aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/ata
Commit message (Collapse)AuthorAge
* libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQTejun Heo2008-12-01
| | | | | | | | | | | | | | | Some recent Seagate harddrives have firmware bug which causes FLUSH CACHE to timeout under certain circumstances if NCQ is being used. This can be worked around by disabling NCQ and fixed by updating the firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these devices. The wiki page has been updated to contain information on this issue. http://ata.wiki.kernel.org/index.php/Known_issues Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] pata_rb532_cf: fix signature of the xfer functionPhil Sutter2008-12-01
| | | | | | | | | | | | Per definition, this function should return the number of bytes consumed. As the original parameter "buflen" is being decremented inside the read/write loop, save it in "retlen" at the beginning. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com> Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] pata_rb532_cf: fix and rename register definitionsPhil Sutter2008-12-01
| | | | | | | | | | | | | | The original standalone driver uses a custom address for the error register. Use it in pata_rb532_cf, too. Rename two register definitions: - The address offset 0x0800 in fact is the ATA base, not ATA command address. - The offset 0x0C00 is not a regular ATA data address, but a buffered one allowing 4-byte IO. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ata_piix: add borked Tecra M4 to broken suspend listTejun Heo2008-12-01
| | | | | | | | | | | | | | | | Tecra M4 sometimes forget what it is and reports bogus data via DMI which makes the machine evade broken suspend matching and thus fail suspend/resume. This patch updates piix_broken_suspend() such that it can match such case. As the borked DMI data is a bit generic, matching many entries to make the match more specific is necessary. As the usual DMI matching is limited to four entries, this patch uses hard coded manual matching. This is reported by Alexandru Romanescu. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: improve phantom device detectionTejun Heo2008-11-14
| | | | | | | | | | | | | | | | | | | | | | | Currently libata uses four methods to detect device presence. 1. PHY status if available. 2. TF register R/W test (only promotes presence, never demotes) 3. device signature after reset 4. IDENTIFY failure detection in SFF state machine Combination of the above works well in most cases but recently there have been a few reports where a phantom device causes unnecessary delay during probe. In both cases, PHY status wasn't available. In one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which didn't qualify as #4. The other failed #2 but as it passed #3 and #4, it still caused failure. In both cases, phantom device reported diagnostic failure, so these cases can be safely worked around by considering any !ATA_DRQ IDENTIFY failure as NODEV_HINT if diagnostic failure is set. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: fix last_reset timestamp handlingTejun Heo2008-11-11
| | | | | | | | | | | | | | | | | | | ehc->last_reset is used to ensure that resets are not issued too close to each other. It's initialized to jiffies minus one minute on EH entry. However, when new links are initialized after PMP is probed, new links have zero for this timestamp resulting in long wait depending on the current jiffies. This patch makes last_set considered iff ATA_EHI_DID_RESET is set, in which case last_reset is always initialized. As an added precaution, WARN_ON() is added so that warning is printed if last_reset is in future. This problem is spotted and debugged by Shane Huang. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Shane Huang <Shane.Huang@amd.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: Avoid overflow in ata_tf_read_block() when tf->hba_lbal > 127Roland Dreier2008-11-11
| | | | | | | | | | Phillip O'Donnell <phillip.odonnell@gmail.com> pointed out that the same sign extension bug that was fixed in commit ba14a9c2 ("libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127") also appears to exist in ata_tf_read_block(). Fix this by adding a cast to u64. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] pata_pcmcia: another memory card supportMarc Pignat2008-11-11
| | | | | | | Support for Apacer photo steno pro card. Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] pata_sch: notice attached slave devicesMark Salter2008-11-11
| | | | | | | | | I posted this last month, but was prompted to do so again in bz#467457 Add capability flag to support slave devices with pata_sch driver. Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] pata_cs553*.c: cleanup kernel-docQinghuang Feng2008-11-11
