aboutsummaryrefslogtreecommitdiffstats
path: root/arch/sh/mm
Commit message (Collapse)AuthorAge
* sh: intc - add support for sh7619Magnus Damm2007-09-20
| | | | | | | | | This patch converts the cpu specific interrupt setup code for sh7619 from ipr to intc. New vectors are also added to match the information provided by the datasheet. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Add SH7720 CPU support.Markus Brunner2007-09-20
| | | | | | | | This adds support for the SH7720 (SH3-DSP) CPU. Signed-off by: Markus Brunner <super.firetwister@gmail.com> Signed-off by: Mark Jonas <toertel@gmail.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Bump up NODES_SHIFT for SH-X3.Paul Mundt2007-09-20
| | | | | | | This was at 1, which is where most subtypes want it. SH-X3 has more nodes, so bump it up to 3. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: remove intc2 codeMagnus Damm2007-09-20
| | | | | | | There is no point in keeping around the now unused intc2 code. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Initial multiple-node support for SH-X3.Paul Mundt2007-09-20
| | | | | | Wire up CPU#0 URAM as node 1 on SH-X3. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for x3Magnus Damm2007-09-20
| | | | | | | | | | | This patch converts the cpu specific interrupt setup code for x3 from intc2 to intc. New vectors are also added to match the preliminary information. Use plat_irq_setup_pins() to select between IRQ and IRL mode for IRQ0-3. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix cache disabling build failures on nommu.Paul Mundt2007-09-20
| | | | | | | The cache disabling stuff screwed up some of the sh4 nommu builds, fix it up again. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for SH7760Magnus Damm2007-09-20
| | | | | | | | | | | | | | | | This patch converts the cpu specific interrupt setup code for sh7760 from ipr + intc2 to intc. New vectors are also added to match the information provided by the datasheet. Vectors for IRQ4-IRQ7 are enabled by default. Use plat_irq_setup_pins() if pins IRL0-3 should be used in IRLM mode. The patch also adds the SIM block to the serial port platform data. Version two of this patch fixes MMCIF problems reported by Manuel Lauss. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for SH7785Magnus Damm2007-09-20
| | | | | | | | | | | | This patch converts the cpu specific interrupt setup code for sh7785 from intc2 to intc. New vectors are also added to match the information provided by the datasheet. No IRQ/IRL pin vectors are enabled by default. Use plat_irq_setup_pins() to select between IRL and IRQ mode. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Support explicit L1 cache disabling.Paul Mundt2007-09-20
| | | | | | | | | This reworks the cache mode configuration in Kconfig, and allows for explicit selection of write-back/write-through/off configurations. All of the cache flushing routines are optimized away for the off case. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for SH7706, SH7707, SH7708, SH7709Magnus Damm2007-09-20
| | | | | | | | | | | | | | | | | | | This patch unifies the cpu specific interrupt setup code for sh7706, sh7707, sh7708 and sh7709 and moves the code into a new file called setup-sh770x.c. It makes sense to share the setup code between these processors because most hardware blocks are identical from a software point of view. With this patch the sh770x processors now have a complete set of vectors that match with the information provided by the data sheets. This is a big improvement for sh7708. Vectors for IRQ4 and IRQ5 are enabled by default. Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode. This patch also unifies the platform device setup code which means that the rtc driver now has platform data for all sh770x processors. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for SH7710Magnus Damm2007-09-20
| | | | | | | | | | | | | | | | | This patch converts the cpu specific interrupt setup code for sh7710 from ipr to intc. While at it new vectors are added to match the information provided by the datasheet. Version two simplifies the Kconfig part. Vectors for IRQ4 and IRQ5 are enabled by default. Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode. This patch also adds sh7710 specific platform data for the rtc driver. The base address of SCIF1 is adjusted to match the datasheet. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for SH7705Magnus Damm2007-09-20
| | | | | | | | | | | | | | | This patch converts the cpu specific interrupt setup code for sh7705 from ipr to intc. While at it new vectors are added to match the information provided by the datasheet. Vectors for IRQ4 and IRQ5 are enabled by default. Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode. This patch also adds sh7705 specific platform data for the rtc driver. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix pgd mismatch from cached TTB in unhandled fault.Paul Mundt2007-08-01
| | | | | | | | | | | When reading the cached TTB value and extracting the pgd, we accidentally applied a __va() to it and bumped it off in to bogus space which ended up causing multiple faults in the error path. Fix it up so unhandled faults don't do strange and highly unorthodox things when oopsing. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Don't include fault-nommu on SH-2/SH-2A.Paul Mundt2007-08-01
| | | | | | | | | | fault-nommu defines the page fault handler stubs for SH-3/4 parts, but is not needed on SH-2/SH-2A now that the entry code has been logically separated. Add it in for SH-3 and SH-4 explicitly. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix irqflags tracing for SH-3/4 nommu.Paul Mundt2007-08-01
