| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit 8d4548f2b ("IB/qib: Default some module parameters optimally")
introduced an issue with older root complexes. They cannot handle the
pcie_caps of 0x51 (MaxReadReq 4096, MaxPayload=256).
A typical diagnostic in this situation reported by syslog contains
the text:
[PCIe Poisoned TLP][Send DMA memory read]
Restore the module paramter default to zero with will avoid any
changes in the root complex.
Reviewed-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Minimize the need for users to have to set module parameters to get
good performance.
The following two parameters are changed:
- rcvhdrcnt to twice the rcvegrcnt
- pcie_caps=0x51
The rcvhdrcnt at twice the egrcount allows the preemptive NAK code
during reception to function in 100% of the cases rather than a sender
jiffies-based timeout.
The pcie_caps default of 0x51 will set the proposed MaxPayload and
MaxReceiveReqest to 256 and 4096 respectively. The capabilities on
the root complex will be used to limit those values.
Reviewed-by: Ram Vepa <ram.vepa@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| |
|
|
|
|
|
|
| |
They had been getting it implicitly via device.h but we can't
rely on that for the future, due to a pending cleanup so fix
it now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
| |
|
|
|
|
|
|
|
|
| |
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| |
|
|
|
|
|
|
|
|
| |
The driver reads PCI revision ID from the PCI configuration register
while it's already stored by PCI subsystem in the revision field of
struct pci_dev.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| |
|
|
|
|
|
| |
Clean up properly if pci_set_consistent_dma_mask() fails.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| |
|
|
|
|
|
|
| |
Some PCIe root complex chip sets don't support advanced error reporting.
Allow the driver to load OK if pci_enable_pcie_error_reporting() fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
| |
|
|
|
|
|
|
| |
Don't set write combining via PAT on the VL15 buffers to avoid a rare
problem with unaligned writes from interrupt-flushed store buffers.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
|
Add a low-level IB driver for QLogic PCIe adapters.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
