aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* bridge: Add multicast count/interval sysfs entriesHerbert Xu2010-02-28
| | | | | | | | | This patch allows the user to the IGMP parameters related to the snooping function of the bridge. This includes various time values and retransmission limits. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add hash elasticity/max sysfs entriesHerbert Xu2010-02-28
| | | | | | | | | | | | | | | | This patch allows the user to control the hash elasticity/max parameters. The elasticity setting does not take effect until the next new multicast group is added. At which point it is checked and if after rehashing it still can't be satisfied then snooping will be disabled. The max setting on the other hand takes effect immediately. It must be a power of two and cannot be set to a value less than the current number of multicast group entries. This is the only way to shrink the multicast hash. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add multicast_snooping sysfs toggleHerbert Xu2010-02-28
| | | | | | | | | | | This patch allows the user to disable IGMP snooping completely through a sysfs toggle. It also allows the user to reenable snooping when it has been automatically disabled due to hash collisions. If the collisions have not been resolved however the system will refuse to reenable snooping. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add multicast_router sysfs entriesHerbert Xu2010-02-28
| | | | | | | | | | | | | | This patch allows the user to forcibly enable/disable ports as having multicast routers attached. A port with a multicast router will receive all multicast traffic. The value 0 disables it completely. The default is 1 which lets the system automatically detect the presence of routers (currently this is limited to picking up queries), and 2 means that the port will always receive all multicast traffic. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add multicast data-path hooksHerbert Xu2010-02-28
| | | | | | | | | This patch finally hooks up the multicast snooping module to the data path. In particular, all multicast packets passing through the bridge are fed into the module and switched by it. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add multicast start/stop hooksHerbert Xu2010-02-28
| | | | | | | | This patch hooks up the bridge start/stop and add/delete/disable port functions to the new multicast module. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add multicast forwarding functionsHerbert Xu2010-02-28
| | | | | | | | | | | | | This patch adds code to perform selective multicast forwarding. We forward multicast traffic to a set of ports plus all multicast router ports. In order to avoid duplications among these two sets of ports, we order all ports by the numeric value of their pointers. The two lists are then walked in lock-step to eliminate duplicates. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Add core IGMP snooping supportHerbert Xu2010-02-28
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the core functionality of IGMP snooping support without actually hooking it up. So this patch should be a no-op as far as the bridge's external behaviour is concerned. All the new code and data is controlled by the Kconfig option BRIDGE_IGMP_SNOOPING. A run-time toggle is also available. The multicast switching is done using an hash table that is lockless on the read-side through RCU. On the write-side the new multicast_lock is used for all operations. The hash table supports dynamic growth/rehashing. The hash table will be rehashed if any chain length exceeds a preset limit. If rehashing does not reduce the maximum chain length then snooping will be disabled. These features may be added in future (in no particular order): * IGMPv3 source support * Non-querier router detection * IPv6 Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Split may_deliver/deliver_clone out of br_floodHerbert Xu2010-02-28
| | | | | | | | | | | | This patch moves the main loop body in br_flood into the function may_deliver. The code that clones an skb and delivers it is moved into the deliver_clone function. This allows this to be reused by the future multicast forward function. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Use BR_INPUT_SKB_CB on xmit pathHerbert Xu2010-02-28
| | | | | | | | | this patch makes BR_INPUT_SKB_CB available on the xmit path so that we could avoid passing the br pointer around for the purpose of collecting device statistics. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Avoid unnecessary clone on forward pathHerbert Xu2010-02-28
| | | | | | | | | | | When the packet is delivered to the local bridge device we may end up cloning it unnecessarily if no bridge port can receive the packet in br_flood. This patch avoids this by moving the skb_clone into br_flood. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Allow tail-call on br_pass_frame_upHerbert Xu2010-02-28
| | | | | | | | | This patch allows tail-call on the call to br_pass_frame_up in br_handle_frame_finish. This is now possible because of the previous patch to call br_pass_frame_up last. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* bridge: Do br_pass_frame_up after other portsHerbert Xu2010-02-28
| | | | | | | | | | | | | | At the moment we deliver to the local bridge port via the function br_pass_frame_up before all other ports. There is no requirement for this. For the purpose of IGMP snooping, it would be more convenient if we did the local port last. Therefore this patch rearranges the bridge input processing so that the local bridge port gets to see the packet last (if at all). Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* tg3: Remove now useless VPD codeMatt Carlson2010-02-28
