the same solution in cdrom_read_cdda_bpc. Signed-off-by: Alan D. Brunelle <alan.brunelle@hp.com> Cc: Mike Anderson <andmike@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* [SCSI] scsi_dh: Initialize path state to be passive when path is not ownedChandra Seetharaman2008-10-23
| | | | | | | | | | | Set the path state to be passive when we learn that the controller does not own the path to the LUN. This will avoid sending even a single i/o thru the passive path at the probe time. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh_alua: remove REQ_NOMERGEMike Christie2008-10-13
| | | | | | | | | We do not need to set REQ_NOMERGE because when the module calls blk_execute_rq -> blk_execute_rq_nowait, blk_execute_rq_nowait sets it for us. This brings all the modules in sync for those bits. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] block: separate failfast into multiple bits.Mike Christie2008-10-13
| | | | | | | | | | | | | | | | | | | | | | Multipath is best at handling transport errors. If it gets a device error then there is not much the multipath layer can do. It will just access the same device but from a different path. This patch breaks up failfast into device, transport and driver errors. The multipath layers (md and dm mutlipath) only ask the lower levels to fast fail transport errors. The user of failfast, read ahead, will ask to fast fail on all errors. Note that blk_noretry_request will return true if any failfast bit is set. This allows drivers that do not support the multipath failfast bits to continue to fail on any failfast error like before. Drivers like scsi that are able to fail fast specific errors can check for the specific fail fast type. In the next patch I will convert scsi. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: suppress comparison warningJames Bottomley2008-10-03
| | | | | | | | | | | | | | | | | On Mon, 2008-09-22 at 14:56 -0700, akpm@linux-foundation.org wrote: > From: Andrew Morton <akpm@linux-foundation.org> > > s390: > > drivers/scsi/device_handler/scsi_dh_emc.c: In function 'parse_sp_info_reply': > drivers/scsi/device_handler/scsi_dh_emc.c:179: warning: comparison is always false due to limited range of data type > > because chars are unsigned, I assume. Fix by making csdev->buffer explicitly an unsigned char and dropping the < 0 test. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: add Dell product information into rdac device handlerYanqing_Liu@Dell.com2008-10-03
| | | | | | | | Add Dell Powervault storage arrays into device list of rdac device handler. Signed-off-by: Yanqing Liu <yanqing_liu@dell.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: no need to initialize rq->cmd with blk_get_requestFUJITA Tomonori2008-10-03
| | | | | | | | | blk_get_request initializes rq->cmd (rq_init does) so the users don't need to do that. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: make check_sense return ADD_TO_MLQUEUEMike Anderson2008-08-29
| | | | | | | | | | Change scsi_dh check_sense functions to return ADD_TO_MLQUEUE to allow retries to occur without restriction of blk_noretry_request check. Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com> Acked-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds2008-08-20
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (22 commits) [SCSI] ibmvfc: Driver version 1.0.2 [SCSI] ibmvfc: Add details to async event log [SCSI] ibmvfc: Sanitize response lengths [SCSI] ibmvfc: Fix for lost async events [SCSI] ibmvfc: Fixup host state during reinit [SCSI] ibmvfc: Fix another hang on module removal [SCSI] ibmvscsi: Fixup desired DMA value for shared memory partitions [SCSI] megaraid_sas: remove sysfs dbg_lvl world writeable permissions [SCSI] qla2xxx: Update version number to 8.02.01-k7. [SCSI] qla2xxx: Explicitly tear-down vports during PCI remove_one(). [SCSI] qla2xxx: Reference proper ha during SBR handling. [SCSI] qla2xxx: Set npiv_supported flag for FCoE HBAs. [SCSI] qla2xxx: Don't leak SG-DMA mappings while aborting commands. [SCSI] qla2xxx: Correct vport-state management issues during ISP-ABORT. [SCSI] qla2xxx: Correct synchronization of software/firmware fcport states. [SCSI] scsi_dh: Initialize lun_state in check_ownership() [SCSI] scsi_dh: Do not use scsilun in rdac hardware handler [SCSI] megaraid_sas: version and Documentation Update [SCSI] megaraid_sas: add new controllers (0x78 0x79) [SCSI] megaraid_sas: add the shutdown DCMD cmd to driver shutdown routine ...
