aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/wil6210
Commit message (Collapse)AuthorAge
* wil6210: add HW write-back option in TX descriptorKirshenbaum Erez2013-06-24
| | | | | | | | | | | Map BIT 9 in TX DMA DWARD 0 as HW write back option. We must turn on this option in the last TX descriptor, this is required for old HW compatability. This option indicate to HW that WB is required for this descriptor. Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: set vring index for all descriptorsKirshenbaum Erez2013-06-24
| | | | | | | | | | | | | The vring index (MAC queue id) must be set in all TX descriptors otherwise HW will fail to release descriptors for a specific vring (disconnect or vring switch flows). This is normally occurs when fragmentation required, if vring index will not be the same for all SKB descriptors HW will fail to flush this MAC queue. Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: Fix AP/PCP start flowKirshenbaum Erez2013-06-12
| | | | | | | | | | | | | | | | WMI PCP Start flow should not be handled through: net_device_ops->ndo_open()->wil_up()->__wil_up() because it missing mandatory FW parameters (SSID,Channel,IEs, Security...). Prior to AP starting __wil_up() may be called with iftype set cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION) depend on the application hostapd/wpa_supplicant/iw. there should not be an attempt to start an AP flow, AP/PCP start flow will be started latter by cfg80211_ops->start_ap(). Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: fix name of tracing config optionHauke Mehrtens2013-06-12
| | | | | | | | | | Tracing in wil6210 is activated with WIL6210_TRACING and not with ATH6KL_TRACING, this is used for the ath6kl driver. Rename the config option. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: Init Rx vring right after resetVladimir Kondratiev2013-06-12
| | | | | | | | | at the vring initialisation, memory pool get allocated in the FW. Make it 1-st because FW need this memory pool to precess next commands Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: Send EAPOL frames using normal Tx queueVladimir Kondratiev2013-06-12
| | | | | | | | | | | No more need for special processing of EAPOL, FW can now send EAPOL frames using normal Tx queue for TID 0 This fixes "schedule while atomic" bug - start_xmit called in softirq context; while WMI mechanism that was used may sleep. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: Derive IE's for APVladimir Kondratiev2013-06-12
| | | | | | | | When starting secure AP, in some cases wpa_s provides probe template but not probe/assoc IE's. In this case, derive missing IE's from probe. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: improve frame type reportingVladimir Kondratiev2013-06-12
| | | | | | | | | Report FC from the frame itself, as auxiliary information includes only frame subtype. This is preparation for future changes, when DMG beacon (extension frame) may be reported through wmi_evt_rx_mgmt() Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: map more FW memoryVladimir Kondratiev2013-06-12
| | | | | | | map card's back-door debug data Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: fix timeout for start_pcpVladimir Kondratiev2013-06-12
| | | | | | | | It may take up to 3500ms for the FW to start AP/PCP. Increase accordingly, adding some safety margin. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: Don't use wdev->sme_stateVladimir Kondratiev2013-05-29
| | | | | | | | sme_state is private wdev's variable. Track connection state internally Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: channel off by 1Vladimir Kondratiev2013-05-29
| | | | | | | WMI commands wants channel index, that is channel - 1 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: use kfree_skb() instead of kfree()Wei Yongjun2013-05-24
| | | | | | | | | | Use kfree_skb() instead of kfree() to free sk_buff. Introduced by commit e270045b569cc7030abd29857f3a4e7906524ec0 (wil6210: Sanity check for reported DMA length) Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: do not stop Tx queue on packet dropVladimir Kondratiev2013-05-22
| | | | | | | | | Packet drop may be caused by various flows, like disconnect while Tx packets was queued; this should not lead to stopping of the Tx queue, or all Tx get stalled. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: fix remaining use of non-cached copy of tx/rx descriptorsVladimir Kondratiev2013-05-22
| | | | | | | | | | - Introduce common code for Tx/Rx descriptor physical address set/parse - Fix endianness for address fields - consistent descriptor naming: '_d' for non-cached memory, 'd' for cached copy - wil_tx_desc_map now modify cached copy, no need for 'volatile' Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: use NAPIVladimir Kondratiev2013-05-22
| | | | | | | | | | | | | | | | | Introduce NAPI for Rx and Tx completion. This fixes packet reordering that happens when Rx handled right in the IRQ: netif_rx puts packet in 'percpu' queue, then network stack fetches packets from 'percpu' queues for processing, with different pattern of queue switching. As result, network stack see packets in different order. This causes hard to understand TCP throughput degradation in about 30min Complete polling if only one packet was processed - this eliminates empty polls that would be otherwise done at the end of each burst Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: trace supportVladimir Kondratiev2013-05-22
