| Commit message (Collapse) | Author | Age |
|---|
| |\
| |
| |
| |
| |
| |
| |
| | |
Backmerge from the point in mainline where a trivial conflict had been
introduced (arch/sparc/kernel/sys_sparc_64.c had grown sys_kern_features()
right after where kernel_execve() used to be)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The Montgomery Multiply, Montgomery Square, and Multiple-Precision
Multiply instructions work by loading a combination of the floating
point and multiple register windows worth of integer registers
with the inputs.
These values are 64-bit. But for 32-bit userland processes we only
save the low 32-bits of each integer register during a register spill.
This is because the register window save area is in the user stack and
has a fixed layout.
Therefore, the only way to use these instruction in 32-bit mode is to
perform the following sequence:
1) Load the top-32bits of a choosen integer register with a sentinel,
say "-1". This will be in the outer-most register window.
The idea is that we're trying to see if the outer-most register
window gets spilled, and thus the 64-bit values were truncated.
2) Load all the inputs for the montmul/montsqr/mpmul instruction,
down to the inner-most register window.
3) Execute the opcode.
4) Traverse back up to the outer-most register window.
5) Check the sentinel, if it's still "-1" store the results.
Otherwise retry the entire sequence.
This retry is extremely troublesome. If you're just unlucky and an
interrupt or other trap happens, it'll push that outer-most window to
the stack and clear the sentinel when we restore it.
We could retry forever and never make forward progress if interrupts
arrive at a fast enough rate (consider perf events as one example).
So we have do limited retries and fallback to software which is
extremely non-deterministic.
Luckily it's very straightforward to provide a mechanism to let
32-bit applications use a 64-bit stack. Stacks in 64-bit mode are
biased by 2047 bytes, which means that the lowest bit is set in the
actual %sp register value.
So if we see bit zero set in a 32-bit application's stack we treat
it like a 64-bit stack.
Runtime detection of such a facility is tricky, and cumbersome at
best. For example, just trying to use a biased stack and seeing if it
works is hard to recover from (the signal handler will need to use an
alt stack, plus something along the lines of longjmp). Therefore, we
add a system call to report a bitmask of arch specific features like
this in a cheap and less hairy way.
With help from Andy Polyakov.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fix from Greg Kroah-Hartman:
"Here is one patch, a revert of a omap serial driver patch that was
causing problems, for your 3.7-rc tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: omap: fix software flow control"
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This reverts commit 957ee7270d632245b43f6feb0e70d9a5e9ea6cf6
(serial: omap: fix software flow control).
As Russell has pointed out, that commit isn't fixing
Software Flow Control at all, and it actually makes
it even more broken.
It was agreed to revert this commit and use Russell's
latest UART patches instead.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping revert from Marek Szyprowski:
"Due to my mistake, my previous pull request (merged as commit
cff7b8ba60e3: "Merge branch 'fixes_for_linus' ..") contained a patch
which is aimed for v3.8 and lacks its dependences. This pull request
reverts it and fixes build break of ARM architecture."
* 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
Revert "ARM: dma-mapping: support debug_dma_mapping_error"
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This reverts commit 871ae57adc5ed092c1341f411514d0e8482e2611, which is
scheduled for v3.8 and accidently got into v3.7-rc series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
| | |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This fixes a couple of nasty page table initialization bugs which were
causing kdump regressions. A clean rearchitecturing of the code is in
the works - meanwhile these are reverts that restore the
best-known-working state of the kernel.
There's also EFI fixes and other small fixes."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mm: Undo incorrect revert in arch/x86/mm/init.c
x86: efi: Turn off efi_enabled after setup on mixed fw/kernel
x86, mm: Find_early_table_space based on ranges that are actually being mapped
x86, mm: Use memblock memory loop instead of e820_RAM
x86, mm: Trim memory in memblock to be page aligned
x86/irq/ioapic: Check for valid irq_cfg pointer in smp_irq_move_cleanup_interrupt
x86/efi: Fix oops caused by incorrect set_memory_uc() usage
x86-64: Fix page table accounting
Revert "x86/mm: Fix the size calculation of mapping tables"
MAINTAINERS: Add EFI git repository location
|
| | | |\ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fixes from Matt Fleming:
"Fix oops with EFI variables on mixed 32/64-bit firmware/kernels and
document EFI git repository location on kernel.org."
