aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm
Commit message (Collapse)AuthorAge
* arm: plat-orion: fix address decoding when > 4GB is usedThomas Petazzoni2013-03-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During the system initialization, the orion_setup_cpu_mbus_target() function reads the SDRAM address decoding registers to find out how many chip-selects of SDRAM have been enabled, and builds a small array with one entry per chip-select. This array is then used by device drivers (XOR, Ethernet, etc.) to configure their own address decoding windows to the SDRAM. However, devices can only access the first 32 bits of the physical memory. Even though LPAE is not supported for now, some Marvell boards are now showing up with 8 GB of RAM, configured using two SDRAM address decoding windows: the first covering the first 4 GB, the second covering the last 4 GB. The array built by orion_setup_cpu_mbus_target() has therefore two entries, and device drivers try to set up two address decoding windows to the SDRAM. However, in the device registers for the address decoding, the base address is only 32 bits, so those two windows overlap each other, and the devices do not work at all. This patch makes sure that the array built by orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows that correspond to the first 4 GB of the memory. To do that, it ignores the SDRAM decoding windows for which the 4 low-order bits are not zero (the 4 low-order bits of the base register are used to store bits 32:35 of the base address, so they actually indicate whether the base address is above 4 GB). This patch allows the newly introduced armada-xp-gp board to properly operate when it is mounted with more than 4 GB of RAM. Without that, all devices doing DMA (for example XOR and Ethernet) do not work at all. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* arm: mvebu: Reduce reg-io-width with UARTsHeikki Krogerus2013-03-08
| | | | | | | | | | | | | | | | | | | | | | Setting the reg-io-width to 1 byte represents more accurate description of the HW. This will fix an issue where UART driver causes kernel panic during bootup. Gregory CLEMENT traced the issue to autoconfig() in 8250.c, where the existence of FIFO is checked from UART_IIR register. The register is now read as 32-bit value as the reg-io-width is set to 4-bytes. The retuned value seems to contain bogus data for bits 31:8, causing the issue. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: Dove: add RTC device nodeJean-Francois Moine2013-03-08
| | | | | | | | | | | | The commit: 48be9ac ARM: Dove: split legacy and DT setup removed the RTC initialization. This patch re-enables the RTC via the DT. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* arm: mvebu: enable the USB ports on Armada 370 Reference Design boardFlorian Fainelli2013-03-08
| | | | | | | | This patch modifies the Armada 370 Reference Design DTS file to enable support for the two USB ports found on this board. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: dove: drop "select COMMON_CLK_DOVE"Paul Bolle2013-03-08
| | | | | | | | | | | Commit 5b03df9ace680d7cdd34a69dfd85ca5f74159d18 ("ARM: dove: switch to DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which makes this select statement a nop. It's probably a leftover of some experimental code that never hit mainline. Drop it. Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* rtc: rtc-mv: Add support for clk to avoid lockupsAndrew Lunn2013-03-08
| | | | | | | | | | | | | The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the driver clk_prepare_enable() this clock, otherwise there is a danger the SoC will lockup when accessing RTC registers with the clock disabled. Reported-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Simon Baatz <gmbnomis@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* gpio: mvebu: Add clk support to prevent lockupAndrew Lunn2013-03-08
| | | | | | | | | | | | | | The kirkwood SoC GPIO cores use the runit clock. Add code to clk_prepare_enable() runit, otherwise there is a danger of locking up the SoC by accessing the GPIO registers when runit clock is not ticking. Reported-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Simon Baatz <gmbnomis@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: fix to retain gbe MAC addresses for DT kernelsSebastian Hesselbarth2013-03-08
| | | | | | | | | | | | | | | | | The ethernet controller used on kirkwood looses its MAC address register contents when the corresponding clock is gated. As soon as mv643xx_eth is built as module, the clock gets gated and when loading the module, the MAC address is gone. Proper DT support for the mv643xx_eth driver is expected soon, so we add a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround is also already used on non-DT kirkwood kernels. Reported-by: Simon Baatz <gmbnomis@gmail.com> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Tested-by: Simon Baatz <gmbnomis@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* ARM: kirkwood: of_serial: fix clock gating by removing clock-frequencyJason Cooper2013-03-08
