aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/md/md.c
Commit message (Collapse)AuthorAge
* [PATCH] md: avoid backward event updates in md superblock when degraded.NeilBrown2006-08-27
| | | | | | | | | | | | | | | | | | | | | If we - shut down a clean array, - restart with one (or more) drive(s) missing - make some changes - pause, so that they array gets marked 'clean', the event count on the superblock of included drives will be the same as that of the removed drives. So adding the removed drive back in will cause it to be included with no resync. To avoid this, we only update the eventcount backwards when the array is not degraded. In this case there can (should) be no non-connected drives that we can get confused with, and this is the particular case where updating-backwards is valuable. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: fix oops in error-handlingAndrew Morton2006-07-10
| | | | | | | | | During early MD setup (superblock reading), we don't have a personality yet. But the error-handling code tries to dereference mddev->pers. Fix. Acked-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: require CAP_SYS_ADMIN for (re-)configuring md devices via sysfsNeilBrown2006-07-10
| | | | | | | | | | | | The ioctl requires CAP_SYS_ADMIN, so sysfs should too. Note that we don't require CAP_SYS_ADMIN for reading attributes even though the ioctl does. There is no reason to limit the read access, and much of the information is already available via /proc/mdstat Cc: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: unify usage of symbolic names for permsNeilBrown2006-07-10
| | | | | | | | | | | Some places we use number (0660) someplaces names (S_IRUGO). Change all numbers to be names, and change 0655 to be what it should be. Also make some formatting more consistent. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: fix resync speed calculation for restarted resyncsNeilBrown2006-07-10
| | | | | | | | | | | | | | | | | | We introduced 'io_sectors' recently so we could count the sectors that causes io during resync separate from sectors which didn't cause IO - there can be a difference if a bitmap is being used to accelerate resync. However when a speed is reported, we find the number of sectors processed recently by subtracting an oldish io_sectors count from a current 'curr_resync' count. This is wrong because curr_resync counts all sectors, not just io sectors. So, add a field to mddev to store the curren io_sectors separately from curr_resync, and use that in the calculations. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: delay starting md threads until array is completely setupNeilBrown2006-07-10
| | | | | | | | | | | | | | | | When an array is started we start one or two threads (two if there is a reshape or recovery that needs to be completed). We currently start these *before* the array is completely set up and in particular before queue->queuedata is set. If the thread actually starts very quickly on another CPU, we can end up dereferencing queue->queuedata and oops. This patch also makes sure we don't try to start a recovery if a reshape is being restarted. Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: set desc_nr correctly for version-1 superblocksNeilBrown2006-07-10
| | | | | | | | | | | | This has to be done in ->load_super, not ->validate_super Without this, hot-adding devices to an array doesn't always work right - though there is a work around in mdadm-2.5.2 to make this less of an issue. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] lockdep: annotate blkdev nestingIngo Molnar2006-07-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teach special (recursive) locking code to the lock validator. Effects on non-lockdep kernels: - the introduction of the following function variants: extern struct block_device *open_partition_by_devnum(dev_t, unsigned); extern int blkdev_put_partition(struct block_device *); static int blkdev_get_whole(struct block_device *bdev, mode_t mode, unsigned flags); which on non-lockdep are the same as open_by_devnum(), blkdev_put() and blkdev_get(). - a subclass parameter to do_open(). [unused on non-lockdep] - a subclass parameter to __blkdev_put(), which is a new internal function for the main blkdev_put*() functions. [parameter unused on non-lockdep kernels, except for two sanity check WARN_ON()s] these functions carry no semantical difference - they only express object dependencies towards the lockdep subsystem. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: Neil Brown <neilb@cse.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Remove obsolete #include <linux/config.h>Jörn Engel2006-06-30
| | | | | Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
* [PATCH] devfs: Remove the gendisk devfs_name field as it's no longer neededGreg Kroah-Hartman2006-06-26
| | | | | | | And remove the now unneeded number field. Also fixes all drivers that set these fields. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] devfs: Remove the devfs_fs_kernel.h file from the treeGreg Kroah-Hartman2006-06-26
| | | | | | Also fixes up all files that #include it. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] devfs: Remove devfs_remove() function from the kernel treeGreg Kroah-Hartman2006-06-26
