aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/tg3.c
Commit message (Collapse)AuthorAge
* [TG3]: Speed up SRAM access (2nd version)Michael Chan2006-04-10
| | | | | | | | | | | | | | | | | | | | | | | | Speed up SRAM read and write functions if possible by using MMIO instead of config. cycles. With this change, the post reset signature done at the end of D3 power change must now be moved before the D3 power change. IBM reported a problem on powerpc blades during ethtool self test that was caused by the memory test taking excessively long. Config. cycles are very slow on powerpc and the memory test can take more than 10 seconds to complete using config. cycles. David Miller informed me that an earlier version of the patch caused problems on sparc64 systems with built-in tg3 chips. This version fixes the problem by excluding all SUN built-in tg3 chips from doing MMIO SRAM access. TG3_FLAG_EEPROM_WRITE_PROT is also set unconditionally when TG3_FLG2_SUN_570X is set. This should be sane as all SUN chips are built-in and do not require Vaux switching. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Kill some less useful flagsMichael Chan2006-04-10
| | | | | | | | Kill the TG3_FLAG_NO_{TX|RX}_PSEUDO_CSUM flags because they are not very useful. This will free up some bits for new flags. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix a memory leak.Adrian Bunk2006-04-10
| | | | | | | | This patch fixes a memory leak (buf wasn't freed) spotted by the Coverity checker. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivialLinus Torvalds2006-04-02
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits) Documentation: fix minor kernel-doc warnings BUG_ON() Conversion in drivers/net/ BUG_ON() Conversion in drivers/s390/net/lcs.c BUG_ON() Conversion in mm/slab.c BUG_ON() Conversion in mm/highmem.c BUG_ON() Conversion in kernel/signal.c BUG_ON() Conversion in kernel/signal.c BUG_ON() Conversion in kernel/ptrace.c BUG_ON() Conversion in ipc/shm.c BUG_ON() Conversion in fs/freevxfs/ BUG_ON() Conversion in fs/udf/ BUG_ON() Conversion in fs/sysv/ BUG_ON() Conversion in fs/inode.c BUG_ON() Conversion in fs/fcntl.c BUG_ON() Conversion in fs/dquot.c BUG_ON() Conversion in md/raid10.c BUG_ON() Conversion in md/raid6main.c BUG_ON() Conversion in md/raid5.c Fix minor documentation typo BFP->BPF in Documentation/networking/tuntap.txt ...
| * BUG_ON() Conversion in drivers/net/Eric Sesterhenn2006-04-02
| | | | | | | | | | | | | | | | this changes if() BUG(); constructs to BUG_ON() which is cleaner, contains unlikely() and can better optimized away. Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
* | [TG3]: Update driver version and reldate.David S. Miller2006-04-01
| | | | | | | | Signed-off-by: David S. Miller <davem@davemloft.net>
* | [TG3]: Revert "Speed up SRAM access"David S. Miller2006-04-01
|/ | | | | | | | | | | Undo commit 100c4673307f5806788791b9b886877c806afd96 MMIOs timeout more quickly that PCI config cycles and some of these SRAM accesses can take a very long time, triggering the MMIO limits on some sparc64 PCI controllers and thus resulting in bus timeouts and bus errors. Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update version and reldateMichael Chan2006-03-28
| | | | | | | Update version to 3.55. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Skip timer code during full lockMichael Chan2006-03-28
| | | | | | | | Skip the main timer code if interrupts are disabled in the full lock state. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Speed up SRAM accessMichael Chan2006-03-28
| | | | | | | | | | | | | | | | | Speed up SRAM read and write functions if possible by using MMIO instead of config. cycles. With this change, the post reset signature done at the end of D3 power change must now be moved before the D3 power change. IBM reported a problem on powerpc blades during ethtool self test that was caused by the memory test taking excessively long. Config. cycles are very slow on powerpc and the memory test can take more than 10 seconds to complete using config. cycles. As a result, NETDEV WATCHDOG can be triggered during self test and the chip can end up in a funny state. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix PHY loopback on 5700Michael Chan2006-03-28
| | | | | | | Fix PHY loopback failure on some 5700 devices. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix bug in 40-bit DMA workaround codeMichael Chan2006-03-28
| | | | | | | | Need to check the TG3_FLAG_40BIT_DMA_BUG flag in the workaround code path instead of device flags. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix probe failure due to invalid MAC addressMichael Chan2006-03-28
| | | | | | | | | | | | | Some older bootcode in some devices may report 0 MAC address in SRAM when booting up from low power state. This patch fixes the problem by checking for a valid MAC address in SRAM and falling back to NVRAM if necessary. Thanks to walt <wa1ter@myrealbox.com> for reporting the problem and helping to debug it. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update driver version and reldate.David S. Miller2006-03-23
| | | | Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5755 nvram supportMichael Chan2006-03-23
| | | | | | | Add 5755 nvram support. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5755 supportMichael Chan2006-03-23