| | | | | | | | | | | | | | | | | | | | | | | | When DT support for kirkwood was first introduced, there was no clock infrastructure. As a result, we had to manually pass the clock-frequency to the driver from the device node. Unfortunately, on kirkwood, with minimal config or all module configs, clock-frequency breaks booting because of_serial doesn't consume the gate_clk when clock-frequency is defined. The end result on kirkwood is that runit gets gated, and then the boot fails when the kernel tries to write to the serial port. Fix the issue by removing the clock-frequency parameter from all kirkwood dts files. Booted on dreamplug without earlyprintk and successfully logged in via ttyS0. Reported-by: Simon Baatz <gmbnomis@gmail.com> Tested-by: Simon Baatz <gmbnomis@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* Merge branch 'for-linus' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds2013-03-03
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull late ARM updates from Russell King: "Here is the late set of ARM updates for this merge window; in here is: - The ARM parts of the broadcast timer support, core parts merged through tglx's tree. This was left over from the previous merge to allow the dependency on tglx's tree to be resolved. - A fix to the VFP code which shows up on Raspberry Pi's, as well as fixing the fallout from a previous commit in this area. - A number of smaller fixes scattered throughout the ARM tree" * 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: ARM: Fix broken commit 0cc41e4a21d43 corrupting kernel messages ARM: fix scheduling while atomic warning in alignment handling code ARM: VFP: fix emulation of second VFP instruction ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU ARM: 7654/1: Preserve L_PTE_VALID in pte_modify() ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock ARM: 7651/1: remove unused smp_timer_broadcast #define
| *-. Merge branches 'devel-stable', 'fixes' and 'mmci' into for-linusRussell King2013-03-02
| |\ \
| | * | ARM: Fix broken commit 0cc41e4a21d43 corrupting kernel messagesRussell King2013-03-01
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 0cc41e4a21d43 (arch: remove direct definitions of KERN_<LEVEL> uses) is broken - not enough thought was put into changing: .asciz "string" to .asciz "string1" "string2" The problem is that each string gets _separately_ NUL terminated, so the result is a string containing: "string1\0string2\0" rather than: "string1string2\0" With our new printk levels, this ends up as - eg, KERN_DEBUG "string": 0x01 0x00 0x07 0x00 "string" 0x00 which produces lots of \x01 in the kernel log. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: fix scheduling while atomic warning in alignment handling codeRussell King2013-02-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Paolo Pisati reports that IPv6 triggers this warning: BUG: scheduling while atomic: swapper/0/0/0x40000100 Modules linked in: [<c001b1c4>] (unwind_backtrace+0x0/0xf0) from [<c0503c5c>] (__schedule_bug+0x48/0x5c) [<c0503c5c>] (__schedule_bug+0x48/0x5c) from [<c0508608>] (__schedule+0x700/0x740) [<c0508608>] (__schedule+0x700/0x740) from [<c007007c>] (__cond_resched+0x24/0x34) [<c007007c>] (__cond_resched+0x24/0x34) from [<c05086dc>] (_cond_resched+0x3c/0x44) [<c05086dc>] (_cond_resched+0x3c/0x44) from [<c0021f6c>] (do_alignment+0x178/0x78c) [<c0021f6c>] (do_alignment+0x178/0x78c) from [<c00083e0>] (do_DataAbort+0x34/0x98) [<c00083e0>] (do_DataAbort+0x34/0x98) from [<c0509a60>] (__dabt_svc+0x40/0x60) Exception stack(0xc0763d70 to 0xc0763db8) 3d60: e97e805e e97e806e 2c000000 11000000 3d80: ea86bb00 0000002c 00000011 e97e807e c076d2a8 e97e805e e97e806e 0000002c 3da0: 3d000000 c0763dbc c04b98fc c02a8490 00000113 ffffffff [<c0509a60>] (__dabt_svc+0x40/0x60) from [<c02a8490>] (__csum_ipv6_magic+0x8/0xc8) Fix this by using probe_kernel_address() stead of __get_user(). Cc: <stable@vger.kernel.org> Reported-by: Paolo Pisati <p.pisati@gmail.com> Tested-by: Paolo Pisati <p.pisati@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: VFP: fix emulation of second VFP instructionRussell King2013-02-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Martin Storsjö reports that the sequence: ee312ac1 vsub.f32 s4, s3, s2 ee702ac0 vsub.f32 s5, s1, s0 e59f0028 ldr r0, [pc, #40] ee111a90 vmov r1, s3 on Raspberry Pi (implementor 41 architecture 1 part 20 variant b rev 5) where s3 is a denormal and s2 is zero results in incorrect behaviour - the instruction "vsub.f32 s5, s1, s0" is not executed: VFP: bounce: trigger ee111a90 fpexc d0000780 VFP: emulate: INST=0xee312ac1 SCR=0x00000000 ... As we can see, the instruction triggering the exception is the "vmov" instruction, and we emulate the "vsub.f32 s4, s3, s2" but fail to properly take account of the FPEXC_FP2V flag in FPEXC. This is because the test for the second instruction register being valid is bogus, and will always skip emulation of the second instruction. Cc: <stable@vger.kernel.org> Reported-by: Martin Storsjö <martin@martin.st> Tested-by: Martin Storsjö <martin@martin.st> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDROlof Johansson2013-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On multiplatform kernels, $MACHINE will be empty so there will be no default LOADADDR. Fail to build the uImage target unless one is provided by the developer at build time. Signed-off-by: Olof Johansson <olof@lixom.net> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()Catalin Marinas2013-02-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Following commit 26ffd0d4 (ARM: mm: introduce present, faulting entries for PAGE_NONE), if a page has been mapped as PROT_NONE, the L_PTE_VALID bit is cleared by the set_pte_ext() code. With LPAE the software and hardware pte share the same location and subsequent modifications of pte range (change_protection()) will leave the L_PTE_VALID bit cleared. This patch adds the L_PTE_VALID bit to the newprot mask in pte_modify(). Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Subash Patel <subash.rp@samsung.com> Tested-by: Subash Patel <subash.rp@samsung.com> Acked-by: Will Deacon <will.deacon@arm.com> Cc: <stable@vger.kernel.org> # 3.8.x Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| | * | ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clockNicolas Pitre2013-02-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When udelay() is implemented using an architected timer, it is wrong to scale loops_per_jiffy when changing the CPU clock frequency since the timer clock remains constant. The lpj should probably become an implementation detail relevant to the CPU loop based delay routine only and more confined to it. In the mean time this is the minimal fix needed to have expected delays with the timer based implementation when cpufreq is also in use. Reported-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Nicolas Pitre <nico@linaro.org> Tested-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| * | | ARM: 7651/1: remove unused smp_timer_broadcast #defineMark Rutland2013-02-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The assignment of clock_event_device::broadcast can be done by timer core as of 12ad100046: "clockevents: Add generic timer broadcast function", and the arm code moved over to this as of 3d06770eef: "arm: Add generic timer broadcast support", but left a dangling #define when !CONFIG_GENERIC_TIMER_BROADCAST. This patch removes the now unused #define. Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
| * | | Merge branch 'for-rmk/broadcast' of ↵Russell King2013-02-04
| |\ \ \ | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into devel-stable
* | \ \ \ Merge tag 'late-mvebu-rebased' of ↵Linus Torvalds2013-02-28
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC mvebu platform changes from Olof Johansson: "This series contains changes for the Marvell EBU platforms (mvebu, orion, kirkwood, dove) that were not part of the first set of pull requests because of dependencies on the MMC tree, and being submitted a little late. Notable changes are: - More devices get moved out of board files into device tree descriptions. The remaining devices listed in there have patches that will get sent for 3.10, after which we can remove a lot of the board files entirely. We are doing the pinctrl and mmc drivers here, ethernet and PCI still remain. - SMP support for mvebu is improved with support for the local interrupt controller. - The Guruplug board file gets replaced with a DT description. Unfortunately, the dependency on the MMC tree turned out to be a much larger problem than expected, when the MMC maintainer rebased the patches in his tree that all of the patches in this branch are based on, which caused merge conflicts between the new and old versions of those patches. To work around the merge conflicts, this branch rebases all patches on top of the respective MMC patches that did get merged into 3.9. The patches are all identical to the versions that were part of linux-next, but have a new commit date." * tag 'late-mvebu-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (90 commits) arm: mvebu: enable the SD card slot on Armada 370 Reference Design board ARM: kirkwood: topkick: init mvsdio via DT ARM: kirkwood: nsa310: convert to pinctrl ARM: Kirkwood: topkick: Enable i2c bus. ARM: kirkwood: topkick: convert to pinctrl ARM: dove: convert serial DT nodes to clocks property arm: mvebu: Add SPI flash on Armada 370 DB board arm: mvebu: Add SPI flash on Armada XP-DB board arm: mvebu: Add SPI flash on Armada XP-GP board arm: mvebu: Add support for SPI controller in Armada 370/XP clocksource: update and move armada-370-xp-timer documentation to timer directory arm: mvebu: update DT to support local timers ARM: Dove: convert usb host controller to DT arm: mvebu: Enable USB controllers on Armada 370/XP boards arm: mvebu: Add support for USB host controllers in Armada 370/XP arm: mvebu: add button for OpenBlocks AX3-4 ARM: Kirkwood: Convert NS2 to gpio-poweroff. ARM: Kirkwood: Convert NSA310 I2C to device tree ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driver ARM: Kirkwood: Convert NSA310 to DT based regulators. ...
