| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
NFS/RDMA currently fails to set up connections if peer2peer is on.
This is due to the fact that the NFS/RDMA client sets its ORD to 0.
If peer2peer is set, make sure the active side ORD is >= 1 and the
passive side IRD is >=1.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add support for new SFP+ PHY
RDMA/nes: Add wide_ppm_offset parm for switch compatibility
RDMA/nes: Fix SFP+ PHY initialization
RDMA/nes: Fix nes_nic_cm_xmit() error handling
RDMA/nes: Fix error handling issues
RDMA/nes: Fix incorrect casts on 32-bit architectures
IPoIB: Document newish features
RDMA/cma: Create cm id even when IB port is down
RDMA/cma: Use rate from IPoIB broadcast when joining IPoIB multicast groups
IPoIB: Avoid free_netdev() BUG when destroying a child interface
mlx4_core: Don't leak mailbox for SET_PORT on Ethernet ports
RDMA/cxgb3: Release dependent resources only when endpoint memory is freed.
RDMA/cxgb3: Handle EEH events
IB/mlx4: Use pgprot_writecombine() for BlueFlame pages
|
| | |\ \ \ \ |
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Add new register settings for new SFP+ PHY/firmware.
Add new PHY to to nes_netdev_get/set_settings.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We have observed unstable link with a new BNT switch.
Add wide_ppm_offset parameter to allow the user to control the clock
ppm offset on the CX4 interface for better compatibility. Default is
100ppm, setting it to 1 will increase it to 300ppm. Change default
SerDes1 reference clock to external source.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
SFP+ PHY initialization has very long delays, incorrect settings for
direct attach copper cables, and inconsistent link detection.
Adjust delays to the minimum required by the PHY. Worst case is now
less than 4 seconds. Add new register settings for direct attach
cables. Change link detection logic to use two new registers for more
consistent link state detection. Reorganize code to shorten line
length.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We are getting crash or hung situation when we are running network
cable pull tests during RDMA traffic.
In schedule_nes_timer(), we return an error if nes_nic_cm_xmit()
returns failure. This is changed to success as skb is being put on
the timer routines to be processed later. In send_syn() case, we are
indicating connect failure once from nes_connect() and the other when
the rexmit retries expires.
The other issue is skb->users which we are incrementing before calling
nes_nic_cm_xmit() which calls dev_queue_xmit() but in case of failure
we are decrementing the skb->users at the same time putting the skb on
the rexmit path. Even if dev_queue_xmit() fails, the skb->users is
decremented already. We are removing the decrement of skb->users in
case of failure from both schedule_nes_timer() as well as from
nes_cm_timer_tick().
There is also extra check in nes_cm_timer_tick() for rexmit failure
which does a break from the loop is removed. This causes problem as
the other nodes have their cm_node->ref_count incremented and are not
processed.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Fix issues found by static code analysis:
(1) Check if cm_node was successfully created for loopback connection.
(2) schedule_nes_timer() does not free up allocated memory after
encountering an error. There is a WARN_ON() for this condition.
(3) there is a cm_node->freed flag which is set but not used.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The were some incorrect casts to unsigned long that caused 64-bit values
to be truncated on 32-bit architectures and made the driver pass invalid
adresses and lengths to the hardware. The problems were primarily seen
with kernels with highmem configured but some could show up in
non-highmem kernels, too.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | |/
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The PAT work on x86 has finally made pgprot_writecombine() a usable API
for modular drivers. As the comment indicates, this is exactly what we
want to use in mlx4_ib to map BlueFlame pages up to userspace, since
using WC for these pages improves small message latency significantly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | |/
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
We have to release the RTNL before calling free_netdev() so that the
device state has a chance to become NETREG_UNREGISTERED. Otherwise
when removing a child interface, we hit the BUG() that tests the
device state in free_netdev().
Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The cxgb3 l2t entry, hwtid, and dst entry were being released before
all the iwch_ep references were released. This can cause a crash in
t3_l2t_send_slow() and other places where the l2t entry is used.
The fix is to defer releasing these resources until all endpoint
references are gone.
Details:
- move flags field to the iwch_ep_common struct.
- add a flag indicating resources are to be released.
- release resources at endpoint free time instead of close/abort time.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
- wrap calls into cxgb3 and fail them if we're in the middle
of a PCI EEH event.
- correctly unwind and release endpoint and other resources when
we are in an EEH event.
- dispatch IB_EVENT_DEVICE_FATAL event when cxgb3 notifies iw_cxgb3 of
a fatal error.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When doing rdma_resolve_addr(), if the relevant IB port is down, the
function fails and the cm_id is not bound to the correct device.