| | | | | | | | No arguments named @deadline in cs5535_cable_detect() and cs5536_cable_detect(). Remove them. Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: revert convert-to-block-tagging patchesTejun Heo2008-11-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch reverts the following three commits which convert libata to use block layer tagging. 43a49cbdf31e812c0d8f553d433b09b421f5d52c e013e13bf605b9e6b702adffbe2853cfc60e7806 2fca5ccf97d2c28bcfce44f5b07d85e74e3cd18e Although using block layer tagging is the right direction, due to the tight coupling among tag number, data structure allocation and hardware command slot allocation, libata doesn't work correctly with the current conversion. The biggest problem is guaranteeing that tag 0 is always used for non-NCQ commands. Due to the way blk-tag is implemented and how SCSI starts and finishes requests, such guarantee can't be made. I'm not sure whether this would actually break any low level driver but it doesn't look like a good idea to break such assumption given the frailty of ATA controllers. So, for the time being, keep using the old dumb in-libata qc allocation. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Jens Axobe <jens.axboe@oracle.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* libata: mask off DET when restoring SControl for detachTejun Heo2008-11-04
| | | | | | | | | | libata restores SControl on detach; however, trying to restore non-zero DET can cause undeterministic behavior including PMP device going offline till power cycling. Mask off DET when restoring SControl. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: implement ATA_HORKAGE_ATAPI_MOD16_DMA and apply itTejun Heo2008-11-04
| | | | | | | | | | | | | | | libata always uses PIO for ATAPI commands when the number of bytes to transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes PIO transfers. Implement a horkage to skip the mod16 check and apply it to the quantum device. This is reported by John Clark in the following thread. http://thread.gmane.org/gmane.linux.ide/34748 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: John Clark <clarkjc@runbox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: Fix a potential race condition in ata_scsi_park_show()Elias Oltmanns2008-11-04
| | | | | | | | | | | | Peter Moulder has pointed out that there is a slight chance that a negative value might be passed to jiffies_to_msecs() in ata_scsi_park_show(). This is fixed by saving the value of jiffies in a local variable, thus also reducing code since the volatile variable jiffies is accessed only once. Signed-off-by: Elias Oltmanns <eo@nebensachen.de> Signed-off-by: Tejun Heo <tj.kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sata_nv: fix generic, nf2/3 detection regressionTejun Heo2008-11-04
| | | | | | | | | | | | | | | | | | | | | | | All three flavors of sata_nv's are different in how their hardreset behaves. * generic: Hardreset is not reliable. Link often doesn't come online after hardreset. * nf2/3: A little bit better - link comes online with longer debounce timing. However, nf2/3 can't reliable wait for the first D2H Register FIS, so it can't wait for device readiness or classify the device after hardreset. Follow-up SRST required. * ck804: Hardreset finally works. The core layer change to prefer hardreset and follow up changes exposed the above issues and caused various detection regressions for all three flavors. This patch, hopefully, fixes all the known issues and should make sata_nv error handling more reliable. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sata_via: restore vt*_prepare_host error handlingMarcin Slusarz2008-11-04
| | | | | | | | | | | | | | | commit b9d5b89b487517cbd4cb4702da829e07ef9e4432 (sata_via: fix support for 5287) accidently (?) removed vt*_prepare_host error handling - restore it catched by gcc: drivers/ata/sata_via.c: In function 'svia_init_one': drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: Joseph Chan <JosephChan@via.com.tw> Cc: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sata_promise: add ATA engine reset to reset opsMikael Pettersson2008-11-04
| | | | | | | | | | | | | | | | | | | | Promise ATA engines need to be reset when errors occur. That's currently done for errors detected by sata_promise itself, but it's not done for errors like timeouts detected outside of the low-level driver. The effect of this omission is that a timeout tends to result in a sequence of failed COMRESETs after which libata EH gives up and disables the port. At that point the port's ATA engine hangs and even reloading the driver will not resume it. To fix this, make sata_promise override ->hardreset on SATA ports with code which calls pdc_reset_port() on the port in question before calling libata's hardreset. PATA ports don't use ->hardreset, so for those we override ->softreset instead. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: add whitelist for devices with known good pata-sata bridgesJens Axboe2008-10-31
| | | | | | | | | | | | | libata currently imposes a UDMA5 max transfer rate and 200 sector max transfer size for SATA devices that sit behind a pata-sata bridge. Lots of devices have known good bridges that don't need this limit applied. The MTRON SSD disks are such devices. Transfer rates are increased by 20-30% with the restriction removed. So add a "blacklist" entry for the MTRON devices, with a flag indicating that the bridge is known good. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* sata_via: fix support for 5287Tejun Heo2008-10-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | 5287 used to be treated as vt6420 but it didn't work. It's new family of controllers called vt8251 which hosts four SATA ports as M/S of the two ATA ports. This configuration is rather peculiar in that although the M/S devices are on the same port, each have its own SCR (or equivalent link status/control) registers which screws up the port-link-device hierarchy assumed by libata. Another controller which falls into this category is ata_piix w/ SIDPR access. libata now has facility to deal with this class of controllers named slave_link. A low level driver for such controllers can just call ata_slave_link_init() on the respective ports and libata will handle all the difficult parts like following up with single SRST after hardresetting both ports. This patch creates new controller class vt8251, implements slave_link aware init sequence and config space based SCR access for it and moves 5287 to the new class. This patch is based on Joseph Chan's larger patch which was created before slave_link was implemented in libata. http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Joseph Chan <JosephChan@via.com.tw> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: Avoid overflow in ata_tf_to_lba48() when tf->hba_lbal > 127Roland Dreier2008-10-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | In ata_tf_to_lba48(), when evaluating (tf->hob_lbal & 0xff) << 24 the expression is promoted to signed int (since int can hold all values of u8). However, if hob_lbal is 128 or more, then it is treated as a negative signed value and sign-extended when promoted to u64 to | into sectors, which leads to the MSB 32 bits of section getting set incorrectly. For example, Phillip O'Donnell <phillip.odonnell@gmail.com> reported that a 1.5GB drive caused: ata3.00: HPA detected: current 2930277168, native 18446744072344861488 where 2930277168 == 0xAEA87B30 and 18446744072344861488 == 0xffffffffaea87b30 which shows the problem when hob_lbal is 0xae. Fix this by adding a cast to u64, just as is used by for hob_lbah and hob_lbam in the function. Reported-by: Phillip O'Donnell <phillip.odonnell@gmail.com> Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ATA: remove excess kernel-doc notationRandy Dunlap2008-10-31
| | | | | | | | | | | Remove excess kernel-doc function parameter notation from drivers/ata/: Warning(drivers/ata/libata-core.c:1622): Excess function parameter or struct member 'fn' description in 'ata_pio_queue_task' Warning(drivers/ata/libata-core.c:4655): Excess function parameter or struct member 'err_mask' description in 'ata_qc_complete' Warning(drivers/ata/ata_piix.c:751): Excess function parameter or struct member 'udma' description in 'do_pata_set_dmamode' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Merge branch 'upstream-linus' of ↵Linus Torvalds2008-10-28
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata: ahci enclosure management bit mask libata: ahci enclosure management led sync pata_ninja32: suspend/resume support libata: Fix LBA48 on pata_it821x RAID volumes. libata: clear saved xfer_mode and ncq_enabled on device detach sata_sil24: configure max read request size to 4k libata: add missing kernel-doc libata: fix device iteration bugs ahci: Add support for Promise PDC42819 ata: Switch all my stuff to a common address
| * libata: ahci enclosure management bit maskDavid Milburn2008-10-28
| | | | | | | | | | | | | | Enclosure management bit mask definitions. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * libata: ahci enclosure management led syncDavid Milburn2008-10-28
| | | | | | | | | | | | | | Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock. Signed-off-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * pata_ninja32: suspend/resume supportAlan Cox2008-10-28
| | | | | | | | | | | | | | | | | | I had assumed that the standard recovery would be sufficient for this hardware but it isn't. Fix up the other registers on resume as needed. See bug #11735 Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * libata: Fix LBA48 on pata_it821x RAID volumes.Ondrej Zary2008-10-27
| | | | | | | | | | | | | | | | [http://lkml.org/lkml/2008/10/18/82] Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * libata: clear saved xfer_mode and ncq_enabled on device detachTejun Heo2008-10-27
| | | | | | | | | | | | | | | | | | | | libata EH saves xfer_mode and ncq_enabled at start to later set DUBIOUS_XFER flag if it has changed. These values need to be cleared on device detach such that hot device swap doesn't accidentally miss DUBIOUS_XFER. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * sata_sil24: configure max read request size to 4kTejun Heo2008-10-27
| | | | | | | | | | | | | | | | | | | | | | | | Due to request posting limitations, bandwidth of sil3132 is limited to around 120MB/s with the minimum pci-e payload size (128bytes) which is used by most consumer systems. However, write throughput can be slightly (~3%) increased by increasing the max read requeset size. Configure it to 4k which is the maximum supported. This optimization is also done by SIMG's windows driver. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * libata: add missing kernel-docRandy Dunlap2008-10-27
