| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Harmony uses a TPS6586x regulator. Instantiate this, and hook up a
couple of fixed GPIO-controlled regulators too.
Based on Ventana regulator patch by Stephen Warren <swarren@nvidia.com>
and converted to Harmony.
swarren made the following changes:
* Added ldo0 regulator configuration to device tree, and updated
board-harmony-pcie.c for the new regulator name.
* Fixed vdd_1v05's voltage from 10.5V to 1.05V.
* Modified board-harmony-pcie.c to obtain the en_vdd_1v05 GPIO number at
run-time from device tree instead of hard-coding it.
* Removed board-harmony{-power.c,.h} now that they're unused.
* Disabled vdd_1v05 regulator; the code in board-harmony-pcie.c hijacks
this GPIO for now. This will be fixed when the PCIe driver is re-
written as a driver. The code can't regulator_get("vdd_1v05") right
now, because the vdd_1v05 regulator's probe gets deferred due to its
supply being the PMIC, which gets probed after the regulator the first
time around, and this dependency is only resolved by repeated probing,
which happens when deferred_probe_initcall() is called, which happens
in a late initcall, whose runtime order relative to harmony_pcie_init()
is undefined, since that's also called from a late initcall.
* Removed unused harmony_pcie_initcall().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Harmony can be booted using device tree with equal functionality as when
booted using a board file. Remove as much of the board file as is
possible, since it's no longer needed.
Two special-cases are still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet, and the Harmony .dts file
doesn't yet describe regulators which are needed for PCIe. This logic is
now enabled unconditionally rather than via CONFIG_MACH_HARMONY. While
this is more code than other boards, it's still unlikely to be much of a
problem, and both regulators and PCIe should be supported via device tree
in the near future, allowing the remaining code to be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Device have SYS rail which is always ON. It is system power bus. LDO5
and LDO_RTC get powered through this rail internally. Add support for
this rail and make the LDO5/LDO_RTC supply by it. Update document
accordingly.
[swarren: Instantiate the sys regulator from board-harmony-power.c to
avoid regression.]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit 3d55c29 "ARM: tegra: harmony: add regulator supply name and its
input supply" was supposed to fix all the problems with regulators on
Harmony. However, it appears that I only tested it when booting using
board files, not when booting using device tree. This change fixes two
problems with regulators when booting using device tree:
1) That patch only created the vdd_sys regulator when booting using a
board file. Since this is the root of the whole regulator tree, this
caused no regulators to successfully initialize when booting using
device tree. The registration of vdd_sys is moved to fix this.
2) When booting use DT, the regulator core sets has_full_constraints,
which in turn causes the core to turn off any regulators not marked
as always on. Some of the affected regulators are required for basic
system operation. To solve this, add always on constraints to all
relevant regulators. This doesn't affect booting using a board file
since nothing sets has_full_constraints in that case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Name the regulator as per board schematics and adds its
supply name info in regulator data.
Add the always on fixed regulator to refer the battery supply.
Use this fixed regulator for input supply of some of PMIC
regulator
This patch was originally part of a 2-patch series. Patch 2 got applied
to the regulator tree as 7c7fac3 "regulator: tps6586x: add support for
input supply" without this patch. This broke regulator support on
Harmony.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: added dependency info to commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There currently aren't bindings for the Tegra PCIe controller. Work on
this is in progress, but not yet complete. Manually initialize PCIe when
booting from device tree, in order to bring DT support to the same
feature level as board files, which will in turn allow board files to be
deprecated.
PCIe on Harmony requires various regulators to be registered and enabled
before initializing the PCIe controller. Note that since the I2C
controllers are instantiated from DT, we must use i2c_new_device() to
register the PMU rather than i2c_register_board_info().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
|
| | |
| |
| |
| |
| |
| |
| |
| | |
The new PMC driver now configures the PMU interrupt inversion, so board
files don't need to poke the PMC registers directly to achieve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| |/
|
|
|
|
|
|
| |
The PCIe reference clock needs a 3.3V supply voltage to work properly.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Without this, the PMC continually detects an interrupt when the PMU_IRQ
line is high, causing the tps6686x IRQ handler thread to hog an entire
CPU.
This change was originally written by Wei Ni <wni@nvidia.com> for Seaboard
in the ChromeOS kernel.
Long-term, this should probably be moved into some kind of PMU driver,
or perhaps integrated into the GPIO/IRQ/pinmux system?
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, both the WM8903 and TPS6586x chips attempt to register with
gpiolib using the same GPIO numbers. This causes the audio driver to
fail to initialize.
To solve this, add a define to board-harmony.h for the TPS6586x, and make
board-harmony-power.c use this define, instead of directly referencing
TEGRA_NR_GPIOS.
This fixes a regression introduced by commit
6f168f2fa60f87e85e0df25e87e2372f22f5eb7c.
ARM: tegra: harmony: initialize the TPS65862 PMIC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
|
|
|
Initialize the PMIC voltage regulators and provide the supply map for
PCI-e clock supply. The rest of the supplies should be added together
with the drivers that use them.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
