| Commit message (Collapse) | Author | Age |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
From Nicolas Ferre:
Device tree related fixes:
- USB host numbering for 9x5 which was preventing from using all ports
- a missing UART (not USART) clock lookup table was preventing from using
them on 9x5
- too large amount of memory was specified for 9n12ek
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/DT: fix at91sam9n12ek memory node
ARM: at91: add missing uart clocks DT entries
ARM: at91/DT: at91sam9x5ek: fix USB host property to enable port C
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.5+
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Add clocks to clock lookup table for uart DT entries.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Device Tree "num-ports" property of USB host node has to be
set to maximum number of ports available.
The possibility to activate a particular port is done by specifying the proper
gpio configuration for its vbus.
This patch fixes the USB host node by configuring the 3 ports available on the
product and letting "port A" available for USB gadget usage.
Reported-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Bo Shen <voice.shen@atmel.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
From Kukjin Kim:
Fix to boot kernel on exynos5440 which has no specific map_io(). Current kernel
cannot support no CPU specific map_io() for Samsung SoCs.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: fix to support for missing cpu specific map_io
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Since commit 7ed76e08 (ARM: EXYNOS: Fix low level debug support)
map_io() is not needed for exynos5440 so need to fix to lookup
cpu which using map_io(). Without this, kernel boot log complains
'CPU EXYNOS5440 support not enabled' on exynos5440 and panic().
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Adding maintainer for arch/arm/mach-keystone/
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Srinidhi's mail address is now bouncing and he has requested
me to delete this entry.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This was missed when splitting out the phy from the controller node in
commit 9dffe3be3f32 (ARM: tegra: modify ULPI reset GPIO properties).
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch removes sti_secondary_start from _INIT section, there are 2
reason for this removal.
1. discarding such a small code does not save much, given the RAM
sizes.
2. Having this code discarded, creates corruption issue when we boot
smp-kernel with nrcpus=1 or with single cpu node in DT.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch fixes cpu nodes with device_type = "cpu". This change was not
necessary before 3.10-rc7.
Without this patch STi SOCs does not boot as SMP.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second round of Renesas ARM based SoC fixes for v3.11
* Lager board: do not annotate gpio_buttons as __initdata
- This avoids accessing uninitialised memory if keys are pressed
after kernel initialisation completes.
- Bug introduced in gpio-keys were enabled in v3.11-rc1
* Bock-W board: fix SDHI0 PFC settings
- Allow detection of SD card
- Bug introduced in SDHI support was added in v3.11-rc1
* shdma: fixup sh_dmae_get_partial() calculation error
- Bug introduced in 2.6.34-rc1.
* armadillo800eva board: Don't request GPIO 166 in board code
- Allow use of touchscreen
- Bug introduced in v3.11-rc1
* tag 'renesas-fixes2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When the gpio-keys device is registered using
platform_device_register_data() the platform data argument,
lager_keys_pdata is duplicated and thus should be marked as __initdata
to avoid wasting memory. However, this is not true of gpio_buttons,
a reference to it rather than its value is duplicated when lager_keys_pdata
is duplicated.
This avoids accessing freed memory if gpio-key events occur
after unused kernel memory is freed late in the kernel's boot.
This but was added when support for gpio-keys was added to lager
in c3842e4fcbb7664276443b79187b7808c2e80a35
("ARM: shmobile: lager: support GPIO switches") which was included
in v3.11-rc1.
Tested-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The following message is printed on the BOCK-W kernel bootup:
sh-pfc pfc-r8a7778: invalid group "sdhi0" for function "sdhi0"
In addition, SD card cannot be detected. The reason is apparently that commit
ca7bb309485e4ec89a9addd47bea (ARM: shmobile: bockw: add SDHI0 support) matched
the previous version of commit 564617d2f92473031d035deb273da5 (sh-pfc: r8a7778:
add SDHI support).
Add the missing pin groups according to the BOCK-W board schematics.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
sh_desc->hw.tcr is controlling real data size,
and, register TCR is controlling data transfer count
which was xmit_shifted value of hw.tcr.
Current sh_dmae_get_partial() is calculating in different unit.
This patch fixes it.