Conflicts:
arch/x86/include/asm/efi.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When 32-bit EFI is used with 64-bit kernel (or vice versa), turn off
efi_enabled once setup is done. Beyond setup, it is normally used to
determine if runtime services are available and we will have none.
This will resolve issues stemming from efivars modprobe panicking on a
32/64-bit setup, as well as some reboot issues on similar setups.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45991
Reported-by: Marko Kohtala <marko.kohtala@gmail.com>
Reported-by: Maxim Kammerer <mk@dee.su>
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@kernel.org # 3.4 - 3.6
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Commit
844ab6f9 x86, mm: Find_early_table_space based on ranges that are actually being mapped
added back some lines back wrongly that has been removed in commit
7b16bbf97 Revert "x86/mm: Fix the size calculation of mapping tables"
remove them again.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQW_vuaYQbmagVnxT2DGsYc=9tNeAbdBq53sYkitPOwxSQ@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Current logic finds enough space for direct mapping page tables from 0
to end. Instead, we only need to find enough space to cover mr[0].start
to mr[nr_range].end -- the range that is actually being mapped by
init_memory_mapping()
This is needed after 1bbbbe779aabe1f0768c2bf8f8c0a5583679b54a, to address
the panic reported here:
https://lkml.org/lkml/2012/10/20/160
https://lkml.org/lkml/2012/10/21/157
Signed-off-by: Jacob Shin <jacob.shin@amd.com>
Link: http://lkml.kernel.org/r/20121024195311.GB11779@jshin-Toonie
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We need to handle E820_RAM and E820_RESERVED_KERNEL at the same time.
Also memblock has page aligned range for ram, so we could avoid mapping
partial pages.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVZirvaBMFYRfXMmWEcHbKSicQEHz4VAwUv0xFCk51ZNw@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We will not map partial pages, so need to make sure memblock
allocation will not allocate those bytes out.
Also we will use for_each_mem_pfn_range() to loop to map memory
range to keep them consistent.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVZirvaBMFYRfXMmWEcHbKSicQEHz4VAwUv0xFCk51ZNw@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
smp_irq_move_cleanup_interrupt
Posting this patch to fix an issue concerning sparse irq's that
I raised a while back. There was discussion about adding
refcounting to sparse irqs (to fix other potential race
conditions), but that does not appear to have been addressed
yet. This covers the only issue of this type that I've
encountered in this area.
A NULL pointer dereference can occur in
smp_irq_move_cleanup_interrupt() if we haven't yet setup the
irq_cfg pointer in the irq_desc.irq_data.chip_data.
In create_irq_nr() there is a window where we have set
vector_irq in __assign_irq_vector(), but not yet called
irq_set_chip_data() to set the irq_cfg pointer.
Should an IRQ_MOVE_CLEANUP_VECTOR hit the cpu in question during
this time, smp_irq_move_cleanup_interrupt() will attempt to
process the aforementioned irq, but panic when accessing
irq_cfg.
Only continue processing the irq if irq_cfg is non-NULL.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/20121016125021.GA22935@sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Calling __pa() with an ioremap'd address is invalid. If we
encounter an efi_memory_desc_t without EFI_MEMORY_WB set in
->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.
On CONFIG_X86_32 this results in the following oops:
BUG: unable to handle kernel paging request at f7f22280
IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
*pdpt = 0000000001978001 *pde = 0000000001ffb067 *pte = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
Modules linked in:
Pid: 0, comm: swapper Not tainted 3.0.0-acpi-efi-0805 #3
EIP: 0060:[<c10257b9>] EFLAGS: 00010202 CPU: 0
EIP is at reserve_ram_pages_type+0x89/0x210
EAX: 0070e280 EBX: 38714000 ECX: f7814000 EDX: 00000000
ESI: 00000000 EDI: 38715000 EBP: c189fef0 ESP: c189fea8
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=c189e000 task=c18bbe60 task.ti=c189e000)
Stack:
80000200 ff108000 00000000 c189ff00 00038714 00000000 00000000 c189fed0
c104f8ca 00038714 00000000 00038715 00000000 00000000 00038715 00000000
00000010 38715000 c189ff48 c1025aff 38715000 00000000 00000010 00000000
Call Trace:
[<c104f8ca>] ? page_is_ram+0x1a/0x40
[<c1025aff>] reserve_memtype+0xdf/0x2f0
[<c1024dc9>] set_memory_uc+0x49/0xa0
[<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
[<c19216d4>] start_kernel+0x291/0x2f2
[<c19211c7>] ? loglevel+0x1b/0x1b
[<c19210bf>] i386_start_kernel+0xbf/0xc8
The only time we can call set_memory_uc() for a memory region is
when it is part of the direct kernel mapping. For the case where
we ioremap a memory region we must leave it alone.
