aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* input: add driver for tnetv107x touchscreen controllerCyril Chemparathy2010-09-24
| | | | | | | | This patch adds support for tnetv107x's on-chip touchscreen controller. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: add keypad config for tnetv107x evm boardCyril Chemparathy2010-09-24
| | | | | | | | This patch adds evm board specific keymap definitions and controller configuration data for on-chip keypad controller on tnetv107x silicon. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: add tnetv107x keypad platform deviceCyril Chemparathy2010-09-24
| | | | | | | | This patch adds a platform device definition for tnetv107x's keypad controller. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* input: add driver for tnetv107x on-chip keypad controllerCyril Chemparathy2010-09-24
| | | | | | | | This patch adds support for tnetv107x's on-chip keypad controller. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* net: davinci_emac: cleanup unused cpdma codeCyril Chemparathy2010-09-24
| | | | | | | | | | | | Having switched over to the newly introduced cpdma layer, this patch now removes a whole bunch of code that is now unused. This patch has been maintained separate strictly for reasons of readability. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: David S. Miller <davem@davemloft.net> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* net: davinci_emac: switch to new cpdma layerCyril Chemparathy2010-09-24
| | | | | | | | | | | | | | | | | | | | | | | This patch hooks up the emac driver with the newly separated cpdma driver. Key differences introduced here: - The old buffer list scheme is no longer required - The original code maintained mac address per rx channel, even if only one rx channel was being used. With this change, mac address is maintained device wide. If support for multiple rx channels is added in future, this will need to be reworked a bit. - The new CPDMA code handles short packets better than before. The earlier code was adjusting the length up, without ensuring that the tail end of the padding was cleared - a possible security issue. This has been fixed to use skb_padto(). Signed-off-by: Cyril Chemparathy <cyril@ti.com> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* net: davinci_emac: separate out cpdma codeCyril Chemparathy2010-09-24
| | | | | | | | | | | | | | | In addition to being embedded into the EMAC controller, the CPDMA hardware block is used in TI's CPSW switch controller. Fortunately, the programming interface to this hardware block remains pretty nicely consistent across these devices. This patch adds a new CPDMA services layer, which can then be reused across EMAC and CPSW drivers. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* net: davinci_emac: cleanup unused mdio emac codeCyril Chemparathy2010-09-24
| | | | | | | | | | | This patch removes code that has been rendered useless by the previous patches in this series. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: David S. Miller <davem@davemloft.net> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* omap: cleanup unused davinci mdio arch codeCyril Chemparathy2010-09-24
| | | | | | | | | | This patch removes davinci architecture code that has now been rendered useless by the previous patches in the MDIO separation series. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: cleanup mdio arch code and switch to phy_idCyril Chemparathy2010-09-24
| | | | | | | | | | | | | This patch removes davinci architecture code that has now been rendered useless by the previous patches in the MDIO separation series. In addition, the earlier phy_mask definitions have been replaced with corresponding phy_id definitions. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* net: davinci_emac: switch to new mdioCyril Chemparathy2010-09-24
| | | | | | | | | | | | | | | | | | This patch switches the emac implementation over to the newly separated MDIO driver. With this, the mdio bus frequency defaults to a safe 2.2MHz. Boards may optionally specify a bus frequency via platform data. The phy identification scheme has been modified to use a phy bus id instead of a mask. This largely serves to eliminate the "phy search" code in emac init. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: David S. Miller <davem@davemloft.net> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* omap: add mdio platform devicesCyril Chemparathy2010-09-24