| | | | | | Removes the devfs_remove() function and all callers of it. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] devfs: Remove devfs_mk_bdev() function from the kernel treeGreg Kroah-Hartman2006-06-26
| | | | | | Removes the devfs_mk_bdev() function and all callers of it. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] devfs: Remove devfs_mk_dir() function from the kernel treeGreg Kroah-Hartman2006-06-26
| | | | | | Removes the devfs_mk_dir() function and all callers of it. Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] drivers/md/md.c: make code staticAdrian Bunk2006-06-26
| | | | | | | | | Make needlessly global code static. Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Allow the write_mostly flag to be set via sysfsNeilBrown2006-06-26
| | | | | | | | | | It appears in /sys/mdX/md/dev-YYY/state and can be set or cleared by writing 'writemostly' or '-writemostly' respectively. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Allow resync_start to be set and queried via sysfsNeilBrown2006-06-26
| | | | | | Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Allow raid 'layout' to be read and set via sysfsNeilBrown2006-06-26
| | | | | | Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Allow rdev state to be set via sysfsNeilBrown2006-06-26
| | | | | | | | | | | The md/dev-XXX/state file can now be written: "faulty" simulates an error on the device "remove" removes the device from the array (if it is not busy) Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Set/get state of array via sysfsNeilBrown2006-06-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows the state of an md/array to be directly controlled via sysfs and adds the ability to stop and array without tearing it down. Array states/settings: clear No devices, no size, no level Equivalent to STOP_ARRAY ioctl inactive May have some settings, but array is not active all IO results in error When written, doesn't tear down array, but just stops it suspended (not supported yet) All IO requests will block. The array can be reconfigured. Writing this, if accepted, will block until array is quiescent readonly no resync can happen. no superblocks get written. write requests fail read-auto like readonly, but behaves like 'clean' on a write request. clean - no pending writes, but otherwise active. When written to inactive array, starts without resync If a write request arrives then if metadata is known, mark 'dirty' and switch to 'active'. if not known, block and switch to write-pending If written to an active array that has pending writes, then fails. active fully active: IO and resync can be happening. When written to inactive array, starts with resync write-pending (not supported yet) clean, but writes are blocked waiting for 'active' to be written. active-idle like active, but no writes have been seen for a while (100msec). Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Don't write dirty/clean update to spares - leave them aloneNeilBrown2006-06-26
| | | | | | | | | | | | | | | | | | | | | | | - record the 'event' count on each individual device (they might sometimes be slightly different now) - add a new value for 'sb_dirty': '3' means that the super block only needs to be updated to record a clean<->dirty transition. - Prefer odd event numbers for dirty states and even numbers for clean states - Using all the above, don't update the superblock on a spare device if the update is just doing a clean-dirty transition. To accomodate this, a transition from dirty back to clean might now decrement the events counter if nothing else has changed. The net effect of this is that spare drives will not see any IO requests during normal running of the array, so they can go to sleep if that is what they want to do. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Allow re-add to work on array without bitmapsNeilBrown2006-06-26
| | | | | | | | | | | | | | | | | | When an array has a bitmap, a device can be removed and re-added and only blocks changes since the removal (as recorded in the bitmap) will be resynced. It should be possible to do a similar thing to arrays without bitmaps. i.e. if a device is removed and re-added and *no* changes have been made in the interim, then the add should not require a resync. This patch allows that option. This means that when assembling an array one device at a time (e.g. during device discovery) the array can be enabled read-only as soon as enough devices are available, but extra devices can still be added without causing a resync. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md/bitmap: tidy up i_writecount handling in md/bitmapNeilBrown2006-06-26
| | | | | | | | | | | | md/bitmap modifies i_writecount of a bitmap file to make sure that no-one else writes to it. The reverting of the change is sometimes done twice, and there is one error path where it is omitted. This patch tidies that up. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md/bitmap: fix online removal of file-backed bitmapsNeilBrown2006-06-26
| | | | | | | | | | | | When "mdadm --grow /dev/mdX --bitmap=none" is used to remove a filebacked bitmap, the bitmap was disconnected from the array, but the file wasn't closed (until the array was stopped). The file also wasn't closed if adding the bitmap file failed. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: make md_print_devices() staticAdrian Bunk2006-06-26