This patch reimplements the fix from e8c7106280a3 ("x86, efi:
Calling __pa() with an ioremap()ed address is invalid") which
was reverted in e1ad783b12ec because it caused a regression on
some MacBooks (they hung at boot). The regression was caused
because the commit only marked EFI_RUNTIME_SERVICES_DATA as
E820_RESERVED_EFI, when it should have marked all regions that
have the EFI_MEMORY_RUNTIME attribute.
Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because of the way that the memory map might be
configured as detailed in the following bug report,
https://bugzilla.redhat.com/show_bug.cgi?id=748516
e.g. some of the EFI memory regions *need* to be mapped as part
of the direct kernel mapping.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Keith Packard <keithp@keithp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1350649546-23541-1-git-send-email-matt@console-pimps.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Commit 20167d3421a089a1bf1bd680b150dc69c9506810 ("x86-64: Fix
accounting in kernel_physical_mapping_init()") went a little too
far by entirely removing the counting of pre-populated page
tables: this should be done at boot time (to cover the page
tables set up in early boot code), but shouldn't be done during
memory hot add.
Hence, re-add the removed increments of "pages", but make them
and the one in phys_pte_init() conditional upon !after_bootmem.
Reported-Acked-and-Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/506DAFBA020000780009FA8C@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Commit:
722bc6b16771 x86/mm: Fix the size calculation of mapping tables
Tried to address the issue that the first 2/4M should use 4k pages
if PSE enabled, but extra counts should only be valid for x86_32.
This commit caused a kdump regression: the kdump kernel hangs.
Work is in progress to fundamentally fix the various page table
initialization issues that we have, via the design suggested
by H. Peter Anvin, but it's not ready yet to be merged.
So, to get a working kdump revert to the last known working version,
which is the revert of this commit and of a followup fix (which was
incomplete):
bd2753b2dda7 x86/mm: Only add extra pages count for the first memory range during pre-allocation
Tested kdump on physical and virtual machines.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Tested-by: Flavio Leitner <fbl@redhat.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Flavio Leitner <fbl@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: ianfang.cn@gmail.com
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | |\ \ \ \ \
| | |_|_|/ /
| |/| | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Most of the kernel diffstat relates to a group of Intel P6 and KNC
(Xeon-Phi Knights Corner) PMU driver fixes, neither of which is in
heavy use, so we took the fixes.
The rest is diverse smallish fixes to the tooling and kernel side."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Remove unused variable in nhmex_rbox_alter_er()
perf/x86: Enable overflow on Intel KNC with a custom knc_pmu_handle_irq()
perf/x86: Remove cpuc->enable check on Intl KNC event enable/disable
perf/x86: Make Intel KNC use full 40-bit width of counters
perf/x86/uncore: Handle pci_read_config_dword() errors
perf/x86: Remove P6 cpuc->enabled check
perf/x86: Update/fix generic events on P6 PMU
perf/x86: Fix P6 FP_ASSIST event constraint
perf, cpu hotplug: Use cached value of smp_processor_id()
perf, cpu hotplug: Run CPU_STARTING notifiers with irqs disabled
x86/perf: Fix virtualization sanity check
perf test: Fix exclude_guest parse events tests
perf tools: do not flush maps on COMM for perf report
perf help: Fix --help for builtins
perf trace: Check if sample raw_data field is set
perf trace: Validate syscall id before growing syscall table
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The variable port is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Yan, Zheng <zheng.z.yan@intel.com>
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: acme@ghostprotocols.net
Link: http://lkml.kernel.org/r/CAPgLHd8NZkYSkZm22FpZxiEh6HcA0q-V%3D29vdnheiDhgrJZ%2Byw@mail.gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Although based on the Intel P6 design, the interrupt mechnanism
for KNC more closely resembles the Intel architectural
perfmon one.
