aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/qlge/qlge_mpi.c
Commit message (Collapse)AuthorAge
* qlge: Fix early exit from mbox cmd complete wait.Ron Mercer2009-11-06
| | | | | | | | | This line was accidentally left out of the previous commit # da03945140a035a2962f7f93e359085596f20499 ("qlge: Fix firmware mailbox command timeout."). Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Fix firmware mailbox command timeout.Ron Mercer2009-10-29
| | | | | | | | | The mailbox command process would only process a maximum of 5 unrelated firmware events while waiting for it's command completion status. It should process an unlimited number of events while waiting for a maximum of 5 seconds. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Add disable/enable firmare irqs to handler.Ron Mercer2009-10-09
| | | | | | | | | This was accidentally omitted from one of the previous patches for firmware event handling. The handler needs to the enable firmware irq mask when it's done processing or it may not get any more events interrupts. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Fix chip reset process.Ron Mercer2009-10-09
| | | | | | | | | Add wait for NIC fifo and MGMNT fifo to empty before applying reset. Otherwise broken frames can be processed by management processor and cause it to hang. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Fix lock/mutex warnings.Ron Mercer2009-10-06
| | | | | | | | | | Get rid of spinlock and private mutex usage for exclusive access to the HW semaphore register. rtnl_lock already creates exclusive access to this register in all driver API. Add rtnl to firmware worker threads that also use the HW semaphore register. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Add/use function for link up/down.Ron Mercer2009-07-03
| | | | | | | | | | | We need to set/clear the mac address register when the link goes up/down respectively. Without this both ports of a 2-port device can end up with the same mac address in a bonding scenario. The new ql_link_on() and ql_link_off() will also be used in handling certain firmware events. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-06-15
|\ | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: Documentation/feature-removal-schedule.txt drivers/scsi/fcoe/fcoe.c net/core/drop_monitor.c net/core/net-traces.c
| * trivial: fix typos s/paramter/parameter/ and s/excute/execute/ in ↵Martin Olsson2009-06-12
| | | | | | | | | | | | | | documentation and source comments. Signed-off-by: Martin Olsson <martin@minimum.se> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* | qlge: Add support for retrieving firmware version.Ron Mercer2009-06-10
| | | | | | | | | | | | | | This is used by driver banner and ethtool info. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qlge: Fix timeout on firmware mailbox commands.Ron Mercer2009-06-08
| | | | | | | | | | | | | | | | | | | | Some firmware mailbox commands require the firmware to communicate with the FCoE driver running on another PCI function. This can potentially take several seconds. This wait is done in process context only. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qlge: Fix bug in MTU setting process.Ron Mercer2009-06-08
| | | | | | | | | | | | | | | | | | Since an FCoE function shares a port with this NIC function, the jumbo settings must always be in place. This patch causes the hardware to be set up for jumbo if it is not already done. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qlge: Fix bug in firmware event handler.Ron Mercer2009-06-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Each firmware mailbox command can have a different number of valid data elements. When waiting for a mailbox command to complete it the process passes it's element count and waits for the completion. It is possible that while waiting an unrelated firmware async event (AE) can arrive. When this happens, the handler will over write the element count with the value for the newly arrived AE. This can cause the mailbox command to not get all of it's data. This patch restores original mailbox count at the end of the handler. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | qlge: Fix firmware event handler loop.Ron Mercer2009-06-08
|/ | | | | | | | | Check status on every iteration of event handler loop and exit if an error occurred. If an error occurred then recover process will be queued so this loop should no continue. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Add support for lost firmware events.Ron Mercer2009-03-04
| | | | | | | | | | When the firmware is issuing events to the driver the events must be removed from the queue. If the queue overflows, the firmware will build and special event that captures those that are lost. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Save status from firmware crash (system err).Ron Mercer2009-03-04
| | | | | Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Improve handling for firmware init failure.Ron Mercer2009-03-04
| | | | | | | | This event will arrive at boot time or after an MPI processor reset if the firmware failed to initialize. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Clean up event handler for firmware init.Ron Mercer2009-03-04
| | | | | Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Add worker-handler for firmware events.Ron Mercer2009-03-04
| | | | | | | | | | | | | | | | This worker and it's supporting routines are used for IDC 'inter-device-communication' events that require an ACK mailbox command be sent to allow completion of the request. These requests are originated by another function wanting to change some common port paramters. Typical example would be: 1) Change max TX/RX frame size allowed. 2) Change pause parameters. 3) Change loopback mode. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Clean up link up processing.Ron Mercer2009-03-04
| | | | | Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Clean up link down processing.Ron Mercer2009-03-04
| | | | | Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Add firmware support for insert/remove SFP.Ron Mercer2009-03-04
| | | | | Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Add support for getting/setting port config.Ron Mercer2009-03-03
| | | | | | | | | | | | This patch adds functionality to get and set port parameters. Currently it is used to set maximum TX/RX frame sizes. This process is also capable of setting: 1) Pause type: Standard or Priority based. 2) Loop back mode. 3) Enable Jumbo frame mode (included here...) Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Add support for firmware mailbox commands.Ron Mercer2009-03-03
| | | | | | | | | This interface will be used for setting things like maximum frame size, setting WOL, and ACKing changes requested by the FCOE function. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Move firmware event handler.Ron Mercer2009-02-27
| | | | | | | | | | | This is not a logical change but rather a move of the inbound firmware event handler into it's own function as it will later be called by the outbound path. The addition of the mutex is to create exclusive access to the mailbox commands between inbound and outbound handling. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: Clean up firmware reset path.Ron Mercer2009-02-27
| | | | | | | | Add function for performing the reset rather than in-line. This function may later be called by a core dump process. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/qlge: fix sparse warnings: make symbols staticHannes Eder2008-12-26
| | | | | | | | | | Fix this sparse warnings: drivers/net/qlge/qlge_ethtool.c:100:6: warning: symbol 'ql_update_stats' was not declared. Should it be static? drivers/net/qlge/qlge_mpi.c:22:5: warning: symbol 'ql_get_mb_sts' was not declared. Should it be static? Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlge: New Qlogic 10Gb Ethernet Driver.Ron Mercer2008-09-18
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-27 11:41:02 -0500