aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* [PATCH] ide: fix revision comparison in ide_in_drive_listKirill Smelkov2006-10-03
| | | | | | | | | | | Fix ide_in_drive_list: drive_table->id_firmware should be searched *in* id->fw_rev, not vice versa. Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Enable cdrom dma access with pdc20265_oldTobias Oed2006-10-03
| | | | | | | | | | | | | | | | | | | | This patch allows me to use dma with my cd/dvd attached to my on board pdc20265 ide controller Alan sayeth: Looks sane. Would be nice to know if there is any documentation supporting this hack being safe but the logic makes sense. The LBA48 case faces the same problem - the state machine gets confused about the transfer length and needs kicking Signed-off-by: Tobias Oed <tobiasoed@hotmail.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Jens Axboe <axboe@suse.de> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ide_dma_speed() fixesSergei Shtylyov2006-10-03
| | | | | | | | | | | | | | ide_dma_speed() fails to actually honor the IDE drivers' mode support masks) because of the bogus checks -- thus, selecting the DMA transfer mode that the driver explicitly refuses to support is possible. Additionally, there is no check for validity of the UltraDMA mode data in the drive ID, and the function is misdocumented. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Make number of IDE interfaces configurableMatt Mackall2006-10-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make IDE_HWIFS configurable if EMBEDDED This lets us lop as much as 16k off an x86 build. It's a little ugly, but it's dead simple. Note the fix for HWIFS < 2. Sizing interfaces dynamically unfortunately turns out to be pretty major surgery. add/remove: 0/1 grow/shrink: 0/11 up/down: 0/-16182 (-16182) function old new delta ide_hwifs 16920 1692 -15228 init_irq 1113 750 -363 ideprobe_init 283 138 -145 ide_pci_setup_ports 1329 1193 -136 save_match 85 - -85 ide_register_hw_with_fixup 367 287 -80 ide_setup 1364 1308 -56 is_chipset_set 40 4 -36 create_proc_ide_interfaces 225 205 -20 init_ide_data 84 67 -17 ide_probe_for_cmd640x 1198 1183 -15 ide_unregister 1452 1451 -1 Signed-off-by: Matt Mackall <mpm@selenic.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IDE error handling fixesHua Zhong2006-10-03
| | | | | | | | | | | | | | | | | | | | | In 2.6.15.1 I encountered some IDE crashes when unplugging IDE cables to emulate disk errors. Below is a patch against 2.6.16 which I think still applies. 1. The first BUG_ON could trigger when a PREFLUSH IO fails (it would fail the original barrier request which hasn't been marked REQ_STARTED yet). 2. the rq could have been dequeued already (same as 1). 3. HWGROUP(drive)->rq could be NULL because of the ide_error() several lines earlier. Signed-off-by: Hua Zhong <hzhong@gmail.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IDE: always release DMA engineSergei Shtylylov2006-10-03
| | | | | | | | | | | | | Release the DMA engine for the custom mapping IDE drivers also (for example, siimage.c does allocate it in both I/O-mapped and custom-mapped modes). Remove useless code from the error path of ide_allocate_dma_engine(). Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IDE: claim extra DMA ports regardless of channelSergei Shtylylov2006-10-03
| | | | | | | | | | | | | | - Claim extra DMA I/O ports regardless of what IDE channels are present/enabled. - Remove extra ports handling from ide_mapped_mmio_dma() since it's not applicable to the custom-mapping IDE drivers. Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] non-libata driver for Jmicron devicesAlan Cox2006-10-03
| | | | | | | | | | | | Less functional than libata this just uses the merged interface provided for dumb legacy OS's. This is basically a bridge for people not yet ready to use libata for some reason or another. Port visibility is entirely dependant on the BIOS setup. Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] scheduler: NUMA aware placement of sched_group_allnodesChristoph Lameter2006-10-03
| | | | | | | | | | | | When the per cpu sched domains are build then they also need to be placed on the node where the cpu resides otherwise we will have frequent off node accesses which will slow down the system. Signed-off-by: Christoph Lameter <clameter@sgi.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sched: fixing wrong comment for find_idlest_cpu()Satoru Takeuchi2006-10-03
| | | | | | | | | Fixing wrong comment for find_idlest_cpu(). Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sched: cleanup sched_group cpu_power setupSiddha, Suresh B2006-10-03
| | | | | | | | | | | | | | | | | | | | | Up to now sched group's cpu_power for each sched domain is initialized independently. This made the setup code ugly as the new sched domains are getting added. Make the sched group cpu_power setup code generic, by using domain child field and new domain flag in sched_domain. For most of the sched domains(except NUMA), sched group's cpu_power is now computed generically using the domain properties of itself and of the child domain. sched groups in NUMA domains are setup little differently and hence they don't use this generic mechanism. Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sched: introduce child field in sched_domainSiddha, Suresh B2006-10-03
