| Commit message (Collapse) | Author | Age |
|---|
| |\ |
|
| | |\ |
|
| | | |
| | |
| | |
| | | |
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | | |
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This returns always false with new-style drivers right now. Make it
return always true instead, as a host must be present if we are able
to call the ioctl (without a host attached there would be no device
node to call on..)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
On Fri, Dec 13, 2002 at 12:24:39AM +1100, Anton Blanchard wrote:
> We tested 2.5.51 on a ppc64 box, qlogic 2312 and a fastt700 array. I
> had CONFIG_SCSI_REPORT_LUNS and unfortunately it thought the management
> LUN was a disk:
>
> Vendor: IBM Model: Universal Xport Rev: 0520
> Type: Direct-Access ANSI SCSI revision: 03
>
> ...
>
> SCSI device sdaj: drive cache: write through
> SCSI device sdaj: 40960 512-byte hdwr sectors (21 MB)
> sdaj: unknown partition table
> Attached scsi disk sdaj at scsi2, channel 0, id 0, lun 31
>
> ...
>
> end_request: I/O error, dev sdaj, sector 0
Three years later...
It looks like SGI use the same FC vendor and they already have a
workaround for this issue. The following patch adds the IBM version of
it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch adds a delay tailored for USB flash devices that are slow to
initialize their firmware. The symptom is a repeated Unit Attention with
ASC=0x28 (Not Ready to Ready transition). The patch will wait for up to 5
seconds for such devices to become ready. Normal devices won't send the
repeated Unit Attention sense key and hence won't trigger the patch.
This fixes a problem with James Roberts-Thomson's USB device, and I've
seen several reports of other devices exhibiting the same symptoms --
presumably they will be helped as well.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The problem lies in the way the error handler uses TEST UNIT READY to
tell whether error recovery has succeeded. The scsi_eh_tur function
gives up after one round of retrying; after that it decides that more
error recovery is needed.
However TUR is liable to report sense data indicating a retry is needed
when in fact error recovery has succeeded. A typical example might be
SK=2, ASC=4, ASCQ=1 (Logical unit in process of becoming ready). The mere
fact that we were able to get a sensible reply to the TUR should indicate
that the device is working well enough to stop error recovery.
I ran across a case back in January where this happened. A CD-ROM drive
timed out the INQUIRY command, and a device reset fixed the blockage.
But then the drive kept responding with 2/4/1 -- because it was spinning
up I suppose -- until the error handler gave up and placed it offline.
If the initial INQUIRY had received the 2/4/1 instead, everything would
have worked okay. It doesn't seem reasonable for things to fail just
because the error handler had started running.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The maximum size of a scatter-gather list that the current IBM VSCSI
Client can handle is 10. This patch adds large scatter-gather support
to the client so that it is capable of handling up to SG_ALL(255)
number of requests in the scatter-gather list.
Signed-off-by: Linda Xie <lxie@us.ibm.com>
Acked by: Dave C Boutcher <sleddog@us.ibm.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
On ISP24xx parts, stop execution of firmware during ISP
tear-down.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
From: Nishanth Aravamudan <nacc@us.ibm.com>
Replace schedule_timeout() with
msleep()/msleep_interruptible() as appropriate, to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
fc_remove_host() should only be called after a scsi_host has
been successfully added via scsi_add_host() -- any failures
while qla2xxx probing would result in an incorrect call to
fc_remove_host() during cleanup.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Export additional host information via the shost_attrs member in
the scsi_host template. Attributes include: driver version,
firmware version, ISP serial number, ISP type, ISP product ID,
HBA model name, HBA model description, PCI interconnect
information, and HBA port state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In a corner-case failure where the request-q does not
contain enough entries for a given request, pci_unmap_sg()
would be called twice. Remove direct call and let the
failure-path logic handle the unmapping.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove unnecessary RISC pause/release barriers during
ISP24xx flash manipulation. The ISP24xx can arbitrate flash
access requests during RISC executions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Original implementation used an overloaded bit in the EFI
parameters. The correct bit is BIT_4 of the special_options
section of NVRAM.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove redundant qla2x00_target_reset() function in favour of
the equivalent qla2x00_device_reset(). Update callers of
old function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In an FL topology, limit port recognition to those devices
not within the same area and domain of the ISP. The
firmware will recogonize such devices during local-loop
discovery.
