aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/ide
Commit message (Collapse)AuthorAge
* alim15x3: remove redundant m5229_revision checkBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | init_dma_ali15x3() guarantees that hwif->dma_base will never be set for m5229_revision < 0x20 so remove redundant m5229_revision >= 0x20 check from init_hwif_common_ali15x3(). While at it remove incorrect comment. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sc1200: fix ->dma_base equal zero handlingBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | Set hwif->atapi_dma/{ultra,mwdma}_mask and drive->autodma after checking that ->dma_base exists. If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks shouldn't be initialized or bad things will happen. OTOH hwif->set_{pio,dma}_mode hooks should be set even if hwif->dma_base == 0. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cs5520: fix ->dma_base equal zero handlingBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | Set hwif->ide_dma_{check,on} and hwif->autodma to 1 after checking that ->dma_base exists. If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks shouldn't be initialized or bad things will happen. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sgiioc4: add missing ->dma_base checkBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks shouldn't be initialized or bad things will happen. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cs5535: add missing ->dma_base checkBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks shouldn't be initialized or bad things will happen. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove CONFIG_IDEDMA_IVB config optionBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | Devices which don't set word 93 validation bit should be now handled by ide-iops.c::ivb_list[] and for debugging purposes cable detection can be completely overriden with "idex=ata66" parameter. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: change master/slave IDENTIFY orderBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | Need to probe slave device first to make it release PDIAG- (this is required for correct device side cable detection). Based on libata commit f31f0cc2f0b7527072d94d02da332d9bb8d7d94c. Thanks to Craig for testing this patch. Cc: Craig Block <chblock3@yahoo.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: move ide_config_drive_speed() calls to upper layers (take 2)Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16. * Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program the host for the transfer mode after programming the device. Set it in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac and via82cxxx host drivers. * Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely skip programming of host/device for the transfer mode ("smart" hosts). Set it in it821x host driver and check it in ide_tune_dma(). * Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all direct ->set_pio_mode/->speedproc users to use these helpers. * Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc methods to callers. * Rename ->speedproc method to ->set_dma_mode, make it void and update all implementations accordingly. * Update ide_set_xfer_rate() comments. * Unexport ide_config_drive_speed(). v2: * Fix issues noticed by Sergei: - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt to setting DMA modes from sc1200_set_pio_mode() to do_special() - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma() - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode() - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode() - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL - don't set ->set_{pio,dma}_mode on it821x in "smart" mode - fix build problem in pmac.c - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c - improve patch description Changes in behavior caused by this patch: - HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change PIO mode if it821x controller is in "smart" mode - removal of two debugging printk-s (from cs5530.c and sc1200.c) - transfer modes 0x00-0x07 passed from user space may be programmed twice on the device (not really an issue since 0x00 is not supported correctly by any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid) Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_new: check ide_config_drive_speed() return valueBartlomiej Zolnierkiewicz2007-10-13
| | | | | Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cs5535: check ide_config_drive_speed() return valueBartlomiej Zolnierkiewicz2007-10-13
| | | | | Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* amd74xx/via82cxxx: check ide_config_drive_speed() return valueBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | * Check ide_config_drive_speed() return value. * While at also call ide_config_drive_speed() if the transfer mode is XFER_PIO_SLOW (this case happens iff the transfer mode has already been set on the device by ide-proc.c::set_xfer_rate()) and remove redundant setting of ->{init,current}_speed. * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* au1xxx: fix au1xxx_set_pio_mode()Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | Set transfer mode on the device before programming the host controller for the new timings (matches what auide_tune_chipset() is doing wrt DMA modes). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* icside: use ide_tune_dma()Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | | * Add "good DMA drives" hack for icside to ide-dma.c::ide_find_dma_mode() (in the long-term it should be either removed or generalized for all hosts). * Use ide_tune_dma() in icside.c::icside_dma_check(). This results in the following changes in behavior: - pre-EIDE SWDMA modes are now also respected - drive->autodma is checked instead of hwif->autodma (doesn't really matter as icside sets both to "1") * Make ide-dma.c::__ide_dma_good_drive() static and drop "__" prefix. Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: fix PIO setup and enable autotuneBenjamin Herrenschmidt2007-10-13
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: use ide_tune_dma() (take 2)Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | | | | | | | | | * Add missing initialization of hwif->autodma and drive->autodma to pmac_ide_setup_dma(). * Use ide_tune_dma() in pmac_ide_dma_check(). While at it: * Fix pmac_ide_dma_check() return value if DMA mode is not programmed (should be "-1" otherwise ide_set_dma() will try to enable DMA). * Remove unnecessary drive->using_dma fiddling (->dma_off_quietly is always called before ide_set_dma() call and ide_set_dma() calls ->ide_dma_on if ->ide_dma_check returns "0"). v2: * No reason to blacklist all ide_floppy devices and the old code was always enabling DMA anyway (without even programming controller/device if the device was ide_floppy). Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: remove pmac_ide_do_setfeature() (take 2)Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove the latter, also ide-iops.c::__ide_wait_stat() could be static again. Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's ->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than the only changes in behavior are: * if PIO mode is set then ->dma_off_queitly is called to disable DMA * if setting transfer mode fails ide_dump_status() is called to dump status v2: * IDE PMAC controllers allow separate PIO and DMA timings and PPC userland depends on this fact, and calls "hdparm -p" without calling "hdparm -d". Therefore to compensate for DMA being disabled by ide_config_drive_speed() for PIO modes: - add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver - add handling of the new flag to ide-io.c::do_special() Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: remove nIEN clearing from pmac_ide_do_setfeature()Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | Upper layers are responsible for controlling nIEN so don't clear nIEN after command execution in pmac_ide_do_setfeature(). Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: use __ide_wait_stat()Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | * Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature(). While at it do following changes to match __ide_wait_stat() call in ide_config_drive_speed(): * Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT. * Check DRQ_STAT bit (shouldn't be set for good device status). Also remove no longer needed wait_for_ready() from ide-iops.c. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: remove extra good status wait from pmac_ide_do_setfeature()Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | Don't check for good device status before executing the command in pmac_ide_do_setfeature() (ide_config_drive_speed() doesn't do this). It is a job of upper layers to guarantee that the device is ready to accept new command before we get here. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add __ide_wait_stat() helperBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | | | | * Split off checking of the status register from ide_wait_stat() to __ide_wait_stat() helper. * Use the new helper in ide_config_drive_speed(). The only change in the functionality is that the function now fails if after 20 sec (WAIT_CMD) device is still busy (BUSY_STAT bit is set) while previously instead of failing the function continued with checking for the correct device status (which would give the device additional 10 usec to clear BUSY_STAT bit). * Remove stale comment for ide_config_drive_speed(). * Remove duplicate comment for ide_wait_stat() from <linux/ide.h>. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: remove pmac_ide_{m,u}dma_enable() (take 2)Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | | * Fix pmac_ide_dma_check() to use pmac_ide_tune_chipset() and remove no longer necessary pmac_ide_{m,u}dma_enable(). * While at it remove some dead code from pmac_ide_dma_check() (leftovers from conversion to use ide_max_dma_mode()). There should be no functionality changes caused by this patch. v2: * Fix compile by replacing "id" with "drive->id" in pmac_ide_dma_check() (Noticed by Ben). Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: remove control register messing from pmac_ide_dma_check()Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | pmac_ide_do_setfeature() contains matching nIEN setting/clearing so this Device Control register messing in pmac_ide_dma_check() is totally unnecessary. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: fix set_timings_mdma()Bartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | | | | | | * Move adjusting of cycle time for devices providing explicit DMA cycle time from pmac_ide_mdma_enable() to set_timings_mdma(). * Remove no longer needed drive_cycle_time argument. * BUG() if unsupported speed argument value is passed (shouldn't happen). * Matching access/recovery timings always exist so remove redundant check. * Make set_timings_mdma() void. * Update pmac_ide_tune_chipset()'s comment. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: pmac_ide_tune_chipset() fixesBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | | * Don't check check for pmif == NULL (it should never be NULL if we got here). * Make a local copy of the timings and set the pmif->timings[] only after setting the transfer mode on the device (otherwise SELECT_DRIVE() call in pmac_ide_do_setfeature() will program new timings before the transfer mode is set on the device - this was pointed out by Sergei). This change makes pmac_ide_tune_chipset() behavior match this of pmac_ide_{m,u}dma_enable(). Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-pmac: don't check kauai_lookup_timing() return valueBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | | | | | | kauai_lookup_timing() should always return non-zero return value: * BUG() in kauai_lookup_timing() if the timing info cannot be found. * Remove code checking for zero return value from all callers. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: unexport ide_acpi_set_stateAdrian Bunk2007-10-13
| | | | | | | | | | This patch removes the unused EXPORT_SYMBOL_GPL(ide_acpi_set_state) Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Shaohua Li <shaohua.li@intel.com> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_platform: set hwif->chipsetBartlomiej Zolnierkiewicz2007-10-13
| | | | | | | We need to set hwif->chipset or IDE PCI host drivers may try to claim our ide_hwifs[] slot. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Driver core: change add_uevent_var to use a structKay Sievers2007-10-12
| | | | | | | | | | | | | | | | | | This changes the uevent buffer functions to use a struct instead of a long list of parameters. It does no longer require the caller to do the proper buffer termination and size accounting, which is currently wrong in some places. It fixes a known bug where parts of the uevent environment are overwritten because of wrong index calculations. Many thanks to Mathieu Desnoyers for finding bugs and improving the error handling. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds2007-10-11
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits) ide: use only ->set_pio_mode method for programming PIO modes (take 2) sis5513: don't change UDMA settings when programming PIO it8213/piix/slc90e66: don't change DMA settings when programming PIO alim15x3: PIO mode setup fixes siimage: fix ->set_pio_mode method to select PIO data transfer cs5520: don't enable VDMA in ->speedproc sc1200: remove redundant warning message from sc1200_tune_chipset() ide-pmac: PIO mode setup fixes (take 3) icside: fix ->speedproc to return on unsupported modes (take 5) sgiioc4: use ide_tune_dma() amd74xx/via82cxxx: use ide_tune_dma() ide: add ide_set{_max}_pio() (take 4) ide: Kconfig face-lift ide: move ide_rate_filter() calls to the upper layer (take 2) sis5513: add ->udma_filter method for chipset_family >= ATA_133 ide: mode limiting fixes for user requested speed changes ide: add missing ide_rate_filter() calls to ->speedproc()-s ide: call udma_filter() before resorting to the UltraDMA mask ide: make jmicron match vendor and device class pdc202xx_new: switch to using pci_get_slot() (take 2) ...