| | | | | | | | | | | Trace the following: - WMI cmd/event - log events - interrupts - Tx/Rx Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: debug dump packet content right after DMAVladimir Kondratiev2013-05-22
| | | | | | | | Move packet dump to the earliest location where it is known to have valid data. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: Sanity check for reported DMA lengthVladimir Kondratiev2013-05-22
| | | | | | | | | | | If Rx descriptor contains garbage, it is possible to access memory beyond allocated buffer. Check this condition and drop Rx if reported length is unreasonable large Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wil6210: 'length' in Tx/Rx descriptors is little endianVladimir Kondratiev2013-05-22
| | | | | | | | Hardware uses little endian for the Tx/Rx descriptors field 'length', do appropriate conversions Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge branch 'for-linus' of ↵Linus Torvalds2013-05-01
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull VFS updates from Al Viro, Misc cleanups all over the place, mainly wrt /proc interfaces (switch create_proc_entry to proc_create(), get rid of the deprecated create_proc_read_entry() in favor of using proc_create_data() and seq_file etc). 7kloc removed. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits) don't bother with deferred freeing of fdtables proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h proc: Make the PROC_I() and PDE() macros internal to procfs proc: Supply a function to remove a proc entry by PDE take cgroup_open() and cpuset_open() to fs/proc/base.c ppc: Clean up scanlog ppc: Clean up rtas_flash driver somewhat hostap: proc: Use remove_proc_subtree() drm: proc: Use remove_proc_subtree() drm: proc: Use minor->index to label things, not PDE->name drm: Constify drm_proc_list[] zoran: Don't print proc_dir_entry data in debug reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show() proc: Supply an accessor for getting the data from a PDE's parent airo: Use remove_proc_subtree() rtl8192u: Don't need to save device proc dir PDE rtl8187se: Use a dir under /proc/net/r8180/ proc: Add proc_mkdir_data() proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h} proc: Move PDE_NET() to fs/proc/proc_net.c ...
| * mode_t, whack-a-mole at 11...Al Viro2013-04-09
| | | | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* | Merge branch 'master' of ↵John W. Linville2013-04-24
|\ \ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
| * | wil6210: more Rx descriptor accessor functionsVladimir Kondratiev2013-04-22
| | | | | | | | | | | | | | | | | | | | | Helpers to fetch various fields from the Rx descriptor Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: Use cached copy of Tx descriptorVladimir Kondratiev2013-04-22
| | | | | | | | | | | | | | | | | | | | | | | | Original Tx descriptor stored is in non-cached area for DMA; copy it to the cached memory to speed-up access Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: Tx init optimizationVladimir Kondratiev2013-04-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | vring size is known from the beginning, fill it immediately in the struct initializer This is minor optimization that reduces code size. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: Use cached copy of Rx descriptorVladimir Kondratiev2013-04-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rx descriptors stored in non-cacheable memory area for DMA. Non-cacheable memory causes long access time from CPU. Copy rx descriptor to the skb->cb, and use this copy. It provides faster memory access, and will be usefull to keep Rx information for later processing (BACK reorder) Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | Merge branch 'master' of ↵John W. Linville2013-03-20
|\| | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
| * | wil6210: temperature measurementVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Firmware got support for temperature measurement. There are 2 temperature sensors: MAC and radio "not available" temperature - reported by FW as 0 or ~0 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: sync with new firmwareVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adjust driver for changes in the FW API. Noticeable changes in the FW are: - temperature sensing - infrastructure for multiple connections - infrastructure for P2P - signal strength indication This commit introduces only changes that are required to support same functionality as previous firmware, no new features. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: new SW resetVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | New firmware allows for shorter SW reset procedure. After SW reset, FW raises "fw done" IRQ, at this moment mailbox control structures are initialized, driver caches it. New status bit wil_status_reset_done introduced to track completion of the reset. It is set by "fw ready" irq, and required for WMI rx flow to access control structures. WMI Tx flow protected by other status bit, wil_status_fwready. It can't be set before wil_status_reset_done is set by design. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: headers clean-upVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: use WLAN_CAPABILITY_DMG_TYPE_MASKVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: fix FW error notificationVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | user space get notified through kobject_uevent_env(), that might sleep and thus should run in thread context. Move user space notification to the thread handler, while mark FW is non-functional right in the hard IRQ. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: report all received mgmt framesVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | Pass to cfg80211 all management frames. Used by wpa_supplicant. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: use cfg80211_inform_bss_frame()Vladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | Avoid unnecessary frame parsing Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: refactor connect_workerVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | Move wmi_connect_worker() to the main.c and change names for consistency. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: Fix garbage sent to the FW with wmi_set_ie()Vladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | Extra reference was taken by mistake. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: do not set IE's for beaconVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | On the DMG band, there is no 'normal' beacon frame. Instead, transmitted is short 'DMG beacon' frame, that do not include IE's So, beacon IE's are not relevant for the DMG band. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: handle WMI_BA_STATUS_EVENTIDVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | Firmware indicated block ack agreement status change. For now, just log it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: handle linkup/linkdown WMI eventsVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | Firmware indicates linkup/linkdown when data path becomes ready. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: Remove local implementation of dynamic hexdumpVladimir Kondratiev2013-03-13
| | | | | | | | | | | | | | | | | | | | | This functionality now integrated in kernel, local hack not needed any more Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: remove unused including <linux/version.h>Wei Yongjun2013-03-13
| | | | | | | | | | | | | | | | | | | | | | | | Remove including <linux/version.h> that don't need it. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | drivers/net/wireless/ath/wil6210: Makefile, only -Werror when no -W* in ↵Chen Gang2013-03-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EXTRA_CFLAGS When make with EXTRA_CFLAGS=-W, it will report error. so give a check in Makefile. Signed-off-by: Chen Gang <gang.chen@asianux.com> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wil6210: convert to use simple_open()Wei Yongjun2013-03-06
| |/ | | | | | | | | | | | | | | | | | | This removes an open coded simple_open() function and replaces file operations references to the function with simple_open() instead. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* / drivers:net: Remove dma_alloc_coherent OOM messagesJoe Perches2013-03-15
|/ | | | | | | | | | | | | | | | | I believe these error messages are already logged on allocation failure by warn_alloc_failed and so get a dump_stack on OOM. Remove the unnecessary additional error logging. Around these deletions: o Alignment neatening. o Remove unnecessary casts of dma_alloc_coherent. o Hoist assigns from ifs. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'driver-core-3.9-rc1' of ↵Linus Torvalds2013-02-21
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core patches from Greg Kroah-Hartman: "Here is the big driver core merge for 3.9-rc1 There are two major series here, both of which touch lots of drivers all over the kernel, and will cause you some merge conflicts: - add a new function called devm_ioremap_resource() to properly be able to check return values. - remove CONFIG_EXPERIMENTAL Other than those patches, there's not much here, some minor fixes and updates" Fix up trivial conflicts * tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits) base: memory: fix soft/hard_offline_page permissions drivercore: Fix ordering between deferred_probe and exiting initcalls backlight: fix class_find_device() arguments TTY: mark tty_get_device call with the proper const values driver-core: constify data for class_find_device() firmware: Ignore abort check when no user-helper is used firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER firmware: Make user-mode helper optional firmware: Refactoring for splitting user-mode helper code Driver core: treat unregistered bus_types as having no devices watchdog: Convert to devm_ioremap_resource() thermal: Convert to devm_ioremap_resource() spi: Convert to devm_ioremap_resource() power: Convert to devm_ioremap_resource() mtd: Convert to devm_ioremap_resource() mmc: Convert to devm_ioremap_resource() mfd: Convert to devm_ioremap_resource() media: Convert to devm_ioremap_resource() iommu: Convert to devm_ioremap_resource() drm: Convert to devm_ioremap_resource() ...
| * wireless: remove conflicting version of print_hex_dump_bytesStephen Rothwell2013-01-17
| | | | | | | | | | | | | | | | This fixes the build due to there now being two copies of print_hex_dump_bytes in the tree. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | Merge branch 'master' of ↵John W. Linville2013-02-18
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/iwlwifi/dvm/tx.c drivers/net/wireless/ti/wlcore/sdio.c drivers/net/wireless/ti/wlcore/spi.c
| * | cfg80211: pass wiphy to cfg80211_ref_bss/put_bssJohannes Berg2013-02-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | This prepares for using the spinlock instead of krefs which is needed in the next patch to track the refs of combined BSSes correctly. Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-08-07 07:53:50 -0400