aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/ide/pci/cy82c693.c
Commit message (Collapse)AuthorAge
* ide: delete filenames/versions from commentsBartlomiej Zolnierkiewicz2008-02-01
| | | | | | | | | | | | | | | Delete filenames/versions from comments. I'm leaving decisions about adding DRV_VERSION defines and MODULE_VERSION()-s to maintainers of the respective drivers. While at it: * Remove unused VERSION define from ide.c. * Remove unused/stale DRV_VERSION define from au1xxx-ide.c. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: keep pointer to struct device instead of struct pci_dev in ide_hwif_tBartlomiej Zolnierkiewicz2008-02-01
| | | | | | | | | | | Keep pointer to struct device instead of struct pci_dev in ide_hwif_t. While on it: * Use *dev->dma_mask instead of pci_dev->dma_mask in ide_toggle_bounce(). There should be no functionality changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cy82c693: add ->set_dma_mode methodBartlomiej Zolnierkiewicz2008-01-26
| | | | | | | | | | | | | | | | | | | | * Fix SWDMA/MWDMA masks in cy82c693_chipset. * Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to check whether the DMA should be enabled even if ide_max_dma_mode() fails. * Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode() and remove no longer needed cy82c693_ide_dma_on(). Then set IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in cy82c693_chipset. * Bump driver version. As a result of this patch cy82c693 driver will configure and use DMA on all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cy82c693: correct DMA modes clippingBartlomiej Zolnierkiewicz2008-01-26
| | | | | | | | | | | | | | * Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on(). * Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable(): - id->tDMA may not be defined on newer devices - id->vendor6/id->tDMA word is in LE endianness (cy82c693 seems to be Alpha specific though) * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cy82c693: fix build for CONFIG_HOTPLUG=nBartlomiej Zolnierkiewicz2007-10-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On Saturday 20 October 2007, Avuton Olrich wrote: > My randconfig script the attached config caught an error on: > drivers/ide/pci/cy82c693.c:439: error: primary causes a section type conflict > > My git tree: c00046c279a2521075250fad682ca0acc10d4fd7 > > Bisected to: > 8562043606430185cad26d085d46adcc7ad67fd1 is first bad commit > commit 8562043606430185cad26d085d46adcc7ad67fd1 > Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> > Date: Sat Oct 20 00:32:34 2007 +0200 > > ide: constify struct ide_port_info > > Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> It turns out that const and __{dev}initdata cannot be mixed currently. This patch workarounds the problem by removing __devinitdata tag from 'primary' variable (which makes 'primary' to be moved from .init.data to .bss section). Now all __devinitdata data in cy82c693 host driver are read-only so it builds again (driver's .init.data section gets marked as READONLY). While at it: * Move 'primary' variable to its only user, init_iops_cy82c693(). * Bump driver version. Cc: "Avuton Olrich" <avuton@gmail.com> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: constify struct ide_port_infoBartlomiej Zolnierkiewicz2007-10-19
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: replace ide_pci_device_t by struct ide_port_infoBartlomiej Zolnierkiewicz2007-10-19
| | | | | | | | | | | | | | | | * Rename struct ide_pci_device_s to struct ide_port_info. * Remove ide_pci_device_t typedef. While at it: * Fix __ide_pci_register_driver() comment. * Fix aec62xx_init_one() comment. * Remove unused 'cds' field from ide_hwgroup_t. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ->chipset field to ide_pci_device_tBartlomiej Zolnierkiewicz2007-10-19
| | | | | | | | | | | Add ->chipset field to ide_pci_device_t and use it in ide_hwif_configure() to set hwif->chipset. Convert cmd64x, cy82c693, rz1000 and trm290 host drivers to use this new ability. While at it define hwif_chipset_t as u8 to save some space in hw_regs_t, ide_hwif_t and ide_pci_device_t instances. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: set drive->autotune in ide_pci_setup_ports()Bartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | Majority of host drivers using IDE PCI layer set drive->autotune, the only exceptions are: generic.c ns87415.c rz1000.c trm290.c * no ->set_pio_mode method it821x.c: * if memory allocation fails drive->autotune won't be set (but there also won't be ->set_pio_mode method in such case) piix.c: * MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method) However if there is no ->set_pio_mode method there are no changes in behavior w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cy82c693: always tune PIOBartlomiej Zolnierkiewicz2007-10-18
| | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ->mwdma_mask and ->swdma_mask to ide_pci_device_t (take 2)Bartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | * Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t. * Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif method may still override them). * Convert IDE PCI host drivers to use ide_pci_device_t DMA masks. While at it: * Use ATA_{UDMA,MWDMA,SWDMA}* defines. * hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345. * serverworks.c: fix DMA masks being set before checking DMA base. v2: * Add missing masks to DECLARE_GENERIC_PCI_DEV() macro. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_NO_{DMA,AUTODMA} host flagsBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using ide_pci_device_t to use these flags instead of d->autodma and then remove no longer needed d->autodma. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_BOOTABLE host flagBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD} instead of d->bootable and then remove no longer needed d->bootable. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add IDE_HFLAG_NO_ATAPI_DMA host flagBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which don't support ATAPI DMA. Then remove no longer needed hwif->atapi_dma. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove hwif->autodma and drive->autodmaBartlomiej Zolnierkiewicz2007-10-16
