aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/sfc
Commit message (Collapse)AuthorAge
* sfc: SFT9001/SFN4111T: Check PHY boot status during board initialisationBen Hutchings2009-03-02
| | | | | | | | | | | During SFN4111T initialisation, check whether the PHY boot status indicates a bad firmware checksum. If so, prepare to reflash rather than continuing with normal initialisation. Remove redundant PHY boot status check from tenxpress_phy_init(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Fix test for MDIO read failureBen Hutchings2009-03-02
| | | | | | | | | | | Commit 27dd2caca4eabe7c13a052b7456495ba75535e6a changed mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and to combine their values into an unsigned 32-bit mask. This made the following test for a negative (failure) value useless. Fix it to check whether either read failed. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: SFT9001: Include non-breaking cable diagnostics in online self-testsBen Hutchings2009-03-02
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/sfc: fix sparse warnings: Should it be static?Hannes Eder2009-02-18
| | | | | | | | | | | | | | | Impact: Include the header file. If CONFIG_SFC_MTD is not defined then the functions 'efx_mtd_remove' and 'efx_mtd_rename' are defined 'static inline' with an empty function body in the header file, but the the whole file mtd.c is not built in this case. Fix this sparse warnings: drivers/net/sfc/mtd.c:204:6: warning: symbol 'efx_mtd_remove' was not declared. Should it be static? drivers/net/sfc/mtd.c:221:6: warning: symbol 'efx_mtd_rename' was not declared. Should it be static? drivers/net/sfc/mtd.c:230:5: warning: symbol 'efx_mtd_probe' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/sfc: fix sparse warning: symbol shadows an earlier oneHannes Eder2009-02-17
| | | | | | | | | | | | Impact: Move variable declaration as close to their usage as possible. Fix this sparse warning: drivers/net/sfc/tenxpress.c:589:22: warning: symbol 'link_ok' shadows an earlier one drivers/net/sfc/tenxpress.c:575:30: originally declared here Signed-off-by: Hannes Eder <hannes@hanneseder.net> Acked-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: replace uses of __constant_{endian}Harvey Harrison2009-02-01
| | | | | | | Base versions handle constant folding now. Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-01-30
|\ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e1000/e1000_main.c
| * sfc: Replace stats_enabled flag with a disable countBen Hutchings2009-01-30
| | | | | | | | | | | | | | | | | | | | | | Currently we use a spin-lock to serialise statistics fetches and also to inhibit them for short periods of time, plus a flag to enable/disable statistics fetches for longer periods of time, during online reset. This was apparently insufficient to deal with the several reasons for stats being disabled. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: SFX7101/SFT9001: Fix AN advertisementsBen Hutchings2009-01-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All 10Xpress PHYs require autonegotiation all the time; enforce this in the set_settings() method and do not treat it as a workaround. Remove claimed support for 100M HD mode since it is not supported by current firmware. Do not set speed override bits when AN is enabled, and do not use register 1.49192 for AN configuration as it can override what we set elsewhere. Always set the AN selector bits to 1 (802.3). Fix confusion between Next Page and Extended Next Page. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: SFT9001: Always enable XNP exchange on SFT9001 rev BBen Hutchings2009-01-30
| | | | | | | | | | | | | | This workaround is not specific to rev A. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: Update board info for hardware monitor on SFN4111T-R5 and laterBen Hutchings2009-01-30
| | | | | | | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: Test for PHYXS faults whenever we cannot test link state bitsSteve Hodgson2009-01-30
| | | | | | | | | | | | | | | | | | Depending on the loopback mode, there may be no pertinent link state bits. In this case we test the PHYXS RX fault bit instead. Make sure to do this in all cases where there are no link state bits. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: Reinitialise the PHY completely in case of a PHY or NIC resetSteve Hodgson2009-01-30
| | | | | | | | | | | | | | | | | | | | In particular, set pause advertising bits properly. A PHY reset is not necessary to recover from the register self-test, so use a "invisible" reset there instead. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: Fix post-reset MAC selectionSteve Hodgson2009-01-30
| | | | | | | | | | | | | | | | | | Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the MAC is the same as it was before. This ensures that the value is correct after an online reset. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1Ben Hutchings2009-01-30
| | | | | | | | | | | | | | | | | | | | | | | | | | Change sfn4111t_reset() to change only GPIO output enables so that it doesn't break subsequent I2C operations. Update comments to explain exactly what we're doing. Add a short sleep to make sure the FLASH_CFG_1 value is latched before any subsequent I2C operations. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: SFT9001: Fix speed reporting in 1G PHY loopbackSteve Hodgson2009-01-30