| * ide: use only ->set_pio_mode method for programming PIO modes (take 2)Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate() (the only place which used ->speedproc to program PIO modes) and remove handling of PIO modes from all ->speedproc implementations. v2: * Fix pmac_ide_tune_chipset() comment. There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * sis5513: don't change UDMA settings when programming PIOBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * it8213/piix/slc90e66: don't change DMA settings when programming PIOBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * alim15x3: PIO mode setup fixesBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Return failure in ->speedproc method for unsupported/invalid transfer modes passed from user-space (fixes theoretical OOPS in ali_tune_pio() and/or setting random PIO timings on host controller + disabling UDMA bit + setting unsupported/invalid transfer mode on the device). * Don't disable UDMA bit when programming PIO modes. * Add FIXME about DMA timings never being set. * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * siimage: fix ->set_pio_mode method to select PIO data transferBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | * Remember to select PIO data transfer (with IORDY monitored) in sil_tune_pio() (->set_pio_mode method) so the controller is always programmed correctly for PIO transfers (this is important if DMA is not going to be used). * Don't set DMA/UDMA timings for PIO modes in siimage_tune_chipset(). * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * cs5520: don't enable VDMA in ->speedprocBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | There is no need to do it in cs5520_tune_chipset() (->speedproc method) since it is correctly handled by cs5520_dma_on() (->ide_dma_on method). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * sc1200: remove redundant warning message from sc1200_tune_chipset()Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | ide_config_drive_speed() called by sc1200_set_xfer_mode() already gives a meaningful warning message in case of failure. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide-pmac: PIO mode setup fixes (take 3)Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add { 0, 0 } entry to {kauai,shasta}_pio_timings[] so kauai_lookup_timing() always returns a valid PIO timing (fixes PIO timing not being set for devices with minimum PIO cycle <= 120ns). * Add setting transfer mode on the device to pmac_ide_set_pio_mode(). * Fix pmac_ide_set_pio() to always program chipset for given PIO timing instead of only when the device we want to program PIO timing for is the currently selected one. * Now that pmac_ide_set_pio() is fixed there is no need to set transfer mode on the device and program chipset for PIO in pmac_ide_tune_chipset() (returning 0 == success is not entirely correct but is OK for now since the upper layers are only checking ->speedproc return value for DMA modes). v2: * s/speed/XFER_PIO_0 + pio/ in pmac_ide_set_pio_mode() so it actually compiles. * Removal of kauai_lookup_timing() return value checking went to separate patch. v3: * Use XFER_PIO_0 not XFER_PIO. (Noticed by Ben) Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * icside: fix ->speedproc to return on unsupported modes (take 5)Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * All other implementations of ->speedproc return zero on success and non-zero on failure. Currently it doesn't matter for icside host driver and isn't a bug per se since: - ide_set_xfer_rate() return value is ignored by all IDE core users - icside doesn't (yet!) use ide_tune_dma() in icside_dma_check() but sooner or later we will need to fix anyway - so lets do it now. * icside_set_speed() happily accepts unsupported transfer modes which results in drive->drive_data being set to the maximum value (480) and drive->current_speed being set to the unsupported transfer mode. Fix it. v2: * The initial version of the patch was broken because it didn't take into the account (the different from usual) return values of icside_set_speed() (Noticed by Russell). v3: * Remove no longer needed initialization/checking of cycle_time (Noticed by Sergei). * No need to set drive->drive_data if DMA is not going to be used (Noticed by Sergei). * Remove incorrect setting of drive->current_speed (Noticed by Sergei). * Move ide_config_drive_speed() at the end of icside_set_speed(). v4: * If DMA mode is not found in icside_dma_check() then just return "-1" and don't call icside_set_speed() (v3 got it wrong and "1" was