aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/mmc
Commit message (Collapse)AuthorAge
* mfd/mmc: SDHI Kconfig updateMagnus Damm2010-03-07
| | | | | | | | | Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM processors. While at it, make CONFIG_TMIO_MMC depend on CONFIG_MFD_SH_MOBILE_SDHI. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* tmio_mmc: Balance cell enable()/disable() callsMagnus Damm2010-03-07
| | | | | | | | This patch adds cell->disable() calls to the tmio-mmc probe() error handling and the remove() function. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* tmio_mmc: Use 100ms mmc_detect_change() delayMagnus Damm2010-03-07
| | | | | | | | | | | | | | | This patch changes the tmio_mmc driver to wait 100ms before checking the card detect status. This type of delay is quite common among mmc drivers, it seems that most hardware platforms need to give the hardware some time to settle before checking card availabilty. Hotplug is half-broken without this patch on the sh7724 Ecovec board. Hot insertion seems ok but eject is never detected without this patch. Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* tmio_mmc: Add MMC_CAP_MMC_HIGHSPEED support V2Yusuke Goda2010-03-07
| | | | | | | | | Enable MMC_CAP_XX support in the tmio_mmc driver if pdata->capabilities is set. Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* tmio_mmc: Keep card-detect interrupts enabledGuennadi Liakhovetski2010-03-07
| | | | | | | | | | On SuperH platforms the SDHI controller does not produce any command IRQs after a completed IO. This leads to card-detect interrupts staying disabled. Do not disable card-detect interrupts on DATA IRQs. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* mmc: enable DMA on Ricoh sdhci reader by defaultVasily Khoruzhick2010-03-06
| | | | | | | | | | | | | | | This card reader doesn't advertise, however DMA works well. Probably windows SDHCI driver assumes that all readers support DMA and thus we see that bug. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Tested-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Cc: Harald Welte <HaraldWelte@viatech.com> Cc: Norbert Preining <preining@logic.at> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: correct kunmap_atomic()Nicolas Ferre2010-03-06
| | | | | | | | | | | | kunmap_atomic() accepts a pointer to any location in the page so we do not need the subtraction and cast. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Wolfgang Muees <wolfgang.mues@auerswald.de> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: introduce per-mci-revision conditional codeNicolas Ferre2010-03-06
| | | | | | | | | | | | | | | We used to manage features and differences on a per-cpu basis. As several cpus share the same mci revision, this patch aggregates cpus that have the same IP revision in one defined constant. We use the at91mci_is_mci1rev2xx() funtion name not to mess with newer Atmel sd/mmc IP called "MCI2". _rev2 naming could have been confusing... Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Wolfgang Muees <wolfgang.mues@auerswald.de> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: Enable MMC_CAP_SDIO_IRQ only when it actually works.Nicolas Ferre2010-03-06
| | | | | | | | | | | | | According to the datasheets AT91SAM9261 does not support SDIO interrupts, and AT91SAM9260/9263 have an erratum requiring 4bit mode while using slot B for the interrupt to work. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Wolfgang Muees <wolfgang.mues@auerswald.de> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: enable large data blocksWolfgang Muees2010-03-06
| | | | | | | | | | | | | | | | | | | | | This patch is setting some max_ variables for the IO elevator, so the elevator will put requests for large data blocks to the driver. This is critical for a) speed and b) wear leveling of the flash chip controller: Otherwise the controller will treat the SD card badly with millions of single 4 KByte write commands. This will lead to a shorter life time for the SD cards. Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: use DMA buffer for readWolfgang Muees2010-03-06
| | | | | | | | | | | | | | | Convert the read to use the DMA buffer as well. The old code was doing double-buffering DMA with the PDC; no way to make it work. Replace it with a single-PDC approach. It also simplify things removing the need for a pre_dma_read() function. [nicolas.ferre@atmel.com coding style modifications] Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: use one coherent DMA bufferWolfgang Muees2010-03-06
| | | | | | | | | | | | | | | | The TX DMA buffer is allocated only once, because the allocation/deallocation of the buffer for EACH chunk of data is time-consuming and prone to memory fragmentation. Using a coherent DMA buffer avoids extra data cache calls. [nicolas.ferre@atmel.com: coding style modifications] Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: fix timeout errorsWolfgang Muees2010-03-06