We can't just re-use that code though, because KNC has different
MSR numbers for the status and ack registers.
In this case we just cut-and paste from perf_event_intel.c
with some minor changes, as it looks like it would not be
worth the trouble to change that code to be MSR-configurable.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: eranian@gmail.com
Cc: Meadows Lawrence F <lawrence.f.meadows@intel.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210171304410.23243@vincent-weaver-1.um.maine.edu
[ Small stylistic edits. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
x86_pmu.enable() is called from x86_pmu_enable() with
cpuc->enabled set to 0. This means we weren't re-enabling the
counters after a context switch.
This patch just removes the check, as it should't be necessary
(and the equivelent x86_ generic code does not have the checks).
The origin of this problem is the KNC driver being based on the
P6 one. The P6 driver also has this issue, but works anyway
due to various lucky accidents.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: eranian@gmail.com
Cc: Meadows
Cc: Lawrence F <lawrence.f.meadows@intel.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210171303290.23243@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Early versions of Intel KNC chips have a bug where bits above 32
were not properly set. We worked around this by only using the
bottom 32 bits (out of 40 that should be available).
It turns out this workaround breaks overflow handling.
The buggy silicon will in theory never be used in production
systems, so remove this workaround so we get proper overflow
support.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: eranian@gmail.com
Cc: Meadows Lawrence F <lawrence.f.meadows@intel.com>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210171302140.23243@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This, beyond handling corner cases, also fixes some build warnings:
arch/x86/kernel/cpu/perf_event_intel_uncore.c: In function ‘snbep_uncore_pci_disable_box’:
arch/x86/kernel/cpu/perf_event_intel_uncore.c:124:9: warning: ‘config’ is used uninitialized in this function [-Wuninitialized]
arch/x86/kernel/cpu/perf_event_intel_uncore.c: In function ‘snbep_uncore_pci_enable_box’:
arch/x86/kernel/cpu/perf_event_intel_uncore.c:135:9: warning: ‘config’ is used uninitialized in this function [-Wuninitialized]
arch/x86/kernel/cpu/perf_event_intel_uncore.c: In function ‘snbep_uncore_pci_read_counter’:
arch/x86/kernel/cpu/perf_event_intel_uncore.c:164:2: warning: ‘count’ is used uninitialized in this function [-Wuninitialized]
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Cc: a.p.zijlstra@chello.nl
Link: http://lkml.kernel.org/r/1351068140-13456-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Between 2.6.33 and 2.6.34 the PMU code was made modular.
The x86_pmu_enable() call was extended to disable cpuc->enabled
and iterate the counters, enabling one at a time, before calling
enable_all() at the end, followed by re-enabling cpuc->enabled.
Since cpuc->enabled was set to 0, that change effectively caused
the "val |= ARCH_PERFMON_EVENTSEL_ENABLE;" code in p6_pmu_enable_event()
and p6_pmu_disable_event() to be dead code that was never called.
This change removes this code (which was confusing) and adds some
extra commentary to make it more clear what is going on.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210191732000.14552@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This patch updates the generic events on p6, including some new
extended cache events.
Values for these events were taken from the equivelant PAPI
predefined events.
Tested on a Pentium II.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210191730080.14552@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
According to Intel SDM Volume 3B, FP_ASSIST is limited to Counter 1 only,
not Counter 0.
Tested on a Pentium II.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1210191728570.14552@vincent-weaver-1.um.maine.edu
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | | |/ / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
In check_hw_exists() we try to detect non-emulated MSR accesses
by writing an arbitrary value into one of the PMU registers
and check if it's value after a readout is still the same.
This algorithm silently assumes that the register does not contain
the magic value already, which is wrong in at least one situation.
Fix the algorithm to really do a read-modify-write cycle. This fixes
a warning under Xen under some circumstances on AMD family 10h CPUs.
The reasons in more details actually sound like a story from
Believe It or Not!:
First you need an AMD family 10h/12h CPU. These do not reset the
PERF_CTR registers on a reboot.
Now you boot bare metal Linux, which goes successfully through this
check, but leaves the magic value of 0xabcd in the register. You
don't use the performance counters, but do a reboot (warm reset).