| | | | | | | | | | | | | | | Introduce the child field in sched_domain struct and use it in sched_balance_self(). We will also use this field in cleaning up the sched group cpu_power setup(done in a different patch) code. Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sched: don't print migration cost when only 1 CPUDave Jones2006-10-03
| | | | | | | | | | If only a single CPU is present, printing this doesn't make much sense. Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sched: remove unnecessary sched group allocationsSiddha, Suresh B2006-10-03
| | | | | | | | | | | | | Remove dynamic sched group allocations for MC and SMP domains. These allocations can easily fail on big systems(1024 or so CPUs) and we can live with out these dynamic allocations. [akpm@osdl.org: build fix] Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] sched: force /sbin/init off isolated cpusNick Piggin2006-10-03
| | | | | | | | | | | | | | | | | | | | | | | | Force /sbin/init off isolated cpus (unless every CPU is specified as an isolcpu). Users seem to think that the isolated CPUs shouldn't have much running on them to begin with. That's fair enough: intuitive, I guess. It also means that the cpu affinity masks of tasks will not include isolcpus by default, which is also more intuitive, perhaps. /sbin/init is spawned from the boot CPU's idle thread, and /sbin/init starts the rest of userspace. So if the boot CPU is specified to be an isolcpu, then prior to this patch, all of userspace will be run there. (throw in a couple of plausible devinit -> cpuinit conversions I spotted while we're here). Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Dimitri Sivanich <sivanich@sgi.com> Acked-by: Paul Jackson <pj@sgi.com> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] pata_hpt366: fix typoOGAWA Hirofumi2006-10-03
| | | | | | | | | | | | | | | | | | | | | switch(reg1 & 0x700) { case 5: info_hpt366.private_data = &hpt366_40; break; case 9: info_hpt366.private_data = &hpt366_25; break; default: info_hpt366.private_data = &hpt366_33; break; } The above runs always default part. It should be "(reg1 & 0x700) >> 8". Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] MAINTAINERS: Removes duplicated entryLuiz Fernando N. Capitulino2006-10-03
| | | | | | | | | | The 'STABLE BRANCH' entry is duplicated, remove it. Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br> Cc: Greg KH <greg@kroah.com> Cc: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ia64: note requirement for 8250_pnp, now that 8250_acpi is goneBjorn Helgaas2006-10-03
| | | | | | | | | | | | | We removed 8250_acpi in 2.6.17. If we don't have PNPACPI turned on, we won't find any ACPI serial devices, so mention this requirement in the troubleshooting part of the documentation. CONFIG_PNPACPI is already turned on in all the relevant defconfigs. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Acked-by: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] IPMI: allow user to override the kernel IPMI daemon enableCorey Minyard2006-10-03
| | | | | | | | | | | | | | | After the previous patch to disable the kernel IPMI daemon if interrupts were available, the issue of broken hardware was raised, and a reasonable request to add an override was mode. So here it is. Allow the user to force the kernel ipmi daemon on or off. This way, hardware with broken interrupts or users that are not concerned with performance can turn it on or off to their liking. [akpm@osdl.org: save 4 bytes in vmlinux] Signed-off-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Add Pekka to CREDITSPekka Enberg2006-10-03
| | | | | | | | | | | | | | | | Whomever said... "When you meet someone now who is writing a compiler or hacking a Unix kernel, at least you know they're not just doing it to pick up chicks." ...has obviously never met a _Linux_ kernel hacker. Anyway, sometimes people confuse my email addresses, which is why I really should add the proper one to CREDITS ;-). Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] restore parport_pc probing on powermacOlaf Hering2006-10-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The last change for partport_pc did fix the common case for all PowerMacs, but it broke the case for PCI multiport IO cards. In fact, the config option CONFIG_PARPORT_PC_SUPERIO=y lead to a hard crash when cups probed the parport driver. It enables the winbond and smsc probing. Remove the PARPORT_BASE check again, parport_pc_find_nonpci_ports() will take care of it. All powerpc configs should have CONFIG_PARPORT_PC_SUPERIO=n, the code did not find anything on the chrp boards we tested it on. Tested on a G4/466 with a PCI card: 0001:10:13.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550]) Subsystem: Timedia Technology Co Ltd Unknown device 5079 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 53 Region 0: I/O ports at f2000800 [size=32] Region 2: I/O ports at f2000870 [size=8] Region 3: I/O ports at f2000860 [size=8] Signed-off-by: Olaf Hering <olaf@aepfle.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Adam Belay <ambx1@neo.rr.com> Cc: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ISDN warning fixesAlan Cox2006-10-03