This bug has been present since c014906a870ce70e009def0c9d170ccabeb0be63
("dmaengine: shdma: extend .device_terminate_all() to record partial
transfer"), which was added in 2.6.34-rc1.
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
89ae7b5bbd3e65bc6ab7a577ca5ec18569589c8c
(ARM: shmobile: armadillo800eva: Register pinctrl mapping for INTC)
mistakenly requests GPIO 166 in board code,
most probably due to a wrong merge conflict resolution.
As the GPIO is passed to the st1232 driver through platform
data and requested by the driver,
there's no need to request it in board code. Fix it.
Tested by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley via Tony Lindgren:
Some OMAP hwmod fixes for v3.11-rc. Mostly intended to fix an earlyprintk
regression and an AM33xx cpgmac power management regression.
Basic build, boot, and PM tests are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_a_v3.11-rc/20130730042132/
The tests include temporary fixes for the unrelated 2430SDP and OMAP3
boot regressions, which are not part of this signed tag.
* tag 'for-v3.11-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
ARM: OMAP2+: hwmod: rt address space index for DT
ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
ARM: OMAP2+: Avoid idling memory controllers with no drivers
ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Register target address to be used for cpgmac is the second device
address space. By default, hwmod picks first address space (0th index)
for register target.
With removal of address space from hwmod and using DT instead, cpgmac
is getting wrong address space for register target.
Fix it by indicating the address space to be used for register target.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Address space is being removed from hwmod database and DT information
in <reg> property is being used. Currently the 0th index of device
address space is used to map for register target address. This is not
always true, eg. cpgmac has it's sysconfig in second address space.
Handle it by specifying index of device address space to be used for
register target. As default value of this field would be zero with
static initialization, existing behaviour of using first address space
for register target while using DT would be kept as such.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
[paul@pwsan.com: use u8 rather than int to save memory]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Some hwmods which are marked with HWMOD_INIT_NO_IDLE are left in enabled
state post setup(). When a omap_device gets created for such hwmods
make sure the omap_device and pm_runtime states are also in sync for such
hwmods by doing a omap_device_enable() and pm_runtime_set_active() for the
device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Memory controllers in OMAP (like GPMC and EMIF) have the hwmods marked with
HWMOD_INIT_NO_IDLE and are left in enabled state post initial setup.
Even if they have drivers missing, avoid idling them as part of
omap_device_late_idle()
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With commit '82702ea11ddfe0e43382e1fa5b66d807d8114916' "ARM: OMAP2+:
Fix serial init for device tree based booting" stubbing out
omap_serial_early_init() for Device tree based booting, there was a
crash observed on AM335x based devices when hwmod does a
_setup_reset() early at boot.
This was rootcaused to hwmod trying to reset console uart while
earlycon was using it. The way to tell hwmod not to do this is to
specify the HWMOD_INIT_NO_RESET flag, which were infact set by the
omap_serial_early_init() function by parsing the cmdline to identify
the console device.
Parsing the cmdline to identify the uart used by earlycon itself seems
broken as there is nothing preventing earlycon to use a different one.
This patch, instead, attempts to populate the requiste flags for hwmod
based on the CONFIG_DEBUG_OMAPxUARTy FLAGS. This gets rid of the need
for cmdline parsing in the DT as well as non-DT cases to identify the
uart used by earlycon.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reported-by: Mark Jackson <mpfj-list@newflow.co.uk>
Reported-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Mark Jackson <mpfj-list@newflow.co.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fixes for omap5-uevm regulators from Nishanth Menon <nm@ti.com>:
Due to wrong older revision of documentation used as reference, we
seem to have a bunch of LDOs wrongly configured on OMAP5 uEVM. This
series is based power tree on production board 750-2628-XXX platform.
Unfortunately, the wrong voltages may be detrimental to OMAP5 as they
supply hardware blocks at voltages that are out of specification.
There is a chance that without these fixes there can be hardware
damage to omap5-uevm boards with the v3.11-rc series.
* tag 'omap-for-v3.11/fixes-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5-uevm: update optional/unused regulator configurations
ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
ARM: dts: omap5-uevm: document regulator signals used on the actual board
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.
