aboutsummaryrefslogtreecommitdiffstats
path: root/arch/powerpc/boot
Commit message (Collapse)AuthorAge
* powerpc: Fix PCI in Holly device treeDavid Gibson2008-09-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | The PCI bridge on the Holly board is incorrectly represented in the device tree. The current device tree node for the PCI bridge sits under the tsi-bridge node. That's not obviously wrong, but the PCI bridge translates some PCI spaces into CPU address ranges which were not translated by the "ranges" property in tsi-bridge node. We used to get away with this problem because the PCI bridge discovery code was also buggy, assuming incorrectly that PCI host bridge nodes were always directly under the root bus and treating the translated addresses as raw CPU addresses, rather than parent bus addresses. This has since been fixed, thus breaking Holly. This could be fixed by adding extra translations to the tsi-bridge node, but this patch instead moves the Holly PCI bridge out of the tsi-bridge node to the root bus. This makes the tsi-bridge node represent only the built-in IO devices in the bridge, with a more-or-less contiguous address range. This is the same convention used on Freescale SoC chips, where the "soc" node represents only the IMMR region, and the PCI and other bus bridges are separate nodes under the root bus. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* powerpc: Holly board needs dtbImage targetJosh Boyer2008-09-17
| | | | | | | | | | | | | | | One of the changes in the bootwrapper makefile introduced the dtbImage targets for boards that need a simple zImage with a DTB embedded in them (595be948cce574ff2d5dde5d0426a636a4363c70, "[POWERPC] bootwrapper: Build multiple cuImages"). When this was done, it broke booting on the Holly board as the zImage.holly wrapper did not get the DTB embedded properly. This changes the target for the Holly board to a dtbImage so that the wrapper includes the vmlinux, wrapper bits, and DTB. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Fix interrupt values for DMA2 in MPC8610 HPCD device treeTimur Tabi2008-09-16
| | | | | | | | | | | | | | | For Freescale 8xxx devices that use an MPIC, the interrupt numbers in the device tree must be 16 greater than the values documented in the reference manual. In these chips, the MPIC is wired to use the first 16 numbers for external interrupts, but the documentation numbers internal interrupts from 0. In the MPC8610 HPCD device tree, the interrupt properties for the DMA channels for DMA2 were not the adjusted values. This fixes that. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Fix rare boot build breakageHugh Dickins2008-09-08
| | | | | | | | | | | | | | | A make -j20 powerpc kernel build broke a couple of months ago saying: In file included from arch/powerpc/boot/gunzip_util.h:13, from arch/powerpc/boot/prpmc2800.c:21: arch/powerpc/boot/zlib.h:85: error: expected ‘:’, ‘,’, ‘;’, ‘}’ or ‘__attribute__’ before ‘*’ token arch/powerpc/boot/zlib.h:630: warning: type defaults to ‘int’ in declaration of ‘Byte’ arch/powerpc/boot/zlib.h:630: error: expected ‘;’, ‘,’ or ‘)’ before ‘*’ token It happened again yesterday: too rare for me to confirm the fix, but it looks like the list of dependants on gunzip_util.h was incomplete. Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc: Add cuImage.mpc866ads to the bootwrapper as a cuboot-8xx targetScott Wood2008-08-21
| | | | | | | | | | | | | | | | | | This patch fixes the following build error with mpc866_ads_defconfig: <-- snip --> ... WRAP arch/powerpc/boot/cuImage.mpc866ads powerpc64-linux-ld: arch/powerpc/boot/cuboot-mpc866ads.o: No such file: No such file or directory make[2]: *** [arch/powerpc/boot/cuImage.mpc866ads] Error 1 <-- snip --> Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: TQM8548: DTS file fixes and cleanupWolfgang Grandegger2008-08-21
| | | | | | | | | Due to the missing compatible property for the SOC, the MPC I2C buses are not found any more. This patch fixes this issue. Furthermore it corrects the name of the SOC node and adds the missing I2C node for the RTC. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc: Fix whitespace merge in mpc8641 hpcn device treeKumar Gala2008-08-21
