aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* isdn: avm: call pci_disable_device() if pci_probe() failedKulikov Vasiliy2010-08-10
| | | | | | | | Driver should call pci_disable_device() if it returns from pci_probe() with error. Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* isdn: avm: call pci_disable_device() if pci_probe() failedKulikov Vasiliy2010-08-10
| | | | | | | | Driver should call pci_disable_device() if it returns from pci_probe() with error. Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* usbnet: rx_submit() should return an error code.David S. Miller2010-08-10
| | | | | | | | | | | | This patch makes rx_submit() return an error code, and makes some call sites that care check the return value. This is important because it lets us properly handle cases where the device isn't ready to handle URB submissions (e.g., when it is autosuspended under some drivers); previously, we would attempt and fail to submit URBs and reschedule ourselves to try and fail again. This patch is against Linus's 2.6 repo commit 45d7f32c7a43cbb9592886d38190e379e2eb2226. Signed-Off-By: Elizabeth Jones <ellyjones@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* pkt_sched: Add some basic qdisc class ops verification. Was: [PATCH] sfq: ↵Jarek Poplawski2010-08-10
| | | | | | | | | add dummy bind/unbind handles Verify in register_qdisc() some basic qdisc class handlers are present. Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* pkt_sched: sch_sfq: Add dummy unbind_tcf and put handles. Was: [PATCH] sfq: ↵Jarek Poplawski2010-08-10
| | | | | | | | | | add dummy bind/unbind handles Add dummy .unbind_tcf and .put qdisc class ops for easier verification. (All other schedulers have it like this.) Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: using too much stackDan Carpenter2010-08-10
| | | | | | | | | qlcnic_pci_info structs are 128 bytes so an array of 8 uses 1024 bytes. That's a lot if you run with 4K stacks. I allocated them with kcalloc() instead. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* qlcnic: clean up qlcnic_init_pci_info()Dan Carpenter2010-08-10
| | | | | | | | | | | | | | In the original code we allocated memory conditionally and freed it in the error handling unconditionally. It turns out that this function is only called during initialization and "adapter->npars" and "adapter->eswitch" are always NULL at the start of the function. I removed those checks. Also since I was cleaning things, I changed the error handling for qlcnic_get_pci_info() and pulled everything in an indent level. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy.c: fix kernel-doc warningsRandy Dunlap2010-08-10
| | | | | | | | | | Fix phy.c kernel-doc notation: Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr' Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/sock.h: add missing kernel-doc notationRandy Dunlap2010-08-10
| | | | | | | | | | | | Add missing kernel-doc notation to struct sock: Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_pid' Warning(include/net/sock.h:324): No description found for parameter 'sk_peer_cred' Warning(include/net/sock.h:324): No description found for parameter 'sk_classid' Warning(include/net/sock.h:324): Excess struct/union/enum/typedef member 'sk_peercred' description in 'sock' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* etherdevice.h: fix kernel-doc typoRandy Dunlap2010-08-10
| | | | | | | | | | Fix etherdevice.h parameter name typo in kernel-doc: Warning(include/linux/etherdevice.h:138): No description found for parameter 'hwaddr' Warning(include/linux/etherdevice.h:138): Excess function parameter 'addr' description in 'dev_hw_addr_random' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* farsync: Fix compile warnings.David S. Miller2010-08-10
| | | | | | | | | | | | | | | drivers/net/wan/farsync.c: In function 'fst_intr_rx': drivers/net/wan/farsync.c:1312: warning: cast to pointer from integer of different size drivers/net/wan/farsync.c: In function 'do_bottom_half_tx': drivers/net/wan/farsync.c:1407: warning: cast to pointer from integer of different size The "skb" and "mem" arguments being passed here are DMA addresses being programmed into the hardware registers, so pass them as the type that they actually are. And use the correct printf formatting in debug logging statements for these things to match the type change. Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* igbvf.txt: Add igbvf DocumentationJeff Kirsher2010-08-08
| | | | | | | | | | | | Adds documentation for the igbvf (igb virtual function driver). v2: - Removed trailing white space - Removed Ethtool version info Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb.txt: Add igb documentationJeff Kirsher2010-08-08