| | | | | | | | | | | | | | Clean up warnings in drivers/isdn by using long not int for the values where we pass void * and cast to integer types. The code is ok (ok passing the stuff this way isn't pretty but the code is valid). In all the cases I checked out the right thing happens anyway but this removes all the warnings. Signed-off-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] schedule ftape removalJeff Garzik2006-10-03
| | | | | | Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] drivers/char/ip2: kill unused code, labelJeff Garzik2006-10-03
| | | | | | | | | | | | | | | | Kill warning: drivers/char/ip2/ip2main.c: In function ‘ip2_loadmain’: drivers/char/ip2/ip2main.c:782: warning: label ‘out_class’ defined but not used This driver's initialization (and cleanup of errors during init) is extremely convoluted, and could stand to be transformed into the standard unwinding-goto style of error cleanup. Signed-off-by: Jeff Garzik <jeff@garzik.org> Acked-by: Michael H. Warfield <mhw@wittsend.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] ipmi: fix uninitialized data bugJeff Garzik2006-10-03
| | | | | | | | | | | | | | | | gcc issues the following warning: drivers/char/ipmi/ipmi_si_intf.c: In function ‘init_ipmi_si’: drivers/char/ipmi/ipmi_si_intf.c:1729: warning: ‘data.irq’ may be used uninitialized in this function This is indeed a bug. data.irq is completely uninitialized in some code paths. Worse than that, data from a previous decode_dmi() run can easily leak through successive calls. Signed-off-by: Jeff Garzik <jeff@garzik.org> Acked-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] fs/eventpoll: error handling micro-cleanupJeff Garzik2006-10-03
| | | | | | | | | | | While reviewing the 'may be used uninitialized' bogus gcc warnings, I noticed that an error code assignment was only needed if an error had actually occured. Signed-off-by: Jeff Garzik <jeff@garzik.org> Cc: Davide Libenzi <davidel@xmailserver.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] kernel-doc for kernel/resource.cRandy Dunlap2006-10-03
| | | | | | | | Add kernel-doc function headers in kernel/resource.c and use them in DocBook. Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] kernel-doc for kernel/dma.cRandy Dunlap2006-10-03
| | | | | | | | | | | Add kernel-doc function headers in kernel/dma.c and use it in DocBook. Clean up kernel-doc in mca_dma.h (the colon (':') represents a section header). Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] low performance of lib/sort.ckeios2006-10-03
| | | | | | | | | | | | | It is a non-standard heap-sort algorithm implementation because the index of child node is wrong . The sort function still outputs right result, but the performance is O( n * ( log(n) + 1 ) ) , about 10% ~ 20% worse than standard algorithm. Signed-off-by: keios <keios.cn@gmail.com> Acked-by: Matt Mackall <mpm@selenic.com> Acked-by: Zou Nan hai <nanhai.zou@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Create kallsyms_lookup_size_offset()Franck Bui-Huu2006-10-03
| | | | | | | | | | | | | | | | | | | Some uses of kallsyms_lookup() do not need to find out the name of a symbol and its module's name it belongs. This is specially true in arch specific code, which needs to unwind the stack to show the back trace during oops (mips is an example). In this specific case, we just need to retreive the function's size and the offset of the active intruction inside it. Adds a new entry "kallsyms_lookup_size_offset()" This new entry does exactly the same as kallsyms_lookup() but does not require any buffers to store any names. It returns 0 if it fails otherwise 1. Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] FRV: Permit large kmalloc allocations [try #2]David Howells2006-10-03
| | | | | | | | | Permit kmalloc() to make allocations of up to 32MB if so configured. This may be useful under NOMMU conditions where vmalloc() can't do this. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] VFS: Make filldir_t and struct kstat deal in 64-bit inode numbersDavid Howells2006-10-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These patches make the kernel pass 64-bit inode numbers internally when communicating to userspace, even on a 32-bit system. They are required because some filesystems have intrinsic 64-bit inode numbers: NFS3+ and XFS for example. The 64-bit inode numbers are then propagated to userspace automatically where the arch supports it. Problems have been seen with userspace (eg: ld.so) using the 64-bit inode number returned by stat64() or getdents64() to differentiate files, and failing because the 64-bit inode number space was compressed to 32-bits, and so overlaps occur. This patch: Make filldir_t take a 64-bit inode number and struct kstat carry a 64-bit inode number so that 64-bit inode numbers can be passed back to userspace. The stat functions then returns the full 64-bit inode number where available and where possible. If it is not possible to represent the inode number supplied by the filesystem in the field provided by userspace, then error EOVERFLOW will be issued. Similarly, the getdents/readdir functions now pass the full 64-bit inode number to userspace where possible, returning EOVERFLOW instead when a directory entry is encountered that can't be properly represented. Note that this means that some inodes will not be stat'able on a 32-bit system with old libraries where they were before - but it does mean that there will be no ambiguity over what a 32-bit inode number refers to. Note similarly that directory scans may be cut short with an error on a 32-bit system with old libraries where the scan would work before for the same reasons. It is judged unlikely that this situation will occur because modern glibc uses 64-bit capable versions of stat and getdents class functions exclusively, and that older systems are unlikely to encounter unrepresentable inode numbers anyway. [akpm: alpha build fix] Signed-off-by: David Howells <dhowells@redhat.