| | | | | | | | | | | | | This patch adds mdio platform devices on SoCs that have the necessary hardware. Clock lookup entries (aliases) have also been added, so that the MDIO and EMAC drivers can independently enable/disable a shared underlying clock. Further, the EMAC MMR region has been split down into separate MDIO and EMAC regions. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: add mdio platform devicesCyril Chemparathy2010-09-24
| | | | | | | | | | | | | | This patch adds mdio platform devices on SoCs that have the necessary hardware. Clock lookup entries (aliases) have also been added, so that the MDIO and EMAC drivers can independently enable/disable a shared underlying clock. Further, the EMAC MMR region has been split down into separate MDIO and EMAC regions. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Acked-by: David S. Miller <davem@davemloft.net> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* net: davinci_emac: separate out davinci mdioCyril Chemparathy2010-09-24
| | | | | | | | | | | | | | Davinci's MDIO controller is present on other TI devices, without an accompanying EMAC. For example, on tnetv107x, the same MDIO module is used in conjunction with a 3-port switch hardware. By separating the MDIO controller code into its own platform driver, this patch allows common logic to be reused on such platforms. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Tested-by: Michael Williamson <michael.williamson@criticallink.com> Tested-by: Caglar Akyuz <caglarakyuz@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: Add I2C0 devices to MityDSP-L138/MityARM-1808 platformMichael Williamson2010-09-24
| | | | | | | | | | This patch adds the i2c0 bus and attached devices to the MityDSP-L138 and MityARM-1808 davinci SoM. Included is a TPS65023 voltage regulator needed for power management and a small 24c02 EPROM that contains factory configuration data. Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: add idcode for tnetv107x rev 1.1/1.2Cyril Chemparathy2010-09-24
| | | | | | | | This patch adds an entry into the idcode table for tnetv107x silicon revision 1.1 and 1.2 devices. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: Initial support for MityDSP-L138/MityARM-1808Michael Williamson2010-09-24
| | | | | | | | | | | | | This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system on Module (SOM) under the machine name "mityomapl138". These SOMs are based on the da850 davinci CPU architecture. Information on these SOMs may be found at http://www.mitydsp.com. Basic support for the console UART, NAND, and EMAC (MII interface) is included in this patch. Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: Add CONFIG_REGULATOR_DUMMY to DA8XX defconfig file.Michael Williamson2010-09-24
| | | | | | | | | In order to support reference DA8XX machines not providing a voltage regulator control for the core voltage, the REGULATOR_DUMMY option is required. Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: Add machine checks to DA8XX serial console init routinesMichael Williamson2010-09-24
| | | | | | | | | | This patch adds machine checks in the serial console init routines for the DA8XX EVM boards. This is needed because there are other DA8XX based machines that use a different UART/tty as the console and may be included in a common kernel build. Signed-off-by: Michael Williamson <michael.williamson@criticallink.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: dm6467t evm: setup NAND flash timingSekhar Nori2010-09-24
| | | | | | | | | | | | | | | Setup NAND flash timing on DM6467T EVM. Without the timing setup, the NAND flash on DM6467T RevC EVM reports a number of random bad blocks because of read errors. Also, with this, copying a 100M file on RevB EVM takes ~35 sec against 1 minute 30 seconds earlier. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: am18x/da850/omap-l138 evm: setup NAND flash timingSekhar Nori2010-09-24
| | | | | | | | | | | | | | | | | | Setup the NAND flash timings for DA850 EVM Before configuring the timing values, throughput calculation using dd command yielded 469 kB/s write and 966 kB/s read speed. After the timing configuration, the throughput was measured to be 2.4 MB/s write and 5 MB/s read. [Mukul Bhatnagar: actual calculation of timing values from the NAND datasheet] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Cc: Mukul Bhatnagar <mbhatnagar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: am17x/da830/omap-l137 evm: setup NAND flash timingSudhakar Rajashekhara2010-09-24
| | | | | | | | | | | | | | | | | | | Setup the NAND flash timings for DA830 EVM. Before configuring the timing values, throughput calculation using dd command yielded 477 kB/s write and 970 kB/s read speed. After the timing configuration, the throughput was measured to be 2.5 MB/s write and 5.1 MB/s read. [Mukul Bhatnagar: actual calculation of timing values from the NAND datasheet] Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Mukul Bhatnagar <mbhatnagar@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: dm644x evm: setup NAND flash timingSekhar Nori2010-09-24
