| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch from Andrew Victor
This patch includes a few changes to the clock support on the
AT91RM9200.
1. Added definitions for Ethernet, MMC, TWI, USARTs, and SPI peripheral
clocks.
2. Replaced some hard-coded hex values with the text definitions in
at91rm9200_sys.h.
3. If the USB96M bit is set for PLLB, then the rate of PLLB is not
affected but only the USB Host/Device clocks which are derived from it.
Issue reported by Sergei Sharonov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch from Andrew Victor
If the timer interrupt is ever significantly delayed (or after the
system was suspended), the system could spin incrementing the time for
too long.
The fix is to replace the "do {} while" with a "while {}".
Orignal patch by Savin Zlobec and Peter Menzebach.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
| |
In all current use cases, "chipdata" is used to store an iomem address.
Mark it with __iomem, and rename it to 'base'. Leave the accessor macros
alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Patch from Andrew Victor
disable_irq() lazily disables the interrupt, so the IRQ is only disabled
once the interrupt occurs again. The GPIO interrupt handler therefore
must first check disable_depth to see if the IRQ needs to be disabled.
Orignal patch by Bill Gatliff.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch from Andrew Victor
This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.
This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.
This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
Now that no code uses it anymore, mark it deprecated and remove all
initializations from the tree.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
#3244)
Patch from Andrew Victor
This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.
This patch is the support for the Cogent CSB337 and CSB637 boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Patch from Andrew Victor
This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.
This patch is the support for Atmel's DK and EK boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
Patch from SAN People
Following changes were made to clock.c:
1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.
Otherwise it's the same as the previous patch.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