| * | | | | arm: mvebu: enable the SD card slot on Armada 370 Reference Design boardFlorian Fainelli2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Armada 370 Reference Design board has one SD card slot, directly connected to the SDIO IP of the SoC, so we enable this IP. there are no GPIOs for card-detect and write-protect so we do not specify any. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: kirkwood: topkick: init mvsdio via DTJason Cooper2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Jason Cooper <jason@lakedaemon.net> Tested-by: Andrew Lunn <andrew@lunn.ch>
| * | | | | ARM: kirkwood: nsa310: convert to pinctrlJason Cooper2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: topkick: Enable i2c bus.Andrew Lunn2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a DT node for I2C and pinctrl hog for the pins. There appears to be an i2c bus on topkick with a device on it: i2cdetect 0 WARNING! This program can confuse your I2C bus, cause data loss and worse! I will probe file /dev/i2c-0. I will probe address range 0x03-0x77. Continue? [Y/n] y 0 1 2 3 4 5 6 7 8 9 a b c d e f 00: -- -- -- -- -- -- -- -- -- -- -- -- -- 10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 60: -- -- -- -- 64 -- -- -- -- -- -- -- -- -- -- -- 70: -- -- -- -- -- -- -- -- Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: kirkwood: topkick: convert to pinctrlJason Cooper2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: dove: convert serial DT nodes to clocks propertySebastian Hesselbarth2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | of_serial now has support for using clocks property and we have a DT clock provider. This patch replaces the hard coded clock-frequency property with a clocks phandle to tclk. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: Add SPI flash on Armada 370 DB boardGregory CLEMENT2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add support for the SPI flash MX25l25635E which is present on the Armada 370 DB board. This flash stores the bootloader and its environment. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: Add SPI flash on Armada XP-DB boardGregory CLEMENT2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add support for the SPI flash M25P64 which is present on the Armada XP DB board. This flash stores the bootloader and its environment. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: Add SPI flash on Armada XP-GP boardEzequiel Garcia2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds an SPI master device node for Armada XP-GP board. This master node is an SPI flash controller 'n25q128a13'. Since there is no 'partitions' node declared, one full sized partition named as the device will be created. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Lior Amsalem <alior@marvell.com> Tested-by: Gregory Clement <gregory.clement@free-electrons.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Acked-by: Gregory Clement <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: Add support for SPI controller in Armada 370/XPEzequiel Garcia2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Armada 370 and Armada XP SoC has an SPI controller. This patch adds support for this controller in Armada 370 and Armada XP SoC common device tree files. Note that the Armada XP SPI register length is 0x50 bytes, while Armada 370 SPI register length is 0x28 bytes, so we choose the smaller of the two. Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Lior Amsalem <alior@marvell.com> Acked-by: Gregory Clement <gregory.clement@free-electrons.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: update DT to support local timersGregory CLEMENT2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the time-armada-370-xp support local timers, updated the device tree to take it into account. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Dove: convert usb host controller to DTSebastian Hesselbarth2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With DT support for orion-ehci also convert Dove to it and remove the legacy calls and clock aliases. This patch is based on "ARM: Dove: split legacy and DT setup" applied to mvebu/boards recently. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: Enable USB controllers on Armada 370/XP boardsEzequiel Garcia2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch activates every USB port provided by each SoC. Except for Armada XP Openblocks AX3-4 board, where we enable only the first two USB ports until we have more information on the third one usage. Cc: Lior Amsalem <alior@marvell.com> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Gregory CLEMENT <gregory.clement@free-electrons.com> Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: Add support for USB host controllers in Armada 370/XPEzequiel Garcia2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Armada 370 and Armada XP SoC has an Orion EHCI USB controller. This patch adds support for this controller in Armada 370 and Armada XP SoC common device tree files. Cc: Lior Amsalem <alior@marvell.com> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Tested-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: add button for OpenBlocks AX3-4Thomas Petazzoni2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The OpenBlocks AX3-4 board has one software-controlled button on the front side, labeled "INIT", so we add minimal support for this button in the kernel. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: Convert NS2 to gpio-poweroff.Andrew Lunn2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove C code and add a Device Tree node in its place. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Simon Guinot <simon.guinot@sequanux.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: Convert NSA310 I2C to device treeAndrew Lunn2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a sub-node into the I2C node to represent the adt7476 device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: Convert NSA310 to use gpio-poweroff driverAndrew Lunn2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the C code and add a Device Tree node for gpio-poweroff. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: Convert NSA310 to DT based regulators.Andrew Lunn2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Dove: add fixed regulator for CuBox USB powerSebastian Hesselbarth2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CuBox needs to enable USB power on a gpio pin. Add a fixed regulator to always enable usb power on boot. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Dove: move CuBox led pinctrl to gpio-leds nodeSebastian Hesselbarth2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | gpio-leds has support for pinctrl allocation, make use of it. Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: Convert openblocks A6 board to pinctrlNobuhiro Iwamatsu2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: Add pinctrl of NAND to 88f6282Nobuhiro Iwamatsu2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | ARM: Kirkwood: Add pinctrl of TWSI1 to 88f6282Nobuhiro Iwamatsu2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 88f6282 has one more TWSI(TWSI1). This add the information to enable pinctl of TWSI1. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: kirkwood: add pinmux option for the SDIO interface on 88F6282Thomas Petazzoni2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds a pinmux option, pmx_sdio, to enable the muxing of the SDIO interface on the 88F6282 SoC from Marvell. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: kirkwood: mplcec4: use Device Tree to probe SDIOThomas Petazzoni2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the mvsdio driver has a Device Tree binding, and the SDIO controller is declared in kirkwood.dtsi, migrate the mplcec4 board to use the Device Tree to probe the SDIO controller and to mux the pins of the SDIO interface correctly. This patch has not been tested, it remains to be tested by a person having access to the hardware. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Stefan Peter <s.peter@mpl.ch> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: kirkwood: dreamplug: use Device Tree to probe SDIOThomas Petazzoni2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the mvsdio driver has a Device Tree binding, and the SDIO controller is declared in kirkwood.dtsi, migrate the dreamplug board to use the Device Tree to probe the SDIO controller and to mux this interface properly. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: kirkwood: add Device Tree informations for the SDIO controllerThomas Petazzoni2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that the SDIO controller has a Device Tree binding, let's use it in kirkwood.dtsi. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: enable the SDIO interface on the Globalscale MiraboxThomas Petazzoni2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Globalscale Mirabox uses the SDIO interface of the Armada 370 to connect to a Wifi/Bluetooth SD8787 chip, so we enable the SDIO interface of this board in its Device Tree file. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
| * | | | | arm: mvebu: enable the SD card slot on Armada 370 DB boardThomas Petazzoni2013-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Armada XP DB evaluation board has one SD card slot, directly connected to the SDIO IP of the SoC, so we add a device tree description for it. However, in the default configuration of the board, the SD card slot is not usable: the connector plugged into CON40 must be changed against a different one, provided with the board by the manufacturer. Since such a manual modification of the hardware is needed, we did not enable the SDIO interface by default, and left it to the board user to modify the Device Tree if needed. Since this board is really only an evaluation board for developers and not a final product, it is not too bad. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Jason Cooper <jason@lakedaemon.net>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-30 10:11:12 -0500