aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* ARM: at91: add pmc DT supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | Specified the main Oscillator via clock binding. This will allow to do not hardcode it anymore in the DT board at 12MHz. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: add specific DT soc initJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | | | | | | | This will allow to have static Device mapping and DT probe mapping for the System Controller. Temporary keep the call to ioremap_registers() until we have the binding for the SDRAM/DDR Controller. Temporary keep the main clock hardcoded to 12MHz until we have the binding for the PMC. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/dt: add Calao DAB-MMX daugther board support for USB-A9G20Jean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | | | | | | | | | | http://www.calao-systems.com/articles.php?lng=en&pg=6099 this daughter board add the following device: - Micro-SD socket - TTL 3V3 - (Tx/Rx/RTS/CTS) - I2C port - 0.96" Serial OLED Display Module (over UART) - MP3 decoder with Micro & Speakers - 4x PB, 4x Leds (Blue), 3x Leds (Green, Orange, Red) for now we add only the 2 UARTs, 4 Buttons, 7 leds and i2c via DT used_led1 will not be re-add via DT as it's used by the motherboard too Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: at91: sam9x5 add i2c DT supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | For now on use i2c-gpio driver on the same pin as the hardware IP. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Rob Herring <rob.herring@calxeda.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: sam9g45 add i2c DT supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | For now on use i2c-gpio driver on the same pin as the hardware IP. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Rob Herring <rob.herring@calxeda.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: usb_a9g20 add DT i2c supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | | | Use i2c-gpio and enable rv3029 RTC. Enable the rtc in the sam9g20 defconfig. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Rob Herring <rob.herring@calxeda.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: sam9g20 add i2c DT supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | For now on use i2c-gpio driver on the same pin as the hardware IP. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Rob Herring <rob.herring@calxeda.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
* i2c/gpio: add DT supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | | | | To achieve DT support, we need to populate a custom platform_data in a private struct from DT information. To simplify code, the adapter and algorithm are also put into the private struct. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: sam9x5 add nand supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | Enable the nand in the cpu module with the partition. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* atmel/nand: add DT supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | Use a local copy of board informatin and fill with DT data. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
* of/mtd/nand: add generic bindings and helpersJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | | | | - nand-ecc-mode : String, operation mode of the NAND ecc mode. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Stefan Roese <sr@denx.de>
* of: introduce helper to manage booleanJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | | | | of_property_read_bool Search for a property in a device node. Returns true if the property exist false otherwise. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Rob Herring <rob.herring@calxeda.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Grant Likely <grant.likely@secretlab.ca>
* ARM: at91: enable on flash bbt for Atmel Reference and DT boardsJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | Enable it on Calao board too as they are in DT too. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* mtd/atmel_nand: add on_flash_bbt to enable the use of On Flash BBTJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | This will allow to enable it from the board. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: David Woodhouse <dwmw2@infradead.org>
* ATMEL: fix nand ecc supportJean-Christophe PLAGNIOL-VILLARD2012-03-15
| | | | | | | | | | | | | | So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc and hardware). Set ecc mode in the boards to soft as currently in the driver. Move platform data to a common header include/linux/platform_data/atmel_nand.h Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no> Acked-by: David Woodhouse <dwmw2@infradead.org>
* ARM: at91: at91sam9x5cm/dt: add leds supportJean-Christophe PLAGNIOL-VILLARD2012-03-01
| | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: usb_a9g20/dt: add gpio-keys supportJean-Christophe PLAGNIOL-VILLARD2012-03-01
| | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: at91sam9m10g45ek/dt: add gpio-keys supportJean-Christophe PLAGNIOL-VILLARD2012-03-01
| | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: at91sam9m10g45ek/dt: add leds supportJean-Christophe PLAGNIOL-VILLARD2012-03-01
| | | | | | | Use the gpio for d7 as we do not support yet the pwm led via dt. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: usb_a9g20/dt: add leds supportJean-Christophe PLAGNIOL-VILLARD2012-03-01
| | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/pio: add new PIO3 featuresNicolas Ferre2012-03-01
| | | | | | | | | | | | | | | This patch adds the support for new PIO controller found on some at91sam SOCs. - more peripheral multiplexing - more features to configure on a PIO (pull-down, Schmitt trigger, debouncer) - support for several IRQ triggering features (type and polarity) Support for those new features are retrieved from the device tree compatibility string. Debugfs at91_gpio file is updated to monitor configuration. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: add sam9_smc.o to at91sam9x5 buildNicolas Ferre2012-03-01
