aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_sis.c
Commit message (Collapse)AuthorAge
* ata: use module_pci_driverAxel Lin2012-07-25
| | | | | | | | | | | | | | This patch converts the drivers in drivers/ata/* to use module_pci_driver() macro which makes the code smaller and a bit simpler. Signed-off-by: Axel Lin <axel.lin@gmail.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Mikael Pettersson <mikpe@it.uu.se> Cc: Mark Lord <kernel@teksavvy.com> Cc: Jeremy Higdon <jeremy@sgi.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_sis: code style cleanups for consistencyDan McGee2011-10-08
| | | | | | | | Remove a lot of ' ' (double spaces) as well as ensuring use of tabs vs. spaces is appropriate and consistent. Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_sis: mark most const data static as wellDan McGee2011-10-08
| | | | | | | | | | This pushes timing and other values into preinitialized read-only data sections rather than being inlined into the code. None of these functions are called more than a handful of times, so reducing code size makes sense. Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_sis: enable MWDMA for UDMA 133 chipsetDan McGee2011-10-08
| | | | | | | | | | | This ports the timing values over from the old IDE driver into the new PATA-based one. The comment was lying when it stated the old driver was not MWDMA capable. Boot tested on actual hardware using 'libata.force=mwdma2'. Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_sis: add mode_filter method for certain sis5513 chipsetsDan McGee2011-10-08
| | | | | | | | | | | | | | | | | This mirrors a very old commit (3160d5416f39da9d9, "sis5513: add ->udma_filter method for chipset_family >= ATA_133") to the old sis5513 IDE driver that prevents certain setups from working. UDMA6 (ATA/133) is not supported on some chipsets and we need to ensure this mode is not chosen even if a connected drive supports it. Port this old patch forward to the new PATA driver to ensure UDMA5 is the highest mode used if that is what is supported. Kernel bugzilla #41582. Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_sis: extract a sis_port_base() methodDan McGee2011-10-08
| | | | | | | | | | This is similar to the existing sis_old_port_base() method. We do this same calculation and logic in multiple places (with one more to come in a future patch), so extracting it into a method makes sense. Reviewed-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Dan McGee <dpmcgee@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ata: Add and use ata_print_version_onceJoe Perches2011-07-23
| | | | | | | | | | | | | | | | | | | Use a single mechanism to show driver version. Reduces text a tiny bit too. Remove uses of static int printed_version Add and use ata_print_version(const struct device *, const char *ver) and ata_print_version_once. $ size drivers/ata/built-in.* text data bss dec hex filename 544969 73893 116584 735446 b38d6 drivers/ata/built-in.allyesconfig.ata.o 543870 73893 116592 734355 b34ad drivers/ata/built-in.allyesconfig.print_once.o 141328 14689 4220 160237 271ed drivers/ata/built-in.defconfig.ata.o 141212 14689 4220 160121 27179 drivers/ata/built-in.defconfig.print_once.o Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* Fix common misspellingsLucas De Marchi2011-03-31
| | | | | | Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
* libata: remove ATA_FLAG_{SRST|SATA_RESET}Sergei Shtylyov2011-03-02
| | | | | | | | | These flags are marked as obsolete and the checks for them have been removed by commit 294440887b32c58d220fb54b73b7a58079b78f20 (libata-sff: kill unused ata_bus_reset()), so I think it's time to finally get rid of them... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata-sff: separate out BMDMA initTejun Heo2010-05-25
| | | | | | | | | Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one() from their SFF counterparts. SFF ones no longer try to initialize BMDMA or set PCI master. Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: Pass host flags into the pci helperAlan Cox2010-03-01
| | | | | | | | | | This allows parallel scan and the like to be set without having to stop using the existing full helper functions. This patch merely adds the argument and fixes up the callers. It doesn't undo the special cases already in the tree or add any new parallel callers. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"Jeff Garzik2009-12-07