returned instead). v5: * Return "-1"/"0" in icside_set_speed() instead of icside_dma_check() return value (just like it was before this patch). Cc: Russell King <rmk@arm.linux.org.uk> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * sgiioc4: use ide_tune_dma()Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add DRV_NAME define and use it instead of sgiioc4_chipset.name. * Remove no longer needed sgiioc4_chipset. * Remove needless clearing of ->atapi_dma from ide_dma_sgiioc4(). * Fix ide_dma_sgiioc4() to return success/failure. Check return value in sgiioc4_ide_setup_pci_device() and set hwif->autodma accordingly. Also add missing setting of drive->autodma. * Add sgiioc4_speedproc() (implementation of ->speedproc method). * Fix ->mwdma_mask (MWDMA2 mask is 0x04 not 0x02) and remove incorrect ->swdma_mask. Also remove needless initialization of ->ultra_mask. * Use ide_tune_dma() in sgiioc4_ide_dma_check(), this fixes following bugs: - DMA capability bit not being checked on the device - DMA blacklist not being checked - MWDMA2 mode support by device not being checked Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeremy Higdon <jeremy@sgi.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * amd74xx/via82cxxx: use ide_tune_dma()Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | * Use ide_tune_dma() in amd74xx/via82cxxx driver, this fixes following bugs: - DMA capability bit not being checked on the device - DMA blacklist not being checked - DMA mode being programmed even if drive->autodma == 0 (thus possibly destroying PIO timings) * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: add ide_set{_max}_pio() (take 4)Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags and set them in ht6560, cmd640, cmd64x and sc1200 host drivers. * Add set_pio_mode_abuse() for checking if host driver has a non-standard ->tuneproc() implementation and use it in do_special(). * Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find the maximum PIO mode supported by the host), also add ide_set_max_pio() wrapper for ide_set_pio() to use for auto-tuning. Convert users of ->tuneproc to use ide_set{_max}_pio() where possible. This leaves only do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as a direct users of ->tuneproc. * Remove no longer needed ide_get_best_pio_mode() calls and printk-s reporting PIO mode selected from ->tuneproc implementations. * Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const. * Remove stale comment from ide_config_drive_speed(). v2: * Fix "ata_" prefix (Noticed by Jeff). v3: * Minor cleanups/fixups per Sergei's suggestions. v4: * Fix compile problem in drivers/ide/pci/cmd640.c (Noticed by Andrew Morton). * Improve some ->set_pio_mode comments. Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: Kconfig face-liftBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Convert config options for PCI host drivers to select BLK_DEV_IDEPCI. * Same for BLK_DEV_IDEDMA_PCI and PCI DMA host drivers, also make this config option select BLK_DEV_IDEPCI. * Remove no longer needed help for BLK_DEV_IDEPCI and BLK_DEV_IDEDMA_PCI. * Remove redundant IDE_CHIPSETS config option. As a result of this patch users have now three less config options to worry about and can just select host drivers that they need (IDE config menu is "flatter"). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: move ide_rate_filter() calls to the upper layer (take 2)Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Move ide_rate_filter() calls from host drivers to IDE core. * Make ide_rate_filter() static. * Make 'speed' argument of ->speedproc const. v2: * Fix it8213_tune_chipset() comment. There should be no functionality changes caused by this patch. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * sis5513: add ->udma_filter method for chipset_family >= ATA_133Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add sis5513_ata133_udma_filter() for chipset_family >= ATA_133, use it to filter UDMA6 mode if ATA133 bit is disabled. * Remove no longer needed UDMA6 limiting logic from sis5513_tune_chipset(). * Bump driver version. There should be no functionality changes caused by this patch. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: mode limiting fixes for user requested speed changesBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add an extra argument to ide_max_dma_mode() for passing requested transfer mode. Use it as an upper limit when finding the best DMA for device/host. * Rename ide_max_dma_mode() to ide_find_dma_mode() and at the same time add ide_max_dma_mode() wrapper which passes XFER_UDMA_6 as a requested mode to ide_find_dma_mode(). Also add inline ide_find_dma_mode() version for CONFIG_BLK_DEV_IDEDMA=n case. * Pass requested transfer mode from ide_find_dma_mode() to ide_get_mode_mask() to avoid false warning from eighty_ninty_three(). * Use ide_find_dma_mode() to limit the user requested transfer mode in ide_rate_filter(). Also limit the requested mode by host max PIO mode. Above changes make ide_rate_filter() to: * Clip desired transfer mode down if it is invalid (values 0x0F, 0x13-0x19 and 0x25-0x39, values > 0x46 were already clipped down, same for values 0x25-0x39 but iff UDMA was not supported by the host). * Clip desired transfer mode down if it is currently unsupported by IDE core (PIO6 and MWDMA3-4, the latter were already clipped down but iff UDMA was not supported by the host). * Clip desired transfer mode down according to the host capabilities (UDMA modes were already clipped down but MWDMA/SWDMA/PIO weren't, also ->atapi_dma flag was not respected). * Clip desired transfer mode down according to the device capabilities (except PIO modes for now which require mode work) - shouldn't be a problem since ide_set_xfer_rate() is called _after_ device has accepted given transfer mode. and also result in a number of host driver specific bugfixes: * icside - clip unsupported PIO5 mode down - fix unsupported/invalid modes being set in drive->current_speed * ide-cris - clip unsupported PIO5 and SWDMA0-2 modes down - clip DMA modes down for ATAPI devices - fix BUG() on unsupported/invalid modes * au1xxx-ide - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 (if BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA=n) modes down * aec62xx - clip unsupported PIO5 and SWDMA0-2 modes down - clip DMA modes down for ATAPI devices - fix 0x00 being programmed as PIO timing for unsupported/invalid modes - fix unsupported/invalid modes being set on the device * alim15x3 - clip DMA modes down for ATAPI devices (chipset revision == 0x20 only) - fix theoretical OOPS for 0x0F mode - fix unsupported/invalid modes being set on the device * amd74xx - clip unsupported SWDMA0-2 (on COBRA_7401 revs <= 7) modes down - fix random PIO timings being set for unsupported/invalid modes - fix unsupported/invalid modes being set on the device * atiixp - clip unsupported PIO5 and SWDMA0-2 modes down - fix cached MWDMA mode being cleared for unsupported/invalid modes - fix PIO{0,2} timings being programmed for unsupported/invalid modes - fix theoretical OOPS for PIO5-6 and 0x0F modes - fix unsupported/invalid modes being set on the device * cmd64x - clip unsupported SWDMA0-2 modes down * cs5530 - clip unsupported PIO5 and SWDMA0-2 modes down - fix unsupported/invalid modes being set on the device - fix BUG() on unsupported/invalid modes (which happened if the device accepted the setting) * cs5535 - clip unsupported PIO5 and SWDMA0-2 modes down - fix unsupported/invalid modes being set on the device - fix theoretical OOPS for PIO5-6 and 0x0F modes * hpt34x - clip DMA modes down for ATAPI devices - fix invalid timings being programmed for unsupported/invalid modes - fix unsupported/invalid modes being set on the device * hpt366 - clip unsupported PIO5 and SWDMA0-2 modes down - fix PIO0 timings being programmed for unsupported/invalid modes - fix DMA timings being cleared for MWDMA3-4 and 0x25-0x39 modes - fix unsupported/invalid modes being set on the device * it8213 - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down * it821x - clip unsupported PIO5 and SWDMA0-2 modes down - clip DMA modes down for ATAPI devices (chipset in smart mode and revision 0x10 in pass-through mode) * jmicron - clip unsupported SWDMA0-2 modes down - fix unsupported/invalid modes being set on the device * pdc202xx_new - clip unsupported PIO5 and SWDMA0-2 modes down - fix unsupported/invalid modes being set on the device * pdc202xx_old - clip unsupported PIO5 mode down - fix incorrect timings being set for unsupported/invalid modes - fix unsupported/invalid modes being set on the device * piix - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down * sc1200 - clip unsupported PIO5 and SWDMA0-2 modes down - fix unsupported/invalid modes being set on the device - fix BUG() on unsupported/invalid modes (which happened if the device accepted the setting) * scc_pata - clip unsupported PIO5, SWDMA0-2 and MWDMA0-2 modes down * serverworks - clip unsupported PIO5 and SWDMA0-2 modes down - fix DMA/UDMA timings/settings being cleared for unsupported/invalid modes - fix unsupported/invalid modes being set