Therefore, application does not have a device handle and cannot wait
for the port to become active. The function fails because the
underlying IPoIB interface is not joined to the broadcast group and
therefore the SA does not have a multicast record to take a Q_Key
from.
The fix is to use lazy Q_Key resolution - cma_set_qkey() will set
id_priv->qkey if it was not set, and will be called just before the
Q_Key is really required.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When joining an IPoIB multicast group, use the same rate as in the
broadcast group. Otherwise, if the RDMA CM creates this group before
IPoIB does, it might get a different rate. This will cause IPoIB to
fail joining to the same group later on, because IPoIB uses strict
rate selection.
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \
| |/
|/|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (119 commits)
[SCSI] scsi_dh_rdac: Retry for NOT_READY check condition
[SCSI] mpt2sas: make global symbols unique
[SCSI] sd: Make revalidate less chatty
[SCSI] sd: Try READ CAPACITY 16 first for SBC-2 devices
[SCSI] sd: Refactor sd_read_capacity()
[SCSI] mpt2sas v00.100.11.15
[SCSI] mpt2sas: add MPT2SAS_MINOR(221) to miscdevice.h
[SCSI] ch: Add scsi type modalias
[SCSI] 3w-9xxx: add power management support
[SCSI] bsg: add linux/types.h include to bsg.h
[SCSI] cxgb3i: fix function descriptions
[SCSI] libiscsi: fix possbile null ptr session command cleanup
[SCSI] iscsi class: remove host no argument from session creation callout
[SCSI] libiscsi: pass session failure a session struct
[SCSI] iscsi lib: remove qdepth param from iscsi host allocation
[SCSI] iscsi lib: have lib create work queue for transmitting IO
[SCSI] iscsi class: fix lock dep warning on logout
[SCSI] libiscsi: don't cap queue depth in iscsi modules
[SCSI] iscsi_tcp: replace scsi_debug/tcp_debug logging with iscsi conn logging
[SCSI] libiscsi_tcp: replace tcp_debug/scsi_debug logging with session/conn logging
...
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We do not need to have llds set the host no for the session's
parent, because we know the session's parent is going to be
the host. This removes it from the session creation callback
and converts the drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The qdepth setting was useful when we needed libiscsi to verify
the setting. Now we just need to make sure if older tools
passed in zero then we need to set some default.
So this patch just has us use the sht->cmd_per_lun or if
for LLD does a host per session then we can set it on per
host basis.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We were using the shost work queue which ended up being
a little akward since all iscsi hosts need a thread for
scanning, but only drivers hooked into libiscsi need
a workqueue for transmitting. So this patch moves the
xmit workqueue to the lib.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
There is no need to cap the queue depth in the modules. We set
this in userspace and can do that there. For performance testing
with ram based targets, this is helpful since we can have very
high queue depths.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
iser has its own logging inrfastrucutre. Convert it to use
it instead of libiscsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When net-next and infiniband were merged upstream, each branch deleted
one of a pair of adjacent lines from nes_nic.c, but when Linus fixed the
conflict up, he brought back both of the lines. Fix up to the intended
final tree state.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (26 commits)
posix timers: fix RLIMIT_CPU && fork()
time: ntp: fix bug in ntp_update_offset() & do_adjtimex(), fix
time: ntp: clean up second_overflow()
time: ntp: simplify ntp_tick_adj calculations
time: ntp: make 64-bit constants more robust
time: ntp: refactor do_adjtimex() some more
time: ntp: refactor do_adjtimex()
time: ntp: fix bug in ntp_update_offset() & do_adjtimex()
time: ntp: micro-optimize ntp_update_offset()
time: ntp: simplify ntp_update_offset_fll()
time: ntp: refactor and clean up ntp_update_offset()
time: ntp: refactor up ntp_update_frequency()
time: ntp: clean up ntp_update_frequency()
time: ntp: simplify the MAX_TICKADJ_SCALED definition
time: ntp: simplify the second_overflow() code flow
time: ntp: clean up kernel/time/ntp.c
x86: hpet: stop HPET_COUNTER when programming periodic mode
x86: hpet: provide separate functions to stop and start the counter
x86: hpet: print HPET registers during setup (if hpet=verbose is used)
time: apply NTP frequency/tick changes immediately
...
|
| | | \ | |
| | | \ | |
| | |\ \|
| | | |
| | | |
| | | | |
timers/core
|
| | | |/
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Impact: new timer API
Based on an idea from Martin Josefsson with the help of
Patrick McHardy and Stephen Hemminger:
introduce the mod_timer_pending() API which is a mod_timer()
offspring that is an invariant on already removed timers.
