| Commit message (Collapse) | Author | Age |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Merge random patches from Andrew Morton.
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (32 commits)
memblock: free allocated memblock_reserved_regions later
mm: sparse: fix usemap allocation above node descriptor section
mm: sparse: fix section usemap placement calculation
xtensa: fix incorrect memset
shmem: cleanup shmem_add_to_page_cache
shmem: fix negative rss in memcg memory.stat
tmpfs: revert SEEK_DATA and SEEK_HOLE
drivers/rtc/rtc-twl.c: fix threaded IRQ to use IRQF_ONESHOT
fat: fix non-atomic NFS i_pos read
MAINTAINERS: add OMAP CPUfreq driver to OMAP Power Management section
sgi-xp: nested calls to spin_lock_irqsave()
fs: ramfs: file-nommu: add SetPageUptodate()
drivers/rtc/rtc-mxc.c: fix irq enabled interrupts warning
mm/memory_hotplug.c: release memory resources if hotadd_new_pgdat() fails
h8300/uaccess: add mising __clear_user()
h8300/uaccess: remove assignment to __gu_val in unhandled case of get_user()
h8300/time: add missing #include <asm/irq_regs.h>
h8300/signal: fix typo "statis"
h8300/pgtable: add missing #include <asm-generic/pgtable.h>
drivers/rtc/rtc-ab8500.c: ensure correct probing of the AB8500 RTC when Device Tree is enabled
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The code here has a nested spin_lock_irqsave(). It's not needed since
IRQs are already disabled and it causes a problem because it means that
IRQs won't be enabled again at the end. The second call to
spin_lock_irqsave() will overwrite the value of irq_flags and we can't
restore the proper settings.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
when the default irq quick handler is used then IRQF_ONESHOT must be set
otherwise the request fails and following error is displayed:
mei 0000:00:16.0: irq 48 for MSI/MSI-X
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq 48
mei 0000:00:16.0: request_threaded_irq failed: irq = 48.
dpm_run_callback(): pci_pm_resume+0x0/0x140 returns -22
PM: Device 0000:00:16.0 failed to resume async: error -22
Reported-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
mei watchdog doesn't reboot the system it only produces event
therefore mark it as WDIOF_ALARMONLY.
This patch depends on:
commit 2bbeed016dd96045ec82c3a309afddcc3a0db1d2
Author: Alan Cox <alan@linux.intel.com>
watchdog: Add a flag to indicate the watchdog doesn't reboot things
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
| |
Since MSI is enabled right before that, we should disable it when
registration fails.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This bug caused severe connectivity issue in the LMS application
(LMS is described in Documentation/misc-devices/mei/mei.txt)
The bug was introduced in patch:
commit 1ccb7b6249f9bc50678e2a383084ed0a34cc9239
staging/mei: propagate error codes up in the write flow
The patch has reverted the return value logic of some fo function but
the conditional in _mei_irq_thread_read function was not swapped
making read always entering the error path
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
| |
Since the misc device is registered only in the pci probe function
it has to be also unregistered in the counterpart pci remove function
and not in the module exit function.
In case of probe failure the driver was oopsing in module exit function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |
|
|
|
|
|
|
|
|
| |
when the default irq quick handler is used then IRQF_ONESHOT must be set
otherwise the request fails and following error is displayed:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq ...
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch ensures probing of the ab8500-pwm driver during a DT
enabled boot, so long as the associated nodes are present in the
Device Tree binary.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Strictly speaking "no" is a valid, but undefined, Kconfig symbol. But what
obviously was meant here was "n".
While we're touching this Kconfig file also drop the superfluous
dependency on C2PORT for C2PORT_DURAMAR_2150. Its Kconfig entry is
already wrapped in "if C2PORT" and "endif".
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree changes from Greg Kroah-Hartman:
"Here is the big staging tree pull request for the 3.5-rc1 merge
window.
Loads of changes here, and we just narrowly added more lines than we
added:
622 files changed, 28356 insertions(+), 26059 deletions(-)
But, good news is that there is a number of subsystems that moved out
of the staging tree, to their respective "real" portions of the
kernel.