| | | | | | | | | We were missing the trace_hardirqs_on() instrumentation in the nommu case, resync with the MMU version of the page fault handler to have this behaving consistently. Also explicitly re-enable IRQs now that the assembly code isn't doing it for us any more. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix fs.h removal from mm.h regressions.Paul Mundt2007-07-31
| | | | Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: remove support for sh7300 and solution engine 7300Magnus Damm2007-07-26
| | | | | | | | | This patch removes old dead code: - kill off sh7300 cpu support - get rid of broken solution engine 7300 board support Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Restrict DSP support to specific CPUs.Paul Mundt2007-07-26
| | | | | | | | | Not all CPUs support the DSP, and this leads to problems when mixing and matching CPU types and DSP opcodes. Fix this up by only allowing CONFIG_SH_DSP to be enabled for the CPUs that explicitly have such a block. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: remove support for sh73180 and solution engine 73180Magnus Damm2007-07-24
| | | | | | | | | This patch removes old dead code: - kill off sh73180 cpu support - get rid of broken solution engine 73180 board support Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: remove old broken pint codeMagnus Damm2007-07-24
| | | | | | | | | The code in arch/sh/kernel/cpu/irq/pint.c doesn't compile, so let's get rid of it to make space for a future pint implementation on top of intc. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Reclaim beginning of P3 space for vmalloc area.Paul Mundt2007-07-24
| | | | | | | | The first 1MB of P3 space was reserved and used for page colouring, as we've reworked that to use fixmaps, we can reclaim the space and hand it back to VMALLOC_START. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Add kmap_coherent()/kunmap_coherent() interface for SH-4.Paul Mundt2007-07-24
| | | | | | | | | | | | | This wires up kmap_coherent() and kunmap_coherent() on SH-4, and moves away from the p3map_mutex and reserved P3 space, opting to use fixmaps for colouring instead. The copy_user_page()/clear_user_page() implementations are moved to this, which fixes the nasty blowups with spinlock debugging as a result of having some of these calls nested under the page table lock. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for SH7750 and its variantsMagnus Damm2007-07-20
| | | | | | | | | | | | | This patch converts the cpu specific 7750 setup code to use the new intc controller. Many new vectors are added and multiple processor variants including 7091, 7750, 7750s, 7750r, 7751 and 7751r should all have the correct vectors hooked up. IRLM interrupts can be enabled using ipr_irq_enable_irlm() which now is marked as __init. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for 7780Magnus Damm2007-07-19
| | | | | | | | | | | | | | | | This patch converts the cpu specific 7780 setup code to use the new intc controller. Many new vectors are added and also support for external interrupt sense configuration. So with this patch it is now possible to configure external interrupt pins as edge or level triggered using set_irq_type(). No external interrupts are registered by default. Use plat_irq_setup_pins() to select between IRQ or IRL mode. This patch also fixes the Alarm IRQ for the RTC. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: intc - add support for 7722 processorMagnus Damm2007-07-19
| | | | | | | | | | | This patch converts the cpu specific 7722 setup code to use the new intc controller. Many new vectors are added and also support for external interrupt sense configuration. So with this patch it is now possible to configure external interrupt pins as edge or level triggered using set_irq_type(). Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* mm: Remove slab destructors from kmem_cache_create().Paul Mundt2007-07-19
| | | | | | | | | | | | | | Slab destructors were no longer supported after Christoph's c59def9f222d44bb7e2f0a559f2906191a0862d7 change. They've been BUGs for both slab and slub, and slob never supported them either. This rips out support for the dtor pointer from kmem_cache_create() completely and fixes up every single callsite in the kernel (there were about 224, not including the slab allocator definitions themselves, or the documentation references). Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* mm: fault feedback #2Nick Piggin2007-07-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch completes Linus's wish that the fault return codes be made into bit flags, which I agree makes everything nicer. This requires requires all handle_mm_fault callers to be modified (possibly the modifications should go further and do things like fault accounting in handle_mm_fault -- however that would be for another patch). [akpm@linux-foundation.org: fix alpha build] [akpm@linux-foundation.org: fix s390 build] [akpm@linux-foundation.org: fix sparc build] [akpm@linux-foundation.org: fix sparc64 build] [akpm@linux-foundation.org: fix ia64 build] Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ian Molton <spyro@f2s.com> Cc: Bryan Wu <bryan.wu@analog.com> Cc: Mikael Starvik <starvik@axis.com> Cc: David Howells <dhowells@redhat.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Hirokazu Takata <takata@linux-m32r.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Greg Ungerer <gerg@uclinux.org> Cc: Matthew Wilcox <willy@debian.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp> Cc: Richard Curnow <rc@rc0.org.uk> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp> Cc: Chris Zankel <chris@zankel.net> Acked-by: Kyle McMartin <kyle@mcmartin.ca> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Acked-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> [ Still apparently needs some ARM and PPC loving - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* sh: Select IPR-IRQ for SH7091.Paul Mundt2007-07-06