The following optional/unused regulators can be updated:
- SMPS9 supplies TWL6040 over VDDA_2v1_AUD. This regulator needs to be
enabled only when audio is active. Since it does not come active by
default, it does not require "always-on" or "boot-on".
- LDO2 and LDO8 do not go to any peripheral or connector on the board.
Further, these unused regulators should have been 2.8V for LDO2 and
3.0V for LDO8. Mark these LDOs as disabled in the dts until needed.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.
The following fixes are hence mandatory to ensure right voltage is
supplied to key OMAP5 SoC voltage rails:
- LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This
can only be supplied at 1.5V or 1.8V and we currently supply 2.8V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is
a 'on need' supply to SoC IP and is not enabled by PMIC by
default at boot.
- LDO3 supplies Low Latency Interface(LLI) hardware module which is a
special hardware to communicate with Modem. However since uEVM is
not setup by default for this communication, this should be disabled
by default.
Further, vdda_lli is supposed to be 1.5V and not 3V.
- LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi
This can only be supplied at 1.5V or 1.8V and we currently
supply 2.2V.
To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.
Remove 'always-on' and 'boot-on' settings here as it is a 'on need'
supply to SoC IP and is not enabled by PMIC by default at boot.
- LDO6 supplies the board specified VDDS_1V2_WKUP supply going to
ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply
1.2V instead of 1.5V.
- LDO7 supplies VDD_VPP which is vpp1. This is currently configured for
1.5V which as per data manual "A pulse width of 1000 ns and an amplitude
of 2V is required to program each eFuse bit. Otherwise, VPP1 must not
be supplied".
So, fix the voltage to 2V. and disable the supply since we have no plans
of programming efuse bits - it can only be done once - in factory.
Further it is not enabled by default by PMIC so, 'boot-on' must be
removed, and the 'always-on' needs to be removed to achieve pulsing
if efuse needs to be programmed.
- LDO9 supplies the board specified vdds_sdcard supply going within SoC
specification of 1.8V or 3.0V. Further the supply is controlled by
switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to
be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled
on need basis.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.
However, currently we use the Palmas regulator names which is used for
different purposes on uEVM. Document the same based on 750-2628-XXX
boards - which is meant to be supported by this dts.
Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\ \ \
| |_|/
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into fixes
From David Brown, fixes for MSM for 3.11:
Two small fixes for MSM.
The first fixes the a gpio controller register address. I didn't see
any acks from the devicetree maintainers, so I've copied them on this
pull request. The change itself is minor, and just to the register
address.
The second change removes the gpiomux V1 code from MSM. This was
breaking compilation for some of the targets.
* tag 'msm-3.11-fix1' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: msm: Consolidate gpiomux for older architectures
ARM: msm: dts: Fix the gpio register address for msm8960
Signed-off-by: Olof Johansson <olof@lixom.net>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Msm gpiomux can be used only for 7x30 and 8x50.
Prevent compilation and fix build issues on 7X00, 8X60 and 8960.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
| | |/
| |
| |
| |
| |
| |
| | |
Fix the the gpio reg address for the device tree entry.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
|
| | | |
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Driver fixes for AM33xx, SIRF and PFC pin controllers
- Fix a compile warning from the pinctrl single-register driver
- Fix a little nasty memory leak
* tag 'pinctrl-for-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: fix a memleak when freeing maps
pinctrl: pinctrl-single: fix compile warning when no CONFIG_PM
pinctrl: sh-pfc: fix SDHI0 VccQ regulator on sh73a0 with DT
arm/dts: sirf: fix the pingroup name mismatch between drivers and dts
pinctrl: sirf: add usp0_uart_nostreamctrl pin group for usp-uart without flowctrl
pinctrl: sirf: fix the pin number and mux bit for usp0
pinctrl: am33xx dt binding: correct include path
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We forgot to free the node itself when free:ing a map.