Then you choose to boot Xen. The check will be triggered with a
recent Linux kernel as Dom0 again, trying to write 0xabcd into the
MSR. Xen silently drops the write (expected), but the subsequent read
will return the value in the register, which just happens to be the
expected magic value. Thus the test misleadingly succeeds, leaving
the kernel in the belief that the PMU is available. This will trigger
the following message:
[ 0.020294] ------------[ cut here ]------------
[ 0.020311] WARNING: at arch/x86/xen/enlighten.c:730 xen_apic_write+0x15/0x17()
[ 0.020318] Hardware name: empty
[ 0.020323] Modules linked in:
[ 0.020334] Pid: 1, comm: swapper/0 Not tainted 3.3.8 #7
[ 0.020340] Call Trace:
[ 0.020354] [<ffffffff81050379>] warn_slowpath_common+0x80/0x98
[ 0.020369] [<ffffffff810503a6>] warn_slowpath_null+0x15/0x17
[ 0.020378] [<ffffffff810034df>] xen_apic_write+0x15/0x17
[ 0.020392] [<ffffffff8101cb2b>] perf_events_lapic_init+0x2e/0x30
[ 0.020410] [<ffffffff81ee4dd0>] init_hw_perf_events+0x250/0x407
[ 0.020419] [<ffffffff81ee4b80>] ? check_bugs+0x2d/0x2d
[ 0.020430] [<ffffffff81002181>] do_one_initcall+0x7a/0x131
[ 0.020444] [<ffffffff81edbbf9>] kernel_init+0x91/0x15d
[ 0.020456] [<ffffffff817caaa4>] kernel_thread_helper+0x4/0x10
[ 0.020471] [<ffffffff817c347c>] ? retint_restore_args+0x5/0x6
[ 0.020481] [<ffffffff817caaa0>] ? gs_change+0x13/0x13
[ 0.020500] ---[ end trace a7919e7f17c0a725 ]---
The new code will change every of the 16 low bits read from the
register and tries to write and read-back that modified number
from the MSR.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Link: http://lkml.kernel.org/r/1349797115-28346-2-git-send-email-andre.przywara@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
|
| | | |\ \ \ \
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into fixes
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
On NOMMU ARM, the __addr_ok() and __range_ok() macros do not evaluate
their arguments, which may lead to harmless build warnings in some
code where the variables are not used otherwise. Adding a cast to void
gets rid of the warning and does not make any semantic changes.
Without this patch, building at91x40_defconfig results in:
fs/read_write.c: In function 'rw_copy_check_uvector':
fs/read_write.c:684:9: warning: unused variable 'buf' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The flat_get_addr_from_rp() macro does not use the 'persistent' argument
on ARM, causing a harmless compiler warning. A cast to void removes
that warning.
Without this patch, building at91x40_defconfig results in:
fs/binfmt_flat.c: In function 'load_flat_file':
fs/binfmt_flat.c:746:17: warning: unused variable 'persistent' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@canonical.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Sometimes we want the kernel build process to only print messages
on errors, e.g. in automated build testing. This uses the "kecho"
macro that the build system provides to hide a few informational
messages. Nothing changes for a regular "make" or "make V=1".
Without this patch, building any ARM kernel results in:
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Michal Marek <mmarek@suse.cz>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The Linaro cross toolchain and probably others nowadays default to
building in THUMB2 mode. When building a kernel for a CPU that does
not support THUMB2, the compiler complains about incorrect flags.
We can work around this by setting -marm for all non-T2 builds.
-marm was passed unconditionally for C files previously, but nothing was
passed to the gcc frontend when processing .S files, resulting in a
warning. The assembler never defaults to ARM unless -Wa,-mthumb is
supplied explicitly, so the files were still assembled correctly.
This patch makes sure that -marm is passed for .S files too, and also
avoids the redundant gcc -marm -mthumb in Thumb kernels.
Without this patch, building assabet_defconfig results in:
usr/initramfs_data.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
arch/arm/nwfpe/entry.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
firmware/cis/PCMLM28.cis.gen.S:1:0: warning: target CPU does not support THUMB instructions [enabled by default]
(and many more)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
* The XEN_BALLOON code requires the balloon infrastructure that is not
getting built on ARM.