| | | | | | | | | | | | | | | | | | The DM644x EVM nand flash timing was earlier being done as a special case in the NAND driver itself. With the NAND driver now capable of progamming the AEMIF interface using timing data passed from the platform, the timing values are being moved into their rightful place in the EVM specific board file. The values being programmed match what was being done earlier and thus do not represent any change in performance/functionality. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* nand: davinci: add support for timing configurationSekhar Nori2010-09-24
| | | | | | | | | | | | | | | | | | | | | This patch modifies the DaVinci NAND driver to use the new AEMIF timing setup API to configure the NAND access timings. Earlier, AEMIF configuration was being done as a special case for DM644x board, but now more boards emerge which have capability to boot for other media (SPI flash, NOR flash) and have the kernel access NAND flash. This means that kernel cannot always depend on the bootloader to setup the NAND. Also, on platforms such as da850/omap-l138, the aemif input frequency changes as cpu frequency changes; necessiating re-calculation of timimg values as part of cpufreq transtitions. This patch forms the basis for adding that support. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* davinci: add support for aemif timing configurationSekhar Nori2010-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support to configure the AEMIF interface with supplied timing values. Since this capability is useful both from NOR and NAND flashes, it is provided as a new interface and in a file of its own. AEMIF timing configuration is required in cases: 1) Where the AEMIF clock rate can change at runtime (a side affect of cpu frequency change). 2) Where U-Boot does not support NAND/NOR but supports other media like SPI Flash or MMC/SD and thus does not care about setting up the AEMIF timing for kernel to use. 3) Where U-Boot just hasn't configured the timing values and cannot be upgraded because the box is already in the field. Since there is now a header file for AEMIF interface, the common (non-NAND specific) defines for AEMIF registers have been moved from nand.h into the newly created aemif.h Signed-off-by: Sekhar Nori <nsekhar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: dm365 evm: use EDMAQ_3 as the audio DMA queueSekhar Nori2010-09-24
| | | | | | | | | | | | | | By default the audio driver uses EDMAQ_0 as the DMA queue, but on DM365 this queue is specially designed for video transfers with a large fifo size. Having both audio and video transfers on the same queue leads to noise on the audio side. This patch changes the audio queue number for DM365 to EDMAQ_3. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* DA850: Add MMCSD1 resources, platform device and convenience registration ↵Juha Kuikka2010-09-24
| | | | | | | | | function Add resources, platform device and convenience registration function for DA850's second MMC/SD controller (MMCSD1). Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* DA850: Split MMCSD clock into two to support both MMCSD peripheralsJuha Kuikka2010-09-24
| | | | | | | | Split mmcsd_clk into mmcsd0_clk and mmcsd1_clk and add davinci_mmc.1 in preparation for adding support for MMCSD1 peripheral in DA850. Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* DA850: Add LPSC id for MMCSD1 peripheralJuha Kuikka2010-09-24
| | | | | | | Add LPSC id for DA850's MMCSD1 peripheral. Signed-off-by: Juha Kuikka <juha.kuikka@elektrobit.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* arm: mach-davinci: check irq2ctlr() resultKulikov Vasiliy2010-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | If irq2ctlr() fails return IRQ_NONE. Also as it can fail make 'ctlr' signed. The semantic patch that finds this problem (many false-positive results): (http://coccinelle.lip6.fr/) // <smpl> @ r1 @ identifier f; @@ int f(...) { ... } @@ identifier r1.f; type T; unsigned T x; @@ *x = f(...) ... *x > 0 Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* DA850: move MII/RMII pin lists to the board fileSergei Shtylyov2010-09-24
| | | | | | | | | | | | The CPGMAC pin list in da850.c was incorrectly split into two MII/RMII mode specific pin lists, while what pin group is used is a function of how the board is wired. Copy the pin lists to board-da850-evm.c, renaming them accordingly, and merge the two lists in da850.c into one, da850_cpgmac_pins[], representing the CPGMAC module as a whole... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Tested-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* DA850: move NAND/NOR pin lists to the board fileSergei Shtylyov2010-09-24