(regular mod_timer() re-activates non-pending timers.)
This is useful for the networking code in that it can
allow unserialized mod_timer_pending() timer-forwarding
calls, but a single del_timer*() will stop the timer
from being reactivated again.
Also while at it:
- optimize the regular mod_timer() path some more, the
timer-stat and a debug check was needlessly duplicated
in __mod_timer().
- make the exports come straight after the function, as
most other exports in timer.c already did.
- eliminate __mod_timer() as an external API, change the
users to mod_timer().
The regular mod_timer() code path is not impacted
significantly, due to inlining optimizations and due to
the simplifications.
Based-on-patch-from: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
|
| | |\| |
| | | |
| | | |
| | | |
| | | | |
Conflicts:
drivers/net/wimax/i2400m/usb-notif.c
|
| | | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Also, removed unnecessary memset() since alloc_netdev returns
zeroed memory.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Convert this driver to new net_device_ops infrastructure.
Also use default net_device get-stats infrastructure
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Freeze activity when notified that the underlying chip
is getting reset on a EEH event or fatal error.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
RDMA/cxgb3: Enforce required firmware
IB/mlx4: Unregister IB device prior to CLOSE PORT command
mlx4_core: Add link type autosensing
mlx4_core: Don't perform SET_PORT command for Ethernet ports
RDMA/nes: Handle MPA Reject message properly
RDMA/nes: Improve use of PBLs
RDMA/nes: Remove LLTX
RDMA/nes: Inform hardware that asynchronous event has been handled
RDMA/nes: Fix tmp_addr compilation warning
RDMA/nes: Report correct vendor_id and vendor_part_id
RDMA/nes: Update copyright to new legal entity and year
RDMA/nes: Account for freed PBL after HW operation
IB: Remove useless ibdev_is_alive() tests from sysfs code
IB/sa_query: Fix AH leak due to update_sm_ah() race
IB/mad: Fix ib_post_send_mad() returning 0 with no generate send comp
IB/mad: initialize mad_agent_priv before putting on lists
IB/mad: Fix null pointer dereference in local_completions()
IB/mad: Fix RMPP header RRespTime manipulation
IB/iser: Remove hard setting of path MTU
mlx4_core: Add device IDs for MT25458 10GigE devices
...
|
| | | | | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | | \ | |
| | |\ \ \ \ \ \ \ \ \ \ \
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | | |
'mlx4', 'mthca', 'nes' and 'sysfs' into for-next
|
| | | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | |
| | | | | | | | | | | | | |
Some attribute show functions test ibdev_is_alive() to make sure that
it's OK to access device state. However, the sysfs attributes will
not be registered until the device is fully initialized, and they'll
be unregistered before anything is torn down, so ibdev_is_alive()
doesn't do anything useful. Remove it.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |/
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Move the ib_device_unregister_sysfs() call from ib_dealloc_device() to
ib_unregister_device(). The old code allows device unregister to
proceed even if some sysfs files are open, which leaves a window where
userspace can open a file before a device is removed but then end up
reading the file after the device is removed, which leads to various
kernel crashes either because the device data structure is freed or
because the low-level driver code is gone after module removal.
By not returning from ib_unregister_device() until after all sysfs
entries are removed, we make sure that data structures and/or module
code is not freed until after all sysfs access is done.
Reported-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
While doing testing, there are failures as MPA Reject call is not
handled. To handle MPA Reject call, following changes are done:
*Handle inbound/outbound MPA Reject response message.
When nes_reject() is called for pending MPA request reply,
send the MPA Reject message to its peer (active
side)cm_node. The peer cm_node (active side) will indicate
Reject message event for the pending Connect Request.
*Handle MPA Reject response message for loopback connections and listener.
When MPA Request is rejected, check if it is a loopback
connection and if it is then it will send Reject message event
to its peer loopback node. Also when destroying listener,
check if the cm_nodes for that listener are loopback or not.
*Add gracefull connection close with the MPA Reject response message.
Send gracefull close (FIN, FIN ACK..) to terminate the cm_nodes.
*Some code re-org while making the above changes.
Removed recv_list and recv_list_lock from the cm_node
structure as there can be only one receive close entry on the
timer. Also implemented handle_recv_entry() as receive close
entry is processed from both nes_rem_ref_cm_node() as well as
nes_cm_timer_tick().