| * [SCSI] scsi_dh: Initialize lun_state in check_ownership()Chandra Seetharaman2008-08-16
| | | | | | | | | | | | | | lun_state need to be initialized inside check_ownership(). Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
| * [SCSI] scsi_dh: Do not use scsilun in rdac hardware handlerChandra Seetharaman2008-08-16
| | | | | | | | | | | | | | | | RDAC storage controller doesn't seem to use the scsilun format. It uses only the last byte for LUN. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* | make struct scsi_dh_devlist's staticAdrian Bunk2008-08-11
|/ | | | | | | | | This patch makes several needlessly global struct scsi_dh_devlist's static. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [SCSI] replace __FUNCTION__ with __func__Harvey Harrison2008-07-27
| | | | | | | | | | | | [jejb: fixed up a ton of missed conversions. All of you are on notice this has happened, driver trees will now need to be rebased] Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: SCSI List <linux-scsi@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: create lookup cacheHannes Reinecke2008-07-26
| | | | | | | | | | Create a cache of devices that are seen in a system. This will avoid the unnecessary traversal of the device list in the scsi_dh when there are multiple luns of a same type. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: attach to hardware handler from dm-mpathHannes Reinecke2008-07-26
| | | | | | | | | | | | | multipath keeps a separate device table which may be more current than the built-in one. So we should make sure to always call ->attach whenever a multipath map with hardware handler is instantiated. And we should call ->detach on removal, too. [sekharan: update as per comments from agk] Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: add generic SPC-3 alua handlerHannes Reinecke2008-07-26
| | | | | | Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: Update RDAC device handlerHannes Reinecke2008-07-26
| | | | | | | | | | This patch updates the RDAC device handler to refuse to attach to devices not supporting the RDAC vpd pages. Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: Update hp_sw hardware handlerHannes Reinecke2008-07-26
| | | | | | | | | | This patch updates the hp_sw device handler to properly check the return codes etc. And adds the 'correct' machine definitions. Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: Update EMC handlerHannes Reinecke2008-07-26
| | | | | | | | | | | | | | This patch converts the EMC device handler to use a proper state machine. We now also parse the extended INQUIRY information to determine if long trespass commands are supported. And we're now using the long trespass command correctly. And finally there's now an check at init time to refuse to attach to devices not supporting EMC-specific VPD pages. Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: Add 'dh_state' sysfs attributeHannes Reinecke2008-07-26
| | | | | | | | | | | | | | | | | Implement a 'dh_state' sdev attribute for dynamic device handler manipulation. A read on the attribute will return the name of the currently attached device handler or 'detached' if no handler is attached. The attribute allows the following strings to be written: - The name of the device handler to be attached if the state is 'detached'. - 'activate' to trigger path activation if a device handler is attached. - 'detach' to detach the currently attached device handler. Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: Implement common device table handlingHannes Reinecke2008-07-26
| | | | | | | | | | | | | Instead of having each and every driver implement its own device table scanning code we should rather implement a common routine and scan the device tables there. This allows us also to implement a general notifier chain callback for all device handler instead for one per handler. [sekharan: Fix rejections caused by conflicting bug fix] Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* scsi_dh: Verify "dev" is a sdev before accessing it.Chandra Seetharaman2008-07-16
| | | | | | | | | | | Before accessing the device data structure in hardware handlers, make sure it is a indeed a sdev device. Yinghai Lu <yhlu.kernel@gmail.com> found the bug on Jul 16, 2008, and later tested/verified the following fix. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* [SCSI] scsi_dh: add EMC Clariion device handlerChandra Seetharaman2008-06-05
| | | | | | | | | This adds support for EMC Clariions. This patch has the features that currently exists in mainline and advanced features from Ed's patches. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: add hp sw device handlerMike Christie2008-06-05
| | | | | | | | | This patch provides the device handler to support the older hp boxes which cannot be upgraded. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: add lsi rdac device handlerChandra Seetharaman2008-06-05
| | | | | | | | This patch provides the device handler to support the LSI RDAC SCSI based storage devices. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* [SCSI] scsi_dh: add infrastructure for SCSI Device HandlersChandra Seetharaman2008-06-05
Some of the storage devices (that can be accessed through multiple paths), do need some special handling for 1. Activating the passive path of the storage access. 2. Decode and handle the special sense codes returned by the devices. 3. Handle the I/Os being sent to the passive path, especially during the device probe time. when accessed through multiple paths. As of today this special device handling is done at the dm-multipath layer using dm-handlers. That works well for (1); for (2) to be handled at dm layer, scsi sense information need to be exported from SCSI to dm-layer, which is not very attractive; (3) cannot be done at all at the dm layer. Device handler has been moved to SCSI mainly to handle (2) and (3) properly. Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com> Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-16 12:13:09 -0500