| | | | | | | | | | | | Fix two timeout errors, one for slow SDHC cards and one for slow users while inserting SD cards. Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: at91_mci: fix pointer errorsWolfgang Muees2010-03-06
| | | | | | | | | | | | Fixes two pointer errors, one which leads to memory overwrites if used with large chunks of data. Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <avictor.za@gmail.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* s3cmci: s3cmci_card_present: Use no_detect to decide whether there is a card ↵Lars-Peter Clausen2010-03-06
| | | | | | | | | | | detect pin Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Ben Dooks <ben-linux@fluff.org> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* s3cmci: initialize default platform data no_wprotect and no_detect with 1Lars-Peter Clausen2010-03-06
| | | | | | | | | | | | | | | | | | | If no platform_data was givin to the device it's going to use it's default platform data struct which has all fields initialized to zero. As a result the driver is going to try to request gpio0 both as write protect and card detect pin. Which of course will fail and makes the driver unusable Previously to the introduction of no_wprotect and no_detect the behavior was to assume that if no platform data was given there is no write protect or card detect pin. This patch restores that behavior. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Ben Dooks <ben-linux@fluff.org> Cc: <linux-mmc@vger.kernel.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdio: put active devices into 1-bit mode during suspendDaniel Drake2010-03-06
| | | | | | | | | | And bring them back to 4-bit mode during resume. Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdio: kick the interrupt thread upon a resumeNicolas Pitre2010-03-06
| | | | | | | | | | | | Some SDIO cards may suspend while keeping function interrupts active especially in the powered suspend case. Upon resume we need to kick the SDIO interrupt thread to check for pending interrupts and to restart card IRQ detection at the host controller level. Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdio: don't use CMD[357] as part of a powered SDIO resumeChris Ball2010-03-06
| | | | | | | | | | | | | Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid sending CMD3/5/7 on a resume where power has been maintained, because the 8686 will refuse to respond to them and the MMC stack will give up on the card. Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdio: sdhci support for suspend mode PM featuresNicolas Pitre2010-03-06
| | | | | | | | | Tested with an XO v1.5 from OLPC. Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdio: introduce API for special power management featuresNicolas Pitre2010-03-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch series provides the core changes needed to allow SDIO cards to remain powered and active while the host system is suspended, and let them wake up the host system when needed. This is used to implement wake-on-lan with SDIO wireless cards at the moment. Patches to add that support to the libertas driver will be posted separately. This patch: Some SDIO cards have the ability to keep on running autonomously when the host system is suspended, and wake it up when needed. This however requires that the host controller preserve power to the card, and configure itself appropriately for wake-up. There is however 4 layers of abstractions involved: the host controller driver, the MMC core code, the SDIO card management code, and the actual SDIO function driver. To make things simple and manageable, host drivers must advertise their PM capabilities with a feature bitmask, then function drivers can query and set those features from their suspend method. Then each layer in the suspend call chain is expected to act upon those bits accordingly. [akpm@linux-foundation.org: fix typo in comment] Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdhci: improve sdhci sdhci_set_adma_desc() codeBen Dooks2010-03-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sdhci_set_adma_desc() is using byte-writes to write data in a specified order into memory. Change to using __le16 for the two byte and __le32 for the four byte cases and use the cpu_to_{le16,le32} to do the conversion before writing. This will reduce the size of the code and the number of writes as we no longer need to chop the data up before writing. As an example on ARM S3C64XX SoC, in little-endian configuration: 000000d4 <sdhci_set_adma_desc>: - d8: e1a0c423 lsr ip, r3, #8 - dc: e1a0ec21 lsr lr, r1, #24 - e0: e1a04821 lsr r4, r1, #16 - e4: e1a05421 lsr r5, r1, #8 - e8: e1a06442 asr r6, r2, #8 - ec: e5c0c001 strb ip, [r0, #1] - f0: e5c0e007 strb lr, [r0, #7] - f4: e5c04006 strb r4, [r0, #6] - f8: e5c05005 strb r5, [r0, #5] - fc: e5c01004 strb r1, [r0, #4] - 100: e5c06003 strb r6, [r0, #3] - 104: e5c02002 strb r2, [r0, #2] - 108: e5c03000 strb r3, [r0] + d4: e5801004 str r1, [r0, #4] + d8: e1c030b0 strh r3, [r0] + dc: e1c020b2 strh r2, [r0, #2] Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Pierre Ossman <pierre@ossman.eu> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdhci: add adma descriptor set callBen Dooks2010-03-06