| | | | | | | | | | | | | | | | | | | | This reverts commit f20941f334d8fdb6b598658979709b4e94cd034b. Sergei Shtylyov notes "You call min() on uncomparables [in mwdma_clip_to_pio()], i.e. mwdma_to_pio[] contains XFER_PIO_* and adev->pio_mode - XFER_PIO_0 yields you a mode number. Thus the second argument will always "win" as a minimal one" Bartlomiej Zolnierkiewicz adds "There are more issues with the patch related to mwdma_clip_to_pio(). The function can return values between 0 and 4 which obviously won't work well for the new code below for values >2 (i.e. resulting in out-of-bounds array access for the common-case of dev->pio_mode == XFER_PIO_4)." Bartlomiej Zolnierkiewicz also notes the patch is incomplete, failing to update MWDMA mode masks. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_sis: Power Management fixBartlomiej Zolnierkiewicz2009-12-03
| | | | | | | Call sis_fixup() on resume. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* pata_sis: Implement MWDMA for the UDMA 133 capable chipsAlan Cox2009-12-03
| | | | | | | | Bartlomiej pointed out that while this got fixed in the old driver whoever did it didn't port it across. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] convert drivers to use ata.h mode mask definesErik Inge Bolsø2009-03-24
| | | | | | | No functional changes in this patch. Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* [libata] Update kernel-doc comments to match source codeQinghuang Feng2008-12-28
| | | | Signed-off-by: Qinghuang Feng <qhfeng.kernel@gmail.com>
* pata_sis: Remove bogus cable matchAlan Cox2008-12-09
| | | | | | | | | | | | | | Some systems report SIS 5513 as both vendor/id and subvendor/id string. In that case we can't distinguish the system by the id svid/sdid and in fact the entry here breaks some boxes. At some point we need to find another way to detect the Targa Visionary 1000, until then this trades a hang for some users with lower performance for others. Closes: #12092 Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* ata: Switch all my stuff to a common addressAlan Cox2008-10-27
| | | | Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Added Targa Visionary 1000 IDE adapter to pata_sis.cKai Krakow2008-07-11
| | | | | | | This enables short 40-wire detection for my laptop thus enabling UDMA/100. Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* libata: rename SFF functionsTejun Heo2008-04-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SFF functions have confusing names. Some have sff prefix, some have bmdma, some std, some pci and some none. Unify the naming by... * SFF functions which are common to both BMDMA and non-BMDMA are prefixed with ata_sff_. * SFF functions which are specific to BMDMA are prefixed with ata_bmdma_. * SFF functions which are specific to PCI but apply to both BMDMA and non-BMDMA are prefixed with ata_pci_sff_. * SFF functions which are specific to PCI and BMDMA are prefixed with ata_pci_bmdma_. * Drop generic prefixes from LLD specific routines. For example, bfin_std_dev_select -> bfin_dev_select. The following renames are noteworthy. ata_qc_issue_prot() -> ata_sff_qc_issue() ata_pci_default_filter() -> ata_bmdma_mode_filter() ata_dev_try_classify() -> ata_sff_dev_classify() This rename is in preparation of separating SFF support out of libata core layer. This patch strictly renames functions and doesn't introduce any behavior difference. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: make reset related methods proper port operationsTejun Heo2008-04-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: stop overloading port_info->private_dataTejun Heo2008-04-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | port_info->private_data is currently used for two purposes - to record private data about the port_info or to specify host->private_data to use when allocating ata_host. This overloading is confusing and counter-intuitive in that port_info->private_data becomes host->private_data instead of port->private_data. In addition, port_info and host don't correspond to each other 1-to-1. Currently, the first non-NULL port_info->private_data is used. This patch makes port_info->private_data just be what it is - private_data for the port_info where LLD can jot down extra info. libata no longer sets host->private_data to the first non-NULL port_info->private_data, @host_priv argument is added to ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use this argument to pass in pointer to host private data. LLDs which don't should use init-register model anyway and can initialize host->private_data directly. Adding @host_priv instead of using init-register model for LLDs which use ata_pci_init_one() is suggested by Alan Cox. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
* libata: make ata_pci_init_one() not use ops->irq_handler and pi->shtTejun Heo2008-04-17
