aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/wl12xx/boot.c
Commit message (Collapse)AuthorAge
* wl12xx: AP mode - support FW TX inactivity triggersArik Nemtsov2011-07-05
| | | | | | | | | In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events. Both are reported to the upper layers as a TX failure in the offending stations. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: Support routing FW logs to the hostIdo Yariv2011-06-27
| | | | | | | | | | | | | | | | | | | | | | A recently added feature to the firmware enables the driver to retrieve firmware logs via the host bus (SDIO or SPI). There are two modes of operation: 1. On-demand: The FW collects its log in an internal ring buffer. This buffer can later be read, for example, upon recovery. 2. Continuous: The FW pushes the FW logs as special packets in the RX path. Reading the internal ring buffer does not involve the FW. Thus, as long as the HW is not in ELP, it should be possible to read the logs, even if the FW crashes. A sysfs binary file named "fwlog" was added to support this feature, letting a monitor process read the FW messages. The log is transferred from the FW only when available, so the reading process might block. Signed-off-by: Ido Yariv <ido@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: Check for FW quirks as soon as the FW bootsIdo Yariv2011-06-27
| | | | | | | | The FW initialization might depend on the FW revision, so check for any FW quirks right after booting it. Signed-off-by: Ido Yariv <ido@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: Add Support for Low Power DRPw (LPD) ModeShahar Levi2011-06-27
| | | | | | | | | | | The Low Power DRPw (LPD) mode contains several optimizations that designed to reduce power consumption. The purpose is to save current consumption in RX and Listen mode. LPD setting apply only for wl127x AP mode (not wl128x) Signed-off-by: Shahar Levi <shahar_levi@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: Stop BA session event from deviceShahar Levi2011-06-07
| | | | | | | | Adding new event that close RX BA session in case of periodic BT activity limiting WLAN activity. Signed-off-by: Shahar Levi <shahar_levi@ti.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl12xx: listen to scheduled scan eventsLuciano Coelho2011-05-12
| | | | | | | | Subscribe and listen to PERIODIC_SCAN_REPORT_EVENT_ID and PERIODIC_SCAN_COMPLETE_EVENT_ID in preparation for the scheduled scan implementation. Signed-off-by: Luciano Coelho <coelho@ti.com>
* Revert "wl12xx: support FW TX inactivity triggers"Luciano Coelho2011-05-02
| | | | | | | | | This reverts commit 47684808fd89d6809c0886e06f8ac324252499d8. Conflicts: drivers/net/wireless/wl12xx/conf.h drivers/net/wireless/wl12xx/main.c
* wl12xx: support FW TX inactivity triggersArik Nemtsov2011-04-28
| | | | | | | | | | | | | | | | | | | In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events. Both are reported to the upper layers as a TX failure in the offending stations. In STA mode we register only for the MAX_TX_RETRY event. A TX failure is interpreted as a loss of connection. Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid the inherent race condition of a mac80211 TX failure counter in addition to the FW counter. This patch depends on "mac80211: allow low level driver to report packet loss" Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl12xx: move hardcoded hci_io_ds value into the conf structLuciano Coelho2011-04-19
| | | | | | | | | Instead of hardcoding the hci_io_ds configuration that we write to the SDIO_IO_DS top registed, read it from the default configuration so that it's easier to change for different platforms. Reported-by: Ido Yariv <ido@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: Clean up and fix the 128x boot sequenceIdo Yariv2011-04-19
| | | | | | | | | | | | | | Clean up the boot sequence code & fix the following issues: 1. Always read the registers' values and set the relevant bits instead of zeroing all other bits 2. Handle cases where wl1271_top_reg_read returns an error 3. Verify that the HW can detect the selected clock source 4. Remove 128x PG10 initialization code 5. Configure the MCS PLL to work in HP mode Signed-off-by: Ido Yariv <ido@wizery.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: 1281/1283 support - Add dummy packet supportShahar Levi2011-04-19
| | | | | | | | | | | | | | | | | | Support sending dummy packet to wl128x FW as results of dummy packet event. That is part of dynamic TX mem blocks mechanism. Only send dummy packet when not in AP mode. [Even though the DUMMY_PACKET_EVENT_ID and the STA_REMOVE_COMPLETE_EVENT_ID events are defined to the same value, we need to treat them separately in the code. Keep the check and enable STA_REMOVE_COMPLETE_EVENT_ID for AP mode and DUMMY_PACKET_EVENT_ID for STA. Moved one warning to a cleaner place. Use WL1271_TID_MGMT for dummy packets -- Luca] Signed-off-by: Shahar Levi <shahar_levi@ti.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: 1281/1283 support - New boot sequenceShahar Levi2011-04-19