Code that moved out was:
- iio core code
- mei driver
- vme core and bridge drivers
There was one broken network driver that moved into staging as a step
before it is removed from the tree (pc300), and there was a few new
drivers added to the tree:
- new iio drivers
- gdm72xx wimax USB driver
- ipack subsystem and 2 drivers
All of the movements around have acks from the various subsystem
maintainers, and all of this has been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up various trivial conflicts, along with a non-trivial one found
in -next and pointed out by Olof Johanssen: a clean - but incorrect -
merge of the arch/arm/boot/dts/at91sam9g20.dtsi file. Fix up manually
as per Stephen Rothwell.
* tag 'staging-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (536 commits)
Staging: bcm: Remove two unused variables from Adapter.h
Staging: bcm: Removes the volatile type definition from Adapter.h
Staging: bcm: Rename all "INT" to "int" in Adapter.h
Staging: bcm: Fix warning: __packed vs. __attribute__((packed)) in Adapter.h
Staging: bcm: Correctly format all comments in Adapter.h
Staging: bcm: Fix all whitespace issues in Adapter.h
Staging: bcm: Properly format braces in Adapter.h
Staging: ipack/bridges/tpci200: remove unneeded casts
Staging: ipack/bridges/tpci200: remove TPCI200_SHORTNAME constant
Staging: ipack: remove board_name and bus_name fields from struct ipack_device
Staging: ipack: improve the register of a bus and a device in the bus.
staging: comedi: cleanup all the comedi_driver 'detach' functions
staging: comedi: remove all 'default N' in Kconfig
staging: line6/config.h: Delete unused header
staging: gdm72xx depends on NET
staging: gdm72xx: Set up parent link in sysfs for gdm72xx devices
staging: drm/omap: initial dmabuf/prime import support
staging: drm/omap: dmabuf/prime mmap support
pstore/ram: Add ECC support
pstore/ram: Switch to persistent_ram routines
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
1. move mei.txt, TODO, and the example code under Documentation/misc-devices/mei
2. update the TODO file
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The header exports API for application layer
1. move under include/linux and add to the export list
2. update include path n the sources
3. update TODO
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
pr_ format is more compact and enable utilizing of pr_fmt macro
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| | |
It's been cleaned up, and there's nothing else left to do, so move it
out of staging into drivers/misc/ where all can use it now.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Oren Weil <oren.jer.weil@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch remove old max8997-muic drvier because of newly Extcon framework.
Extcon framework manages the external connector, so add extcon-max8997 driver
by using Extcon interface to support MUIC feature of Maxim 8997 PMIC instead
of max8997-muic driver(drivers/misc/max8997-muic.c).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Updated the generic SPI EEPROM driver AT25 for support of an additional address
bit in the instruction byte. Certain EEPROMS have a size that is larger than the
number of address bytes would allow (e.g. like M95040 from ST that has 512 Byte
size but uses only one address byte (A0 to A7) for addressing.) For the extra
address bit (A8, A16 or A24) bit 3 of the instruction byte is used. This
instruction bit is normally defined as don't care for other AT25 like chips.
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The bmp18x chip family comes in an I2C respectively SPI variant.
Hence, the bmp085 driver was split to support both buses.