| | | | | | | Add these SMC accessors to the at91sam9x5 as we will need them for NAND flash (for instance). Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/tc/clocksource: Add 32 bit variant to Timer CounterNicolas Ferre2012-03-01
| | | | | | | | | | | | | | | | Some SoC have a 32 bit variant of Timer Counter Blocks. We do not need the chaining of two 16 bit counters anymore for them. The SoC nature is deduced from the device tree "compatible" string. For non-device-tree configurations, backward compatibility is maintained by using the default 16 bit counter configuration. This patch addresses both the atmel_tclib and its user: tcb_clksrc clocksource. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
* ARM: at91/tc: add device tree support to atmel_tclibNicolas Ferre2012-03-01
| | | | | | | | | | | | | | Device tree support added to atmel_tclib: the generic Timer Counter library. This is used by the clocksource/clockevent driver tcb_clksrc. The current DT enabled platforms are also modified to use it: - .dtsi files are modified to add Timer Counter Block entries - alias are created to allow identification of each block - clkdev lookup tables are added for clocks identification. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
* ARM: at91/tclib: take iomem size from resourceNicolas Ferre2012-03-01
| | | | | | | | | | | Requesting iomem region and ioremaping is now done using the resource size specified instead of a constant value. Each <SoC>_device.c file is modified accordingly to reflect actual user interface size. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: at91/pit: add traces in case of errorNicolas Ferre2012-03-01
| | | | | | | Traces related to IRQ management are useful for timers in case of non-working IRQ subsystem (switch to irq_domain for instance). Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: pit add DT supportJean-Christophe PLAGNIOL-VILLARD2012-03-01
| | | | | | | | | | Retreive registers address and IRQ from device tree entry. Called from at91_dt_init_irq() so that timers are up-n-running when timers initialization will occur. Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> [nicolas.ferre@atmel.com: change error path and interrupts property handling] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91: AIC and GPIO IRQ device tree initializationNicolas Ferre2012-03-01
| | | | | | | | | | | | | | | | Both AIC and GPIO controllers are now using the standard of_irq_init() function to initialize IRQs in case of DT use. The DT specific initialization functions are now separated from the non-DT case and are now using "linear" irq domains. The .map() irqdomain operation is responsible for positioning the IRQ handlers. In AIC case, the Linux IRQ number is directly programmed in the hardware to avoid an additional reverse mapping operation. The AIC position its irq domain as the "default" irq domain. For DT case, the priority is not yet filled in the SMR. It will be the subject of another patch. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* ARM: at91/board-dt: remove AIC irq domain from board fileNicolas Ferre2012-03-01
| | | | | | | | Adding of irqdomain in AIC code make the specification of the irq domain in board file useless. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: at91/gpio: remove the static specification of gpio_chip.baseNicolas Ferre2012-03-01
| | | | | | | | This value is determined at runtime using device tree or platform data information. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: at91/gpio: add .to_irq gpio_chip handlerNicolas Ferre2012-03-01
| | | | | | | | | | Replace the gpio_to_irq() macro by a plain gpiolib .to_irq() handler. This call is using the irqdomain to translate hardware to Linux IRQ numbers. The irq_to_gpio() macro is completely removed. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node fieldNicolas Ferre2012-03-01
| | | | | | | | | | | | Protect build failure in case of non-DT configuration: the gpio_chip structure does not have a of_node field in case of !CONFIG_OF_GPIO. Keep this in a separate patch as it can be reverted if the field is added for both DT/non-DT cases. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: at91/gpio: add irqdomain and DT supportNicolas Ferre2012-03-01
| | | | | | | | | | Add "legacy" type of irqdomain to preserve old-style numbering and allow smooth transition for both DT and non-DT cases. Original idea and code by Jean-Christophe Plagniol-Villard. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM: at91/gpio: change comments and one variable nameNicolas Ferre2012-03-01
| | | | | | | | | | | What was true only on at91sam9263 about the sharing of a single AIC IRQ line for several GPIO banks is now used by several Atmel SoCs. Change a variable name to allow better understanding while introducing IRQ domains in following patches. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ARM/USB: at91/ohci-at91: remove the use of irq_to_gpioNicolas Ferre2012-03-01
| | | | | | | | | | | | irq_to_gpio() macro will be removed from AT91 GPIO interrupt controller. So we replace it with the use of gpio_to_irq() and a reworked test. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: linux-usb@vger.kernel.org
* ARM: at91/snapper9260: move gpio_to_irq out of structure initializationNicolas Ferre2012-03-01
| | | | | | | | | | gpio_to_irq() implementation will be moved from a macro to a plain function: we cannot use it in a structure initialization anymore. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Reviewed-by: Ryan Mallon <rmallon@gmail.com>
* ARM: at91/aic: add irq domain and device tree supportNicolas Ferre2012-03-01
| | | | | | | | | | | | | Add an irqdomain for the AIC interrupt controller. The device tree support is mapping the registers and is using the irq_domain_add_legacy() to manage hwirq translation. The documentation is describing the meaning of the two cells required for using this "interrupt-controller" in a device tree node. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Merge branch 'irqdomain/next' of git://git.secretlab.ca/git/linux-2.6Nicolas Ferre2012-03-01