| | | | | | | | | This patch makes the needlessly global md_print_devices() static. Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: allow a linear array to have drives added while activeNeilBrown2006-06-26
| | | | | | Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: allow checkpoint of recovery with version-1 superblockNeilBrown2006-06-26
| | | | | | | | | | | | | For a while we have had checkpointing of resync. The version-1 superblock allows recovery to be checkpointed as well, and this patch implements that. Due to early carelessness we need to add a feature flag to signal that the recovery_offset field is in use, otherwise older kernels would assume that a partially recovered array is in fact fully recovered. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: remove nuisance message at shutdownNeilBrown2006-06-26
| | | | | | | | | | | At shutdown, we switch all arrays to read-only, which creates a message for every instantiated array, even those which aren't actually active. So remove the message for non-active arrays. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: increase the delay before marking metadata clean, and make it ↵NeilBrown2006-06-26
| | | | | | | | | | | | | configurable When a md array has been idle (no writes) for 20msecs it is marked as 'clean'. This delay turns out to be too short for some real workloads. So increase it to 200msec (the time to update the metadata should be a tiny fraction of that) and make it sysfs-configurable. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: remove useless ioctl warningNeilBrown2006-06-26
| | | | | | | | | | This warning was slightly useful back in 2.2 days, but is more an annoyance now. It makes it awkward to add new ioctls (that we we are likely to do that in the current climate, but it is possible). Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Fix badness in sysfs_notify caused by md_new_eventNeilBrown2006-05-31
| | | | | | | | | | | | | | | | | | | | | From: NeilBrown <neilb@suse.de> If an error is reported by a drive in a RAID array (which is done via bi_end_io - in interrupt context), we call md_error and md_new_event which calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be called in interrupt context. This patch just creates a variant of md_new_event which avoids the sysfs call, and uses that. A better fix for later is to arrange for the event to be called from user-context. Note: avoiding the sysfs call isn't a problem as an error will not, by itself, modify the sync_action attribute. (We do still need to wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat). Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Unlock md devices when stopping them on reboot.Neil Brown2006-05-26
| | | | | | | otherwise we get nasty messages about locks not being released. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Fix inverted test for 'repair' directive.NeilBrown2006-05-21
| | | | | | | | | We should be able to write 'repair' to /sys/block/mdX/md/sync_action, however due to and inverted test, that always given EINVAL. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: locking fixIngo Molnar2006-04-20
| | | | | | | | | | | | - fix mddev_lock() usage bugs in md_attr_show() and md_attr_store(). [they did not anticipate the possibility of getting a signal] - remove mddev_lock_uninterruptible() [unused] Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sysfs: Allow sysfs attribute files to be pollableNeilBrown2006-04-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | It works like this: Open the file Read all the contents. Call poll requesting POLLERR or POLLPRI (so select/exceptfds works) When poll returns, close the file and go to top of loop. or lseek to start of file and go back to the 'read'. Events are signaled by an object manager calling sysfs_notify(kobj, dir, attr); If the dir is non-NULL, it is used to find a subdirectory which contains the attribute (presumably created by sysfs_create_group). This has a cost of one int per attribute, one wait_queuehead per kobject, one int per open file. The name "sysfs_notify" may be confused with the inotify functionality. Maybe it would be nice to support inotify for sysfs attributes as well? This patch also uses sysfs_notify to allow /sys/block/md*/md/sync_action to be pollable Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] md: Remove some code that can sleep from under a spinlockNeilBrown2006-03-31
| | | | | | | | And remove the comments that were put in inplace of a fix too.... Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Convert reconfig_sem to reconfig_mutexNeilBrown2006-03-27
| | | | | | | | ... being careful that mutex_trylock is inverted wrt down_trylock Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sem2mutex: drivers/mdArjan van de Ven2006-03-27
| | | | | | | | | | | | | Semaphore to mutex conversion. The conversion was generated via scripts, and the result was validated automatically via a script as well. Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Neil Brown <neilb@cse.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Fix md grow/size code to correctly find the maximum available spaceNeilBrown2006-03-27