| | | | | | | | | | | | | | | The NAND/NOR flash pin lists (da850_nand_pins/da850_nor_pins) are purely board specific and as such shouldn't be in da850.c -- copy them to board-da850-evm.c, renaming to da850_evm_nand_pins/da850_evm_nor_pins respectively, and merge the two lists in da850.c into one, representing the EMIF 2.5 module as a whole, just like we have it in da830.c... While at it, remove the '__init' modifier from da850_evm_setup_nor_nand() as this function is called from non '__init' code... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Tested-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* Davinci: tnetv107x: retain psc reg base after initCyril Chemparathy2010-09-24
| | | | | | | | | This is a bugfix for the original tnetv107x submission series. The psc_regs base array was being discarded post-init, and this was causing a crash during post-init clock enable/disable. Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: am18x/da850/omap-l138: keep async clock constant with cpufreqSekhar Nori2010-09-24
| | | | | | | | | Keep PLL0 SYSCLK3 at a constant rate of 100MHz. This enables the AEMIF timing to remain valid even as the PLL0 output is changed by cpufreq driver to save power. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: cpufreq: add support for keeping an additional clock constantSekhar Nori2010-09-24
| | | | | | | | | | | | | | | | On OMAP-L138 SoC, some of the sysclks need not be at a fixed ratio to CPU clock and can be kept at a relatively constant rate by adjusting the PLLDIVn ratio even as cpufreq goes ahead and changes the CPU clock. This feature can be used to keep the EMIFA (PLL0 SYSCLK3) clock at a constant rate so that the EMIF timings need not be re-programmed whenever the CPU frequency changes. This patch adds the required suppport to cpufreq driver. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: clock: add support for setting sysclk rateSekhar Nori2010-09-24
| | | | | | | | | | | | | | | Setting sysclk rate will be useful in cases where the sysclk is not at a fixed ratio to the PLL output but can asynchronously be changed. This support forms the basis of attempt to keep the AEMIF clock constant on OMAP-L138 even as PLL0 output changes as ARM clock is changed to save power. This patch has been tested on OMAP-L138. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: dm365: disable pulldowns for all MMC/SD1 pins.Sekhar Nori2010-09-24
| | | | | | | | | | | | | This patch disables internal pulldowns for all MMC/SD1 pins. Presently only MMCSD1_CMD pin's pull down is disabled, but with this some MMC/SD cards do not get detected on MMC/SD1 slot of the EVM. The problem was reproducible with SanDisk 4GB SDHC card. Reported-by: Stephane Bovagne <s-bovagne@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: am18x/da850/omap-l138: use 'NOM' voltage defined in datasheet as ↵Sekhar Nori2010-09-24
| | | | | | | | | | | | | | | | | | min voltage For each DA850 OPP, the normal ('NOM') voltage defined in the tecnical reference manual (TRM) is actually the minimum voltage the frequency is supported at. The minimum ('MIN') voltage defined in TRM is meant to take care of voltage fluctuations and the device should not be run at this voltage for extended periods of time. Fix the OPP definitions to define the cvdd_min as the normal voltage defined in the datasheet. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: introduce support for AM1x ARM9 microprocessorsSekhar Nori2010-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | The Sitara AM17x SoCs from TI are an OMAP-L137 pin-to-pin compatible ARM9 microprocessor offering from TI. The Sitara AM18x SoCs from TI are an OMAP-L138 pin-to-pin compatible ARM9 microprocessor offering from TI. More information about these processors available at: www.ti.com/am1x Because of their compatibiliy with OMAP-L1x, the kernel support for OMAP-L1x is fully relevant to AM1x processors. This patch updates the Kconfig prompt and help text to include the AM1x part names to help users select configurations required for these parts easily. Also, the hardware information that shows up in /proc/cpuinfo is updated to show applicability of the respective OMAP-L1x EVMs for AM1x parts. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: clean up inconsistent usage of spaces in KconfigSekhar Nori2010-09-24