| | | | | | | | | | | | | Add documentation for the igb networking driver. v2: - Removed trailing white space - Removed Ethtool version info - Removed LRO kernel version info Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* e100/e1000*/igb*/ixgb*: Add missing read memory barrierJeff Kirsher2010-08-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on patches from Sonny Rao and Milton Miller... Combined the patches to fix up clean_tx_irq and clean_rx_irq. The PowerPC architecture does not require loads to independent bytes to be ordered without adding an explicit barrier. In ixgbe_clean_rx_irq we load the status bit then load the packet data. With packet split disabled if these loads go out of order we get a stale packet, but we will notice the bad sequence numbers and drop it. The problem occurs with packet split enabled where the TCP/IP header and data are in different descriptors. If the reads go out of order we may have data that doesn't match the TCP/IP header. Since we use hardware checksumming this bad data is never verified and it makes it all the way to the application. This bug was found during stress testing and adding this barrier has been shown to fix it. The bug can manifest as a data integrity issue (bad payload data) or as a BUG in skb_pull(). This was a nasty bug to hunt down, if people agree with the fix I think it's a candidate for stable. Previously Submitted to e1000-devel only for ixgbe http://marc.info/?l=e1000-devel&m=126593062701537&w=3 We've now seen this problem hit with other device drivers (e1000e mostly) So I'm resubmitting with fixes for other Intel Device Drivers with similar issues. CC: Milton Miller <miltonm@bga.com> CC: Anton Blanchard <anton@samba.org> CC: Sonny Rao <sonnyrao@us.ibm.com> CC: stable <stable@kernel.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ixgbe: fix build error with FCOE_CONFIG without DCB_CONFIGJohn Fastabend2010-08-08
| | | | | | | | | | | | | | | | | | Building ixgbe without DCB_CONFIG and FCOE_CONFIG will cause a build error. This resolves the build error by wrapping the fcoe.up in CONFIG_IXGBE_DCB ifdefs. Also frames were being priority VLAN tagged even without DCB enabled. This fixes this so that 8021Q priority tags are only added with DCB actually enabled. Reported-by: divya <dipraksh@linux.vnet.ibm.com> Reported-by: Jon Mason <jon.mason@exar.com> Signed-off-by: John Fastabend <john.r.fastabend@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Tested-by: Ross Brattain <ross.b.brattain@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netxen: protect tx timeout recovery by rtnl lockAmit Kumar Salecha2010-08-08
| | | | | Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* isdn: gigaset: use after freeDan Carpenter2010-08-08
| | | | | | | I moved the kfree(cb) below the dereferences. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* isdn: gigaset: add missing unlockDan Carpenter2010-08-08
| | | | | | | | We should unlock here. This is the only place where we return from the function with the lock held. The caller isn't expecting it. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* solos-pci: Fix race condition in tasklet RX handlingDavid Woodhouse2010-08-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We were seeing faults in the solos-pci receive tasklet when packets arrived for a VCC which was currently being closed: [18842.727906] EIP: [<e082f490>] br2684_push+0x19/0x234 [br2684] SS:ESP 0068:dfb89d14 [18845.090712] [<c13ecff3>] ? do_page_fault+0x0/0x2e1 [18845.120042] [<e082f490>] ? br2684_push+0x19/0x234 [br2684] [18845.153530] [<e084fa13>] solos_bh+0x28b/0x7c8 [solos_pci] [18845.186488] [<e084f711>] ? solos_irq+0x2d/0x51 [solos_pci] [18845.219960] [<c100387b>] ? handle_irq+0x3b/0x48 [18845.247732] [<c10265cb>] ? irq_exit+0x34/0x57 [18845.274437] [<c1025720>] tasklet_action+0x42/0x69 [18845.303247] [<c102643f>] __do_softirq+0x8e/0x129 [18845.331540] [<c10264ff>] do_softirq+0x25/0x2a [18845.358274] [<c102664c>] _local_bh_enable_ip+0x5e/0x6a [18845.389677] [<c102666d>] local_bh_enable+0xb/0xe [18845.417944] [<e08490a8>] ppp_unregister_channel+0x32/0xbb [ppp_generic] [18845.458193] [<e08731ad>] pppox_unbind_sock+0x18/0x1f [pppox] This patch uses an RCU-inspired approach to fix it. In the RX tasklet's find_vcc() function we first refuse to use a VCC which already has the ATM_VF_READY bit cleared. And in the VCC close function, we synchronise with the tasklet to ensure that it can't still be using the VCC before we continue and allow the VCC to be destroyed. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Tested-by: Nathan Williams <nathan@traverse.com.au> Cc: stable@kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