| | | | | | | | | | | When we coverted the .dts to v1 we lost a space between the irq and its polarity/sense information. This causes a bit of chaos as the reset of the blob is off by one cell. This was noticed by booting and getting errors w/ATA due to lock of interrupts. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Merge branch 'merge' of ↵Linus Torvalds2008-08-11
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: powerpc: Remove include/linux/harrier_defs.h powerpc: Do not ignore arch/powerpc/include powerpc: Delete completed "ppc removal" task from feature removal file powerpc/mm: Fix attribute confusion with htab_bolt_mapping() powerpc/pci: Don't keep ISA memory hole resources in the tree powerpc: Zero fill the return values of rtas argument buffer powerpc/4xx: Update defconfig files for 2.6.27-rc1 powerpc/44x: Incorrect NOR offset in Warp DTS powerpc/44x: Warp DTS changes for board updates powerpc/4xx: Cleanup Warp for i2c driver changes. powerpc/44x: Adjust warp-nand resource end address
| * powerpc/44x: Incorrect NOR offset in Warp DTSSean MacLennan2008-08-04
| | | | | | | | | | | | | | | | FPGA offset in NOR flash was converted incorrectly when switching from 64M to 4M flash. Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
| * powerpc/44x: Warp DTS changes for board updatesSean MacLennan2008-08-04
| | | | | | | | | | | | | | | | | | | | Added support for the new at24 eeprom driver. Documented a new fpga section, the DMA scatter gather list. Removed index from i2c. No longer needed. Fixed the leds section. Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* | powerpc: 86xx: mpc8610_hpcd: add watchdog nodeAnton Vorontsov2008-08-05
|/ | | | | | | | | | Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Wim Van Sebroeck <wim@iguana.be> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* powerpc: Move include files to arch/powerpc/include/asmStephen Rothwell2008-08-03
| | | | | | | | | | | | | | from include/asm-powerpc. This is the result of a mkdir arch/powerpc/include/asm git mv include/asm-powerpc/* arch/powerpc/include/asm Followed by a few documentation/comment fixups and a couple of places where <asm-powepc/...> was being used explicitly. Of the latter only one was outside the arch code and it is a driver only built for powerpc. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
* powerpc/fsl: proliferate simple-bus compatibility to soc nodesKim Phillips2008-07-29
| | | | | | | | | | | | | | | add simple-bus compatible property to soc nodes for 83xx/85xx platforms that were missing them. Add same to platform probe code. This fixes SoC device drivers (such as talitos) to succeed in matching devices present in the soc node. also update mpc836x_rdk dts to new SEC bindings (overlooked in commit 3fd4473: powerpc/fsl: update crypto node definition and device tree instances). Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/boot: Change spaces to tabsAdrian Bunk2008-07-21
| | | | | | | | | | | | | | | | For C code spaces versus tabs is just a religious issue, but for Makefiles it actually matters. This patch fixes he following errors: /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:166: *** missing separator. Stop. /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/powerpc/boot/Makefile:171: *** missing separator. Stop. Since this was inside an ifdef DTC_GENPARSER it was not a problem unless someone wanted to regenerate the shipped generated files. Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* powerpc/86xx: mpc8610_hpcd - add support for ULI RTCAnton Vorontsov2008-07-16
| | | | | | | | | | | | The ULI "Super South Bridge" contains ISA bridge to the legacy devices, such as Super IO mouse/keyboard/floppy disk controllers, parallel port, i8259 interrupt controller and so on. i8259 is disabled on the MPC8610HPCD, and other peripherals are not traced out. So we use only RTC. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc7448: add alias list to DTS, clean out old chosen nodePaul Gortmaker2008-07-16
| | | | | | | | | | | | | | | | | The mpc7448hpc2 board doesn't have an alias block like most of the other modern eval boards have. We need this block in order to have u-boot be able to make use of the CONFIG_OF_STDOUT_VIA_ALIAS (vs. having a hard coded node) in the future. Also remove the old, redundant chosen node. Of all the modern Freescale eval boards (incl. 83xx, 85xx, 86xx) this is the only one which still has it. Its presence also breaks with some older versions of u-boot, like 1.3.1 -- which try and insert a second chosen node. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/mpc8313erdb: Add power management to the device tree.Scott Wood2008-07-16
| | | | | Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Merge commit 'gcl/gcl-next'Benjamin Herrenschmidt2008-07-14
|\
| * powerpc/mpc5121: Update device tree for MPC5121ADS evaluation boardJohn Rigby2008-07-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current device tree is only bare bones. This patch adds nodes to make it a complete tree for the MPC5121ads. Added nodes include: mbx - opengl coprocessor nfc - nand flash controller cpld-pic - on board cpld rtc clock - clock control pmc - power management control gpio mscan - can module i2c axe - audio coprocessor display - display interface unit mdio ethernet usb ioctl - pin config pata ac97 - PSC configured as AC97 pscfifo - psc fifo configuration dma pci Fix typo in header changing MDS to ADS. Add a compatible property of the form "fsl,mpc5121-..." to nodes missing one. Changed localbus compatible to fsl,mpc5121-localbus, this does not break anything because the only code that uses it finds it via the node name, not compatible. Signed-off-by: John Rigby <jrigby@freescale.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
| * powerpc/mpc5200: add missing MSCAN FDT nodes for TQM52xxWolfgang Grandegger2008-07-12
| | | | | | | | | | | | | | | | This patch adds the still missing FDT nodes for the MSCAN devices for the TQM52xx modules. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | Merge commit 'jwb/jwb-next'Benjamin Herrenschmidt2008-07-14
|\ \
| * | powerpc/440: Convert Virtex ML507 device tree to dts-v1Grant Likely2008-07-09
| | | | | | | | | | | | Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
| * | powerpc/bootwrapper: Allow user to specify additional default targetsGrant Likely2008-07-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is inconvenient to add additional default targets to the bootwrapper Makefile for each new board supported which just needs a different dts file. This change allows the defconfig to specify additional build targets. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
| * | powerpc/bootwrapper: add missing bit of simpleImage targetGrant Likely2008-07-04
| | | | | | | | | | | | | | | | | | | | | | | | The wrapper script is missing the bits needed for building generic simpleImage targets (targets which don't depend on any particular firmware interface and retrieve all their data from the device tree). Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
| * | powerpc/virtex: Fix booting of Xilinx FPGAs with 16550 for 405 and 440John Linn2008-07-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following changes add processing to initialize the Xilinx 16550 UART in the boot wrapper for Virtex targets without firmware. Normally the boot wrapper assumes that the serial port has already been initialized by firmware. The wrapper was also modified to add the 440 build. Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
| * | powerpc/virtex: add dts file for ML507 reference designJohn Linn2008-07-04
| |/ | | | | | | | | | | | | | | This new file adds support for the ML507 reference design. The ML507 uses the Virtex 5 FXT FPGA which embeds a ppc440 core. Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | powerpc/fsl: update crypto node definition and device tree instancesKim Phillips2008-07-14
| | | | | | | | | | | | | | | | | | | | delete obsolete device-type property, delete model property (use compatible property instead), prepend "fsl," to Freescale specific properties. Add nodes to device trees that are missing them, and fix broken property values in other trees. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/CPM: Add i2c pins to dts and board setupJochen Friedrich2008-07-14
| | | | | | | | | | | | | | | | | | | | | | | | Initialize I2C pins on boards with CPM1/CPM2 controllers and document the i2c bus in booting-without-of. The boards don't have any I2C chips connected to the I2C bus, so unless some external chips are connected to the boards, this code is just an example of setting everything else up. Signed-off-by: Jochen Friedrich <jochen@scram.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Add support for MPC8536DSKumar Gala2008-07-14