Reported-by: xulinuxkernel <xulinuxkernel@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This warning has been introduced by the commit
0f9bc4bcdf4f pinctrl: single: adopt pinctrl sleep mode management
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The PFC pinctrl driver on sh73a0 is also regiatering a VccQ regulator for
SDHI0. However, its consumers list only included the platform-data based
SDHI device name. When booted with DT SDHI0 couldn't enable VccQ and
therefore was unusable. Fix this by adding a consumer with DT-based name.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
in drivers/pinctrl/sirf, pingroup name is cko0 and cko1, but in dts, they
are cko0 and cko1_rst. this patch fixes the error in dts.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
flowctrl
this patch adds the lost pin group which supports to let USP0 to simulate
a UART without hardware flow control.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
we missed a pin and related mux bit for usp pin group, this
patch fixes it.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Using #include <include/...> is a bit odd. It happens to work because the DTC
flags include -Iarch/FOO/boot/dts as well as arch/FOO/boot/dts/include and
arch/FOO/boot/dts/include/dt-bindings is a symlink to include/dt-bindings.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Oleg is working on fixing a very tight race between opening a event
file and deleting that event at the same time (both must be done as
root).
I also found a bug while testing Oleg's patches which has to do with a
race with kprobes using the function tracer.
There's also a deadlock fix that was introduced with the previous
fixes"
* tag 'trace-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Remove locking trace_types_lock from tracing_reset_all_online_cpus()
ftrace: Add check for NULL regs if ops has SAVE_REGS set
tracing: Kill trace_cpu struct/members
tracing: Change tracing_fops/snapshot_fops to rely on tracing_get_cpu()
tracing: Change tracing_entries_fops to rely on tracing_get_cpu()
tracing: Change tracing_stats_fops to rely on tracing_get_cpu()
tracing: Change tracing_buffers_fops to rely on tracing_get_cpu()
tracing: Change tracing_pipe_fops() to rely on tracing_get_cpu()
tracing: Introduce trace_create_cpu_file() and tracing_get_cpu()
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Commit a82274151af "tracing: Protect ftrace_trace_arrays list in trace_events.c"
added taking the trace_types_lock mutex in trace_events.c as there were
several locations that needed it for protection. Unfortunately, it also
encapsulated a call to tracing_reset_all_online_cpus() which also takes
the trace_types_lock, causing a deadlock.
This happens when a module has tracepoints and has been traced. When the
module is removed, the trace events module notifier will grab the
trace_types_lock, do a bunch of clean ups, and also clears the buffer
by calling tracing_reset_all_online_cpus. This doesn't happen often
which explains why it wasn't caught right away.
Commit a82274151af was marked for stable, which means this must be
sent to stable too.
Link: http://lkml.kernel.org/r/51EEC646.7070306@broadcom.com
Reported-by: Arend van Spril <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Cc: Alexander Z Lam <azl@google.com>
Cc: Vaibhav Nagarnaik <vnagarnaik@google.com>
Cc: David Sharp <dhsharp@google.com>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
If a ftrace ops is registered with the SAVE_REGS flag set, and there's
already a ops registered to one of its functions but without the
SAVE_REGS flag, there's a small race window where the SAVE_REGS ops gets
added to the list of callbacks to call for that function before the
callback trampoline gets set to save the regs.
The problem is, the function is not currently saving regs, which opens
a small race window where the ops that is expecting regs to be passed
to it, wont. This can cause a crash if the callback were to reference
the regs, as the SAVE_REGS guarantees that regs will be set.
To fix this, we add a check in the loop case where it checks if the ops
has the SAVE_REGS flag set, and if so, it will ignore it if regs is
not set.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
After the previous changes trace_array_cpu->trace_cpu and
trace_array->trace_cpu becomes write-only. Remove these members
and kill "struct trace_cpu" as well.
As a side effect this also removes memset(per_cpu_memory, 0).
It was not needed, alloc_percpu() returns zero-filled memory.
Link: http://lkml.kernel.org/r/20130723152613.GA23741@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
tracing_open() and tracing_snapshot_open() are racy, the memory
inode->i_private points to can be already freed.
Convert these last users of "inode->i_private == trace_cpu" to
use "i_private = trace_array" and rely on tracing_get_cpu().
v2: incorporate the fix from Steven, tracing_release() must not
blindly dereference file->private_data unless we know that
the file was opened for reading.
Link: http://lkml.kernel.org/r/20130723152610.GA23737@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
tracing_open_generic_tc() is racy, the memory inode->i_private
points to can be already freed.
1. Change its last user, tracing_entries_fops, to use
tracing_*_generic_tr() instead.
