aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/ethoc.c
Commit message (Collapse)AuthorAge
* net: ethoc: remove empty MDIO bus functionFlorian Fainelli2014-03-28
| | | | | | | | ethoc_mdio_reset() does nothing useful and is optional for the MDIO bus code, so let's just remove it. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethoc: set up MII management bus clockMax Filippov2014-02-04
| | | | | | | | | | | | | | MII management bus clock is derived from the MAC clock by dividing it by MIIMODER register CLKDIV field value. This value may need to be set up in case it is undefined or its default value is too high (and communication with PHY is too slow) or too low (and communication with PHY is impossible). The value of CLKDIV is not specified directly, but is derived from the MAC clock for the default MII management bus frequency of 2.5MHz. The MAC clock may be specified in the platform data, or in the 'clocks' device tree attribute. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethoc: don't advertise gigabit speed on attached PHYMax Filippov2014-02-04
| | | | | | | | | | | | | OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does not disable advertisement when PHY supports them. This results in non-functioning network when the MAC is connected to a gigabit PHY connected to a gigabit switch. The fix is to disable gigabit speed advertisement on attached PHY unconditionally. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethoc: implement ethtool get/set ring parametersMax Filippov2014-02-01
| | | | | | | | | | TX and RX rings share memory and descriptors. Maximal number of descriptors reported is one less than the total available nuber of descriptors. For the set operation the requested number of TX descriptors is rounded down to the nearest power of two (driver logic requirement). Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethoc: implement ethtool get registersMax Filippov2014-02-01
| | | | | | | Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethoc: implement ethtool get/set settingsMax Filippov2014-02-01
| | | | | | Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethoc: implement basic ethtool operationsMax Filippov2014-02-01
| | | | | | | | | | | The following methods are implemented: - get link state (standard implementation); - get timestamping info (standard implementation). Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethoc: use dev_get_platdata()Jingoo Han2013-08-30
| | | | | | | | | Use the wrapper function for retrieving the platform data instead of accessing dev->platform_data directly. This is a cosmetic change to make the code simpler and enhance the readability. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: remove unnecessary platform_set_drvdata()Jingoo Han2013-05-28
| | | | | | | | | | | | | | | | The driver core clears the driver data to NULL after device_release or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d (device-core: Ensure drvdata = NULL when no driver is bound). Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Roland Stigge <stigge@antcom.de> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Tested-by: Roland Stigge <stigge@antcom.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethoc: Cleanup driver formatBarry Grussling2013-01-29
| | | | | | | | Cleanup the format of ethoc.c to meet network driver style as per checkpatch.pl. Signed-off-by: Barry Grussling <barry@grussling.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: remove flags argument from phy_{attach, connect, connect_direct}Florian Fainelli2013-01-14
| | | | | | | | | | | | | | | | The flags argument of the phy_{attach,connect,connect_direct} functions is then used to assign a struct phy_device dev_flags with its value. All callers but the tg3 driver pass the flag 0, which results in the underlying PHY drivers in drivers/net/phy/ not being able to actually use any of the flags they would set in dev_flags. This patch gets rid of the flags argument, and passes phydev->dev_flags to the internal PHY library call phy_attach_direct() such that drivers which actually modify a phy device dev_flags get the value preserved for use by the underlying phy driver. Acked-by: Kosta Zertsekel <konszert@marvell.com> Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethoc: fix mac address setJiri Pirko2013-01-07
| | | | | | | | | Function ethoc_set_mac_address() was incorrectly using passed pointer as pointer to address, that is not correct. Struct sockaddr have to be be used here. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: remove unnecessary NET_ADDR_RANDOM "bitclean"Jiri Pirko2013-01-04
| | | | | | | | NET_ADDR_SET is set in dev_set_mac_address() no need to alter dev->addr_assign_type value in drivers. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: set dev->addr_assign_type correctlyJiri Pirko2013-01-04
| | | | | | | Not a bitfield, but a plain value. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/ethernet: remove __dev* attributesBill Pemberton2012-12-03
| | | | | | | | | | | CONFIG_HOTPLUG is going away as an option. As result the __dev* markings will be going away. Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst, and __devexit. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ethernet: Use eth_random_addrJoe Perches2012-07-17
| | | | | | | | Convert the existing uses of random_ether_addr to the new eth_random_addr. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/ethernet: Fix (nearly-)kernel-doc comments for various functionsBen Hutchings2012-07-11
| | | | | | | | | | Fix incorrect start markers, wrapped summary lines, missing section breaks, incorrect separators, and some name mismatches. Delete a few that are content-free. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethoc: set addr_assign_type if random_ether_addr() usedDanny Kukawka2012-02-17
| | | | | | | | | | | | | | | | | | Set addr_assign_type correctly to NET_ADDR_RANDOM in case a random MAC address was generated and assigned to the netdevice. Fixed ethoc_set_mac_address() to check if the given mac address is valid and set also dev_addr of the net_device. Check also the return value of ethoc_set_mac_address() in ethoc_probe(). Reset the state to NET_ADDR_PERM as soon as the MAC get changed via .ndo_set_mac_address. v2: set net_device->dev_addr in ethoc_set_mac_address(), check if given address is valid Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
* drivers/net: Remove alloc_etherdev error messagesJoe Perches2012-01-31
| | | | | | | | alloc_etherdev has a generic OOM/unable to alloc message. Remove the duplicative messages after alloc_etherdev calls. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: fix up stale paths from driver reorgPaul Gortmaker2012-01-30
| | | | | | | | | | | The reorganization of the driver layout in drivers/net left behind some stale paths in comments and in Kconfig help text. Bring them up to date. No actual change to any code takes place here. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/ethernet: convert drivers/net/ethernet/* to use module_platform_driver()Axel Lin2011-11-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch converts the drivers in drivers/net/ethernet/* to use the module_platform_driver() macro which makes the code smaller and a bit simpler. Cc: "David S. Miller" <davem@davemloft.net> Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com> Cc: Vitaly Bordug <vbordug@ru.mvista.com> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Jiri Pirko <jpirko@redhat.com> Cc: Daniel Hellstrom <daniel@gaisler.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Tobias Klauser <tklauser@distanz.ch> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Richard Cochran <richard.cochran@omicron.at> Cc: Jonas Bonn <jonas@southpole.se> Cc: Sebastian Poehn <sebastian.poehn@belden.com> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl> Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Wan ZongShun <mcuos.com@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net: Add module.h to drivers who were implicitly using itPaul Gortmaker2011-10-31
| | | | | | | | The device.h header was including module.h, making it present for most of these drivers. But we want to clean that up. Call out the include of module.h in the modular network drivers. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* net: remove use of ndo_set_multicast_list in driversJiri Pirko2011-08-17
| | | | | | | replace it by ndo_set_rx_mode Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethoc: Move the Avionic driverJeff Kirsher2011-08-13
Move the Avionic driver into drivers/net/ethernet/ and make the necessary Kconfig and Makefile changes. CC: Thierry Reding <thierry.reding@avionic-design.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-15 10:51:35 -0500