* The tmem hypercall is not available on ARM
* ARMv6 does not support cmpxchg on 16-bit words that are used in the
Xen grant table code, so we must ensure that Xen support is only
built on ARMv7-only kernels not combined ARMv6/v7 kernels.
* sys-hypervisor.c needs to include linux/err.h in order to use the
IS_ERR/PTR_ERR/ERR_PTR family of functions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: xen-devel@lists.xensource.com
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
read_current_timer is used by get_cycles since "ARM: 7538/1: delay:
add registration mechanism for delay timer sources", and get_cycles
can be used by device drivers in loadable modules, so it has to
be exported.
Without this patch, building imote2_defconfig fails with
ERROR: "read_current_timer" [crypto/tcrypt.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Jonathan Austin <jonathan.austin@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
One such warning was recently fixed in a761cebf "ARM: Fix build warning
in arch/arm/mm/alignment.c" but only for the thumb2 case, this fixes
the other half.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: error: 'offset.un' may be used uninitialized in this function
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The recently added Emma Mobile GPIO driver calls set_irq_flags
and irq_set_chip_and_handler for the interrupts it exports and
it can be built as a module, which currently fails with
ERROR: "set_irq_flags" [drivers/gpio/gpio-em.ko] undefined!
We either need to replace the call to set_irq_flags with something
else or export that function. This patch does the latter.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The mls instruction is not available in ARMv6K or below, so we
should make the test conditional on at least ARMv7. ldrexd/strexd
are available in ARMv6K or ARMv7, which we can test by checking
the CONFIG_CPU_32v6K symbol.
/tmp/ccuMTZ8D.s: Assembler messages:
/tmp/ccuMTZ8D.s:22188: Error: selected processor does not support ARM mode `mls r0,r1,r2,r3'
/tmp/ccuMTZ8D.s:22222: Error: selected processor does not support ARM mode `mlshi r7,r8,r9,r10'
/tmp/ccuMTZ8D.s:22252: Error: selected processor does not support ARM mode `mls lr,r1,r2,r13'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Leif Lindholm <leif.lindholm@arm.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Both these features have been around for a long time now, and haven't
had any recent issues brought up. So lets drop their experimental
status.
In any case, hotplugis selected by other non-experimental options
which then cause a Kconfig warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The periodic mode is currently calculated by a simple division
but we should pay more attention to our integer arithmetics.
Also delete a comment that does not make any sense.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
When booting a secondary CPU, the primary CPU hands two sets of page
tables via the secondary_data struct:
(1) swapper_pg_dir: a normal, cacheable, shared (if SMP) mapping
of the kernel image (i.e. the tables used by init_mm).
(2) idmap_pgd: an uncached mapping of the .idmap.text ELF
section.
The idmap is generally used when enabling and disabling the MMU, which
includes early CPU boot. In this case, the secondary CPU switches to
swapper as soon as it enters C code:
struct mm_struct *mm = &init_mm;
unsigned int cpu = smp_processor_id();
/*
* All kernel threads share the same mm context; grab a
* reference and switch to it.
*/
atomic_inc(&mm->mm_count);
current->active_mm = mm;
cpumask_set_cpu(cpu, mm_cpumask(mm));
cpu_switch_mm(mm->pgd, mm);
This causes a problem on ARMv7, where the identity mapping is treated as
strongly-ordered leading to architecturally UNPREDICTABLE behaviour of
exclusive accesses, such as those used by atomic_inc.
This patch re-orders the secondary_start_kernel function so that we
switch to swapper before performing any exclusive accesses.
Cc: <stable@vger.kernel.org>
Cc: David McKay <david.mckay@st.com>
Reported-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The PERF_EVENT_IOC_PERIOD ioctl command can be used to change the
sample period of a running perf_event. Consequently, when calculating
the next event period, the new period will only be considered after the
previous one has overflowed.