2. Change debugfs_create_file("buffer_size_kb", data) callers
to pass "data = tr".
3. Change tracing_entries_read() and tracing_entries_write() to
use tracing_get_cpu().
4. Kill the no longer used tracing_open_generic_tc() and
tracing_release_generic_tc().
Link: http://lkml.kernel.org/r/20130723152606.GA23730@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
tracing_open_generic_tc() is racy, the memory inode->i_private
points to can be already freed.
1. Change one of its users, tracing_stats_fops, to use
tracing_*_generic_tr() instead.
2. Change trace_create_cpu_file("stats", data) to pass "data = tr".
3. Change tracing_stats_read() to use tracing_get_cpu().
Link: http://lkml.kernel.org/r/20130723152603.GA23727@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
tracing_buffers_open() is racy, the memory inode->i_private points
to can be already freed.
Change debugfs_create_file("trace_pipe_raw", data) caller to pass
"data = tr", tracing_buffers_open() can use tracing_get_cpu().
Change debugfs_create_file("snapshot_raw_fops", data) caller too,
this file uses tracing_buffers_open/release.
Link: http://lkml.kernel.org/r/20130723152600.GA23720@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
tracing_open_pipe() is racy, the memory inode->i_private points to
can be already freed.
Change debugfs_create_file("trace_pipe", data) callers to to pass
"data = tr", tracing_open_pipe() can use tracing_get_cpu().
Link: http://lkml.kernel.org/r/20130723152557.GA23717@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Every "file_operations" used by tracing_init_debugfs_percpu is buggy.
f_op->open/etc does:
1. struct trace_cpu *tc = inode->i_private;
struct trace_array *tr = tc->tr;
2. trace_array_get(tr) or fail;
3. do_something(tc);
But tc (and tr) can be already freed before trace_array_get() is called.
And it doesn't matter whether this file is per-cpu or it was created by
init_tracer_debugfs(), free_percpu() or kfree() are equally bad.
Note that even 1. is not safe, the freed memory can be unmapped. But even
if it was safe trace_array_get() can wrongly succeed if we also race with
the next new_instance_create() which can re-allocate the same tr, or tc
was overwritten and ->tr points to the valid tr. In this case 3. uses the
freed/reused memory.
Add the new trivial helper, trace_create_cpu_file() which simply calls
trace_create_file() and encodes "cpu" in "struct inode". Another helper,
tracing_get_cpu() will be used to read cpu_nr-or-RING_BUFFER_ALL_CPUS.
The patch abuses ->i_cdev to encode the number, it is never used unless
the file is S_ISCHR(). But we could use something else, say, i_bytes or
even ->d_fsdata. In any case this hack is hidden inside these 2 helpers,
it would be trivial to change them if needed.
This patch only changes tracing_init_debugfs_percpu() to use the new
trace_create_cpu_file(), the next patches will change file_operations.
Note: tracing_get_cpu(inode) is always safe but you can't trust the
result unless trace_array_get() was called, without trace_types_lock
which acts as a barrier it can wrongly return RING_BUFFER_ALL_CPUS.
Link: http://lkml.kernel.org/r/20130723152554.GA23710@redhat.com
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is five bug fixes, two of which fix long standing problems
causing crashes (sd and mvsas). The remaining three are hung (isci
race) or lost (qla2xxx, isci) devices"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] isci: fix breakage caused by >16byte CDB patch
[SCSI] mvsas: Fix kernel panic on tile due to unaligned data access
[SCSI] sd: fix crash when UA received on DIF enabled device
[SCSI] qla2xxx: Properly set the tagging for commands.
[SCSI] isci: Fix a race condition in the SSP task management path
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Oops, apparently no-one I cc'd at intel actually bothered to check this
patch for the isci driver:
commit e73823f7a2c921dcf068d34ea03bd682498d9e42
Author: James Bottomley <JBottomley@Parallels.com>
Date: Tue May 7 15:38:18 2013 -0700
[SCSI] libsas: implement > 16 byte CDB support
sci_swab32_cpy needs multiples of four, so for commands that aren't that, it's
rounding the wrong way. fix by doing (len+3)/4 instead of len/4.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