| | | | | | | | | | | | | | | | Instead of disabling AN in loopback, just prevent restarting AN and override the speed in sft9001_get_settings(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: SFX7101: Remove workaround for bad link trainingSteve Hodgson2009-01-30
| | | | | | | | | | | | | | | | | | | | | | | | Early versions of the SFX7101 firmware could complete link training in a state where it would not adequately cancel noise (Solarflare bug 10750). We previously worked around this by resetting the PHY after seeing many Ethernet CRC errors. This workaround is unsafe since it takes no account of the interval between errors; it also appears to be unnecessary with production firmware. Therefore remove it. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * sfc: SFT9001: Enable robust link trainingSteve Hodgson2009-01-30
| | | | | | | | | | | | | | | | Enable a firmware option that appears to be necessary for reliable operation. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: Add skb_record_rx_queue() calls to multiqueue capable drivers.David S. Miller2009-01-27
| | | | | | | | Signed-off-by: David S. Miller <davem@davemloft.net>
* | sfc: Replace LRO with GROHerbert Xu2009-01-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch makes sfc invoke the GRO hooks instead of LRO. As GRO has a compatible external interface to LRO this is a very straightforward replacement. Everything should appear identical to the user except that the offload is now controlled by the GRO ethtool option instead of LRO. I've kept the lro module parameter as is since that's for compatibility only. I have eliminated efx_rx_mk_skb as the GRO layer can take care of all packets regardless of whether GRO is enabled or not. So the only case where we don't call GRO is if the packet checksum is absent. This is to keep the behaviour changes of the patch to a minimum. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: Remove redundant NAPI functionsBen Hutchings2009-01-21
|/ | | | | | | | | | | Following the removal of the unused struct net_device * parameter from the NAPI functions named *netif_rx_* in commit 908a7a1, they are exactly equivalent to the corresponding *napi_* functions and are therefore redundant. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: SFT9001: Fix condition for LNPGA power-offBen Hutchings2009-01-11
| | | | | | | | Only the SFX7101 requires software power control. This was incorrectly being applied to the SFT9001 rev A as well. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: sfc: Use pci_clear_master() to disable bus masteringBen Hutchings2009-01-07
| | | | | | | | | | pci_disable_device() disables many features, like MSI-X, which we never reenable in efx_reset(). Further, calls to pci_enable_device() and pci_disable_device() must be matched since the nesting count was introduced, so switch to using pci_clear_master() instead. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* net: Fix warning fallout from recent NAPI interface changes.David S. Miller2008-12-26
| | | | | | | | | | | When we removed the network device argument from several NAPI interfaces in 908a7a16b852ffd618a9127be8d62432182d81b4 ("net: Remove unused netdev arg from some NAPI interfaces.") several drivers now started getting unused variable warnings. This fixes those up. Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: If AN is enabled, always read speed/duplex from the AN advertising bitsBen Hutchings2008-12-26
| | | | | | | | | When AN is enabled and the link is down the speed/duplex control bits will not be meaningful. Use the advertising bits instead, and mask them with the LPA bits if and only if AN is complete (as before). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: When disabling the NIC, close the device rather than unregistering itBen Hutchings2008-12-26
| | | | | | | | This should reduce user confusion and may also aid recovery (ioctls will still be available). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: SFT9001: Add cable diagnosticsBen Hutchings2008-12-26
| | | | | | | | | | The SFT9001 firmware implements cable diagnostics; run those and include their results in a self-test. In case of a cable fault, do not fail the self-test as a whole; only faults in the NIC should cause that. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for multiple PHY self-testsBen Hutchings2008-12-26
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Merge top-level functions for self-testsBen Hutchings2008-12-26
| | | | | | | Pass in ethtool test flags to determine which tests to run. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up PHY mode management in loopback self-testBen Hutchings2008-12-26
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Fix unreliable link detection in some loopback modesBen Hutchings2008-12-26
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Generate unique names for per-NIC workqueuesBen Hutchings2008-12-26