* pkt_sched: Fix sch_sfq vs tcf_bind_filter oopsJarek Poplawski2010-08-08
| | | | | | | | | | | | | Since there was added ->tcf_chain() method without ->bind_tcf() to sch_sfq class options, there is oops when a filter is added with the classid parameter. Fixes commit 7d2681a6ff4f9ab5e48d02550b4c6338f1638998 netdev thread: null pointer at cls_api.c Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Reported-by: Franchoze Eric <franchoze@yandex.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: disable preemption before call smp_processor_id()Changli Gao2010-08-07
| | | | | | | | | | | Although netif_rx() isn't expected to be called in process context with preemption enabled, it'd better handle this case. And this is why get_cpu() is used in the non-RPS #ifdef branch. If tree RCU is selected, rcu_read_lock() won't disable preemption, so preempt_disable() should be called explictly. Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* tcp: no md5sig option size check bugDmitry Popov2010-08-07
| | | | | | | | | tcp_parse_md5sig_option doesn't check md5sig option (TCPOPT_MD5SIG) length, but tcp_v[46]_inbound_md5_hash assume that it's at least 16 bytes long. Signed-off-by: Dmitry Popov <dp@highloadlab.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2010-08-06
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
| * iwlwifi: fix locking assertionsJohannes Berg2010-08-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | spin_is_locked() can return zero on some (UP?) configurations because locks don't exist, and that causes an endless amount of warnings. Use lockdep_assert_held() instead, which has two advantages: 1) it verifies the current task is holding the lock or mutex 2) it compiles away completely when lockdep is not enabled Cc: stable@kernel.org [2.6.34+, maybe only parts of patch] Reported-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * iwlwifi: fix TX tracerJohannes Berg2010-08-06
| | | | | | | | | | | | | | | | | | | | The TX tracing code copies with the wrong length, which will typically copy too little data. Fix this by using the correct length variable. Cc: stable@kernel.org [2.6.32+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * rtl8180: avoid potential NULL deref in rtl8180_beacon_workJohn W. Linville2010-08-05
| | | | | | | | | | | | | | ieee80211_beacon_get can return NULL... Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: stable@kernel.org
| * ath9k: Remove myself from the MAINTAINERS listSujith2010-08-05
| | | | | | | | | | | | | | So long. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * libertas: scan before assocation if no BSSID was givenDan Williams2010-08-05
| | | | | | | | | | | | | | | | | | | | | | | | Fix this leftover TODO from the cfg80211 conversion by doing a scan if cfg80211 didn't pass in the BSSID for us. Since the scan code uses so much of the cfg80211_scan_request structure to build up the firmware command, we just fake one when the scan request is triggered internally. But we need to make sure that internal 'fake' cfg82011 scan request does not get back to cfg82011 via cfg80211_scan_done(). Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * libertas: fix association with some APs by using extended ratesDan Williams2010-08-05
| | | | | | | | | | | | | | | | | | | | | | Some APs get pissy if you don't send the firmware the extended rates in the association request's rates TLV. Found this on a Linksys WRT54G v2; it denies association with status code 18 unless you add the extended rates too. The old driver did this, but it got lost in the cfg80211 conversion. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * libertas: get the right # of scanned BSSesDan Williams2010-08-05
| | | | | | | | | | | | | | | | Let's actually check the right field in the command response; and if there aren't any reported BSSes, exit early with success. Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * Merge branch 'master' of ↵John W. Linville2010-08-05
| |\ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-next-2.6
| | * Bluetooth: Check result code of L2CAP information responseVille Tervo2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | Check result code of L2CAP information response. Otherwise it would read invalid feature mask and access invalid memory. Signed-off-by: Ville Tervo <ville.tervo@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
