aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* netxen: clean up firmware version checksDhananjay Phadke2009-07-27
| | | | | | | | NX2031 firmware version will never be > 4.0.0, so replace (adapter->fw_major < 4) checks with pci revision ID check. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: Add default and limit macros for ring sizes.Dhananjay Phadke2009-07-27
| | | | | Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: refactor tso codeDhananjay Phadke2009-07-27
| | | | | | | | | o move all tso / checksum offload code into netxen_tso_check(). o optimize the tso header copy into simple loop. o clean up unnecessary unions from cmd_desc_type0 struct. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: annotate dma watchdog setupDhananjay Phadke2009-07-27
| | | | | | | | o remove superfluous code to setup PCI dma watchdog for NX2031. o disable dma watchdog completely for NX3031 (not required). Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: configure interrupt coalesce defaultsDhananjay Phadke2009-07-27
| | | | | | | | Initialize and configure interrupt coalesing defaults in the firmware, so that these also reflect in "ethool -c". Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: enable ip addr hashingDhananjay Phadke2009-07-27
| | | | | | | | | | | | | | NX3031 hardware requires local IP addresses for packet accumulation (LRO). IP address hashing is required to distinguish a local TCP flow from others (forwarded or guest). This patch adds listener for IP and netdev events and configures IP address in the firmware. Signed-off-by: Amit Kumar Salecha <amit@netxen.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: refresh firmware info after resetDhananjay Phadke2009-07-27
| | | | | | | | | | o move dma mask update to netxen_start_firmware() so that if firmware changes across suspend (e.g. file -> flash) it reflects right dma mask. o re-read firmware capabilities after firmware reset. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* mISDN: Fix wrong struct name in macro and clarificationsKarsten Keil2009-07-27
| | | | | | | | | | | | | Based on comments from Joe Perches <joe@perches.com>. Thanks. Fix IOFUNC_MEMIO macro. WriteFiFo##name##_MIO use the wrong struct name, this was missed because the macro was only called with this name. Clarify with _func that the defined types are functions. Add names to the parameters for better understanding the purpose. Signed-off-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fix multiple definitions of setup_w6692Stephen Rothwell2009-07-27
| | | | | | Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* phonet: phonet_device_get() fixEric Dumazet2009-07-27
| | | | | | | | | net/phonet/pn_dev.c: In function `phonet_device_get': net/phonet/pn_dev.c:99: warning: 'dev' might be used uninitialized in this function Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Update vlan_featuresEric Dumazet2009-07-26
| | | | | | | | | | | | | | [PATCH net-next-2.6] bnx2: Update vlan_features In order to get full use of some advanced features of BNX2, we now need to fill dev->vlan_features. Patch successfully tested with vlan devices built on top of bonding. (bond0 : one bnx2 slave, one tg3 slave (not yet vlan_features enabled) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* imwc3200: move iwmc3200 SDIO ids to sdio_ids.hTomas Winkler2009-07-26
| | | | | | | | 1. add intel's sdio vendor id to sdio_ids.h 2. move iwmc3200 sdio devices' ids to sdio_ids.h Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethtool: device independent rx_csum and get_flags routinesSridhar Samudrala2009-07-26
| | | | | | | | | | This helps avoid error messages with ethtool -k on devices that don't provide device specific routines. Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> ------------------------------------------------------------------ Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2x: Dont update vlan_features in bnx2x_set_tso()Eric Dumazet2009-07-26
| | | | | | | | | | Patrick said : "vlan_features doesn't need to be updated, the resulting dev->features of the VLAN device is computed as the intersection of dev->features and dev->vlan_features." Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: deprecate print_macJohannes Berg2009-07-26
| | | | | | | | | | | We've had %pM for long enough now, time to deprecate print_mac() and remove the __maybe_unused attribute from DECLARE_MAC_BUF so that variables declared with that can be found and removed. Otherwise people are putting in new users of print_mac(). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* sky2: remove unnecessary assignmentMike McCormack2009-07-26
| | | | | | Signed-off-by: Mike McCormack <mikem@ring3k.org> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phonet: Fix build.David S. Miller2009-07-26
| | | | | | | | | | | | As reported by Oliver Hartkopp: net/phonet/pn_dev.c: In function ‘phonet_init_net’: net/phonet/pn_dev.c:221: error: implicit declaration of function ‘proc_net_fops_create’ net/phonet/pn_dev.c: In function ‘phonet_exit_net’: net/phonet/pn_dev.c:242: error: implicit declaration of function ‘proc_net_remove’ Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-07-26
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
| * mac80211: Fix regression in mesh forwarding path.Javier Cardona2009-07-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The removal of the master netdev broke the mesh forwarding path. This patch fixes it by using the new internal 'pending' queue. As a result of this change, mesh forwarding no longer does the inefficient 802.11 -> 802.3 -> 802.11 conversion that was done before. [Changes since v1] Suggested by Johannes: - Select queue before adding to mpath queue - ieee80211_add_pending_skb -> ieee80211_add_pending_skbs - Remove unnecessary header wme.h Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: fix ieee80211_xmit call contextJohannes Berg2009-07-24