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Two level 256 byte PBLs was not implemented so the driver could report
out of memory when in fact there were PBLs still available.
This solution prefers to use 4KB PBLs over two level 256B PBLs until
the number of 4KB PBLs falls below a threshold. At this point the 4KB
PBL structure is converted to use 256B PBLs which prevents the driver
from running out of 4KB PBLs too quickly.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
NETIF_F_LLTX is deprecated. Remove private TX locking from the driver
and remove the NETIF_F_LLTX feature flag. This also fixes a warning
in some configs that comes from doing skb_linearize() call in the
hard_start_xmit method with IRQs disabled (if HIGHMEM is enabled,
skb_linearize() may end up enabling BHs, which is a no-no if hard IRQs
are disabled in that context). By getting rid of LLTX, we do not
disable IRQs when skb_linearize() is called.
Remove the sq_lock as it is not needed for non-LLTX. Fix ethtool not
to show the counter for sq_lock.
Reported-by: aluno3@poczta.onet.pl
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
When asynchronous events are processed by software, it is necessary
to let the hardware know that software has handled the event. This
frees up the entry in the asynchronous event queue.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
In find_node(), tmp_addr causes an "unused variable" warning when
INFINIBAND_NES_DEBUG is not defined. It's only used in a nes_debug()
and the print does not make sense. So take out the whole thing.
Reported-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
ibv_devinfo displays 0 for vendor_id and vendor_part_id. Fill in OUI
and device_id for those two fields.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | |
| | | | | | | | | | | | |
Update copyright to the new legal entity, Intel-NE, Inc., an Intel
company. Update copyright for the new year.
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | | |/
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | |
| | | | | | | | | | | |
Fix occurrences where the software PBL counts were changed before the
hardware was updated. This bug allowed another thread to overallocate
the hardware resources.
Add proper PBL accounting in case nes_reg_mr() fails.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | |/
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
When snooping a PortInfo MAD, its client_reregister bit is checked.
If the bit is ON then a CLIENT_REREGISTER event is dispatched,
otherwise a LID_CHANGE event is dispatched. This way of decision
ignores the cases where the MAD changes the LID along with an
instruction to reregister (so a necessary LID_CHANGE event won't be
dispatched) or the MAD is neither of these (and an unnecessary
LID_CHANGE event will be dispatched).
This causes problems at least with IPoIB, which will do a "light"
flush on reregister, rather than the "heavy" flush required due to a
LID change.
Fix this by dispatching a CLIENT_REREGISTER event if the
client_reregister bit is set, but also compare the LID in the MAD to
the current LID. If and only if they are not identical then a
LID_CHANGE event is dispatched.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | |
| | | | | | | | | | |
According to the ConnectX programmer's reference manual, all
operations should be stopped, all QPs should be torn down and all WQEs
flushed before the CLOSE_PORT command is invoked. In some cases
reversing the order of operations (as implemented now) could cause
a loss of completions.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | | |/
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | |
| | | | | | | | | |
When snooping a PortInfo MAD, its client_reregister bit is checked.
If the bit is ON then a CLIENT_REREGISTER event is dispatched,
otherwise a LID_CHANGE event is dispatched. This way of decision
ignores the cases where the MAD changes the LID along with an
instruction to reregister (so a necessary LID_CHANGE event won't be
dispatched) or the MAD is neither of these (and an unnecessary
LID_CHANGE event will be dispatched).
This causes problems at least with IPoIB, which will do a "light"
flush on reregister, rather than the "heavy" flush required due to a
LID change.
Fix this by dispatching a CLIENT_REREGISTER event if the
client_reregister bit is set, but also compare the LID in the MAD to
the current LID. If and only if they are not identical then a
LID_CHANGE event is dispatched.
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| | | | | | | | |/
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Our testing uncovered a race condition in ib_sa_event():
spin_lock_irqsave(&port->ah_lock, flags);
if (port->sm_ah)
kref_put(&port->sm_ah->ref, free_sm_ah);
port->sm_ah = NULL;
spin_unlock_irqrestore(&port->ah_lock, flags);
schedule_work(&sa_dev->port[event->element.port_num -
sa_dev->start_port].update_task);
If two events occur back-to-back (e.g., client-reregister and LID
change), both may pass the spinlock-protected code above before the
scheduled work updates the port->sm_ah handle. Then if the scheduled
work ends up running twice, the second operation will then find a
non-NULL port->sm_ah, and will simply overwrite it in update_sm_ah --
resulting in an AH leak.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
