| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For optimus and powerxpress muxless we really want the GPU
driver deciding when to power up/down the GPU, not userspace.
This adds the ability for a driver to dynamically power up/down
the GPU and remove the switcheroo from controlling it, the
switcheroo reports the dynamic state to userspace also.
It also adds 2 power domains, one for machine where the power
switch is controlled outside the GPU D3 state, so the powerdown
ordering is done correctly, and the second for the hdmi audio
device to make sure it can resume for PCI config space accesses.
v1.1: fix build with switcheroo off
v2: add power domain support for radeon and v1 nvidia dsms
v2.1: fix typo in off case
v3: add audio power domain for hdmi audio + misc audio fixes
v4: use PCI_SLOT macro, drop power reference on hdmi audio resume
failure also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Okay so Alan's patch handled the case where there was no registered fbcon,
however the other path entered in set_con2fb_map pit.
In there we called fbcon_takeover, but we also took the console lock in a couple
of places. So push the console lock out to the callers of set_con2fb_map,
this means fbmem and switcheroo needed to take the lock around the fb notifier
entry points that lead to this.
This should fix the efifb regression seen by Maarten.
Tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Tested-by: Lu Hua <huax.lu@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
| |
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
This callback is a no-op in nouveau, and the upcoming apple-gmux
switcheroo support won't require it either. Rather than forcing drivers
to stub it out, just make it optional and remove the callback from
nouveau.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
vga_switcheroo assumes that the handler will be registered before the
last client, otherwise switching will not be enabled. Likewise it's
assumed that the handler will not be unregistered without at least one
client also being unregistered, otherwise switching will remain enabled
despite no longer having a handler. These assumptions cannot be enforced
if the handler is in a separate driver from both clients, as with the
gmux found in Apple laptops. Remove this assumption.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
The audio clients have to be disabled before disabling the VGA and
switching. Similarly, enabling the audio client should be done at
last. Otherwise the audio-side operation stalls, eventually leading
to Oops or lockups.
Tested-by: Jörg-Volker Peetz <jvpeetz@web.de>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
| |
Add vga_switcheroo_get_client_state() to get the current state of the
client. This is necessary to determine the proper initial state of
audio clients in HD-audio driver.
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
| |
Add the support for audio clients to VGA-switcheroo for handling the
HDMI audio controller together with VGA switching. The id of the
audio controller should be given explicitly at registration time
unlike the video controller.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43155
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
|
| |
This changes the API as a clean-up. Instead of passing multiple
function pointers at each time, introduce a new struct holding the
whole callback functions and pass it to the registration.
The same struct will be used for the upcoming audio client
registration, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
| |
Refactor the code base a bit for the further work to adapt more clients.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |
|
|
|
|
|
|
|
|
| |
vga-switcheroo currently changes the default VGA device by fiddling with
the IORESOURCE_ROM_SHADOW flag on the device. This isn't strictly accurate,
since there's no guarantee that switching also changes the ROM decoding.
Switch over to using the vgaarb functions for this.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This is unbalanced and probably more fitting for the client
to take care of. Remove it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If the requested device is already active, ignore the request.
This restores the original behaviour of the interface. The change was
probably an unintended side effect of
commit 66b37c6777c4 vga_switcheroo: split switching into two stages
which did not take into account to duplicate the !active check in the split-off
stage2.
Fix this by factoring that check out of stage1 into the debugfs_write routine.
References: https://bugzilla.kernel.org/show_bug.cgi?id=34252
Reported-by: Igor Murzov <e-mail@date.by>
Tested-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
| |
This is a copy-and-paste bug. We should be comparing 4 characters here
instead of 3.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
stage 1: turn card on, switch boot vga pointer.
stage 2: switch fbs, switch mux and power off old card.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
This adds a hook after the mux is switched for the driver to reprobe
the connected outputs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
This allows the mux to be switched from userspace using MIGD/MDIS
command to the switch.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
At least on the nvidia mux the power switch seems to be executed
by the ACPI PS0/PS3 methods so need to do it explicitly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
| |
We really want to see this so we can confirm that we pick the right one.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
| |
Stanse found that one error path in vga_switcheroo_debugfs_write omits to
unlock vgasr_mutex. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
radeon was always including the atpx code unnecessarily, also core
switcheroo was including acpi headers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
|
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