Tested-by: Zhengguang Guo <zhengguang.guo@bosch-sensortec.com>
Reviewed-by: Stefan Nilsson <stefan.nilsson@unixphere.com>
Signed-off-by: Eric Andersson <eric.andersson@unixphere.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| | |
Reviewed-by: Stefan Nilsson <stefan.nilsson@unixphere.com>
Signed-off-by: Eric Andersson <eric.andersson@unixphere.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch includes various cleaning of the bmp085 driver including:
- Whitespaces and alignment fixes
- Minor typos
- Consistency fixes
Reviewed-by: Stefan Nilsson <stefan.nilsson@unixphere.com>
Signed-off-by: Eric Andersson <eric.andersson@unixphere.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
No symbol can be exported when the section is discarded - the only
solution I could think of is not to mark symbols as __devexit
when they are exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Drivers that refer to a __devexit function in an operations
structure need to annotate that pointer with __devexit_p so it
is replaced with a NULL pointer when the section gets discarded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |/
|
|
|
|
|
|
|
|
| |
Current code does not properly free allocated irqs if request_threaded_irq
returns error, fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB regression fixes from Jason Wessel:
- Fix a Smatch warning that appeared in the 3.4 merge window
- Fix kgdb test suite with SMP for all archs without HW single stepping
- Fix kgdb sw breakpoints with CONFIG_DEBUG_RODATA=y limitations on x86
- Fix oops on kgdb test suite with CONFIG_DEBUG_RODATA
- Fix kgdb test suite with SMP for all archs with HW single stepping
* tag 'for_linus-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
x86,kgdb: Fix DEBUG_RODATA limitation using text_poke()
kgdb,debug_core: pass the breakpoint struct instead of address and memory
kgdbts: (2 of 2) fix single step awareness to work correctly with SMP
kgdbts: (1 of 2) fix single step awareness to work correctly with SMP
kgdbts: Fix kernel oops with CONFIG_DEBUG_RODATA
kdb: Fix smatch warning on dbg_io_ops->is_console
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
There has long been a limitation using software breakpoints with a
kernel compiled with CONFIG_DEBUG_RODATA going back to 2.6.26. For
this particular patch, it will apply cleanly and has been tested all
the way back to 2.6.36.
The kprobes code uses the text_poke() function which accommodates
writing a breakpoint into a read-only page. The x86 kgdb code can
solve the problem similarly by overriding the default breakpoint
set/remove routines and using text_poke() directly.
The x86 kgdb code will first attempt to use the traditional
probe_kernel_write(), and next try using a the text_poke() function.
The break point install method is tracked such that the correct break
point removal routine will get called later on.
Cc: x86@kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org # >= 2.6.36
Inspried-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The do_fork and sys_open tests have never worked properly on anything
other than a UP configuration with the kgdb test suite. This is
because the test suite did not fully implement the behavior of a real
debugger. A real debugger tracks the state of what thread it asked to
single step and can correctly continue other threads of execution or
conditionally stop while waiting for the original thread single step
request to return.
Below is a simple method to cause a fatal kernel oops with the kgdb
test suite on a 2 processor ARM system:
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
echo V1I1F100 > /sys/module/kgdbts/parameters/kgdbts
Very soon after starting the test the kernel will start warning with
messages like:
kgdbts: BP mismatch c002487c expected c0024878
------------[ cut here ]------------
WARNING: at drivers/misc/kgdbts.c:317 check_and_rewind_pc+0x9c/0xc4()
[<c01f6520>] (check_and_rewind_pc+0x9c/0xc4)
[<c01f595c>] (validate_simple_test+0x3c/0xc4)
[<c01f60d4>] (run_simple_test+0x1e8/0x274)
The kernel will eventually recovers, but the test suite has completely
failed to test anything useful.
This patch implements behavior similar to a real debugger that does
not rely on hardware single stepping by using only software planted
breakpoints.
In order to mimic a real debugger, the kgdb test suite now tracks the
most recent thread that was continued (cont_thread_id), with the
intent to single step just this thread. When the response to the
single step request stops in a different thread that hit the original
break point that thread will now get continued, while the debugger
waits for the thread with the single step pending. Here is a high
level description of the sequence of events.
cont_instead_of_sstep = 0;
1) set breakpoint at do_fork
2) continue
3) Save the thread id where we stop to cont_thread_id
4) Remove breakpoint at do_fork
5) Reset the PC if needed depending on kernel exception type
6) soft single step
7) Check where we stopped
if current thread != cont_thread_id {
if (here for more than 2 times for the same thead) {
### must be a really busy system, start test again ###
goto step 1
}
goto step 5
} else {
cont_instead_of_sstep = 0;
}
8) clean up and run test again if needed
9) Clear out any threads that were waiting on a break point at the
point in time the test is ended with get_cont_catch(). This
happens sometimes because breakpoints are used in place of single
stepping and some threads could have been in the debugger exception
handling queue because breakpoints were hit concurrently on
different CPUs. This also means we wait at least one second before
unplumbing the debugger connection at the very end, so as respond
to any debug threads waiting to be serviced.