| | | | | | | | | | | | | | | | ieee80211_xmit() cannot be called with tasklets enabled because it is normally called from within a tasklet. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * net: remove unused skb->do_not_encryptJohannes Berg2009-07-24
| | | | | | | | | | | | | | | | mac80211 required this due to the master netdev, but now it can put all information into skb->cb and this can go. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: remove master netdevJohannes Berg2009-07-24
| | | | | | | | | | | | | | | | | | With the internal 'pending' queue system in place, we can simply put packets there instead of pushing them off to the master dev, getting rid of the master interface completely. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * net: export __dev_addr_sync/__dev_addr_unsyncJohannes Berg2009-07-24
| | | | | | | | | | | | | | | | | | | | For mac80211, with the master netdev removal, we need to be able to sync a multicast address list onto another list that is not tracked within a netdev, so we need access to the functions doing that. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * adm8211: remove uneeded code during suspend/resumeLuis R. Rodriguez2009-07-24
| | | | | | | | | | | | | | | | | | | | mac80211 drivers do not need to stop the software queues or call their own stop() callback upon suspend as we do it for drivers. Equally drivers don't have to call their own start() or start the queues as mac80211 will do it for us. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k: do not stop the queues in driver stopLuis R. Rodriguez2009-07-24
| | | | | | | | | | | | | | | | mac80211 will have disabled the queues for us when needed. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * MAINTAINERS: Update rtl8180 patternsJoe Perches2009-07-24
| | | | | | | | | | | | | | | | rtl8180 files were moved into a subdirectory by commit 1c740ed2210a0d124674a477ea538468aba47810 Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * MAINTAINERS: add wl1251 wireless driverKalle Valo2009-07-24
| | | | | | | | | | | | | | Add myself as the maintainer for wl1251 driver. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * wl1251: remove wl1251_plt_start/stop()Kalle Valo2009-07-24
| | | | | | | | | | | | | | | | This Production Line Testing code is currently unused and can be removed. It can be reintroduced when nl80211 test mode implemented for the driver. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * wl1251: remove accidentally added wl1251_netlink.cKalle Valo2009-07-24
| | | | | | | | | | | | | | | | Commit "wl1251: add wl1251 prefix to all 1251 files" accidentally added wl1251_netlink.c which contains a private netlink interface. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath5k: fix values for bus error bits in ISR2Pavel Roskin2009-07-24
| | | | | | | | | | | | | | | | | | The new values are taken from the recently open sourced Atheros HAL. Correctness is also confirmed by the users with access to Atheros documentation. Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * cfg80211: avoid setting default_key if add_key failsZhu Yi2009-07-24
| | | | | | | | | | | | | | | | | | | | | | In cfg80211_upload_connect_keys(), we call add_key, set_default_key and set_default_mgmt_key (if applicable) one by one. If one of these operations fails, we should stop calling the following functions. Because if the key is not added successfully, we should not set it as default key anyway. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwmc3200wifi: fix a use-after-free bugZhu Yi2009-07-24
| | | | | | | | | | | | | | | | The patch fixes a use-after-free bug for cmd->seq_num; Reported-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwmc3200wifi: fix cfg80211_connect_result is called in IBSSZhu Yi2009-07-24
| | | | | | | | | | | | | | Avoid calling cfg80211_connect_result() in IBSS mode. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwmc3200wifi: use cfg80211_connect_result to send req/resp IEZhu Yi2009-07-24
| | | | | | | | | | | | | | | | | | cfg80211_connect_result() let us specify associate request and response IEs as parameters after we are connected. We use this capability instead of doing it ourselves with WEXT. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * cfg80211: fix typo of IWEVASSOCRESPIEZhu Yi2009-07-24
| | | | | | | | | | | | | | It should be IWEVASSOCREQIE instead. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * cfg80211: set_default_key only for WEPZhu Yi2009-07-24
| | | | | | | | | | | | | | | | | | We invoke the cfg80211 set_default_key callback only for WEP key configuring. Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * p54: Eliminate unnecessary initializationLarry Finger2009-07-24
| | | | | | | | | | | | | | In two places, variables are unnecessilarly initialized to NULL. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: fix spare warnings in driver-trace.hChristian Lamparter2009-07-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following errors: driver-trace.h:148:1: error: cannot size expression driver-trace.h:148:1: error: cannot size expression [...] driver-trace.h:222:1: error: cannot size expression driver-trace.h:71:1: error: incompatible types for operation (<) driver-trace.h:71:1: left side has type void *<noident> driver-trace.h:71:1: right side has type int driver-trace.h:99:1: error: incompatible types for operation (<) driver-trace.h:99:1: left side has type void *<noident> driver-trace.h:99:1: right side has type int driver-trace.h:148:1: error: incompatible types for operation (<) driver-trace.h:148:1: left side has type void *<noident> driver-trace.h:148:1: right side has type int driver-trace.h:222:1: error: cannot size expression driver-trace.h:248:1: error: incompatible types for operation (<) driver-trace.h:248:1: left side has type void *<noident> driver-trace.h:248:1: right side has type int driver-trace.h:446:1: error: incompatible types for operation (<) driver-trace.h:446:1: left side has type void *<noident> driver-trace.h:446:1: right side has type int Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: do not monitor the connection while scanningChristian Lamparter2009-07-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mac80211 constantly monitors the connection to the associated AP in order to check if it is out of reach/dead. This is absolutely fine most of the time. Except when there is a scheduled scan for the whole neighborhood. After all this path could trigger while scanning on different channel. Or even worse: this AP probing triggers a WARN_ON in rate_lowest_index when the scan code did a band transition! ( http://www.kerneloops.org/raw.php?rawid=449304 ) Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Christian Lamparter <chunkeey@web.de> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * arlan: inverted logic?Roel Kluin2009-07-24