| | | | | | | | | | | | | | | | | | | | | | | | | * hpt34x.c: disable DMA masks for HPT345 (hwif->autodma is zero so DMA won't be enabled anyway). * trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag (hwif->autodma is zero so DMA won't be enabled anyway). * Check noautodma global variable instead of drive->autodma in ide_tune_dma(). This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris, au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers. * Remove hwif->autodma (it was not checked by IDE core code anyway) and drive->autodma (was set by all host drivers - except HPT345/TRM290 special cases - unless "ide=nodma" was used). While at it: - remove needless printk() from icside.c - remove stale FIXME/comment from ide-probe.c - don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c (this setting was always later over-ridden by host drivers anyway) Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: use PCI_VDEVICE() macroBartlomiej Zolnierkiewicz2007-10-16
| | | | | | | | | While at it: - make struct pci_device_id tables const - use PCI_DEVICE_ID_ITE_8213 define in it8213.c - fix comment in generic.c Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove ->ide_dma_check (take 2)Bartlomiej Zolnierkiewicz2007-10-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend on BIOS for programming device/controller for DMA. Set it in cy82c693, generic, ns87415, opti621 and trm290 host drivers. * Add IDE_HFLAG_VDMA host flag for host drivers using VDMA. Set it in cs5520 host driver. * Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag. * Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check implementations. Fix all places checking for presence of ->ide_dma_check hook to check for ->ide_dma_on instead. * Remove no longer needed code from config_drive_for_dma(). * Make ide_tune_dma() static. v2: * Fix config_drive_for_dma() return values. * Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding dummy config_drive_for_dma() inline. * Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check(). * Fix init_hwif_it8213() comment. There should be no functionality changes caused by this patch. Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ide_set{_max}_pio() (take 4)Bartlomiej Zolnierkiewicz2007-10-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags and set them in ht6560, cmd640, cmd64x and sc1200 host drivers. * Add set_pio_mode_abuse() for checking if host driver has a non-standard ->tuneproc() implementation and use it in do_special(). * Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find the maximum PIO mode supported by the host), also add ide_set_max_pio() wrapper for ide_set_pio() to use for auto-tuning. Convert users of ->tuneproc to use ide_set{_max}_pio() where possible. This leaves only do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as a direct users of ->tuneproc. * Remove no longer needed ide_get_best_pio_mode() calls and printk-s reporting PIO mode selected from ->tuneproc implementations. * Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const. * Remove stale comment from ide_config_drive_speed(). v2: * Fix "ata_" prefix (Noticed by Jeff). v3: * Minor cleanups/fixups per Sergei's suggestions. v4: * Fix compile problem in drivers/ide/pci/cmd640.c (Noticed by Andrew Morton). * Improve some ->set_pio_mode comments. Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add PIO masksBartlomiej Zolnierkiewicz2007-07-19
| | | | | | | | | | | | | * Add ATA_PIO[0-6] defines to <linux/ata.h>. * Add ->pio_mask field to ide_pci_device_t and ide_hwif_t. * Add PIO masks to host drivers. <linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: drop "PIO data" argument from ide_get_best_pio_mode()Bartlomiej Zolnierkiewicz2007-07-19
| | | | | | | | | | * Drop no longer needed "PIO data" argument from ide_get_best_pio_mode() and convert all users accordingly. * Remove no longer needed ide_pio_data_t. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ide_pci_device_t.host_flags (take 2)Bartlomiej Zolnierkiewicz2007-07-19
| | | | | | | | | | | | | | | | | | * Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS. * Add IDE_HFLAG_SINGLE flag for single channel devices. * Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE and remove no longer needed ide_pci_device_t.channels field. v2: * Fix issues noticed by Sergei: - correct code alignment in scc_pata.c - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: use PIO/MMIO operations directly where possible (v2)Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | This results in smaller/faster/simpler code and allows future optimizations. Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}. v2: * updated for scc_pata Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove ide_pci_device_t tables with only one entryBartlomiej Zolnierkiewicz2007-02-16
| | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add missing __init tags to IDE PCI host driversBartlomiej Zolnierkiewicz2007-01-27
| | | | | | also change __devinit tag for sgiioc4.c:ioc4_ide_init() to __init Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* [PATCH] IDE: more pci_find cleanupAlan Cox2006-10-03
| | | | | | Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Remove obsolete #include <linux/config.h>Jörn Engel2006-06-30
| | | | | Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
* [PATCH] ide: possible cleanupsAdrian Bunk2005-11-09
| | | | | | | | | | | | This patch contains the following possible cleanups: - pci/cy82c693.c: make a needlessly global function static - remove the following unneeded EXPORT_SYMBOL's: - ide-taskfile.c: do_rw_taskfile - ide-iops.c: default_hwif_iops - ide-iops.c: default_hwif_transport - ide-iops.c: wait_for_ready Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* [PATCH] ide: hotplug mark __devinit cy82c693.cHerbert Xu2005-07-03
| | | | | | | | | From: Herbert Xu <herbert@gondor.apana.org.au> mark the __init section __devinit. Splitted up from the Debian kernel patch. Signed-off-by: maximilian attems <janitor@sternwelten.at> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
* Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds2005-04-16
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-12 05:04:22 -0500