| | | | | | Fixes a compile failure for the Dreamcast. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Preliminary support for the SH-X3 CPU.Paul Mundt2007-06-20
| | | | | | This adds basic support for UP SH-X3. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Check oops_may_print() in unhandled fault.Paul Mundt2007-06-18
| | | | | | | Only print out pgd/pte data in the oops path if oops_may_print() holds true. Follows the i386 implementation. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Only support PMB for SH-X cores.Paul Mundt2007-06-15
| | | | | | | We don't have a PMB for SH-X2 or later, so only enable it for the few CPUs that support it. Fixes up the boot for SH4AL-DSP. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Kill off broken dma page ops.Paul Mundt2007-06-11
| | | | | | | | There's no point in keeping these around, they've been broken for some time, and the dmaenging/async_tx framework provides a far more reasonable interface. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Tidy up dependencies for SH-2 build.Paul Mundt2007-06-11
| | | | | | | | | | | | SH-2 can presently get in to some pretty bogus states, so we tidy up the dependencies a bit and get it all building again. This gets us a bit closer to a functional allyesconfig and allmodconfig, though there are still a few things to fix up. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Kill off dead SH7604 support.Paul Mundt2007-06-07
| | | | | | | | This was added during 2.5.x, but was never moved along. This can easily be resurrected if someone has one they wish to work with, but it's not worth keeping around in its current form. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: memory hot-add for sparsemem users support.Paul Mundt2007-06-07
| | | | | | | This enables simple hotplug support for sparsemem users. Presently this only permits memory being added in to node 0 on ZONE_NORMAL. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Make NUMA depend on sparsemem.Paul Mundt2007-06-07
| | | | | | | The only platforms that are supporting NUMA are doing so via sparsemem, so update the dependency. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: URAM node support for SH7722.Paul Mundt2007-06-07
| | | | | | | | This adds the URAM block on SH7722 as a separate node. Sparsemem is required for this, or it can simply be disabled by explicitly selecting a flatmem model. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Support for multiple nodes.Paul Mundt2007-06-07
| | | | | | | | | This adds basic support for multiple nodes on SH machines. This is primarily useful for boards with many different memory blocks that are otherwise unused (SH7722/SH7785 URAM and so forth). Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Use asm/sections.h for linker section symbols.Paul Mundt2007-06-07
| | | | | | Kill off a bunch of externs, and use sections.h instead.. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix up max_zone_pfns[] with multiple nodes.Paul Mundt2007-06-07
| | | | | | | | Currently using multiple nodes tramples the ZONE_NORMAL max low pfn, tidy up the logic a bit to get it all working as expected. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Enable IPR-IRQ for SH7206.Paul Mundt2007-06-07
| | | | Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: sparsemem support.Paul Mundt2007-06-07
| | | | | | | | This implements basic sparsemem support for SH. Presently this only uses static sparsemem, and we still permit explicit selection of flatmem. Those boards that want sparsemem can select it as usual. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix SH-4 CPU selects.Paul Mundt2007-06-07
| | | | | | | | | Now that select no longer works for selecting the "closest" CPU, we have to explicitly reference the precise sub-type in the few places where it actually matters (presently only setup code and some legacy sh-sci cruft). Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Rework CPU/board dependencies.Paul Mundt2007-06-07
| | | | | | | | | This was a big mess, rework the logic a bit so that we constrain to a particular subtype and figure out the board support based on that. This makes building subtype specific kernels supporting multiple boards possible again. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: ioremap() through PMB needs asm/mmu.h.Paul Mundt2007-06-03
| | | | Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix page size alignment in __copy_user_page().Paul Mundt2007-05-21
| | | | | | | | | | | SH-3 comes up with the PAGE_SIZE on a misaligned boundary: arch/sh/mm/copy_page.S: Assembler messages: arch/sh/mm/copy_page.S:132: Warning: misaligned data fix it up with explicit alignment. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fix up various compile warnings for SE boards.Paul Mundt2007-05-21
| | | | | | | | | | | | - setup-sh7750.c only defines the sh7751_ipr_map when building with SH7751 support. - 7722 Solution Engine was missing a mach-type entry, causing the macro in cf-enabler to be undefined. - arch/sh/mm/init.c needs linux/pagemap.h. Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: revert addition of page fault notifiersChristoph Hellwig2007-05-21
| | | | | | | | | | | | Just at the time you added them on sh we're removing them from other architectures. As there's no user yet this patch just removes them completely. Once you actually have a kprobes patch it should follow the direct call to kprobes_fault_handler model that powerpc, s390 and sparc64 employ in 2.6.22-rc1 and that I'm updating other architectures to. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* spelling fixes: arch/sh/Simon Arlott2007-05-21
| | | | | | | Spelling fixes in arch/sh/. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-21 12:25:50 -0500