This patch changes the calculation of the remaining event ticks so that
they are offset if the period has changed.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Andreas Sandberg <andreas.sandberg@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | | | |_|/ /
| | |/| | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Commit c564df4db85aac8d1d65a56176a0a25f46138064 (ARM: 7540/1: kexec:
Check segment memory addresses) added a safety check with accidentally
reversed condition, and broke kexec functionality on ARM. Fix this.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| | |\ \ \ \ \
| | |_|_|/ /
| |/| | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull CMA and DMA-mapping fixes from Marek Szyprowski:
"This consists mainly of a set of one-liner fixes and cleanups for a
few minor issues identified in both Contiguous Memory Allocator code
and ARM DMA-mapping subsystem."
* 'fixes_for_linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: mm: Remove unused arm_vmregion priv field
ARM: dma-mapping: fix build warning in __dma_alloc()
ARM: dma-mapping: support debug_dma_mapping_error
mm: cma: alloc_contig_range: return early for err path
drivers: cma: Fix wrong CMA selected region size default value
drivers: dma-coherent: Fix typo in dma_mmap_from_coherent documentation
drivers: dma-contiguous: Don't redefine SZ_1M
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Commit e9da6e9905e639b0f842a244bc770b48ad0523e9 ("ARM: dma-mapping:
remove custom consistent dma region") removed the last users of the
field. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Fix build warning in __dma_alloc() as below:
arch/arm/mm/dma-mapping.c: In function '__dma_alloc':
arch/arm/mm/dma-mapping.c:653:29: warning: 'page' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
| | | | |_|/
| | |/| |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Without the patch, kind of below warning will be dumped if DMA-API
debug is enabled:
[ 11.069763] ------------[ cut here ]------------
[ 11.074645] WARNING: at lib/dma-debug.c:948 check_unmap+0x770/0x860()
[ 11.081420] ehci-omap ehci-omap.0: DMA-API: device driver failed to
check map error[device address=0x0000000
0adb78e80] [size=8 bytes] [mapped as single]
[ 11.095611] Modules linked in:
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen bug-fixes from Konrad Rzeszutek Wilk:
- Fix mysterious SIGSEGV or SIGKILL in applications due to corrupting
of the %eip when returning from a signal handler.
- Fix various ARM compile issues after the merge fallout.
- Continue on making more of the Xen generic code usable by ARM
platform.
- Fix SR-IOV passthrough to mirror multifunction PCI devices.
- Fix various compile warnings.
- Remove hypercalls that don't exist anymore.
* tag 'stable/for-linus-3.7-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: dbgp: Fix warning when CONFIG_PCI is not enabled.
xen: arm: comment on why 64-bit xen_pfn_t is safe even on 32 bit
xen: balloon: use correct type for frame_list
xen/x86: don't corrupt %eip when returning from a signal handler
xen: arm: make p2m operations NOPs
xen: balloon: don't include e820.h
xen: grant: use xen_pfn_t type for frame_list.
xen: events: pirq_check_eoi_map is X86 specific
xen: XENMEM_translate_gpfn_list was remove ages ago and is unused.
xen: sysfs: fix build warning.
xen: sysfs: include err.h for PTR_ERR etc
xen: xenbus: quirk uses x86 specific cpuid
xen PV passthru: assign SR-IOV virtual functions to separate virtual slots
xen/xenbus: Fix compile warning.
xen/x86: remove duplicated include from enlighten.c
|
| | | |\ \ \ \
| | | | |/ /
| | | |/| |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
* commit 'v3.7-rc1': (10892 commits)
Linux 3.7-rc1
x86, boot: Explicitly include autoconf.h for hostprogs
perf: Fix UAPI fallout
ARM: config: make sure that platforms are ordered by option string
ARM: config: sort select statements alphanumerically
UAPI: (Scripted) Disintegrate include/linux/byteorder
UAPI: (Scripted) Disintegrate include/linux
UAPI: Unexport linux/blk_types.h
UAPI: Unexport part of linux/ppp-comp.h
perf: Handle new rbtree implementation
procfs: don't need a PATH_MAX allocation to hold a string representation of an int
vfs: embed struct filename inside of names_cache allocation if possible
audit: make audit_inode take struct filename
vfs: make path_openat take a struct filename pointer
vfs: turn do_path_lookup into wrapper around struct filename variant
audit: allow audit code to satisfy getname requests from its names_list
vfs: define struct filename and have getname() return it
btrfs: Fix compilation with user namespace support enabled
userns: Fix posix_acl_file_xattr_userns gid conversion
userns: Properly print bluetooth socket uids
...
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