| | | | | | | | | | | | | | | | | | | ata_pci_init_one() is the only function which uses ops->irq_handler and pi->sht. Other initialization functions take the same information as arguments. This causes confusion and duplicate unused entries in structures. Make ata_pci_init_one() take sht as an argument and use ata_interrupt implicitly. All current users use ata_interrupt and if different irq handler is necessary open coding ata_pci_init_one() using ata_prepare_sff_host() and ata_activate_sff_host can be done under ten lines including error handling and driver which requires custom interrupt handler is likely to require custom initialization anyway. As ata_pci_init_one() was the last user of ops->irq_handler, this patch also kills the field. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: implement and use ops inheritanceTejun Heo2008-04-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: implement and use SHT initializersTejun Heo2008-04-17
| | | | | | | | | | | | | | | | libata lets low level drivers build scsi_host_template and register it to the SCSI layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This patch implements SHT initializers which can be used to initialize all the boilerplate entries in a sht. Three variants of them are implemented - BASE, BMDMA and NCQ - for different types of drivers. Note that entries can be overriden by putting individual initializers after the helper macro. All sht tables are identical before and after this patch. Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: PCI device should be powered up before being accessedTejun Heo2008-04-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | PCI device should be powered up or powered up before its PCI regsiters are accessed. Although PCI configuration register access is allowed in D3hot, PCI device is free to reset its status when transiting from D3hot to D0 causing configuration data to change. Many libata SFF drivers which use ata_pci_init_one() read and update configuration registers before calling ata_pci_init_one() which enables the PCI device. Also, in resume paths, some drivers access registers without resuming the PCI device. This patch adds a call to pcim_enable_device() in init path if register is accessed before calling ata_pci_init_one() and make resume paths first resume PCI devices, access PCI configuration regiters then resume ATA host. While at it... * cmd640 was strange in that it set ->resume even when CONFIG_PM is not. This is by-product of minimal build fix. Updated. * In cs5530, Don't BUG() on reinit failure. Just whine and fail resume. Signed-off-by: Tejun Heo <htejun@gmail.com>
* drivers/ata/: Spelling fixesJoe Perches2008-02-03
| | | | | Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Adrian Bunk <bunk@kernel.org>
* pata_sis.c: Add Packard Bell EasyNote K5305 to laptopsGabriel C2007-11-18
| | | | | | | | With newer kernels HDD in my old laptop is limited to UDMA 33. With this patch I get UDMA 100 again. Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com> Signed-off-by: Tejun Heo <htejun@gmail.com>
* libata: Switch most of the remaining SFF drivers to ata_sff_port_startAlan Cox2007-10-12
| | | | | | | | This avoids allocating DMA buffers if not needed but at the moment is mostly just a neatness item. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Remove ->port_disable() hookJeff Garzik2007-10-12
| | | | | | | | It was always set to ata_port_disable(). Removed the hook, and replaced the very few ap->ops->port_disable() callsites with direct calls to ata_port_disable(). Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()Jeff Garzik2007-10-12
| | | | | | | | | | | | | * ->irq_ack() is redundant to what the irq handler already performs... chk-status + irq-clear. Furthermore, it is only called in one place, when screaming-irq-debugging is enabled, so we don't want to bother with a hook just for that. * ata_dummy_irq_on() is only ever used in drivers that have no callpath reaching ->irq_on(). Remove .irq_on hook from those drivers, and the now-unused ata_dummy_irq_on() Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-link: linkify resetTejun Heo2007-10-12
| | | | | | | | | | | | | | Make reset methods and related functions deal with ata_link instead of ata_port. * ata_do_reset() * ata_eh_reset() * all prereset/reset/postreset methods and related functions This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-link: introduce ata_linkTejun Heo2007-10-12
| | | | | | | | | | | | | | | | | | | Introduce ata_link. It abstracts PHY and sits between ata_port and ata_device. This new level of abstraction is necessary to support SATA Port Multiplier, which basically adds a bunch of links (PHYs) to a ATA host port. Fields related to command execution, spd_limit and EH are per-link and thus moved to ata_link. This patch only defines the host link. Multiple link handling will be added later. Also, a lot of ap->link derefences are added but many of them will be removed as each part is converted to deal directly with ata_link instead of ata_port. This patch introduces no behavior change. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_sis: add missing UDMA5 timing value in sis_66_set_dmamode()Tejun Heo2007-09-25