| | | | | | | | | | | | | | | | | | | | Add support for the MPC8536 process and MPC8536DS reference board. The MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe. The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and thus use the same drivers. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: TQM8548: add missing support for RTC and LM75Wolfgang Grandegger2008-07-14
| | | | | | | | | | | | | | | | It adds the missing RTC node to tqm8548.dts and enables support for I2C, DS1307 and LM75 in the default configuration. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/86xx: mpc8610_hpcd: fix interrupt trigger type for ULi IDEAnton Vorontsov2008-07-14
| | | | | | | | | | | | | | | | | | | | | | | | i8259 PIC is disabled on MPC8610HPCD, and ULi IDE is configured to use PCI sideband interrupt that is specified in the device tree. Current HPCD's device tree specify that IDE interrupt is low to high sensitive, but in practice ULi IDE throws active-high interrupts (not active-low as all normal PCI devices). Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | powerpc/85xx: Fix KSI8560 .dtsKumar Gala2008-07-14
| | | | | | | | | | | | | | Rename MPIC label to mpic to match all other 85xx .dts and to fix compile issue introduced by addition of the DMA node. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | Merge commit 'origin/HEAD' into test-mergeBenjamin Herrenschmidt2008-07-14
|\ \ | | | | | | Manual fixup of include/asm-powerpc/pgtable-ppc64.h
| * | powerpc/bootwrapper: update for initrd with simpleImageJohn Linn2008-07-01
| | | | | | | | | | | | | | | | | | | | | This change to the makefile corrects the build of a simpleImage with initrd. Signed-off-by: John Linn <john.linn@xilinx> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* | | ibm_newemac: Parameterize EMAC Multicast Match HandlingGrant Erickson2008-07-09
| |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Various instances of the EMAC core have varying: 1) number of address match slots, 2) width of the registers for handling address match slots, 3) number of registers for handling address match slots and 4) base offset for those registers. As the driver stands today, it assumes that all EMACs have 4 IAHT and GAHT 32-bit registers, starting at offset 0x30 from the register base, with only 16-bits of each used for a total of 64 match slots. The 405EX(r) and 460EX now use the EMAC4SYNC core rather than the EMAC4 core. This core has 8 IAHT and GAHT registers, starting at offset 0x80 from the register base, with ALL 32-bits of each used for a total of 256 match slots. This adds a new compatible device tree entry "emac4sync" and a new, related feature flag "EMAC_FTR_EMAC4SYNC" along with a series of macros and inlines which supply the appropriate parameterized value based on the presence or absence of the EMAC4SYNC feature. The code has further been reworked where appropriate to use those macros and inlines. In addition, the register size passed to ioremap is now taken from the device tree: c4 for EMAC4SYNC cores 74 for EMAC4 cores 70 for EMAC cores rather than sizeof (emac_regs). Finally, the device trees have been updated with the appropriate compatible entries and resource sizes. This has been tested on an AMCC Haleakala board such that: 1) inbound ICMP requests to 'haleakala.local' via MDNS from both Mac OS X 10.4.11 and Ubuntu 8.04 systems as well as 2) outbound ICMP requests from 'haleakala.local' to those same systems in the '.local' domain via MDNS now work. Signed-off-by: Grant Erickson <gerickson@nuovations.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* | powerpc/bootwrapper: Pad .dtb by defaultKumar Gala2008-06-30
| | | | | | | | | | | | | | | | | | | | Since most bootloaders or wrappers tend to update or add some information to the .dtb they a handled they need some working space to do that in. By default add 1K of padding via a default setting of DTS_FLAGS. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* | powerpc: Change the default link address for pSeries zImage kernelsTony Breeds2008-06-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently we set the start of the .text section to be 4Mb for pSeries. In situations where the zImage is > 8Mb we'll fail to boot (due to overlapping with OF). Move .text in a zImage from 4MB to 64MB (well past OF). We still will not be able to load large zImage unless we also move OF, to that end, add a note to the zImage ELF to move OF to 32Mb. If this is the very first kernel booted then we'll need to move OF manually by setting real-base. Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