Cc: stable@vger.kernel.org # >= 3.0
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The do_fork and sys_open tests have never worked properly on anything
other than a UP configuration with the kgdb test suite. This is
because the test suite did not fully implement the behavior of a real
debugger. A real debugger tracks the state of what thread it asked to
single step and can correctly continue other threads of execution or
conditionally stop while waiting for the original thread single step
request to return.
Below is a simple method to cause a fatal kernel oops with the kgdb
test suite on a 4 processor x86 system:
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
while [ 1 ] ; do ls > /dev/null 2> /dev/null; done&
echo V1I1F1000 > /sys/module/kgdbts/parameters/kgdbts
Very soon after starting the test the kernel will oops with a message like:
kgdbts: BP mismatch 3b7da66480 expected ffffffff8106a590
WARNING: at drivers/misc/kgdbts.c:303 check_and_rewind_pc+0xe0/0x100()
Call Trace:
[<ffffffff812994a0>] check_and_rewind_pc+0xe0/0x100
[<ffffffff81298945>] validate_simple_test+0x25/0xc0
[<ffffffff81298f77>] run_simple_test+0x107/0x2c0
[<ffffffff81298a18>] kgdbts_put_char+0x18/0x20
The warn will turn to a hard kernel crash shortly after that because
the pc will not get properly rewound to the right value after hitting
a breakpoint leading to a hard lockup.
This change is broken up into 2 pieces because archs that have hw
single stepping (2.6.26 and up) need different changes than archs that
do not have hw single stepping (3.0 and up). This change implements
the correct behavior for an arch that supports hw single stepping.
A minor defect was fixed where sys_open should be do_sys_open
for the sys_open break point test. This solves the problem of running
a 64 bit with a 32 bit user space. The sys_open() never gets called
when using the 32 bit file system for the kgdb testsuite because the
32 bit binaries invoke the compat_sys_open() call leading to the test
never completing.
In order to mimic a real debugger, the kgdb test suite now tracks the
most recent thread that was continued (cont_thread_id), with the
intent to single step just this thread. When the response to the
single step request stops in a different thread that hit the original
break point that thread will now get continued, while the debugger
waits for the thread with the single step pending. Here is a high
level description of the sequence of events.
cont_instead_of_sstep = 0;
1) set breakpoint at do_fork
2) continue
3) Save the thread id where we stop to cont_thread_id
4) Remove breakpoint at do_fork
5) Reset the PC if needed depending on kernel exception type
6) if (cont_instead_of_sstep) { continue } else { single step }
7) Check where we stopped
if current thread != cont_thread_id {
cont_instead_of_sstep = 1;
goto step 5
} else {
cont_instead_of_sstep = 0;
}
8) clean up and run test again if needed
Cc: stable@vger.kernel.org # >= 2.6.26
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
On x86 the kgdb test suite will oops when the kernel is compiled with
CONFIG_DEBUG_RODATA and you run the tests after boot time. This is
regression has existed since 2.6.26 by commit: b33cb815 (kgdbts: Use
HW breakpoints with CONFIG_DEBUG_RODATA).
The test suite can use hw breakpoints for all the tests, but it has to
execute the hardware breakpoint specific tests first in order to
determine that the hw breakpoints actually work. Specifically the
very first test causes an oops:
# echo V1I1 > /sys/module/kgdbts/parameters/kgdbts
kgdb: Registered I/O driver kgdbts.
kgdbts:RUN plant and detach test
Entering kdb (current=0xffff880017aa9320, pid 1078) on processor 0 due to Keyboard Entry
[0]kdb> kgdbts: ERROR PUT: end of test buffer on 'plant_and_detach_test' line 1 expected OK got $E14#aa
WARNING: at drivers/misc/kgdbts.c:730 run_simple_test+0x151/0x2c0()
[...oops clipped...]
This commit re-orders the running of the tests and puts the RODATA
check into its own function so as to correctly avoid the kernel oops
by detecting and using the hw breakpoints.
Cc: <stable@vger.kernel.org> # >= 2.6.26
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
|
| |\ \ \
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
asm/system.h is a cause of circular dependency problems because it contains
commonly used primitive stuff like barrier definitions and uncommonly used
stuff like switch_to() that might require MMU definitions.
asm/system.h has been disintegrated by this point on all arches into the
following common segments:
(1) asm/barrier.h
Moved memory barrier definitions here.
