aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* [SERIAL] 8250: add tsi108 serial supportZang Roy-r619112006-07-09
| | | | | | | | | | | | | | | | | | | | | | | | | | The following patch gets rid of CONFIG_TSI108_BRIDGE. I add UPIO_TSI to handle IIR and IER register in serial_in and serial_out. (1) the reason to rewrite serial_in: TSI108 rev Z1 version ERRATA. Reading the UART's Interrupt Identification Register (IIR) clears the Transmit Holding Register Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they are not enabled in the Interrupt Enable Register (IER). This leads to loss of the interrupts. Interrupts are not cleared when reading UART registers as 32-bit word. (2) the reason to rewrite serial_out: Check for UART_IER_UUE bit in the autoconfig routine. This section of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are reserved for internal use. They are R/W bits. In addition to incorrect identification, changing these bits (from 00) will make Tsi108/109 UART non-functional. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* [SERIAL] IP22: fix serial console hangsJulien BLACHE2006-07-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch below fixes serial console hangs as seen on IP22 machines. Typically, while booting, the machine hangs for ~1 minute displaying "INIT: ", then the same thing happens again when init enters in the designated runlevel and finally the getty process on ttyS0 hangs indefinitely (though strace'ing it helps). strace (-e raw=ioctl, otherwise the ioctl() translation is utterly bogus) reveals that getty hangs on ioctl() 0x540f which happens to be TCSETSW (I saw it hang on another console ioctl() but couldn't reproduce that one). A diff between ip22zilog and sunzilog revealed the following differences: 1. the channel A flag being set on up.port.flags instead of up.flags 2. the channel A flag being set on what is marked as being channel B 3. sunzilog has a call to uart_update_timeout(port, termios->c_cflag, baud); at the end of sunzilog_set_termios(), which ip22zilog lacks (on purpose ?) The patch below addresses point 1 and fixes the serial console hangs just fine. However point 2 should be investigated by someone familiar with the IP22 Zilog; it's probably OK as is but even if it is, a comment in ip22zilog.c is badly needed. Point 3 is left as an exercise for whoever feels like digging into ip22zilog :) These are the main obvious differences between ip22zilog and sunzilog. Newer versions of sunzilog (Linus's git tree as of today) are more close to ip22zilog as the sbus_{write,read}b have been changed into simple {write,read}b, which shrinks the diff by a fair amount. Resyncing both drivers should be doable in a few hours time now for someone familiar with the IP22 Zilog hardware. Signed-off-by: Julien BLACHE <jb@jblache.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* [SERIAL] dz: Fix compilation errorMartin Michlmayr2006-07-09
| | | | | | | | | | | | | | Fix the following compilation error in the dz serial driver that got introduced with the "kernel console should send CRLF not LFCR" change. CC drivers/serial/dz.o drivers/serial/dz.c: In function 'dz_console_putchar': drivers/serial/dz.c:679: error: 'uport' undeclared (first use in this function) drivers/serial/dz.c:679: error: (Each undeclared identifier is reported only once drivers/serial/dz.c:679: error: for each function it appears in.) Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* i386: improve and correct inline asm memory constraintsLinus Torvalds2006-07-08
| | | | | | | | | | | | | Use "+m" rather than a combination of "=m" and "m" for improved clarity and consistency. This also fixes some inlines that incorrectly didn't tell the compiler that they read the old value at all, potentially causing the compiler to generate bogus code. It appear that all of those potential bugs were hidden by the use of extra "volatile" specifiers on the data structures in question, though. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* power: improve inline asm memory constraintsLinus Torvalds2006-07-08
| | | | | | | Use "+m" rather than a combination of "=m" and "m" for improved clarity and consistency. Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Fix cpufreq vs hotplug lockdep recursion.Dave Jones2006-07-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | [ There's some not quite baked bits in cpufreq-git right now so sending this on as a patch instead ] On Thu, 2006-07-06 at 07:58 -0700, Tom London wrote: > After installing .2356 I get this each time I boot: > ======================================================= > [ INFO: possible circular locking dependency detected ] > ------------------------------------------------------- > S06cpuspeed/1620 is trying to acquire lock: > (dbs_mutex){--..}, at: [<c060d6bb>] mutex_lock+0x21/0x24 > > but task is already holding lock: > (cpucontrol){--..}, at: [<c060d6bb>] mutex_lock+0x21/0x24 > > which lock already depends on the new lock. > make sure the cpu hotplug recursive mutex (yuck) is taken early in the cpufreq codepaths to avoid a AB-BA deadlock. Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Linux 2.6.18-rc1v2.6.18-rc1Linus Torvalds2006-07-06
| | | | It's all good.
* Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds2006-07-06
|\ | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [PKT_SCHED]: Fix error handling while dumping actions [PKT_SCHED]: Return ENOENT if action module is unavailable [PKT_SCHED]: Fix illegal memory dereferences when dumping actions
| * [PKT_SCHED]: Fix error handling while dumping actionsThomas Graf2006-07-05
| | | | | | | | | | | | | | | | | | | | | | "return -err" and blindly inheriting the error code in the netlink failure exception handler causes errors codes to be returned as positive value therefore making them being ignored by the caller. May lead to sending out incomplete netlink messages. Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * [PKT_SCHED]: Return ENOENT if action module is unavailableThomas Graf2006-07-05
| | | | | | | | | | Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * [PKT_SCHED]: Fix illegal memory dereferences when dumping actionsThomas Graf2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TCA_ACT_KIND attribute is used without checking its availability when dumping actions therefore leading to a value of 0x4 being dereferenced. The use of strcmp() in tc_lookup_action_n() isn't safe when fed with string from an attribute without enforcing proper NUL termination. Both bugs can be triggered with malformed netlink message and don't require any privileges. Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds2006-07-06
|\ \ | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SPARC64]: Fix stack overflow checking in modular non-SMP kernels. [SPARC64]: Fix sparc64 build errors when CONFIG_PCI=n.
| * | [SPARC64]: Fix stack overflow checking in modular non-SMP kernels.Mikael Pettersson2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sparc64 kernel's EXPORT_SYMBOL(_mcount) is inside an #ifdef CONFIG_SMP. This breaks modules in non-SMP kernels built with stack overflow checking (CONFIG_STACK_DEBUG=y), as modules_install reports: WARNING: /lib/modules/2.6.17/kernel/drivers/ide/ide-cd.ko needs unknown symbol _mcount Trivially fixed by moving EXPORT_SYMBOL(_mcount) outside of the #ifdef CONFIG_SMP. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
| * | [SPARC64]: Fix sparc64 build errors when CONFIG_PCI=n.Randy Dunlap2006-07-05
| |/ | | | | | | | | Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'upstream-linus' of ↵Linus Torvalds2006-07-05
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: [PCI] Add JMicron PCI ID constants [PATCH] ahci: Ensure that we don't grab both functions [PATCH] libata-core.c: restore configuration boot messages in ata_dev_configure(), v2 [PATCH] sata_sil24: add suspend/sleep support [PATCH] sata_sil24: separate out sil24_init_controller() [PATCH] sata_sil: add suspend/sleep support [PATCH] sata_sil: separate out sil_init_controller() [PATCH] libata: reimplement controller-wide PM [PATCH] libata: reimplement per-dev PM [PATCH] libata: implement PM EH actions [PATCH] libata: separate out __ata_ehi_hotplugged() [PATCH] libata: implement ATA_EHI_NO_AUTOPSY and QUIET [PATCH] libata: clean up debounce parameters and improve parameter selection [PATCH] libata: implement ATA_EHI_RESUME_LINK [PATCH] libata: replace ap_lock w/ ap->lock in ata_scsi_error() [PATCH] libata: fix ehc->i.action setting in ata_eh_autopsy() [PATCH] libata: add ap->pflags and move core dynamic flags to it [PATCH] libata: Conditionally set host->max_cmd_len [PATCH] sata_vsc: data_xfer should use mmio
| * | [PCI] Add JMicron PCI ID constantsJeff Garzik2006-07-05
| | | | | | | | | | | | | | | | | | They will be used in several IDE/libata files. Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] ahci: Ensure that we don't grab both functionsroot2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | When we force the chip into dual fn mode so we get PATA and AHCI we must be sure we don't then do anything dumb like try and grab both with the AHCI driver. Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata-core.c: restore configuration boot messages in ↵Borislav Petkov2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ata_dev_configure(), v2 This one looks better, IMHO. This restores the default libata configuration messages printed during booting. Signed-off-by: <petkov@math.uni-muenster.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] sata_sil24: add suspend/sleep supportTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | Add suspend/sleep support. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] sata_sil24: separate out sil24_init_controller()Tejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | Separate out controller initialization from sil24_init_one() into sil24_init_controller(). This will be used by resume. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] sata_sil: add suspend/sleep supportTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | Add suspend/sleep support. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] sata_sil: separate out sil_init_controller()Tejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | Separate out controller initialization from sil_init_one() into sil_init_controller(). This will be used by resume. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: reimplement controller-wide PMTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reimplement controller-wide PM. ata_host_set_suspend/resume() are defined to suspend and resume a host_set. While suspended, EHs for all ports in the host_set are pegged using ATA_FLAG_SUSPENDED and frozen. Because SCSI device hotplug is done asynchronously against the rest of libata EH and the same mutex is used when adding new device, suspend cannot wait for hotplug to complete. So, if SCSI device hotplug is in progress, suspend fails with -EBUSY. In most cases, host_set resume is followed by device resume. As each resume operation requires a reset, a single host_set-wide resume operation may result in multiple resets. To avoid this, resume waits upto 1 second giving PM to request resume for devices. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: reimplement per-dev PMTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reimplement per-dev PM. The original implementation directly put the device into suspended mode and didn't synchronize w/ EH operations including hotplug. This patch reimplements ata_scsi_device_suspend() and ata_scsi_device_resume() such that they request EH to perform the respective operations. Both functions synchronize with hotplug such that it doesn't operate on detached devices. Suspend waits for completion but resume just issues request and returns. This allows parallel wake up of devices and thus speeds up system resume. Due to sdev detach synchronization, it's not feasible to separate out EH requesting from sdev handling; thus, ata_device_suspend/resume() are removed and everything is implemented in the respective libata-scsi functions. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: implement PM EH actionsTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement two PM per-dev EH actions - ATA_EH_SUSPEND and ATA_EH_RESUME. Each action puts the target device into suspended mode and resumes from it respectively. Once a device is put to suspended mode, no EH operations other than RESUME is allowed on the device. The device will stay suspended till it gets resumed and thus reset and revalidated. To implement this, a new device state helper - ata_dev_ready() - is implemented and used in EH action implementations to make them operate only on attached & running devices. If all possible devices on a port are suspended, reset is skipped too. This prevents spurious events including hotplug events from disrupting suspended devices. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: separate out __ata_ehi_hotplugged()Tejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | Separate out __ata_ehi_hotplugged() from ata_ehi_hotplugged(). The underscored version doesn't set AC_ERR_ATA_BUS. This will be used for resume which is a hotplug event but not an ATA bus error. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: implement ATA_EHI_NO_AUTOPSY and QUIETTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement ATA_EHI_NO_AUTOPSY and QUIET. These used to be implied by ATA_PFLAG_LOADING, but new power management and PMP support need to use these separately. e.g. Suspend/resume operations shouldn't print full EH messages and resume shouldn't be recorded as an error. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: clean up debounce parameters and improve parameter selectionTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The names of predefined debounce timing parameters didn't exactly match their usages. Rename to more generic names and implement param selection helper sata_ehc_deb_timing() which uses EHI_HOTPLUGGED to select params. Combined with the previous EHI_RESUME_LINK differentiation, this makes parameter selection accurate. e.g. user scan resumes link but normal deb param is used instead of hotplug param. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: implement ATA_EHI_RESUME_LINKTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement ATA_EHI_RESUME_LINK, which indicates that the link needs to be resumed. This used to be implied by ATA_EHI_HOTPLUGGED. However, hotplug isn't the only event which requires link resume and separating this out allows other places to request link resume. This differentiation also allows better debounce timing selection. This patch converts user scan to use ATA_EHI_RESUME_LINK. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: replace ap_lock w/ ap->lock in ata_scsi_error()Tejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ap_lock was used because &ap->host_set->lock was too long and used a lot. Now that &ap->host_set->lock is replaced with ap->lock, there's no reason to keep ap_lock. [ed. note: that's not entirely true. ap_lock is a local variable, caching the results of a de-ref. In theory, if the compiler is smart enough, this patch is cosmetic. However, since this is not a fast path (it is the error path), this patch is nonetheless acceptable, even though it _may_ introduce a performance regression.] Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: fix ehc->i.action setting in ata_eh_autopsy()Tejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ata_eh_autopsy() used to directly assign determined action mask to ehc->i.action thus overriding actions set by some of nested analyze functions. This patch makes ata_eh_autopsy() add action masks just as it's done in other places. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: add ap->pflags and move core dynamic flags to itTejun Heo2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ap->flags is way too clamped. Separate out core dynamic flags to ap->pflags. ATA_FLAG_DISABLED is a dynamic flag but left alone as it's referenced by a lot of LLDs and it's gonna be removed once all LLDs are converted to new EH. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] libata: Conditionally set host->max_cmd_lenBrian King2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | In preparation for SAS attached SATA devices, which will not have a libata scsi_host, only setup host->max_cmd_len if ap->host exists. Signed-off-by: Brian King <brking@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [PATCH] sata_vsc: data_xfer should use mmioMartin Hicks2006-07-05