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Remove unused netdev arg from some NAPI interfaces.Neil Horman2008-12-22
| | | | | | | | | | When the napi api was changed to separate its 1:1 binding to the net_device struct, the netif_rx_[prep|schedule|complete] api failed to remove the now vestigual net_device structure parameter. This patch cleans up that api by properly removing it.. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Version 2.3Ben Hutchings2008-12-13
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Fix synchronisation of efx_mtd_{probe,rename,remove}Ben Hutchings2008-12-13
| | | | | | | | | | | | | Currently efx_mtd_rename() can race with the probe() and remove() functions. Move probe() before device registration and remove() after unregistration. Move initialisation/update of all names based on the netdev name into a new function and call it under the RTNL immediately after registration. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Use kzalloc() to ensure struct efx_spi_device is fully initialisedBen Hutchings2008-12-13
| | | | | | | Currently the mtd field is not initialised early enough. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Treat probe as unsuccessful if it scheduled a resetSteve Hodgson2008-12-13
| | | | | | | | | | From: Steve Hodgson <shodgson@solarflare.com> efx_pci_probe_main() can return success despite a reset being scheduled. Catch this and retry or abort probe depending on the reset type. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Use model numbers for PHY type namesBen Hutchings2008-12-13
| | | | | | | | | | Some of the PHY type names are overly generic. Change them to include the model numbers of the PHYs they represent. Correct the model number reference at the top of xfp_phy.c. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Use mutex_lock_interruptible() for ethtool EEPROM accessBen Hutchings2008-12-13
| | | | | | | | | ethtool must contend with the MTD driver for the SPI bus lock, which may carry out long operations such as flash erase. Allow it to be interrupted while waiting. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Specify a meaningful component for loopback RX-side and PHY testsBen Hutchings2008-12-13
| | | | | | | | | Our ethtool self-test result names each begin with a component name. For some results this is "port0", which is not very meaningful. Change that to "rx" or "phy" as appropriate. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Remove leading spacesBen Hutchings2008-12-13
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for SFN4111TBen Hutchings2008-12-13
| | | | | | | | Add support code for the SFN4111T 100/1000/10GBASE-T reference design, based in part on the existing code for the SFE4001. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for Solarflare 10Xpress SFT9001Ben Hutchings2008-12-13
| | | | | | | | | | | | Add type codes for the new PHY and rename the SFX7101 type code. Add definition of clause 22 extension MMD. Adapt the 10Xpress SFX7101 code to support the SFT9001 as well. Clean up register definitions. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Rework MAC, PHY and board event handlingBen Hutchings2008-12-13
| | | | | | | | | | | From: Steve Hodgson <shodgson@solarflare.com> MAC, PHY and board events may be separately enabled and signalled. Our current arrangement of chaining the polling functions can result in events being missed. Change them to be more independent. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Implement auto-negotiationBen Hutchings2008-12-13
| | | | | | | | | | | | Add infrastructure for auto-negotiation of speed, duplex and flow control. When using 10Xpress, auto-negotiate flow control. While we're at it, clean up the code to warn when partner is not 10GBASE-T capable. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for sub-10G speedsBen Hutchings2008-12-13
| | | | | | | | | | | | | The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce an efx_mac_operations structure with implementations for the two MACs. Switch between the MACs as necessary. PHY settings are independent of the MAC, so add get_settings() and set_settings() to efx_phy_operations. Also add macs field to indicate which MACs the PHY is connected to. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up MDIO flag settingBen Hutchings2008-12-13
| | | | | | | | | We often want to set or clear a flag in an MDIO register, but avoid writing if no change is required since this can have side-effects. Encapsulate this in a function, mdio_clause45_set_flag(). Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Clean up board identificationBen Hutchings2008-12-13
| | | | | | | | | Remove kluge for development boards with unspecified board type. Remove assumption of contiguous board type code assignments. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add phy_type device attributeBen Hutchings2008-12-13
| | | | | Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* sfc: Add support for MMDs numbered >15Ben Hutchings2008-12-13
| | | | | | | | Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of reading just DEVS0. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.2 (git 2.25.0) at 2025-01-14 00:43:18 -0500