| | | | | | | | | | | | | sis_66_set_dmamode() also handles early UDMA100 (SIS630 ET) but is missing udma timing value for UDMA100. According to sis5513, this should be 0x8000. This caused UDMA100 device to fail on pata_sis till it downgrades to UDMA66 while it works fine on sis5513 at UDMA100. Reported by Adam Blech. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Adam Blech <desaster.area@addcom.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_sis: Add the FSC Amilo and friendsAlan Cox2007-08-23
| | | | | | | More short cables Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_sis: fix MWDMA for <= UDMA66 chipsets and UDMA for UDMA33 chipsetsBartlomiej Zolnierkiewicz2007-08-01
| | | | | | | | | | | | | | | | | | | | | | | | | * Fix MWDMA timings setup in sis_old_set_dmamode() and sis_66_set_dmamode(). The old timings were overclocked (even worse behavior than sis5513 IDE driver which depends on BIOS to program correct timings), the new timings are taken from the datasheet (they match timings from ATA spec). * Fix UDMA timings setup in sis_old_set_dmamode(). Misplaced pci_write_config_word() call resulted in UDMA timings never being set. * Fix comments for sis_133_early_set_dmamode() and sis_133_set_dmamode(): - only the former function handles early SiS 961 bridges - both functions lack MWDMA timings setup * Fix typos in sis_100_set_piomode() and sis_133_set_piomode() comments. * Bump driver version. Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6Linus Torvalds2007-07-12
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits) PCI: Only build PCI syscalls on architectures that want them PCI: limit pci_get_bus_and_slot to domain 0 PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3 PCI: hotplug: pciehp: wait for 1 second after power off slot PCI: pci_set_power_state(): check for PM capabilities earlier PCI: cpci_hotplug: Convert to use the kthread API PCI: add pci_try_set_mwi PCI: pcie: remove SPIN_LOCK_UNLOCKED PCI: ROUND_UP macro cleanup in drivers/pci PCI: remove pci_dac_dma_... APIs PCI: pci-x-pci-express-read-control-interfaces cleanups PCI: Fix typo in include/linux/pci.h PCI: pci_ids, remove double or more empty lines PCI: pci_ids, add atheros and 3com_2 vendors PCI: pci_ids, reorder some entries PCI: i386: traps, change VENDOR to DEVICE PCI: ATM: lanai, change VENDOR to DEVICE PCI: Change all drivers to use pci_device->revision ...
| * PCI: Change all drivers to use pci_device->revisionAuke Kok2007-07-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Instead of all drivers reading pci config space to get the revision ID, they can now use the pci_device->revision member. This exposes some issues where drivers where reading a word or a dword for the revision number, and adding useless error-handling around the read. Some drivers even just read it for no purpose of all. In devices where the revision ID is being copied over and used in what appears to be the equivalent of hotpath, I have left the copy code and the cached copy as not to influence the driver's performance. Compile tested with make all{yes,mod}config on x86_64 and i386. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Acked-by: Dave Jones <davej@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | pata_sis: FIFO whackAlan Cox2007-07-10
|/ | | | | | | | | If you are using a SiS controller and the BIOS didn't set it up then the FIFO may be left active when we try and set up the CD. Not convinced this matters but I'd prefer to be safe Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] PATA drivers: remove ATA_FLAG_SRSTJeff Garzik2007-07-09
| | | | | | | This flag only has meaning in old-EH drivers, and these drivers have already been converted to the new EH. Remove. Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: PATA-mode fixes for sis_sataUwe Koziolek2007-07-02
| | | | | | | | | | | | | | | | Changed PATA handler for PATA-ports used by sata_sis. This patch was originally submitted by Jeff Garzik. Added PCI-ID 1180 for SiS966 Controller in pata_sis. The 1180 mode is fully compatible to other SiS PATA-controller. The PCI-ID 1183 is SATA in PATA-emulation, but not fully compatible to SiS5513/5518. sata_sis.c is forwarding this ID to pata_sis. 1183 is not working if simply added to pata_sis. This handling fixes issues with SiS968. Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_sis: Fix and clean up some timing setupsAlan Cox2007-05-24
| | | | | | | | | | - Rename sis_port_base to sis_old_port_base() so nobody uses it for new generation controllers in error. - Use byte size operations where it is cleaner for mode setup - Fix a couple of masking errors on certai chip revs when setting speeds Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: clean up SFF init messTejun Heo2007-05-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: reimplement suspend/resume support using sdev->manage_start_stopTejun Heo2007-05-11