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hi, sata_vsc is an MMIO device, and should use the correct data_xfer function. This problem was introduced by: commit a6b2c5d4754dc539a560fdf0d3fb78a14174394a Author: Alan Cox <alan@lxorguk.ukuu.org.uk> Date: Mon May 22 16:59:59 2006 +0100 [PATCH] PATCH: libata. Add ->data_xfer method Signed-off-by: Martin Hicks <mort@bork.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | Merge git://git.linux-nfs.org/pub/linux/nfs-2.6Linus Torvalds2006-07-05
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.linux-nfs.org/pub/linux/nfs-2.6: NLM,NFSv4: Wait on local locks before we put RPC calls on the wire VFS: Add support for the FL_ACCESS flag to flock_lock_file() NFSv4: Ensure nfs4_lock_expired() caches delegated locks NLM,NFSv4: Don't put UNLOCK requests on the wire unless we hold a lock VFS: Allow caller to determine if BSD or posix locks were actually freed NFS: Optimise away an excessive GETATTR call when a file is symlinked This fixes a panic doing the first READDIR or READDIRPLUS call when: NFS: Fix NFS page_state usage Revert "Merge branch 'odirect'"
| * \ Merge branch 'locks'Trond Myklebust2006-07-05
| |\ \
| | * | NLM,NFSv4: Wait on local locks before we put RPC calls on the wireTrond Myklebust2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use FL_ACCESS flag to test and/or wait for local locks before we try requesting a lock from the server Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| | * | VFS: Add support for the FL_ACCESS flag to flock_lock_file()Trond Myklebust2006-07-05
| | | | | | | | | | | | | | | | Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| | * | NFSv4: Ensure nfs4_lock_expired() caches delegated locksTrond Myklebust2006-07-05
| | | | | | | | | | | | | | | | Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| | * | NLM,NFSv4: Don't put UNLOCK requests on the wire unless we hold a lockTrond Myklebust2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the new behaviour of {flock,posix}_file_lock(F_UNLCK) to determine if we held a lock, and only send the RPC request to the server if this was the case. Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| | * | VFS: Allow caller to determine if BSD or posix locks were actually freedTrond Myklebust2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change posix_lock_file_conf(), and flock_lock_file() so that if called with an F_UNLCK argument, and the FL_EXISTS flag they will indicate whether or not any locks were actually freed by returning 0 or -ENOENT. Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| * | | NFS: Optimise away an excessive GETATTR call when a file is symlinkedTrond Myklebust2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the case when compiling via a symlink tree, we want to ensure that the close-to-open GETATTR call is applied only to the final file, and not to the symlink. Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| * | | This fixes a panic doing the first READDIR or READDIRPLUS call when:Trond Myklebust2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * the client is ia64 or any platform that actually implements flush_dcache_page(), and * the server returns fsinfo.dtpref >= client's PAGE_SIZE, and * the server does *not* return post-op attributes for the directory in the READDIR reply. Problem diagnosed by Greg Banks <gnb@melbourne.sgi.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| * | | NFS: Fix NFS page_state usageTrond Myklebust2006-07-05
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | The introduction of the FLUSH_INVALIDATE argument to nfs_sync_inode_wait() does not clear the nr_unstable page state counter for pages that are being released. Also fix a longstanding similar bug when nfs_commit_list() fails. Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
| * | Merge branch 'master' of /home/trondmy/kernel/linux-2.6/Trond Myklebust2006-07-05
| |\ \
| * \ \ Merge branch 'master' of /home/trondmy/kernel/linux-2.6/Trond Myklebust2006-07-03
| |\ \ \
| * \ \ \ Merge branch 'master' of /home/trondmy/kernel/linux-2.6/Trond Myklebust2006-06-28
| |\ \ \ \
| * | | | | Revert "Merge branch 'odirect'"Trond Myklebust2006-06-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts ccf01ef7aa9c6c293a1c64c27331a2ce227916ec commit. No idea how git managed this one: when I asked it to merge the odirect topic branch it actually generated a patch which reverted the change. Reverting the 'merge' will once again reveal Chuck's recent NFS/O_DIRECT work to the world. Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* | | | | | Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds2006-07-05
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 3711/1: AT91 timer update [ARM] 3709/1: pnx4008: convert to generic irq subsystem [ARM] 3710/1: AT91 Serial: Use GPIO API
| * | | | | | [ARM] 3711/1: AT91 timer updateAndrew Victor2006-07-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Patch from Andrew Victor The AIC interrupt controller is the same on the Atmel AT91RM9200, AT91SAM9261 and AT91SAM9260 processors. This patch removes any RM9200-specific naming from the IRQ driver, and moves the AT91RM9200's default IRQ priority table into at91rm9200.c. Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
generated by cgit v1.2.2 (git 2.25.0) at 2025-01-02 18:22:54 -0500