(2) asm/cmpxchg.h
Moved xchg() and cmpxchg() here. #included in asm/atomic.h.
(3) asm/bug.h
Moved die() and similar here.
(4) asm/exec.h
Moved arch_align_stack() here.
(5) asm/elf.h
Moved AT_VECTOR_SIZE_ARCH here.
(6) asm/switch_to.h
Moved switch_to() here.
Signed-off-by: David Howells <dhowells@redhat.com>
|
| |\ \ \
| |/ /
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull "ARM: device tree work" from Arnd Bergmann:
"Most of these patches convert code from using static platform data to
describing the hardware in the device tree. This is only the first
half of the changes for v3.4 because a lot of patches for this topic
came in the last week before the merge window.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up trivial conflicts in arch/arm/mach-vexpress/{Kconfig,core.h}
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (86 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ASoC: DT: Add digital microphone binding to PAZ00 board.
ARM: dt: Add ARM PMU to tegra*.dtsi
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Some SoC have a 32 bit variant of Timer Counter Blocks. We do not
need the chaining of two 16 bit counters anymore for them.
The SoC nature is deduced from the device tree "compatible" string.
For non-device-tree configurations, backward compatibility is maintained
by using the default 16 bit counter configuration.
This patch addresses both the atmel_tclib and its user: tcb_clksrc
clocksource.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Device tree support added to atmel_tclib: the generic Timer Counter
library. This is used by the clocksource/clockevent driver tcb_clksrc.
The current DT enabled platforms are also modified to use it:
- .dtsi files are modified to add Timer Counter Block entries
- alias are created to allow identification of each block
- clkdev lookup tables are added for clocks identification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Requesting iomem region and ioremaping is now done using
the resource size specified instead of a constant value.
Each <SoC>_device.c file is modified accordingly to reflect
actual user interface size.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When the system is under heavy load, we occasionally saw a problem where
the system would get a legitimate interrupt when they should be
disabled.
This was caused by the data_dma_cb() DMA callback unconditionally
re-enabling FPGA interrupts even when data dumping is disabled. When
data dumping was re-enabled, the irq handler would fire while a DMA was
in progress. The "BUG_ON(priv->inflight != NULL);" during the second
invocation of the DMA callback caused the system to crash.
To fix the issue, the priv->enabled boolean is moved under the
protection of the priv->lock spinlock. The DMA callback checks the
boolean to know whether to re-enable FPGA interrupts before it returns.
Now that it is fixed, the driver keeps FPGA interrupts disabled when it
expects that they are disabled, fixing the bug.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| | |/ /
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Lockdep occasionally complains with the message:
INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
This is caused by calling videobuf_dma_unmap() under spin_lock_irq(). To
fix the warning, we drop the lock before unmapping and freeing the
buffer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
|
| | | | |
| | | |
| | | |
| | | | |
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| | | | |
| | | |
| | | |
| | | | |
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| | | |/
| |/|
| | |
| | | |
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Pull TTY/serial patches from Greg KH:
"tty and serial merge for 3.4-rc1
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty
layer, and a number of patches from Alan to help try to wrestle the vt
layer into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog."
* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
serial: pxa: add clk_prepare/clk_unprepare calls
TTY: Wrong unicode value copied in con_set_unimap()
serial: PL011: clear pending interrupts
serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
vt: NULL dereference in vt_do_kdsk_ioctl()
tty: serial: vt8500: fix annotations for probe/remove
serial: remove back and forth conversions in serial_out_sync
serial: use serial_port_in/out vs serial_in/out in 8250
serial: introduce generic port in/out helpers
serial: reduce number of indirections in 8250 code
serial: delete useless void casts in 8250.c
serial: make 8250's serial_in shareable to other drivers.
serial: delete last unused traces of pausing I/O in 8250
pch_uart: Add module parameter descriptions
pch_uart: Use existing default_baud in setup_console
pch_uart: Add user_uartclk parameter
pch_uart: Add Fish River Island II uart clock quirks
pch_uart: Use uartclk instead of base_baud
mpc5200b/uart: select more tolerant uart prescaler on low baudrates
tty: moxa: fix bit test in moxa_start()
...
|