| | | | | | | | | Now that the VPD searching code is abstracted away, the outer loop used to detect the read-only large resource data type section is useless. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* bnx2: Remove now useless VPD codeMatt Carlson2010-02-28
| | | | | | | | | Now that the VPD searching code is abstracted away, the outer loop used to detect the read-only large resource data type section is useless. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* pci: Add helper to search for VPD keywordsMatt Carlson2010-02-28
| | | | | | | | | | | This patch adds the pci_vpd_find_info_keyword() helper function to find information field keywords within read-only and read-write large resource data type sections. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* pci: Add VPD information field helper functionsMatt Carlson2010-02-28
| | | | | | | | | | | This patch adds a preprocessor constant to describe the PCI VPD information field header size and an inline function to extract the size of the information field itself. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* pci: Add helper to find a VPD resource data typeMatt Carlson2010-02-28
| | | | | | | | | | This patch adds the pci_vpd_find_tag() helper function to find VPD resource data types in a buffer. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* pci: Add large and small resource data type codeMatt Carlson2010-02-28
| | | | | | | | | | | | This patch introduces more VPD preprocessor definitions to identify some small and large resource data type item names. The patch then continues to correct how the tg3 and bnx2 drivers search for the "read-only data" large resource data type. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* pci: Add PCI LRDT tag size and section sizeMatt Carlson2010-02-28
| | | | | | | | | | | This patch adds a preprocessor constant to describe the PCI VPD large resource data type tag size and an inline function to extract the large resource section size from the large resource data type tag. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: move TC_PRIO_CONTROL check into ixgbe_select_queue()John Fastabend2010-02-27
| | | | | | | | | | | | | | | | Move TC_PRIO_CONTROL check and queue remapping into ixgbe_select_queue(). Remapping queues after the qdisc can result in the wrong qdisc queue being stopped with netif_stop_subqueue(). Even if this is resolved and the correct queue is stopped it can result in a queue being blocked by TC_PRIO_CONTROL frames uneccesarily. Moving this into the select_queue routine maintains alignment between tx_rings and qdisc queues. Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* skbuff: align sk_buff::cb to 64 bit and close some potential holesFelix Fietkau2010-02-27
| | | | | | | | | | | | | | | | | | | The alignment requirement for 64-bit load/store instructions on ARM is implementation defined. Some CPUs (such as Marvell Feroceon) do not generate an exception, if such an instruction is executed with an address that is not 64 bit aligned. In such a case, the Feroceon corrupts adjacent memory, which showed up in my tests as a crash in the rx path of ath9k that only occured with CONFIG_XFRM set. This crash happened, because the first field of the mac80211 rx status info in the cb is an u64, and changing it corrupted the skb->sp field. This patch also closes some potential pre-existing holes in the sk_buff struct surrounding the cb[] area. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
* bonding: fix device leak on error in bond_create()Patrick McHardy2010-02-27
| | | | | | | | When the register_netdevice() call fails, the newly allocated device is not freed. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* rtnetlink: support specifying device flags on device creationPatrick McHardy2010-02-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit e8469ed959c373c2ff9e6f488aa5a14971aebe1f Author: Patrick McHardy <kaber@trash.net> Date: Tue Feb 23 20:41:30 2010 +0100 Support specifying the initial device flags when creating a device though rtnl_link. Devices allocated by rtnl_create_link() are marked as INITIALIZING in order to surpress netlink registration notifications. To complete setup, rtnl_configure_link() must be called, which performs the device flag changes and invokes the deferred notifiers if everything went well. Two examples: # add macvlan to eth0 # $ ip link add link eth0 up allmulticast on type macvlan [LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 26:f8:84:02:f9:2a brd ff:ff:ff:ff:ff:ff [ROUTE]ff00::/8 dev macvlan0 table local metric 256 mtu 1500 advmss 1440 hoplimit 0 [ROUTE]fe80::/64 dev macvlan0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 [LINK]11: macvlan0@eth0: <BROADCAST,MULTICAST,ALLMULTI,UP,LOWER_UP> mtu 1500 link/ether 26:f8:84:02:f9:2a [ADDR]11: macvlan0 inet6 fe80::24f8:84ff:fe02:f92a/64 scope link valid_lft forever preferred_lft forever [ROUTE]local fe80::24f8:84ff:fe02:f92a via :: dev lo table local proto none metric 0 mtu 16436 advmss 16376 hoplimit 0 [ROUTE]default via fe80::215:e9ff:fef0:10f8 dev macvlan0 proto kernel metric 1024 mtu 1500 advmss 1440 hoplimit 0 [NEIGH]fe80::215:e9ff:fef0:10f8 dev macvlan0 lladdr 00:15:e9:f0:10:f8 router STALE [ROUTE]2001:6f8:974::/64 dev macvlan0 proto kernel metric 256 expires 0sec mtu 1500 advmss 1440 hoplimit 0 [PREFIX]prefix 2001:6f8:974::/64 dev macvlan0 onlink autoconf valid 14400 preferred 131084 [ADDR]11: macvlan0 inet6 2001:6f8:974:0:24f8:84ff:fe02:f92a/64 scope global dynamic valid_lft 86399sec preferred_lft 14399sec # add VLAN to eth1, eth1 is down # $ ip link add link eth1 up type vlan id 1000 RTNETLINK answers: Network is down <no events> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* dev: support deferring device flag change notificationsPatrick McHardy2010-02-27