Some devices may respond to a PLOGI before they have
completed their fabric login or they may not be a public
device. In this case they will report:
domain == 00
area == 00
alpa == <XX>
which is valid. Exclude such devices from local loop
discovery.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Export COS information for the fc_host and fc_remote_port
objects added by the driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In order to efficiently utilise the ISP's IOCB
request-queue, use the dma_get_required_mask() function to
determine the use of command-type 2 or 3 IOCBs when queueing
SCSI commands. This applies to ISP2[123]xx chips only, as
the ISP24xx uses command-type 7 IOCBs which use 64bit DSDs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | | |
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Assorted endianess fixes. I'll work on full endianess annotations
later.
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | | |
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | | |
Acked by: Moore, Eric Dean <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
#include of C files and macro tricks to rename symbols are evil and just
cause trouble. Let's doublicate the two functions as they're going to
go away soon enough anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This was noticed by Doug Bazamic and the fix found by Mark Salyzyn at
Adaptec.
There was an error in the BUG_ON() statement that validated the
calculated fib size which can cause the driver to panic.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch adopts the same solution as proposed by Kai M. in
a post titled: "[PATCH] SCSI tape signed/unsigned fix".
The fix is in a function that the sg driver borrowed from
the st driver so its maintenance is a little easier if
the functions remain the same after the fix.
- change nr_pages type from unsigned to signed so errors
from get_user_pages() call are properly handled
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
reported by Doug Gilbert and fixed by him in sg.c (see [PATCH] sg direct
io/mmap oops). Doug fixed the comparison in sg.c. This fix for st.c does not
touch the comparison but makes both arguments signed to remove the
problem. The new code is adapted from linux/fs/bio.c.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The idea behind a RAID class is to provide a uniform interface to all
RAID subsystems (both hardware and software) in the kernel.
To do that, I've made this class a transport class that's entirely
subsystem independent (although the matching routines have to match per
subsystem, as you'll see looking at the code). I put it in the scsi
subdirectory purely because I needed somewhere to play with it, but it's
not a scsi specific module.
I used a fusion raid card as the test bed for this; with that kind of
card, this is the type of class output you get:
jejb@titanic> ls -l /sys/class/raid_devices/20\:0\:0\:0/
total 0
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-0 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:0/20:1:0:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-1 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:1/20:1:1:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 device -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:0:0/20:0:0:0/
-r--r--r-- 1 root root 16384 Aug 16 17:21 level
-r--r--r-- 1 root root 16384 Aug 16 17:21 resync
-r--r--r-- 1 root root 16384 Aug 16 17:21 state
So it's really simple: for a SCSI device representing a hardware raid,
it shows the raid level, the array state, the resync % complete (if the
state is resyncing) and the underlying components of the RAID (these are
exposed in fusion on the virtual channel 1).
As you can see, this type of information can be exported by almost
anything, including software raid.
The more difficult trick, of course, is going to be getting it to
perform configuration type actions with writable attributes.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Since the attribute container deletes from a klist while it's walking
it, it is vulnerable to the problem (and fix) here:
http://marc.theaimsgroup.com/?l=linux-scsi&m=112485448830217
The attached fixes this (but won't compile without the above).
It also fixes the logical reversal in the traversal loop which meant
that we were never actually traversing the loop to hit this bug in the
first place.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
One of the changes in the attribute_container code in the scsi-misc tree
was to add a lock to protect the list of devices per container. This,
unfortunately, leads to potential scheduling while atomic problems if
there's a sleep in the function called by a trigger.