on the device * siimage - clip unsupported PIO5 and SWDMA0-2 modes down - clip DMA modes down for ATAPI devices (SATA chipsets) * sis5513 - clip unsupported PIO5 mode down - fix BUG() on unsupported/invalid modes * sl82c105 - clip unsupported SWDMA0-2 modes down * slc90e66 - clip unsupported PIO5, SWDMA0-1 and MWDMA0 modes down * tc86c001 - clip unsupported PIO5 and SWDMA0-2 modes down - fix PIO0 timings being programmed for PIO5/0x0F/SWDMA0-2/0x13-0x19 modes - fix invalid 0x00 DMA timing being programmed for MWDMA3-4/0x25-0x39 modes - fix unsupported/invalid modes being set on the device * triflex - clip unsupported PIO5 mode down * via82cxxx - fix random PIO timings being set for unsupported/invalid modes - fix unsupported/invalid modes being set on the device * pmac - clip unsupported PIO5 and SWDMA0-2 modes down * cmd640/ht6560b - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y) - fix PIO5 being clipped to PIO4 (if CONFIG_BLK_DEV_IDEDMA=n) * opti621 - clip DMA modes down (if CONFIG_BLK_DEV_IDEDMA=y) - clip unsupported PIO4 to PIO3 (if CONFIG_BLK_DEV_IDEDMA=n) While at it: * Use ide_rate_filter() in cs5520.c::cs5520_tune_chipset(). * Remove no longer needed checks from hpt366.c::hpt3{6,7}x_tune_chipset(). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: add missing ide_rate_filter() calls to ->speedproc()-sBartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Fix icside, cris-ide, au1xxx-ide, amd74xx, via82cxxx and pmac host drivers to use ide_rate_filter(). This results in the following modes (from user requests) being clipped down: - invalid modes (values 0x46-0xFF) [ for all hosts ] - unsupported by a host UDMA modes [ for hosts which support UDMA] - all UDMA modes and MWDMA3-4 modes [ for hosts which don't support UDMA ] - invalid modes (values 0x25-0x39) [ for hosts which don't support UDMA ] * Host driver specific changes in behavior: icside: - no change cris-ide - clip unsupported UDMA3-6 modes down - fix BUG() on trying to set unsupported UDMA3-6 modes au1xxx-ide/pmac - clip unsupported UDMA modes down amd74xx/via82cxxx - clip unsupported UDMA modes down - fix random PIO timings being set for unsupported/invalid modes - fix unsupported/invalid modes being set on the device * While at it remove no longer needed checks from pmac.c driver. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: call udma_filter() before resorting to the UltraDMA maskSergei Shtylyov2007-10-11
| | | | | | | | | | | | | | Give the udma_filter() method call precedence over using the mode masks. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: make jmicron match vendor and device classTejun Heo2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PATA part of all current JMB controllers behave the same way and JMicron confirms that all future ones will stay compatible. Matching vendor and device class is enough. For backward compatibility, jmicron still needs to match 361,3,5,6,8 DIDs regardless of device class if libata is not configured but won't need further DID update from this point. Bart: cosmetic fixes to jmicron_chipset Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Ethan Hsiao <ethanhsiao@jmicron.com> Cc: Justin Tsai <justin@jmicron.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * pdc202xx_new: switch to using pci_get_slot() (take 2)Sergei Shtylyov2007-10-11
| | | | | | | | | | | | | | | | | | | | | | Switch to using pci_get_slot() in init_setup_pdc20270() to get to the mate chip behind DC21150 bridge as there's no need for the driver itself to walk the list of the PCI devices (and the driver didn't check the bus # of the found device). While at it, make it emit warning about IRQ # being fixed up (just like hpt366.c does) and "beautify" this whole function as well as init_setup_pdc20276()... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * ide: hook ACPI _PSx method to IDE power on/offShaohua Li2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ACPI spec defines the sequence of IDE power on/off: Powering down: Call _GTM. Power down drive (calls _PS3 method and turns off power planes). Powering up: Power up drive (calls _PS0 method if present and turns on power planes). Call _STM passing info from _GTM (possibly modified), with ID data from each drive. Initialize the channel. May modify the results of _GTF. For each drive: Call _GTF. Execute task file (possibly modified). This patch adds the missed _PS0/_PS3 methods call. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Len Brown <len.brown@intel.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-26 02:08:32 -0500