| | | | | | | | | | | | | The code to write the ADMA descriptor into memory is repeated several times throughout sdhci_adma_table_pre, and thus should be moved into a common function. This will also be useful if the patch to make the write more efficient is accepted. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Pierre Ossman <pierre@ossman.eu> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sdio: add quirk to clamp byte mode transferBing Zhao2010-03-06
| | | | | | | | | | | | | Some SDIO cards expect byte transfers not to exceed the configured block transfer size. Add a quirk to that effect. Patches to make use of this quirk will be sent separately. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Nicolas Pitre <nico@marvell.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: bfin_sdh: set timeout based on actual card dataCliff Cai2010-03-06
| | | | | | | | | | The hardcoded value doesn't really work for all cards. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: bfin_sdh: drop redundant MMC depend stringMike Frysinger2010-03-06
| | | | | | | | | The host/Kconfig file is only included when MMC is selected. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: bfin_sdh: fix unused sg warning on BF51x/BF52x systemsMike Frysinger2010-03-06
| | | | | | | | | The local sg variable is only used with BF54x code. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* mmc: Atmel host kconfig cleanup for everyone elseNicolas Ferre2010-03-06
| | | | | | | | | | | This prevents those without an Atmel chip having a line in kernel configuration which says "Atmel SD/MMC Driver" without any option. Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* davinci: MMC: add support for 8bit MMC cardsVipin Bhandari2010-03-06
| | | | | | | | | | | | | | | Add support for 8bit MMC cards. The controller data width is configurable depending on the wires setting in the platform data structure. MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM. Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com> Cc: David Brownell <david-b@pacbell.net> Cc: Chaithrika U S <chaithrika@ti.com> Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* ricoh_mmc: port from driver to pci quirkMaxim Levitsky2010-03-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch solves nasty problem original driver has. Original goal of the ricoh_mmc was to disable this device because then, mmc cards can be read using standard SDHCI controller, thus avoiding writing of yet another driver. However, the act of disablement, makes other pci functions that belong to this controller (xD and memstick) shift up one level, thus pci core has now wrong idea about these devices. To fix this issue, this patch moves the driver into the pci quirk section, thus it is executes before the pci is enumerated, and therefore solving that issue, also same sequence of commands is performed on resume for same reasons. Also regardless of the above, this way is cleaner. You still need to set CONFIG_MMC_RICOH_MMC to enable this quirk Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Acked-by: Philip Langdale <philipl@overt.org> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6Linus Torvalds2010-03-03
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits) jsm: fixing error if the driver fails to load jsm: removing the uart structure and filename on error tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call tty: Keep the default buffering to sub-page units tty: Fix up char drivers request_room usage tty: Fix the ldisc hangup race serial: timberdale: Remove dependancies nozomi: Tidy up the PCI table nozomi: Fix mutex handling nozomi: Add tty_port usage sdio_uart: Use kfifo instead of the messy circ stuff serial: bcm63xx_uart: allow more than one uart to be registered. serial: bcm63xx_uart: don't use kfree() on non kmalloced area. serial: bfin_5xx: pull in linux/io.h for ioremap prototypes serial: bfin_5xx: kgdboc should accept gdb break only when it is active serial: bfin_5xx: need to disable DMA TX interrupt too serial: bfin_5xx: remove useless gpio handling with hard flow control Char: synclink, remove unnecessary checks tty: declare MODULE_FIRMWARE in various drivers ip2: Add module parameter. ...