| | | | | | | | | | | | | An md array can be asked to change the amount of each device that it is using, and in particular can be asked to use the maximum available space. This currently only works if the first device is not larger than the rest. As 'size' gets changed and so 'fit' becomes wrong. So check if a 'fit' is required early and don't corrupt it. Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Support suspending of IO to regions of an md arrayNeilBrown2006-03-27
| | | | | | | | | | | | | | | | | This allows user-space to access data safely. This is needed for raid5 reshape as user-space needs to take a backup of the first few stripes before allowing reshape to commence. It will also be useful in cluster-aware raid1 configurations so that all cluster members can leave a section of the array untouched while a resync/recovery happens. A 'start' and 'end' of the suspended range are written to 2 sysfs attributes. Note that only one range can be suspended at a time. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Make 'reshape' a possible sync_action actionNeilBrown2006-03-27
| | | | | | | | | This allows reshape to be triggerred via sysfs (which is the only way to start it happening). Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Split reshape handler in check_reshape and start_reshapeNeilBrown2006-03-27
| | | | | | | | | | check_reshape checks validity and does things that can be done instantly - like adding devices to raid1. start_reshape initiates a restriping process to convert the whole array. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Checkpoint and allow restart of raid5 reshapeNeilBrown2006-03-27
| | | | | | | | | | | | | | | | | | | We allow the superblock to record an 'old' and a 'new' geometry, and a position where any conversion is up to. The geometry allows for changing chunksize, layout and level as well as number of devices. When using verion-0.90 superblock, we convert the version to 0.91 while the conversion is happening so that an old kernel will refuse the assemble the array. For version-1, we use a feature bit for the same effect. When starting an array we check for an incomplete reshape and restart the reshape process if needed. If the reshape stopped at an awkward time (like when updating the first stripe) we refuse to assemble the array, and let user-space worry about it. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Final stages of raid5 expand codeNeilBrown2006-03-27
| | | | | | | | | | | | | | | | This patch adds raid5_reshape and end_reshape which will start and finish the reshape processes. raid5_reshape is only enabled in CONFIG_MD_RAID5_RESHAPE is set, to discourage accidental use. Read the 'help' for the CONFIG_MD_RAID5_RESHAPE entry. and Make sure that you have backups, just in case. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Core of raid5 resize processNeilBrown2006-03-27
| | | | | | | | | | | | | | | | | | | | | | This patch provides the core of the resize/expand process. sync_request notices if a 'reshape' is happening and acts accordingly. It allocated new stripe_heads for the next chunk-wide-stripe in the target geometry, marking them STRIPE_EXPANDING. Then it finds which stripe heads in the old geometry can provide data needed by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to read all blocks on those stripes. Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then is written out and released. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Allow stripes to be expanded in preparation for expanding an arrayNeilBrown2006-03-27
| | | | | | | | | | | | | | | | | | | Before a RAID-5 can be expanded, we need to be able to expand the stripe-cache data structure. This requires allocating new stripes in a new kmem_cache. If this succeeds, we copy cache pages over and release the old stripes and kmem_cache. We then allocate new pages. If that fails, we leave the stripe cache at it's new size. It isn't worth the effort to shrink it back again. Unfortuanately this means we need two kmem_cache names as we, for a short period of time, we have two kmem_caches. So they are raid5/%s and raid5/%s-alt Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Update status_resync to handle LARGE devicesNeilBrown2006-03-27
| | | | | | | | | | status_resync - used by /proc/mdstat to report the status of a resync, assumes that device sizes will always fit into an 'unsigned long' This is no longer the case... Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Fix the 'failed' count for version-0 superblocksNeilBrown2006-03-27
| | | | | | | | | | | We are counting failed devices twice, once of the device that is failed, and once for the hole that has been left in the array. Remove the former so 'failed' matches 'missing'. Storing these counts in the superblock is a bit silly anyway.... Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Add '4' to the list of levels for which bitmaps are supportedNeilBrown2006-03-27
| | | | | | | | I really should make this a function of the personality.... Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] md: Make sure QUEUE_FLAG_CLUSTER is set properly for md.NeilBrown2006-03-27
| | | | | | | | | This flag should be set for a virtual device iff it is set for all underlying devices. Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-14 01:36:45 -0500