| | | | | | | Add support for new chip 5755 which is very similar to 5787. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Bump driver version and reldate.David S. Miller2006-03-22
| | | | Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Skip phy power down on some devicesMichael Chan2006-03-22
| | | | | | | | Some PHYs should not be powered down in tg3_set_power_state() because of bugs or other hardware limitations. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix SRAM access during tg3_init_one()Michael Chan2006-03-22
| | | | | | | | | | | 5700 and 5701 will not return correct SRAM data when the chip is in D3hot power state. tg3_get_eeprom_hw_cfg() must first put the device in D0 before reading SRAM. Thanks to Thomas Chenault at Dell for noticing this problem. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Don't mark tg3_test_registers() as returning const.David S. Miller2006-03-21
| | | | Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: make drivers/net/tg3.c:tg3_request_irq() staticAdrian Bunk2006-03-21
| | | | | | | | This patch makes the needlessly global function tg3_request_irq() static. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: netif_carrier_off runs too early; could still be queued when init failsJeff Mahoney2006-03-21
| | | | | | | | | | | | | | | | | | | | | | Move the netif_carrier_off() call from tg3_init_one()-> tg3_init_link_config() to tg3_open() as is the convention for most other network drivers. I was getting a panic after a tg3 device failed to initialize due to DMA failure. The oops pointed to the link watch queue with spinlock debugging enabled. Without spinlock debugging, the Oops didn't occur. I suspect that the link event was getting queued but not executed until after the DMA test had failed and the device was freed. The link event was then operating on freed memory, which could contain anything. With this patch applied, the Oops no longer occurs. [ Based upon feedback from Michael Chan, we move netif_carrier_off() to the end of tg3_init_one() instead of moving it to tg3_open() -DaveM ] Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: update version and reldateMichael Chan2006-03-21
| | | | | | | Update version to 3.52. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add firmware version infoMichael Chan2006-03-21
| | | | | | | Add fw_version information to ethtool -i. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: nvram cleanupMichael Chan2006-03-21
| | | | | | | | | | | | | Some nvram related cleanup: 1. Add a tg3_nvram_read_swab() since swabing the data is frequently done. 2. Add a function to convert nvram address to physical address instead of doing it in 2 separate places. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fixup memory test for 5787Michael Chan2006-03-21
| | | | | | | Ethtool memory test on 5787 requires a new memory table. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add new one-shot MSI handlerMichael Chan2006-03-21
| | | | | | | | | | | Support one-shot MSI on 5787. This one-shot MSI idea is credited to David Miller. In this mode, MSI disables itself automatically after it is generated, saving the driver a register access to disable it for NAPI. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add ipv6 checksum supportMichael Chan2006-03-21
| | | | | | | Support ipv6 tx csum on 5787 by setting NETIF_F_HW_CSUM. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add new hard_start_xmitMichael Chan2006-03-21
| | | | | | | | | | | | | Support 5787 hardware TSO using a new flag TG3_FLG2_HW_TSO_2. Since the TSO interface is slightly different and these chips have finally fixed the 4GB DMA problem and do not have the 40-bit DMA problem, a new hard_start_xmit is used for these chips. All previous chips will use the old hard_start_xmit that is now renamed tg3_start_xmit_dma_bug(). Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5787 nvram supportMichael Chan2006-03-21
| | | | | | | Support additional nvrams and new nvram format for 5787 and 5754. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add 5787 and 5754 basic supportMichael Chan2006-03-21
| | | | | | | Add basic support for 2 new chips 5787 and 5754. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Fix tg3_get_ringparam()Michael Chan2006-03-21
| | | | | | | | | | | | | | Fix-up tg3_get_ringparam() to return the correct parameters. Set the jumbo rx ring parameter only if it is supported by the chip and currently in use. Add missing value for tx_max_pending, noticed by Rick Jones. Update version to 3.51. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add some missing netif_running() checksMichael Chan2006-03-21
| | | | | | | | | Add missing netif_running() checks in tg3's dev->set_multicast_list() and dev->set_mac_address(). If not netif_running(), these 2 calls can simply return 0 after storing the new settings if required. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update version and reldateMichael Chan2006-03-20
| | | | | | | Update version to 3.50. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Support shutdown WoL.Michael Chan2006-03-20
