| Commit message (Collapse) | Author | Age |
|---|
| ... | |
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
When the hardware operates in 16 bit mode it always reads 16 bits even
for operations that only have the lower 8 bits defined. So the upper
bits must be discarded. Do this in the read_byte callback instead of
when reading the NAND id to support reading byte wise more than 5 bytes
and at other occations (like reading the ONFI parameter page).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
At least on i.MX25 (i.e. NFCv2) preset_v2 is called with mtd->writesize
== 0 that is before the connect flash chip is detected. It then
configures for 8 bit ECC mode which needs 26 bytes of OOB per 512 bytes
main section. For flashes with a smaller OOB area issuing a read page
command makes the controller stuck with this config.
Note that this currently doesn't hurt because the first read page
command is issued only after detection is complete and preset is called
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
While extending the mxc-nand driver it happend to me a few times that
the device was stuck and this made the machine hang during boot. So
implement a timeout and print a stack trace the first time this happens
to make it debuggable. The return type of the waiting function is also
changed to int to be able to handle the timeout in the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Currently the driver read NFC command registers to get NFC busy flag.
Actually this flag also can be get by reading HSMC_SR register.
Use the read NFC command registers need mapping a huge memory region.
To save the mapped memory region, we change to check NFC busy flag by
reading HSMC_SR register.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Fix typo, "Unkown" -> "Unknown"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
s3c2410_nand_probe is not the name of the function.
These prints have little utility, so let's just kill them.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
pxa3xx_flash_ids wasn't initialized to 0, which in certain cases could
end up containing corrupted values in its members. Fix this to avoid
possible issues.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | |\ \ \ \ |
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Change the handling of the data stage in the driver : don't pump data in
the top-half interrupt, but rather schedule a thread for non dma cases.
This will enable latencies in the data pumping, especially if delays are
required. Moreover platform shall be more reactive as other interrupts
can be served while pumping data.
No throughput degradation was observed, at least on the zylonite
platform, while a slight degradation was being expected.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| | |\ \ \ \ \ |
|
| | | |_|_|/ /
| |/| | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Ensures that block2mtd is triggered after the block devices are enumerated
at boot time.
This issue is seen on BCM2835 (Raspberry Pi) systems when mounting JFFS2
block2mtd filesystems, probably because of the delay on enumerating a USB
MMC card reader.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rodrigo Freire <rfreire@redhat.com>
Signed-off-by: Herton Krzesinski <herton@redhat.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
| |\ \ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Pull UBI/UBIFS updates from Richard Weinberger:
"This pull request includes the following UBI/UBIFS changes:
- powercut emulation for UBI
- a huge update to UBI Fastmap
- cleanups and bugfixes all over UBI and UBIFS"
* tag 'upstream-4.1-rc1' of git://git.infradead.org/linux-ubifs: (50 commits)
UBI: power cut emulation for testing
UBIFS: fix output format of INUM_WATERMARK
UBI: Fastmap: Fall back to scanning mode after ECC error
UBI: Fastmap: Remove is_fm_block()
UBI: Fastmap: Add blank line after declarations
UBI: Fastmap: Remove else after return.
UBI: Fastmap: Introduce may_reserve_for_fm()
UBI: Fastmap: Introduce ubi_fastmap_init()
UBI: Fastmap: Wire up WL accessor functions
UBI: Add accessor functions for WL data structures
UBI: Move fastmap specific functions out of wl.c
UBI: Fastmap: Add new module parameter fm_debug
UBI: Fastmap: Make self_check_eba() depend on fastmap self checking
UBI: Fastmap: Add self check to detect absent PEBs
UBI: Fix stale pointers in ubi->lookuptbl
UBI: Fastmap: Enhance fastmap checking
UBI: Add initial support for fastmap self checks
UBI: Fastmap: Rework fastmap error paths
UBI: Fastmap: Prepare for variable sized fastmaps
UBI: Fastmap: Locking updates
...
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Emulate random power cuts by switching device to ro after a number of
writes to allow simple power cut testing with nand-sim.
Maximum and minimum number of successful writes before power cut and
what kind of writes (EC header, VID header or none) to interrupt
configurable via debugfs.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If we encounter an uncorrectable ECC error while scanning for the fastmap
UBI must not fail hard. Instead fall back to scanning mode.
Reported-by: Alexander Block <Alexander.Block@continental-corporation.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This function was added to fastmap in a very early stage
to have paranoid assertions.
With the current fastmap implementation this assert will never
trigger as fastmap PEBs are not seen by the WL sub-system.
Remove it to save us some CPU cycles.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Another checkpatch complaint:
WARNING: Missing a blank line after declarations
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
checkpatch.pl complains:
WARNING: else is not generally useful after a break or return
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
...and kill another #ifdef.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
...and kill another #ifdef in wl.c. :-)
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Use the new WL accessor functions in fastmap.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fastmap need access to various WL data structures as
fastmap tightly depends on WL.
To make the access less invasive add accessor functions.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Fastmap is tightly connected to the WL sub-system, many fastmap-specific
functionslive in wl.c.
To get rid of most #ifdefs in wl.c move this functions into a new file
and include it into wl.c
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If fm_debug is set fastmap debugging is enabled by default.
This is useful if one wants to debug fastmap on an UBI device
with serves the rootfs.