| | * Bluetooth: Don't send RFC for Basic Mode if only it is supportedGustavo F. Padovan2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the remote side doesn't support Enhanced Retransmission Mode neither Streaming Mode, we shall not send the RFC option. Some devices that only supports Basic Mode do not understanding the RFC option. This patch fixes the regression found with these devices. Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
| | * Bluetooth: Remove __exit from rfcomm_cleanup_ttys()Gustavo F. Padovan2010-07-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | rfcomm_cleanup_ttys() is also called from rfcomm_init(), so it can't have __exit. Reported-by: Mat Martineau <mathewm@codeaurora.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
| | * Bluetooth: Use list_head for HCI blacklist headDavid Miller2010-07-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | The bdaddr in the list root is completely unused and just taking up space. Signed-off-by: David S. Miller <davem@davemloft.net> Tested-by: Johan Hedberg <johan.hedberg@nokia.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
| * | iwlagn: Improve aggregation failure error messagesAndy Lutomirski2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 82ca9341763107615a15da6e59b9535d49eb91c3 added scary looking but harmless error messages. Make them clearer and make the actual failure message show up with the same severity as the harmless one. Signed-off-by: Andy Lutomirski <luto@mit.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | rt2x00: do not use PCI resources before pci_enable_device()Kulikov Vasiliy2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | IRQ and resource[] may not have correct values until after PCI hotplug setup occurs at pci_enable_device() time. The semantic match that finds this problem is as follows: // <smpl> @@ identifier x; identifier request ~= "pci_request.*|pci_resource.*"; @@ ( * x->irq | * x->resource | * request(x, ...) ) ... *pci_enable_device(x) // </smpl> Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | mac80211: Fix compilation warning when CONFIG_INET is not setJuuso Oikarinen2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | The warning is: net/mac80211/main.c:688: warning: label ‘fail_ifa’ defined but not used Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | wireless: ipw2100: check result of kzalloc()Christoph Fritz2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | If kzalloc() fails return with -ENOMEM from ipw2100_net_init() which is called by register_netdev. CC: Dan Carpenter <error27@gmail.com> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | ath9k: fix erased ieee80211_rx_status.mactimeJan Friedrich2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ath9k_rx_skb_preprocess nulls rxs and the mactime is never set again - mactime is always 0. This causes problems in IBSS mode. ieee80211_rx_bss_info uses mactime to decide if an IBSS merge is needed. Without this patch the merge is triggered by each beacon received. This can be recognized by the "beacon TSF higher than local TSF - IBSS merge with BSSID" log message accompanying each beacon. This problem was not completely fixed in commit a6d2055b02dde1067075795274672720baadd3ca and is not a stable kernel fix. It is solely intended for wireless-testing. Signed-off-by: Jan Friedrich <jft@dev2day.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | p54pci: Add PCI ID for SMC2802WLarry Finger2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | The SMC2802W appears to work with p54pci. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: David Cozatt <olbrannon@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | ath9k: fix an issue in ath_atx_tid paused flag managementLorenzo Bianconi2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I noticed a possible issue in the paused flag management of the ath_atx_tid data structure. In particular, in a noisy environment and under heavy load, I observed that the AGGR session establishment could fail several times consecutively causing values of the paused flag greater than one for this TID (ath_tx_pause_tid is called more than once from ath_tx_aggr_start). Considering that the session for this TID can not be established also after the mac80211 stack calls the ieee80211_agg_tx_operational() since the ath_tx_aggr_resume() lowers the paused flag only by one. This patch also replaces some BUG_ON calls with WARN_ON, as even if these unlikely conditions happen, it's not fatal enough to justify a BUG_ON. Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | ath9k_hw: Fix regulatory CTL index usage for AR9003Luis R. Rodriguez2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AR9003 was not relying on the CTL indexes from the EEPROM for capping the max output power. The CTL indexes from the EEPROM provide calibrated limits for output power for each tested and supported frequency. Without this the device operates at a power level which only conforms to the transmit spectrum mask as specified by IEEE Annex I.2.3. The regulatory limit by CRDA is always used but does not provide calibrated values for optimal performance, specially on band edges. Using the calibrated data from the EEPROM ensures the device operates at optimal output power while still ensuring proper regulatory compliance. The device uses the minimum of these tree values, the value from CRDA, the calibrated value from CTL indexex, and the value to conform to the IEEE transmit spectrum mask. Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | net: wl12xx: do not use kfree'd memoryKulikov Vasiliy2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | wl1271_dump() uses cmd after kfree(cmd). Move kfree() just after wl1271_dump(). Signed-off-by: Kulikov Vasiliy <segooon@gmail.com> Acked-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | iwlagn: fix typo in ucode_bt_stats_read debugfsWey-Yi Guy2010-08-04
| | | | | | | | | | | | | | | | | | | | | small typo fix in ucode_bt_stats_read debugfs file Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | iwlwifi: BA scd_flow not match condition detectedWey-Yi Guy2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is a uCode bug which cause the tx queue id not match scd_flow in compressed block ack frame, and it need to be addressed in uCode. Currently, driver will log the information when it happen. Since it is possible happen very often and we do not want to fill the syslog, so don't enable the logging by default. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | iwlwifi: fix compile warningJohannes Berg2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When iwlwifi is compiled w/o debug, we get this warning: iwl-agn.c: In function ‘iwlagn_load_firmware’: iwl-agn.c:2014: warning: passing argument 3 of ‘iwl_print_hex_dump’ discards qualifiers from pointer target type iwl-debug.h:73: note: expected ‘void *’ but argument is of type ‘const u8 *’ because the const qualifier is missing in the inline stub. Fix this. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | ath9k_hw: fix a noise floor calibration related race conditionFelix Fietkau2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On AR5008-AR9002, other forms of calibration must not be started while the noise floor calibration is running, as this can create invalid readings which were sometimes not even recoverable by any further calibration attempts. This patch also ensures that the result of noise floor measurements are processed faster and also allows the result of the initial calibration on reset to make it into the NF history buffer Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | ath9k_hw: clean up per-channel calibration dataFelix Fietkau2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The noise floor history buffer is currently not kept per channel, which can lead to problems when changing channels from a clean channel to a noisy one. Also when switching from HT20 to HT40, the noise floor history buffer is full of measurements, but none of them contain data for the extension channel, which it needs quite a bit of time to recover from. This patch puts all the per-channel calibration data into a single data structure, and gives the the driver control over whether that is used per-channel or even not used for some channels. For ath9k_htc, I decided to keep this per-channel in order to avoid creating regressions. For ath9k, the data is kept only for the operating channel, which saves some space. ath9k_hw takes care of wiping old data when the operating channel or its channel flags change. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | ath9k: prevent calibration during off-channel activityFelix Fietkau2010-08-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously the software scan callback was used to indicate to the hardware, when it was safe to calibrate. This didn't really work properly, because it depends on a specific order of software scan callbacks vs. channel changes. Also, software scans are not the only thing that triggers off-channel activity, so it's better to use the newly added indication from mac80211 for this and not use the software scan callback for anything calibration related. This fixes at least some of the invalid noise floor readings that I've seen in AP mode on AR9160 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-03-02 00:13:01 -0500