| | | | | | | | | | | | | | | Support WoL during shutdown by calling tg3_set_power_state(tp, PCI_D3hot) during tg3_close(). Change the power state parameter to pci_power_t type and use constants defined in pci.h. Certain ethtool operations cannot be performed after tg3_close() because the device will go to low power state. Add return -EAGAIN in such cases where appropriate. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Enable TSO by defaultMichael Chan2006-03-20
| | | | | | | | | Enable TSO by default on newer chips that support TSO in hardware. Leave TSO off by default on older chips that do firmware TSO because performance is slightly lower. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Add support for 5714S and 5715SMichael Chan2006-03-20
| | | | | | | Add support for 5714S and 5715S. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds2006-03-20
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (230 commits) [SPARC64]: Update defconfig. [SPARC64]: Fix 2 bugs in huge page support. [SPARC64]: CONFIG_BLK_DEV_RAM fix [SPARC64]: Optimized TSB table initialization. [SPARC64]: Allow CONFIG_MEMORY_HOTPLUG to build. [SPARC64]: Use SLAB caches for TSB tables. [SPARC64]: Don't kill the page allocator when growing a TSB. [SPARC64]: Randomize mm->mmap_base when PF_RANDOMIZE is set. [SPARC64]: Increase top of 32-bit process stack. [SPARC64]: Top-down address space allocation for 32-bit tasks. [SPARC64] bbc_i2c: Fix cpu check and add missing module license. [SPARC64]: Fix and re-enable dynamic TSB sizing. [SUNSU]: Fix missing spinlock initialization. [TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts. [SPARC64]: First cut at VIS simulator for Niagara. [SPARC64]: Fix system type in /proc/cpuinfo and remove bogus OBP check. [SPARC64]: Add SMT scheduling support for Niagara. [SPARC64]: Fix 32-bit truncation which broke sparsemem. [SPARC64]: Move over to sparsemem. [SPARC64]: Fix new context version SMP handling. ...
| * [TG3]: Do not try to access NIC_SRAM_DATA_SIG on Sun parts.David S. Miller2006-03-20
| | | | | | | | | | | | | | Sun does't put an SEEPROM behind the tigon3 chip, among other things, so accesses to these areas just give bus timeouts. Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'master'Jeff Garzik2006-03-20
|\|
| * [TG3]: 40-bit DMA workaround part 2Michael Chan2006-03-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 40-bit DMA workaround recently implemented for 5714, 5715, and 5780 needs to be expanded because there may be other tg3 devices behind the EPB Express to PCIX bridge in the 5780 class device. For example, some 4-port card or mother board designs have 5704 behind the 5714. All devices behind the EPB require the 40-bit DMA workaround. Thanks to Chris Elmquist again for reporting the problem and testing the patch. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'upstream-fixes'Jeff Garzik2006-03-16
|\|
| * [TG3] tg3_bus_string(): remove dead codeAdrian Bunk2006-03-11
| | | | | | | | | | | | | | | | The Coverity checker spotted this dead code (note that (clock_ctrl == 7) is already handled above). Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'upstream-fixes'Jeff Garzik2006-03-11
|\|
| * [TG3]: Add DMA address workaroundMichael Chan2006-03-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add DMA workaround for chips that do not support full 64-bit DMA addresses. 5714, 5715, and 5780 chips only support DMA addresses less than 40 bits. On 64-bit systems with IOMMU, set the dma_mask to 40-bit so that pci_map_xxx() calls will map the DMA address below 40 bits if necessary. On 64-bit systems without IOMMU, set the dma_mask to 64-bit and check for DMA addresses exceeding the limit in tg3_start_xmit(). 5788 only supports 32-bit DMA so need to set the mask appropriately also. Thanks to Chris Elmquist at SGI for reporting and helping to debug the problem on 5714. Thanks to David Miller for explaining the HIGHMEM and DMA stuff. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Massive net driver const-ification.Arjan van de Ven2006-03-03
|/
* [TG3]: Fix Sun tg3 variant detection.David S. Miller2006-02-27
| | | | | | | | | Some Sun parts don't have PCI_VENDOR_ID_SUN in the subsystem vendor ID. So add another fallback test, which is the name of the OBP firmware device tree node. If it's a Sun part we'll get "network", else it will be named "ethernet". Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Update driver version and release date.David S. Miller2006-02-02
| | | | Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Flush tg3_reset_task()Michael Chan2006-02-02
| | | | | | | | | | | | | | Make sure tg3_reset_task() is flushed in the close and suspend paths as noted by Jeff Garzik. In the close path, calling flush_scheduled_work() may cause deadlock if linkwatch_event() is on the workqueue. linkwatch_event() will try to get the rtnl_lock() which is already held by tg3_close(). So instead, we set a flag in tg3_reset_task() and tg3_close() polls the flag until it is cleared. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* [TG3]: Refine nvram lockingMichael Chan2006-01-17
| | | | | | | | | | | | | | | Add nvram lock count so that calls to tg3_nvram_lock()/unlock() can be nested. Add error checking to all callers of tg3_nvram_lock() where appropriate. To prevent nvram lock failures after halting the firmware, it is also necessary to release firmware's nvram lock in tg3_halt_cpu(). Update version to 3.48. Based on David Miller's initial patch. Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-16 08:10:04 -0500