| | | | | | | | | | | | | | | | | | Boot sequence support FREF clock and TCXO clock. WL128x has two clocks input - TCXO and FREF. TCXO is the main clock of the device, while FREF is used to sync between the GPS and the cellular modem. Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that case the FREF will be used as the WLAN/BT main clock. [Use clock enumeration as defined in linux/wl12xx.h; remove unnecessary else block in wl128x_switch_fref; remove unnecessary change in main.c; remove some unnecessary debug prints and comments; fix potential use of uninitialized value (pll_config) -- Luca] Signed-off-by: Shahar Levi <shahar_levi@ti.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: 1281/1283 support - Loading FW & NVSShahar Levi2011-04-19
| | | | | | | | | | | | | | | | Take care of FW & NVS with the auto-detection between wl127x and wl128x. [Moved some common code outside if statements and added notes about NVS structure assumptions; Fixed a bug when checking the nvs size: if the size was incorrect, the local nvs variable was set to NULL, it should be wl->nvs instead. -- Luca] [Merged with potential buffer overflow fix -- Luca] Signed-off-by: Shahar Levi <shahar_levi@ti.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: 1281/1283 support - move IRQ polarityShahar Levi2011-04-19
| | | | | | | | | In order to prevent overran of IRQ polarity via FW the polarity setting move after FW download and before IRQ enable. Signed-off-by: Shahar Levi <shahar_levi@ti.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: Do end-of-transactions transfers only if neededIdo Yariv2011-03-03
| | | | | | | | | | | | | | | | | | | On newer hardware revisions, there is no need to write the host's counter at the end of a RX transaction. The same applies to writing the number of packets at the end of a TX transaction. It is generally a good idea to avoid unnecessary SDIO/SPI transfers. Throughput and CPU usage are improved when avoiding these. Send the host's RX counter and the TX packet count only if needed, based on the hardware revision. [Changed WL12XX_QUIRK_END_OF_TRANSACTION to use BIT(0) -- Luca] Signed-off-by: Ido Yariv <ido@wizery.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: BA initiator supportLevi, Shahar2011-01-24
| | | | | | | | | | Add 80211n BA initiator session support wl1271 driver. Include BA supported FW version auto detection mechanism. BA initiator session management included in FW independently. Signed-off-by: Shahar Levi <shahar_levi@ti.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: Enable AP-modeArik Nemtsov2011-01-24
| | | | | | | | | | | Indicate support for the NL80211_IFTYPE_AP interface mode to enable AP mode operation. Disable 11a when operating in AP-mode (unsupported for now). Signed-off-by: Arik Nemtsov <arik@wizery.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: AP specific RX filter configurationArik Nemtsov2011-01-24
| | | | | | | | Set filters according to the mode of operation. Signed-off-by: Arik Nemtsov <arik@wizery.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: AP mode - add AP specific eventArik Nemtsov2011-01-24
| | | | | | | | | | Add STA-remove completion event. Unmask it during boot if operating in AP-mode. Ignore unrelated events in AP-mode. Signed-off-by: Arik Nemtsov <arik@wizery.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
* wl12xx: remove unnecessary importHauke Mehrtens2010-12-22
| | | | | | | | No function declared in gpio.h is used here. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1271: Add wl1271_load_firmware() and export some functionsRoger Quadros2010-12-02
| | | | | | | | | | For the SDIO testing module we need to load the firmware but not boot it. wl1271_load_firmware() is meant to do just the firmware loading part. We also export some functions so they are usable in the testing module. Signed-off-by: Roger Quadros <roger.quadros@nokia.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
* wl1271: Change wl12xx Files NamesShahar Levi2010-11-22
| | | | | | | | | All files name prefix removed due to the fact that wl12xx driver supports wl1271 and wl1273. Also the definition in Kconfig and header files changed respectively. Signed-off-by: Shahar Levi <shahar_levi@ti.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
* wl1251: add wl1251 prefix to all 1251 filesKalle Valo2009-07-10
| | | | | | | | | Now that all 1271 files are split, we can add wl1251_ prefix to the files. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl12xx: moved firmware version reading routine to chip-specific functionsLuciano Coelho2009-07-10
| | | | | | | | | | | With WL1271, the firmware version can only be read right after booting the chip. To keep WL1251 aligned with this procedure, the code that reads the firmware version initially has been moved to a common place where it can be read from both chipsets. Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl12xx: add driverKalle Valo2009-05-06
wl12xx is a driver for TI wl1251 802.11 chipset designed for embedded devices, supporting both SDIO and SPI busses. Currently the driver supports only SPI. Adding support 1253 (the 5 GHz version) should be relatively easy. More information here: http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?contentId=4711&navigationId=12494&templateId=6123 (Collapsed original sequence of pre-merge patches into single commit for initial merge. -- JWL) Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-07-29 16:00:04 -0400