The the UBI attach mechanism runs long before debugfs can be mounted
and chk_fastmap set.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
...instead of generic self checking.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This self check allows Fastmap to detect absent PEBs while
writing a new fastmap to the MTD device.
It will help to find implementation issues in Fastmap.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In some error paths the WL sub-system gives up on a PEB
and frees it's ubi_wl_entry struct but does not set
the entry in ubi->lookuptbl to NULL.
Fastmap can stumble over such a stale pointer as it uses
ubi->lookuptbl to find all PEBs.
Fix this by introducing a new helper function which free()s
a WL entry and removes the reference from the lookup table.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Don't update the fastmap upon detach if fastmap checking is enabled.
This is poor men's power cut testing feature. :-)
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Using this debugfs knob fastmap self checks can be controlled.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If UBI is unable to write the fastmap to the device
we have make sure that upon next attach UBI will fall
back to scanning mode.
In case we cannot ensure that they only thing we can do
is falling back to read-only mode.
The current error handling code is not powercut proof.
It could happen that a powercut while invalidating would
lead to a state where an too old fastmap could be used upon
attach.
This patch addresses the issue by writing a fake fastmap
super block to a fresh PEB instead of reerasing the existing one.
The fake fastmap super block will UBI case to do a full scan.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The current code assumes that each fastmap has the same amount of PEBs.
So far this is true but will change soon.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
a) Rename ubi->fm_sem to ubi->fm_eba_sem as this semaphore
protects EBA changes.
b) Turn ubi->fm_mutex into a rw semaphore. It will still serialize
fastmap writes but also ensures that ubi_wl_put_peb() is not
interrupted by a fastmap write. We use a rw semaphore to allow
ubi_wl_put_peb() still to be executed in parallel if no fastmap
write is happening.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If we set it for dynamic ones we might confuse various self checks.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
ubi_wl_get_peb() returns a fresh PEB which can be used by
user of UBI. Due to the pool logic fastmap will correctly
map this PEB upon attach time because it will be scanned.
If a new fastmap is written (due to heavy parallel io)
while the before the fresh PEB is assigned to the EBA table
it will not be scanned as it is no longer in the pool.
So, the race window exists between ubi_wl_get_peb()
and the EBA table assignment.
We have to make sure that no new fastmap can be written
while that.
To ensure that ubi_wl_get_peb() will grab ubi->fm_sem in read mode
and the user of ubi_wl_get_peb() has to release it after the PEB
got assigned.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If a LEB is unmapped we have to decrement leb_count as well.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Don't use a fixed size for the WL pool.
Make it instead 50% of the user pool.
We don't make it 100% as it is not as heavily used as the user pool.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We have to switch to ro mode to guarantee that upon next UBI attach
all data is consistent.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This logic is in vain as we treat protected PEBs also as used, so this
case must not happen.
If a PEB is found which is in the EBA table but not known as used
has to be issued as fatal error.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
It is legal to have PEBs left in the used list.
This can happen if UBI copies a PEB and a powercut happens
between writing a new fastmap and adding this PEB into the EBA table.
In this case the old PEB will be used.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This function a) requests a new PEB, b) writes data to it,
c) returns the old PEB and d) registers the new PEB in the EBA table.
For the non-fastmap case this works perfectly fine and is powercut safe.
Is fastmap enabled this can lead to issues.
If a new fastmap is written between a) and c) the freshly requested PEB
is no longer in a pool and will not be scanned upon attaching.
If now a powercut happens between c) and d) the freshly requested PEB
will not be scanned and the old one got already scheduled for erase.
After attaching the EBA table will point to a erased PEB.
Fix this issue by swapping steps c) and d).
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
There is always exactly one ubi_attach_info object allocated,
therefore we don't have to care about the name.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Currently we leak a few ubi_ainf_pebs while attaching.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
There is no need to switch to ro mode if ubi_update_fastmap() fails.
Also get rid of the ifdef.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
...such that we can implement NOP variants of some functions.
This will help to reduce fastmap specific ifdefs in other c files.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If ubi_update_fastmap() fails notify the user.
This is not a hard error as ubi_update_fastmap() makes sure that upon failure
the current on-flash fastmap will no be used upon next UBI attach.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add a ubi_fastmap_close() to free all resources used by fastmap
at WL shutdown.
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
There is no need to allocate new ones every time, we can reuse
the existing ones.
This makes the code cleaner and more easy to follow.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Currently ubi_refill_pools() first fills the first and then
the second one.
If only very few free PEBs are available the second pool can get
zero PEBs.
Change ubi_refill_pools() to distribute free PEBs fair between
all pools.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Make it two functions, wl_get_wle() and wl_get_peb().
wl_get_peb() works exactly like __wl_get_peb() but wl_get_wle()
does not call produce_free_peb().
While refilling the fastmap user pool we cannot release ubi->wl_lock
as produce_free_peb() does.
Hence the fastmap logic uses now wl_get_wle().
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
ubi_wl_get_peb() has two problems, it reads the pool
size and usage counters without any protection.
While reading one value would be perfectly fine it reads multiple
values and compares them. This is racy and can lead to incorrect
pool handling.
Furthermore ubi_update_fastmap() is called without wl_lock held,
before incrementing the used counter it needs to be checked again.
It could happen that another thread consumed all PEBs from the
pool and the counter goes beyond ->size.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
...otherwise the deferred work might run after datastructures
got freed and corrupt memory.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
|