* | Merge branch 'linux-2.6'Paul Mackerras2008-06-29
|\|
| * [POWERPC] Fix bootwrapper builds with newer gcc versionsKumar Gala2008-06-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | GCC 4.4.x looks to be adding support for generating out-of-line register saves/restores based on: http://gcc.gnu.org/ml/gcc-patches/2008-04/msg01678.html This breaks the bootwrapper as we'd need to link with libgcc to get the implementation of the register save/restores. To workaround this issue, we just stole the save/restore code from gcc and simplified it down for our needs (integer only). Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * Merge branch 'for-2.6.26' of ↵Paul Mackerras2008-06-16
| |\ | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into merge
| | * [POWERPC] 83xx: MPC837xRDB's VSC7385 ethernet switch isn't on the MDIO busAnton Vorontsov2008-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MDIO-less PHYs should use CONFIG_FIXED_PHY driver and appropriate fixed-link property in the device tree. If not, ethernet will not work: e0024520:03 not found eth1: Could not attach to PHY IP-Config: Failed to open eth1 Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| | * [POWERPC] 85xx: MPC8548CDS - Fix size of PCIe IO spaceKumar Gala2008-06-09
| | | | | | | | | | | | | | | | | | | | | | | | Andrew Klossner pointed out the IO space size was in violation of the alignment requirements for windows on the 85xx. The size should have been 1M (to match u-boot). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | Merge branch 'next' of ↵Paul Mackerras2008-06-29
|\ \ \ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx
| * | | powerpc/4xx: Convert Sam440ep DTS to dts-v1Giuseppe Coviello2008-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This makes the sam440ep.dts dts-v1 compliant. Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
| * | | powerpc/4xx: Sam440ep supportGiuseppe Coviello2008-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sam440ep is an high customizable general purpose mini-itx board, based on the AMCC 440EP and with a LatticeXP FPGA onboard. It's poduced by ACube Systems Srl (Bassano del Grappa, Italy), http://www.acube-systems.biz. Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
| * | | powerpc/4xx: MTD support for the AMCC Taishan BoardImre Kaloz2008-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the NOR flash found on the AMCC Taishan Board and enable MTD support in the defconfig. Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* | | | powerpc: Add dma nodes to 83xx, 85xx and 86xx boardsKumar Gala2008-06-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Added DMA nodes for the elo/elo-plus DMA engines. Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that its the same as all the other boards. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | | powerpc/83xx: new board support: MPC8360E-RDKAnton Vorontsov2008-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is patch adds board file, device tree, and defconfig for the new board, made by Freescale Semiconductor Inc. and Logic Product Development. Currently supported: 1. UEC{1,2,7,4}; 2. I2C; 3. SPI; 4. NS16550 serial; 5. PCI and miniPCI; 6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85; 7. Graphics controller, Fujitsu MB86277. Not supported in this patch: 1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver); 2. FHCI USB (supported with FHCI driver). 3. QE Serial UCCs (tested to not work with ucc_uart driver, reason unknown, yet); 4. ADC AD7843 (tested to work, but support via device tree depends on major SPI rework, GPIO API, etc); Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | | powerpc/85xx: add local bus nodes for Flash and CAN to tqm8560.dtsWolfgang Grandegger2008-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds local bus nodes for Flash and CAN to the DTS file of the TQM8560 module (tqm8560.dts). Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* | | | powerpc/85xx: support for the TQM8548 module using the big FlashWolfgang Grandegger2008-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some TQM85xx boards could be equipped with up to 1 GiB (NOR) flash memory and therefore a modified memory map is required and setup by the board loader. This patch adds an appropriate DTS file. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>