The correct solution is to use the kernel klist infrastructure instead
which allows lockless traversal of a list.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
scsi_io_completion() can be a bit noisy about certain conditions.
Previously this wasn't a problem for internally generated commands,
since they never hit it. However, since we do all SCSI commands via
bios, now they do. user CD testers like magicdev are now getting not
ready messages every time they touch the CD to see if there's anything
in it.
Fix this by making all scsi_execute commands REQ_QUIET and making
scsi_finish_io() not say anything for REQ_QUIET.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | |\| |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Here's the problem. Try to do this on 2.6.12:
- Kill udev and HAL
- Insert a CD-ROM into a SCSI or USB CD-ROM drive
- Run dd if=/dev/scd0
- cat /sys/block/sr0/size
- Eject the CD, insert a different one
- Run dd if=/dev/scd0
This is likely to do "access beyond the end of device", if you let it
- cat /sys/block/sr0/size
This shows the size of a previous CD, even though dd was supposed
to revalidate the device.
- Run dd if=/dev/scd0
The second run of dd works correctly!
The bug was introduced in 2.5.31, when Al fixes the recursive opens
in partitioning. Before, the code worked like this:
- Block layer called cdrom_open directly
- cdrom_open called sr_open
- sr_open called check_disk_change
- check_disk_change called sr_media_change
- sr_media_change did cd->needs_disk_change=1
- before returning sr_open tested cd->needs_disk_change
and called get_sector_size.
In 2.6.12, the check_disk_change is called from cdrom_open only. Thus:
- Block layer calls sr_bd_open
- sr_bd_open calls cdrom_open
- cdrom_open calls sr_open
- sr_open tests cd->needs_disk_change, which wasn't set yet; returns
- cdrom_open calls check_disk_change
- check_disk_change calls sr_media_change
- sr_media_change does cd->needs_disk_change=1, but nobody cares
Acked by: Alexander Viro <aviro@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The new bio code was incorrectly converted from stack allocated to
kmalloc'd buffer handling. There are two places where it incorrectly
uses sizeof(*sense) to get the size of the sense buffer. This
actually produces one, so no sense data was ever getting back, causing
failure in things like disk spin up.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The 3ware emulated commands all expect they are executing in the
use_sg == 0 case, which isn't true either in the block layer rework or
an SG_IO ioctl.
Fix this by adding the correct kmapping of the first element in the sg
list.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | | |
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Older gcc's require variable definitions at the beginning of a block.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
I also tinkered with it's sense recognition routines to make them take
scsi_sense_hdr structures instead of raw sense data.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This follows almost the identical model to sd, except that there's one
ioctl which returns raw sense data, so it had to use scsi_execute()
instead.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This one removes struct scsi_request entirely from sd. In the process,
I noticed we have no callers of scsi_wait_req who don't immediately
normalise the sense, so I updated the API to make it take a struct
scsi_sense_hdr instead of simply a big sense buffer.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This one's slightly more difficult. The transport class uses
REQ_FAILFAST, so another interface (scsi_execute) had to be invented to
take the extra flag. Also, the sense functions are shifted around to
allow spi_execute to place data directly into a struct scsi_sense_hdr.
With this change, there's probably a lot of unnecessary sense buffer
allocation going on which we can fix later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
After this, we just have some drivers, all the ULDs and the SPI
transport class using scsi_wait_req().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | |\| |
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This patch fixes a long term borkenness in
ibmvscsi where we were using the wrong timeout
field from the scsi command (and using the
wrong units.) Now broken by the fact that the
scsi_cmnd timeout field is gone entirely.
This only worked before because all the SCSI
targets assumed that 0 was default.
Signed-off-by: Dave Boutcher <boutcher@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
C files should include the files with the prototypes for their global
functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
attribute_container_classdev_to_container is an exported function of the
attribute_container.c file. However, there's no prototype for it. Now
I actually want to use it, so add one.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