| | | | | | | | | | | | | | | | | | | | | | | Reimplement suspend/resume support using sdev->manage_start_stop. * Device suspend/resume is now SCSI layer's responsibility and the code is simplified a lot. * DPM is dropped. This also simplifies code a lot. Suspend/resume status is port-wide now. * ata_scsi_device_suspend/resume() and ata_dev_ready() removed. * Resume now has to wait for disk to spin up before proceeding. I couldn't find easy way out as libata is in EH waiting for the disk to be ready and sd is waiting for EH to complete to issue START_STOP. * sdev->manage_start_stop is set to 1 in ata_scsi_slave_config(). This fixes spindown on shutdown and suspend-to-disk. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata reset-seq] build and merge fixesJeff Garzik2007-05-01
| | | | Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: add deadline support to prereset and reset methodsTejun Heo2007-05-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add @deadline to prereset and reset methods and make them honor it. ata_wait_ready() which directly takes @deadline is implemented to be used as the wait function. This patch is in preparation for EH timing improvements. * ata_wait_ready() never does busy sleep. It's only used from EH and no wait in EH is that urgent. This function also prints 'be patient' message automatically after 5 secs of waiting if more than 3 secs is remaining till deadline. * ata_bus_post_reset() now fails with error code if any of its wait fails. This is important because earlier reset tries will have shorter timeout than the spec requires. If a device fails to respond before the short timeout, reset should be retried with longer timeout rather than silently ignoring the device. There are three behavior differences. 1. Timeout is applied to both devices at once, not separately. This is more consistent with what the spec says. 2. When a device passes devchk but fails to become ready before deadline. Previouly, post_reset would just succeed and let device classification remove the device. New code fails the reset thus causing reset retry. After a few times, EH will give up disabling the port. 3. When slave device passes devchk but fails to become accessible (TF-wise) after reset. Original code disables dev1 after 30s timeout and continues as if the device doesn't exist, while the patched code fails reset. When this happens, new code fails reset on whole port rather than proceeding with only the primary device. If the failing device is suffering transient problems, new code retries reset which is a better behavior. If the failing device is actually broken, the net effect is identical to it, but not to the other device sharing the channel. In the previous code, reset would have succeeded after 30s thus detecting the working one. In the new code, reset fails and whole port gets disabled. IMO, it's a pathological case anyway (broken device sharing bus with working one) and doesn't really matter. * ata_bus_softreset() is changed to return error code from ata_bus_post_reset(). It used to return 0 unconditionally. * Spin up waiting is to be removed and not converted to honor deadline. * To be on the safe side, deadline is set to 40s for the time being. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_sis: Clean up using cable_detect methodsAlan Cox2007-04-28
| | | | | | | | | | | | | | | This changeset revolves around the fact that all the SiS controllers have the same enable bits, but differing cable detection methods. Previously that meant each type had its own error_handler methods. Instead we can now implement different ->cable_detect methods and share a single error_handler which does the filtering by enable bits. In addition we had some auto const arrays that should be static const. I'm not sure if gcc already treats them intelligently but adding the static will make sure. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_sis: Fix oops on bootAlan Cox2007-04-19
| | | | | | | | | | | A small number of SiS setups require special handling (not many judging by how long this dumb bug survived). A couple of Fedora 7 devel testers hit an Oops on pata_sis loading which is caused by terminal confusion between chipset as 'the chipset we have found' and chipset as 'array iterator' Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: add missing CONFIG_PM in LLDsTejun Heo2007-03-02
| | | | | | | | Add missing #ifdef CONFIG_PM conditionals around all PM related parts in libata LLDs. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* [libata] bump versionsJeff Garzik2007-02-26
| | | | | | Bump versions based on changes submitted during 2.6.21 merge window. Signed-off-by: Jeff Garzik <jeff@garzik.org>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-27 20:41:33 -0500