| | | | | | | | | | | | | | | | | | | | | | | Split dev_change_flags() into two functions: __dev_change_flags() to perform the actual changes and __dev_notify_flags() to invoke netdevice notifiers. This will be used by rtnl_link to defer netlink notifications until the device has been fully configured. This changes ordering of some operations, in particular: - netlink notifications are sent after all changes have been performed. As a side effect this surpresses one unnecessary netlink message when the IFF_UP and other flags are changed simultaneously. - The NETDEV_UP/NETDEV_DOWN and NETDEV_CHANGE notifiers are invoked after all changes have been performed. Their relative is unchanged. - net_dmaengine_put() is invoked before the NETDEV_DOWN notifier instead of afterwards. This should not make any difference since both RX and TX are already shut down at this point. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* rtnetlink: handle rtnl_link netlink notifications manuallyPatrick McHardy2010-02-27
| | | | | | | | | | | | | | | In order to support specifying device flags during device creation, we must be able to roll back device registration in case setting the flags fails without sending any notifications related to the device to userspace. This patch changes rollback_registered_many() and register_netdevice() to manually send netlink notifications for devices not handled by rtnl_link and allows to defer notifications for devices handled by rtnl_link until setup is complete. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* rtnetlink: ignore NETDEV_PRE_UP notifier in rtnetlink_event()Patrick McHardy2010-02-27
| | | | | | | | | | | | Commit 3b8bcfd (net: introduce pre-up netdev notifier) added a new notifier which is run before a device is set UP for use by cfg80211. The patch missed to add the new notifier to the ignore list in rtnetlink_event(), so we currently get an unnecessary netlink notification before a device is set UP. Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* fs_enet: add FEC TX buffer alignment workaround for MPC5121Anatolij Gustschin2010-02-27
| | | | | | | | | | | | | MPC5121 FEC requeries 4-byte alignmnent for TX data buffers. This patch is a work around that copies misaligned tx packets to an aligned skb before sending. Signed-off-by: John Rigby <jcrigby@gmail.com> Signed-off-by: Piotr Ziecik <kosmo@semihalf.com> Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
* fs_enet: Add support for MPC512x to fs_enet driverAnatolij Gustschin2010-02-27
| | | | | | | | | | | | Extend the fs_enet driver to support MPC512x FEC. Enable it with CONFIG_FS_ENET_MPC5121_FEC option. Signed-off-by: John Rigby <jcrigby@gmail.com> Signed-off-by: Piotr Ziecik <kosmo@semihalf.com> Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
* fs_enet: use dev_xxx instead of printkAnatolij Gustschin2010-02-27
| | | | | | Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2010-02-27
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
| * b43: fall back gracefully to PIO mode after fatal DMA errorsLinus Torvalds2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This makes the b43 driver just automatically fall back to PIO mode when DMA doesn't work. The driver already told the user to do it, so rather than have the user reload the module with a new flag, just make the driver do it automatically. We keep the message as an indication that something is wrong, but now just automatically fall back to the hopefully working PIO case. (Some post-2.6.33 merge fixups by Larry Finger <Larry.Finger@lwfinger.net> and yours truly... -- JWL) Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * mac80211: fix direct probe loop on ieee80211_work_purgeJuuso Oikarinen2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If authentication has already been performed when the WLAN interface is stopped, (sometimes) the ieee80211_work_purge would corrupt some ieee80211_work-structures. The outcome is this (cleaned up): [ 2252.398681] WARNING: at net/mac80211/work.c:995 ieee80211_work_purge [ 2252.466430] Backtrace: [ 2252.529266] (ieee80211_work_purge+0x0/0xcc [mac80211]) [ 2252.546875] (ieee80211_stop+0x0/0x4c0 [mac80211]) Additionally, one would get this, going on regarless of the WLAN interface state, going on forever: [ 2252.859985] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717525) [ 2253.055419] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717524) [ 2253.250610] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717523) [ 2253.446014] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717522) [ 2253.641357] wlan0: direct probe to 00:90:4c:60:04:00 (try -996717521) Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * netdevice.h: check for CONFIG_WLAN instead of CONFIG_WLAN_80211John W. Linville2010-02-26
| | | | | | | | | | | | | | | | | | | | | | In "wireless: remove WLAN_80211 and WLAN_PRE80211 from Kconfig" I inadvertantly missed a line in include/linux/netdevice.h. I thereby effectively reverted "net: Set LL_MAX_HEADER properly for wireless." by accident. :-( Now we should check there for CONFIG_WLAN instead. Signed-off-by: John W. Linville <linville@tuxdriver.com> Reported-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de> Cc: stable@kernel.org