| * sdio_uart: Use kfifo instead of the messy circ stuffAlan Cox2010-03-02
| | | | | | | | | | | | | | | | | | Revised patch to use the new kfifo API. This replaces the one that was dropped from -next due to collisions with the kfifo API changes. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | Merge with mainline to remove plat-omap/Kconfig conflictTony Lindgren2010-03-01
|\| | | | | | | | | Conflicts: arch/arm/plat-omap/Kconfig
| * Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds2010-03-01
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits) ARM: Eliminate decompressor -Dstatic= PIC hack ARM: 5958/1: ARM: U300: fix inverted clk round rate ARM: 5956/1: misplaced parentheses ARM: 5955/1: ep93xx: move timer defines into core.c and document ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c ARM: 5953/1: ep93xx: fix broken build of clock.c ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig ARM: 5949/1: NUC900 add gpio virtual memory map ARM: 5948/1: Enable timer0 to time4 clock support for nuc910 ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk ARM: make_coherent(): fix problems with highpte, part 2 MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself ARM: 5945/1: ep93xx: include correct irq.h in core.c ARM: 5933/1: amba-pl011: support hardware flow control ARM: 5930/1: Add PKMAP area description to memory.txt. ARM: 5929/1: Add checks to detect overlap of memory regions. ARM: 5928/1: Change type of VMALLOC_END to unsigned long. ARM: 5927/1: Make delimiters of DMA area globally visibly. ARM: 5926/1: Add "Virtual kernel memory..." printout. ARM: 5920/1: OMAP4: Enable L2 Cache ... Fix up trivial conflict in arch/arm/mach-mx25/clock.c
| | *-----. Merge branches 'at91', 'cache', 'cup', 'ep93xx', 'ixp4xx', 'nuc', ↵Russell King2010-02-25
| | |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | 'pending-dma-streaming', 'u300' and 'umc' into devel
| | | | | * | ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printkLinus Walleij2010-02-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This removes the custom DBG macro in favor of the in-kernel dev_dbg() macro. Probably a leftover from a time when dev_dbg() didn't yet exist. Also remove a printk() in favor of dev_err(). Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | | | | * | ARM: 5896/1: MMCI: work around a hardware bug in U300Linus Walleij2010-01-27
| | | |_|/ / | | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the U300 some hardware bug makes the status flag not come up signalling a successful write (or anything else, like an error, for that matter) on write requests. This little quirk makes the writes work on U300. Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| * | | | | Merge branch 'for-2.6.34' of git://git.kernel.dk/linux-2.6-blockLinus Torvalds2010-03-01
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits) block: don't access jiffies when initialising io_context cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds block: fix for "Consolidate phys_segment and hw_segment limits" cfq-iosched: quantum check tweak blktrace: perform cleanup after setup error blkdev: fix merge_bvec_fn return value checks cfq-iosched: requests "in flight" vs "in driver" clarification cciss: Fix problem with scatter gather elements in the scsi half of the driver cciss: eliminate unnecessary pointer use in cciss scsi code cciss: do not use void pointer for scsi hba data cciss: factor out scatter gather chain block mapping code cciss: fix scatter gather chain block dma direction kludge cciss: simplify scatter gather code cciss: factor out scatter gather chain block allocation and freeing cciss: detect bad alignment of scsi commands at build time cciss: clarify command list padding calculation cfq-iosched: rethink seeky detection for SSDs cfq-iosched: rework seeky detection block: remove padding from io_context on 64bit builds block: Consolidate phys_segment and hw_segment limits ...