| | | | | | | | | | | | | In arch/arm/mach-davinci/Kconfig, some of the configuration items are indented with multiple spaces instead of tabs. Also, in couple of places, two spaces are used in the middle of help text where one should do. This patch fixes both issues. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: cpufreq: bailout on regulator errorsSekhar Nori2010-09-24
| | | | | | | | | | | | | | | | | | | | | | Current cpufreq code does not consider errors that can occur while changing voltage. Code to increase CPU frequency goes ahead even in the case the regulator has failed to increase the voltage. This leads to hard error since lower voltages cannot support increased frequency. Prevent this by not increasing frequency in case increasing voltage is not successful. Also, do not lower the voltage if changing the cpu frequency has failed for some reason. Note that we do not return error on failure to decrease voltage as that is not a hard error. Build fix for non-cpufreq kernels by Caglar Akyuz. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Cc: Caglar Akyuz <caglar@bilkon-kontrol.com.tr> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: clock: make 'disable unused clocks' printk debug onlyKevin Hilman2010-09-24
| | | | | | | The long list of clocks being disabled on boot is noisy and not needed for standard boots. Make this a debug printk instead. Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* MAINTAINERS: Add Kevin's e-mail in entry for TI DaVinciSekhar Nori2010-09-24
| | | | | | | | | | | In absence of Kevin's e-mail address, using get_maintaner.pl in git-send-email --cc-cmd option is not CCing Kevin at all. While at it, mark davinci-linux-open-source@linux.davincidsp.com as a list in line with what is being done for other maintainer entries. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* davinci: da850 evm: sparse cleanup: make file local variables staticSekhar Nori2010-09-24
| | | | | | | | | | | | | | | Without this cleanup, sparse checker reports warnings of the type: CHECK arch/arm/mach-davinci/board-da850-evm.c arch/arm/mach-davinci/board-da850-evm.c:112:22: warning: symbol 'da850_evm_nandflash_partition' was not declared. Should it be static? The nand flash partitions and regulator supplies are used within the EVM file and so should have been static This patch has been boot tested on DA830 and DA850 EVMs. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* Linux 2.6.36-rc5v2.6.36-rc5Linus Torvalds2010-09-20
|
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6Linus Torvalds2010-09-20
|\ | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: Staging: vt6655: fix buffer overflow Revert: "Staging: batman-adv: Adding netfilter-bridge hooks"
| * Staging: vt6655: fix buffer overflowDan Carpenter2010-09-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | "param->u.wpa_associate.wpa_ie_len" comes from the user. We should check it so that the copy_from_user() doesn't overflow the buffer. Also further down in the function, we assume that if "param->u.wpa_associate.wpa_ie_len" is set then "abyWPAIE[0]" is initialized. To make that work, I changed the test here to say that if "wpa_ie_len" is set then "wpa_ie" has to be a valid pointer or we return -EINVAL. Oddly, we only use the first element of the abyWPAIE[] array. So I suspect there may be some other issues in this function. Signed-off-by: Dan Carpenter <error27@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * Revert: "Staging: batman-adv: Adding netfilter-bridge hooks"Sven Eckelmann2010-09-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 96d592ed599434d2d5f339a1d282871bc6377d2c. The netfilter hook seems to be misused and may leak skbs in situations when NF_HOOK returns NF_STOLEN. It may not filter everything as expected. Also the ethernet bridge tables are not yet capable to understand batman-adv packet correctly. It was only added for testing purposes and can be removed again. Reported-by: Vasiliy Kulikov <segooon@gmail.com> Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds2010-09-20
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: USB: musb: MAINTAINERS: Fix my mail address USB: serial/mos*: prevent reading uninitialized stack memory USB: otg: twl4030: fix phy initialization(v1) USB: EHCI: Disable langwell/penwell LPM capability usb: musb_debugfs: don't use the struct file private_data field with seq_files
| * | USB: musb: MAINTAINERS: Fix my mail addressFelipe Balbi2010-09-20
| | | | | | | | | | | | | | | | | | | | | | | | | | | If we don't, contributors to musb and any USB OMAP code will be sending mails to an unexistent inbox. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
generated by cgit v1.2.2 (git 2.25.0) at 2024-11-20 10:55:33 -0500