| | | | | | | | | | | | | | Inverted logic Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k: make use ath9k_hw_wait int ath9k_hw_reset_tsfGabor Juhos2009-07-24
| | | | | | | | | | | | | | | | | | We have a dedicated function for this kind of checks, use that instead of duplicating the code. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k: wake up the chip for TSF resetGabor Juhos2009-07-24
| | | | | | | | | | | | | | | | | | | | If we are in NETWORK SLEEP state, AR_SLP32_TSF_WRITE_STATUS limit always exceeds in 'ath9k_hw_reset_tsf', because reading of the AR_SLP3 register always return with the magic 0xdeadbeef value. Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * wl12xx: fix spellingStefan Weil2009-07-24
| | | | | | | | | | | | | | | | | | | | | | Changes (comments and debug output): * couldnt -> couldn't * frmware -> firmware * recevied -> received Signed-off-by: Stefan Weil <weil@mail.berlios.de> Acked-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rt2x00: Comment spellcheckingLuis Correia2009-07-24
| | | | | | | | | | | | | | | | Fix a bunch of spelling errors in the rt2x00 drivers Signed-off-by: Luis Correia <luis.f.correia@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: change iwl_enable/disable_interrupts to "inline"Wey-Yi Guy2009-07-24
| | | | | | | | | | | | | | | | | | iwl_enable_interrupts is being called inside the interrupt, change from function call to inline Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: inform user about rfkill state changesReinette Chatre2009-07-24
| | | | | | | | | | | | | | | | | | | | | | rfkill state changes are mostly available through debug messages. These are significant enough to always make user aware of so we turn them into warnings. Also insert a missing newline in some rfkill related debug message. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: clarify hardware error messageReinette Chatre2009-07-24
| | | | | | | | | | | | | | | | | | When a hardware error is detected we need to be clear about that and not create impression that the microcode is able to deal with it. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: make debug level more user friendlyReinette Chatre2009-07-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Deprecate the "debug50" module parameter used to obtain 5000 series and up debugging. Replace it with "debug" module parameter to match with original driver and be consistent between them. The "debug50" module parameter can still be used, except that the module parameter is not writable in keeping with its previous state. We currently just mark it as "deprecated" and do not have it in the feature-removal-schedule. Some more cleanup of module parameters needs to be done and can then be entered together. * Only make "debug" module parameters visible if the driver is compiled with CONFIG_IWLWIFI_DEBUG. This will eliminate a lot of confusion where users think they have set debug flags but yet cannot see any debug output. * Make module parameters writable. This eliminates the need for the "debug_level" sysfs file, which can now also be deprecated and added to feature-removal-schedule. This file is in significant use though with many iwlwifi documents and text referring users to it. We can thus not take its removal lightly and keep it around. With iwlcore shared between iwlagn and iwl3945 we really do not need debug module parameters for each but can instead have one debug module parameter for the iwlcore module. The same issue is here as with the sysfs file - a lot of iwlwifi documentation and text (like bug reports) rely on iwlagn and iwl3945 having this module parameter, so changing this to a module parameter of iwlcore will have significant impact and we do not do this for that reason. One consequence of this patch is that if a user is running a system with both 3945 and later hardware then the setting of the one module parameter will affect the value of the other. The likelihood of this seems low - and even if this setup is present it does not seem like an issue for both modules to run with the same debug level. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: uCode Alive notification with timeoutWey-Yi Guy2009-07-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wait for REPLY_ALIVE notification from init and runtime uCode. based on the type of REPLY_ALIVE, different status bit will be set to wake up the queue: STATUS_INIT_UCODE_ALIVE for init uCode STATUS_RT_UCODE_ALIVE for runtime uCode. If timeout, attempt to download the failing uCode image again. This can only be done for the init ucode images of all iwlagn devices and the runtime ucode image of the 5000 series and up. If there is a problem with the 4965 runtime ucode coming up we restart the interface and thus trigger a new download of the init ucode also. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: update 1000 series API version to match firmwareJay Sternberg2009-07-24
| | | | | | | | | | | | | | | | firmware file now contains build number so API needs to be updated. Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-10-17 02:33:28 -0400