| | * | | | | block: Consolidate phys_segment and hw_segment limitsMartin K. Petersen2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Except for SCSI no device drivers distinguish between physical and hardware segment limits. Consolidate the two into a single segment limit. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
| | * | | | | block: Rename blk_queue_max_sectors to blk_queue_max_hw_sectorsMartin K. Petersen2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The block layer calling convention is blk_queue_<limit name>. blk_queue_max_sectors predates this practice, leading to some confusion. Rename the function to appropriately reflect that its intended use is to set max_hw_sectors. Also introduce a temporary wrapper for backwards compability. This can be removed after the merge window is closed. Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
| * | | | | | MMC: AU1xMMC: Allow platforms to disable host capabilitiesManuel Lauss2010-02-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Although the hardware supports a 4/8bit SD interface and the driver unconditionally advertises all hardware caps to the MMC core, not all datalines may actually be wired up. This patch introduces another field to au1xmmc platform data allowing platforms to disable certain advanced host controller features. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> To: linux-mmc@vger.kernel.org CC: Linux-MIPS <linux-mips@linux-mips.org> Patchwork: http://patchwork.linux-mips.org/patch/460/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * | | | | | MIPS: Alchemy: change dbdma to accept physical memory addressesManuel Lauss2010-02-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DMA can only be done from physical addresses; move the "virt_to_phys" source/destination buffer address translation from the dbdma queueing functions (since the hardware can only DMA to/from physical addresses) to their respective users. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * | | | | | MIPS: Alchemy: remove dbdma compat macrosManuel Lauss2010-02-27
| |/ / / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove dbdma compat macros, move remaining users over to default queueing functions and -flags. (Queueing function signature has changed in order to give a build failure instead of silent functional changes due to the no longer implicitly specified DDMA_FLAGS_IE flag) Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* | | | | | Merge branch 'omap-fixes-for-linus' into omap-for-linusTony Lindgren2010-02-17
|\| | | | |
| * | | | | mmc_test: block addressed cardsJohan Kristell2010-02-11
| | |_|_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a bug in the multiblock write tests where the written data is read back for verifying one block at a time. The tests in mmc_test assumes that all cards are byte addressable. This will cause the multi block write tests to fail, leading the user of the mmc_test driver thinking there is something wrong with the sdhci driver they are testing. The start address for the block is calculated as: blocknum * 512. For block addressable cards the blocknum alone should be used. Signed-off-by: Johan Kristell <johan.kristell@axis.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | omap_hsmmc: allow compile without regulator frameworkAdrian Hunter2010-02-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is still possible to use the omap_hsmmc module without the regulator framework. Accordingly, ifdef out regulator-specific functions. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | | | | omap_hsmmc: Allow for a shared VccQAdrian Hunter2010-02-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EMMC can have two voltage supplies, Vcc and VccQ which are implemented in the code as consumer supplies vmmc and vmmc_aux. If the regulator that supplies vmmc_aux is shared with other consumers, then sending it to sleep will disrupt those consumers. However, the TWL4030-family regulators may have OFF remapped to SLEEP, in which case 'regulator_disable()' will put the regulator to sleep only when all consumers are disabled - which is the desired behaviour. This patch adds a platform data field to allow that option. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | | | | omap_hsmmc: Ensure regulator enable / disable are pairedAdrian Hunter2010-02-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Stop using 'regulator_is_enabled()' and just pair enables with disables so that the regulator reference counts can work correctly. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | | | | omap_hsmmc: Fix disable timeoutsAdrian Hunter2010-02-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Disable timeouts are in msecs not jiffies. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | | | | omap_hsmmc: Allow for power saving without going offAdrian Hunter2010-02-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | An eMMC may be always powered on, so that the lowest power saving state possible is sleeping. Add a field to the platform data to indicate that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-19 03:26:26 -0500