| | | | | | | | | | | | | | | | | | | | Fix libata missing kernel-doc: Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description found for parameter 'tag' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * libata: fix device iteration bugsTejun Heo2008-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | There were several places where only enabled devices should be iterated over but device enabledness wasn't checked. * IDENTIFY data 40 wire check in cable_is_40wire() * xfer_mode/ncq_enabled saving in ata_scsi_error() * DUBIOUS_XFER handling in ata_set_mode() While at it, reformat comments in cable_is_40wire(). Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * ahci: Add support for Promise PDC42819Mark Nelson2008-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add an appropriate entry for the Promise PDC42819 controller. It has an AHCI mode and so far works correctly with board_ahci. This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port) software-based RAID cards (for which there is a binary driver, t3sas) and can be found on some motherboards, for example the MSI K9A2 Platinum, which calls the chip a Promise T3 controller. Although this controller also supports SAS devices, its default bootup mode is AHCI and the binary driver has to do some magic to get the chip into the appropriate mode to drive SAS disks. Seeing as no documentation is provided by Promise, adding this entry to the ahci driver allows the controller to be useful to people as a SATA controller (with no ill effects on the system if a SAS disk is connected - probing of the port just times out with "link online but device misclassified"), without having to resort to using the binary driver. Users who require SAS or the proprietary software raid can get this functionality using the binary driver. Signed-off-by: Mark Nelson <mdnelson8@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
| * ata: Switch all my stuff to a common addressAlan Cox2008-10-27
| | | | | | | | Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | libata: fix NCQ devices behind port multipliersJens Axboe2008-10-27
|/ | | | | | | For devices behind sata port multipliers, we have to make sure that they share a tag map since all tags for that PMP must be unique. Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* libata: fix bug with non-ncq devicesJens Axboe2008-10-24
| | | | | | | | | | | | | | | | | | The recent commit 2fca5ccf97d2c28bcfce44f5b07d85e74e3cd18e ("libata: switch to using block layer tagging support") to enable support for block layer tagging in libata was broken for non-NCQ devices The block layer initializes the tag field to -1 to detect invalid uses of a tag, and if the libata devices does NOT support NCQ, we just used that field to index the internal command list. So we need to check for -1 first and only use the tag field if it's valid. Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Reported-by: Alexander Beregalov <a.beregalov@gmail.com> Tested-by: Paul Mundt <lethal@linux-sh.org> Tested-by: Dave Young <hidave.darkstar@gmail.com> Tested-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* libata: switch to using block layer tagging supportJens Axboe2008-10-23
| | | | | | | | | | | libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding a free tag to use. Instead of fixing that up, convert libata to using block layer tagging - gets rid of code in libata, and is also much faster. Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'release' of ↵Linus Torvalds2008-10-23
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (123 commits) dock: make dock driver not a module ACPI: fix ia64 build warning ACPI: hack around sysfs warning with link order ACPI suspend: fix build warning when CONFIG_ACPI_SLEEP=n intel_menlo: fix build warning panasonic-laptop: fix build ACPICA: Update version to 20080926 ACPICA: Add support for zero-length buffer-to-string conversions ACPICA: New: Validation for predefined ACPI methods/objects ACPICA: Fix for implicit return compatibility ACPICA: Fixed a couple memory leaks associated with "implicit return" ACPICA: Optimize buffer allocation procedure ACPICA: Fix possible memory leak, error exit path ACPICA: Fix fault after mem allocation failure in AML parser ACPICA: Remove unused ACPI register bit definition ACPICA: Update version to 20080829 ACPICA: Fix possible memory leak in acpi_ns_get_external_pathname ACPICA: Cleanup for internal Reference Object ACPICA: Update comments - no functional changes ACPICA: Update for Reference ACPI_OPERAND_OBJECT ...
| * Merge branch 'linus' into testLen Brown2008-10-23
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: MAINTAINERS arch/x86/kernel/acpi/boot.c arch/x86/kernel/acpi/sleep.c drivers/acpi/Kconfig drivers/pnp/Makefile drivers/pnp/quirks.c Signed-off-by: Len Brown <len.brown@intel.com>
| * \ Merge branch 'dock' into testLen Brown2008-10-22
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/acpi/osl.c Signed-off-by: Len Brown <len.brown@intel.com>
| | * | dock: introduce .uevent for devices in dock, eg libataShaohua Li2008-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | dock's uevent reported itself, not ata. It might be difficult to find an ata device just according to a dock. This patch introduces docking ops for each device in a dock. when docking, dock driver can send device specific uevent. This should help dock station too (not just bay) Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
| | * | libata: remove functions now handed by ACPI dock driverShaohua Li2008-09-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | dock driver can handle ata(bay) hotplug now. dock driver already handles _EJ0 and _STA, so remove them. Also libata doesn't need register notification handler anymore. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Len Brown <len.brown@intel.com>