| * mac80211: use listen interval 5 as defaultHelmut Schaa2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | Currently if a driver does not set hw.max_listen_interval a listen interval of 1 is negotiated with the AP. Thus, the AP could drop buffered frames for us after just one beacon interval which can easily happen with the current powersave and scan implementation. To avoid this issue increase the default interval to 5 which should be a reasonable safe default. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * ath9k: disable RIFS search for AR91xx based chipsFelix Fietkau2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While ath9k does not support RIFS yet, the ability to receive RIFS frames is currently enabled for most chipsets in the initvals. This is causing baseband related issues on AR9160 and AR9130 based chipsets, which can lock up under certain conditions. This patch fixes these issues by overriding the initvals, effectively disabling RIFS for all affected chipsets. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * MAINTAINERS: update mwl8k maintenance statusLennert Buytenhek2010-02-26
| | | | | | | | | | | | | | I am no longer with Marvell. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * Merge branch 'wireless-next-2.6' of ↵John W. Linville2010-02-26
| |\ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
| | * Revert "iwlwifi: Monitor and recover the aggregation TX flow failure"Reinette Chatre2010-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit 1db5950f1d0b82e07371b211a48317b8972da063. The goal of "iwlwifi: Monitor and recover the aggregation TX flow failure" is to first detect when data transmission stalls and then to recover from this situation with a reset of the radio or the firmware, depending on how bad the transmission failures are. Unfortunately we have found that this change causes excessive resets with its current detection algorithm. It also performs its recovery action when none is really needed, like when we are not associated. Revert this change until the issues have been addressed. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
| * | Merge branch 'wireless-2.6' of ↵John W. Linville2010-02-26
| |\ \ | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
| | * | iwlwifi: increase command buffer sizeAbhijeet Kolekar2010-02-23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Increase the buffer size for commands with "huge" bit set. This has been recently observed for 6050 cards where for even with huge bit set few commands were not properly allocated memory with the command overwriting the buffer allocated for it.. Also add a check to see if command size exceeds the maximum allowable size. Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
| * | | Merge branch 'master' of ↵John W. Linville2010-02-26
| |\| | | | |/ | |/| | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: drivers/net/wireless/iwlwifi/iwl-core.h net/mac80211/rate.c
* | | net: Delete isa-skeleton net driverJeff Garzik2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ISA skeleton net driver has been obsolete and unmaintained for many years. Any hardware remotely like ISA will use the platform API and look much more like a PCI driver, and make much better use of netdev APIs such as NAPI. Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | Merge branch 'master' of ↵David S. Miller2010-02-26
|\ \ \ | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-next-2.6
| * | | netfilter: xtables: restore indentationJan Engelhardt2010-02-26
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Patrick McHardy <kaber@trash.net>
| * | | netfilter: nfnetlink_log: fix silly refcount leakAlexey Dobriyan2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Quick fix for memory/module refcount leak. Reference count of listener instance never reaches 0. Start/stop of ulogd2 is enough to trigger this bug! Now, refcounting there looks very fishy in particular this code: if (!try_module_get(THIS_MODULE)) { ... and creation of listener instance with refcount 2, so it may very well be ripped and redone. :-) Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
| * | | IPVS: ip_vs_lblcr: use list headASimon Horman2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Use list_head rather than a custom list implementation. Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Patrick McHardy <kaber@trash.net>
* | | | can: ti hecc module : add platform specific initialization callback.Sriramakrishnan2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CAN module on AM3517 requires programming of IO expander as part of init sequence - to enable CAN PHY. Added platform specific callback to handle phy control(switch on /off). Signed-off-by: Sriramakrishnan <srk@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | | Revert "ethtool: Add n-tuple string length to drvinfo and return it"David S. Miller2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit c79c5ffdce14abb4de3878c5aa8c3c6e5093c69b. As Jeff points out we can't break the user visible interface like this, we need to add this into the reserved[] thing. Signed-off-by: David S. Miller <davem@davemloft.net>
* | | | ipv6: Use 1280 as min MTU for ipv6 forwardingUlrich Weber2010-02-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clients will set their MTU to 1280 if they receive a ICMPV6_PKT_TOOBIG message with an MTU less than 1280. To allow encapsulating of packets over a 1280 link we should always accept packets with a size of 1280 for forwarding even if the path has a lower MTU and fragment the encapsulated packets afterwards. In case a forwarded packet is not going to be encapsulated a ICMPV6_PKT_TOOBIG msg will still be send by ip6_fragment() with the correct MTU. Signed-off-by: Ulrich Weber <uweber@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.2 (git 2.25.0) at 2024-10-01 18:32:11 -0400