|\
| * mfd: twl-core: Add IRQ_DOMAIN dependencyGrant Likely2012-02-26
| | | | | | | | | | | | | | | | | | | | | | TWL4030 depends on IRQ_DOMAIN support, so this patch selects it in Kconfig. It used to be that CONFIG_IRQ_DOMAIN must only be selected by the architecture, but recent cleanups have fixed it so that it is safe to select from anywhere. Signed-off-by: Benoit Cousson <b-cousson@ti.com> [grant.likely: Changed from a depends to a select] Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Samuel Ortiz <sameo@linux.intel.com>
| * devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)Grant Likely2012-02-26
| | | | | | | | | | | | | | | | | | | | | | | | Sparc has its own helpers for translating address ranges when the device tree is parsed at boot time, and it isn't able to use of_platform_populate(). However, there are some device drivers that want to use that function on other DT enabled platforms (ie. TWL4030). This patch adds an empty of_platform_populate() implementation that returns an error when CONFIG_OF_ADDRESS is not selected. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Samuel Ortiz <sameo@linux.intel.com>
| * irq_domain: Centralize definition of irq_dispose_mapping()Grant Likely2012-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several architectures define their own empty irq_dispose_mapping(). Since the irq_domain code is centralized now, there is little need to do so. This patch removes them and creates a new empty copy when !CONFIG_IRQ_DOMAIN is selected. The patch also means that IRQ_DOMAIN becomes selectable on all architectures. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Rob Herring <rob.herring@calxeda.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jonas Bonn <jonas@southpole.se> Cc: sparclinux@vger.kernel.org Cc: linux@lists.openrisc.net
| * irq_domain/mips: Allow irq_domain on MIPSGrant Likely2012-02-24
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch makes IRQ_DOMAIN usable on MIPS. It uses an ugly workaround to preserve current behaviour so that MIPS has time to add irq_domain registration to the irq controller drivers. The workaround will be removed in Linux v3.6 Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org
| * irq_domain/x86: Convert x86 (embedded) to use common irq_domainGrant Likely2012-02-23
| | | | | | | | | | | | | | | | | | | | This patch removes the x86-specific definition of irq_domain and replaces it with the common implementation. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Thomas Gleixner <tglx@linutronix.de>
| * ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.cPaul Gortmaker2012-02-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit bae1d8f19983fbfa25559aa3cb6a81a84aa82a18 (linux-next) "irq_domain/powerpc: Use common irq_domain structure instead of irq_host" made this change: -static struct irq_host *flipper_irq_host; +static struct irq_domain *flipper_irq_host; and this change: -static struct irq_host *hlwd_irq_host; +static struct irq_domain *hlwd_irq_host; The intent was to change the type, and not the name, but then in a couple of instances, it looks like the sed to change the irq_domain_ops name inadvertently also changed the irq_host name where it was not supposed to, causing build failures. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
| * irq_domain/microblaze: Convert microblaze to use irq_domainsGrant Likely2012-02-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch converts Microblaze to use the irq_domain remapper and get away from hard coding the offset between hwirq number and the linux irq number space. This also paves the way for multiple interrupt controllers. v2: Don't enable SPARSE_IRQ and keep NR_IRQS set to 33 Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Michal Simek <monstr@monstr.eu> Cc: Rob Herring <rob.herring@calxeda.com> Cc: John Williams <john.williams@petalogix.com> Cc: John Linn <john.linn@xilinx.com>
| * irq_domain/powerpc: Replace custom xlate functions with library functionsGrant Likely2012-02-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch converts a number of the powerpc drivers to use the common library of irq_domain xlate functions, dropping a bunch of lines in the process. v5: - Remove tsi108 changes from patch Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Milton Miller <miltonm@bga.com> Tested-by: Olof Johansson <olof@lixom.net>
| * irq_domain/powerpc: constify irq_domain_opsGrant Likely2012-02-16
| | | | | | | | | | | | | | | | | | | | Make all the irq_domain_ops structures in powerpc 'static const' Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Milton Miller <miltonm@bga.com> Tested-by: Olof Johansson <olof@lixom.net>
| * irq_domain/c6x: Use library of xlate functionsGrant Likely2012-02-16
| | | | | | | | | | | | | | | | | | The c6x irq controllers don't need to define custom .xlate hooks Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Mark Salter <msalter@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de>
| * irq_domain/c6x: constify irq_domain structuresGrant Likely2012-02-16
| | | | | | | | | | | | Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Mark Salter <msalter@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de>
| * irq_domain/c6x: Convert c6x to use generic irq_domain support.Mark Salter2012-02-16
| | | | | | | | | | | | | | | | | | | | | | | | The C6X IRQ support was copied almost verbatim from the PowerPC virtual IRQ code. The PowerPC code was used as the basis for generic irq_domain support, so this patch mostly copies what what done to arch/powerpc by Grant Likely in his irq_domain patch series. Signed-off-by: Mark Salter <msalter@redhat.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Cc: Aurelien Jacquiot <a-jacquiot@ti.com> Cc: Thomas Gleixner <tglx@linutronix.de>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-25 12:12:26 -0500