* | | | sata_via: load DEVICE register when CTL changesTejun Heo2008-10-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | VIA controllers clear DEVICE register when IEN changes. Make sure DEVICE is updated along with CTL. This change is separated from Joseph Chan's larger patch. http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640 Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Joseph Chan <JosephChan@via.com.tw> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | | | libata: set device class to NONE if phys_offlineTejun Heo2008-10-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reset methods don't have access to phys link status for slave links and may incorrectly indicate device presence causing unnecessary probe failures for unoccupied links. This patch clears device class to NONE during post-reset processing if phys link is offline. As on/offlineness semantics is strictly defined and used in multiple places by the core layer, this won't change behavior for drivers which don't use slave links. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | | | libata-eh: fix slave link EH action mask handlingTejun Heo2008-10-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Slave link action mask is transferred to master link and all the EH actions are taken by the master link. ata_eh_about_to_do() and ata_eh_done() are called with ATA_EH_ALL_ACTIONS to clear the slave link actions during transfer. This always sets ATA_PFLAG_RECOVERED flag causing spurious "EH complete" messages. Don't set ATA_PFLAG_RECOVERED for slave link actions. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | | | libata: transfer EHI control flags to slave ehc.iTejun Heo2008-10-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior of EH. As only the master link is visible outside EH, these flags are set only for the master link although they should also apply to the slave link, which causes spurious EH messages during probe and suspend/resume. This patch transfers those two flags to slave ehc.i before performing slave autopsy and reporting. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | | | libata-sff: fix ata_sff_post_internal_cmd()Tejun Heo2008-10-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ata_sff_post_internal_cmd() needs to grab port lock before calling ata_bmdma_stop() and also need to clear hsm_task_state. Fix it. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | | | libata: initialize port_task when !CONFIG_ATA_SFFTejun Heo2008-10-22
| |_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | ap->port_task was not initialized if !CONFIG_ATA_SFF later triggering lockdep warning. Make sure it's initialized. Reported by Larry Finger. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | | Merge commit 'origin'Benjamin Herrenschmidt2008-10-14
|\ \ \ | | | | | | | | | | | | | | | | | | | | Manual fixup of conflicts on: arch/powerpc/include/asm/dcr-regs.h drivers/net/ibm_newemac/core.h
| * \ \ Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6Linus Torvalds2008-10-13
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (49 commits) pcmcia: ioctl-internal definitions pcmcia: cistpl header cleanup pcmcia: remove unused argument to pcmcia_parse_tuple() pcmcia: card services header cleanup pcmcia: device_id header cleanup pcmcia: encapsulate ioaddr_t pcmcia: cleanup device driver header file pcmcia: cleanup socket services header file pcmcia: merge ds_internal.h into cs_internal.h pcmcia: cleanup cs_internal.h pcmcia: cs_internal.h is internal pcmcia: use dev_printk for cs_error() pcmcia: remove CS_ error codes alltogether pcmcia: deprecate CS_BAD_TUPLE pcmcia: deprecate CS_BAD_ARGS pcmcia: deprecate CS_BAD_BASE, CS_BAD_IRQ, CS_BAD_OFFSET and CS_BAD_SIZE pcmcia: deprecate CS_BAD_ATTRIBUTE, CS_BAD_TYPE and CS_BAD_PAGE pcmcia: deprecate CS_NO_MORE_ITEMS pcmcia: deprecate CS_IN_USE pcmcia: deprecate CS_CONFIGURATION_LOCKED ... Fix trivial conflict in drivers/pcmcia/ds.c manually
| | | \ \
| | | \ \
| | *-. \ \ Merge branches 'pcmcia-config-loop' and 'pcmcia-printk' into pcmciaDominik Brodowski2008-08-22
| | |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * pcmcia-config-loop: pcmcia: pcmcia_config_loop() improvement by passing vcc pcmcia: pcmcia_config_loop() default CIS entry handling pcmcia: pcmcia_config_loop() ConfigIndex unification pcmcia: use pcmcia_loop_config in misc pcmcia drivers pcmcia: use pcmcia_loop_config in net pcmcia drivers pcmcia: use pcmcia_loop_config in ISDN pcmcia drivers pcmcia: use pcmcia_loop_config in scsi pcmcia drivers pcmcia: use pcmcia_loop_config in bluetooth drivers pcmcia: use pcmcia_loop_config in pata and ide drivers pcmcia: add pcmcia_loop_config() helper * pcmcia-printk: pcmcia: don't add extra DEBUG cflag pcmcia: remove unused cs_socket_name() definition pcmcia: use dev_printk in module rsrc_nonstatic pcmcia: use dev_printk in module pcmcia pcmcia: use dev_printk in module pcmcia_core pcmcia: use dev_printk and dev_dbg in yenta_socket
| | | * | | | pcmcia: pcmcia_config_loop() improvement by passing vccDominik Brodowski2008-08-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | By passing the current Vcc setting to the pcmcia_config_loop callback function, we can remove pcmcia_get_configuration_info() calls from many drivers. Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-18 13:19:35 -0500