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] pid.h cleanupAndrew Morton2006-10-03
| | | | | | | Make the pid.h macros look less revolting in an 80-col window. Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] Add unifdef to gitignorePaul Mundt2006-10-02
| | | | | | | | This seems to have been missed when unifdef went in via Sam's tree.. Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] hp100: fix conditional compilation messJeff Garzik2006-10-02
| | | | | | | | | | | The previous hp100 changeset attempted to kill warnings, but was only tested on !CONFIG_ISA platforms. The correct conditional compilation setup involves tested CONFIG_ISA rather than just MODULE. Fixes link on CONFIG_ISA platforms (i386) in current -git. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] revert "insert IOAPIC(s) and Local APIC into resource map"Andrew Morton2006-10-02
| | | | | | | | | | | | | | Commit 54dbc0c9ebefb38840c6b07fa6eabaeb96c921f5 is causing various people's machines to fail to map PCI resources. Revert it in preparation for addressing the show-APICs-in-/proc/iomem requirement in a different manner. Cc: Aaron Durbin <adurbin@google.com> Cc: Andi Kleen <ak@muc.de> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Merge branch 'for-linus' of ↵Linus Torvalds2006-10-02
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/ehca: Tweak trace message format IB/ehca: Fix device registration IB/ipath: Fix RDMA reads RDMA/cma: Optimize error handling RDMA/cma: Eliminate unnecessary remove_list RDMA/cma: Set status correctly on route resolution error RDMA/cma: Fix device removal race RDMA/cma: Fix leak of cm_ids in case of failures
| * IB/ehca: Tweak trace message formatHoang-Nam Nguyen2006-10-02
| | | | | | | | | | | | | | Add an extra space to make things more readable. Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * IB/ehca: Fix device registrationHoang-Nam Nguyen2006-10-02
| | | | | | | | | | | | | | | | | | | | Move the call to ib_register_device() later, since a device should not be registered until it is completely read to be used. This fixes crashes that occur if an upper-layer driver such as IPoIB is loaded before the ehca module. Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * IB/ipath: Fix RDMA readsRalph Campbell2006-10-02
| | | | | | | | | | | | | | | | | | | | The PSN used to generate the request following a RDMA read was incorrect and some state booking wasn't maintained correctly. This patch fixes that. Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com> Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
| * RDMA/cma: Optimize error handlingKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | | | | | Reorganize code relating to cma_get_net_info() and rdam_create_id() to optimize error case handling (no need to alloc memory/etc. as part of rdma_create_id() if input parameters are wrong). Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Eliminate unnecessary remove_listKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | | | Eliminate remove_list by using list_del_init() instead during device removal handling. Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Set status correctly on route resolution errorSean Hefty2006-10-02
| | | | | | | | | | | | | | | | On reporting a route error, also include the status for the error, rather than indicating a status of 0 when an error has occurred. Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Fix device removal raceKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The race is as follows: A process : cma_process_remove() calls cma_remove_id_dev(), which sets id state to CMA_DEVICE_REMOVAL and calls wait_event(dev_remove). B process : cma_req_handler() had incremented dev_remove, and calls cma_acquire_ib_dev() and on failure calls cma_release_remove(), which does a wake_up of cma_process_remove(). Then cma_req_handler() calls rdma_destroy_id(); A Process : cma_remove_id_dev() gets woken and checks the state of id, and since it is still (wrongly) CMA_DEVICE_REMOVAL, it calls notify_user(id) and if that fails, the caller - cma_process_remove() calls rdma_destroy_id(id). Two processes can call rdma_destroy_id(), resulting in one de-referencing kfreed id_priv. Fix is for process B to set CMA_DESTROYING in cma_req_handler() so that process A will return instead of doing a rdma_destroy_id(). Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
| * RDMA/cma: Fix leak of cm_ids in case of failuresKrishna Kumar2006-10-02
| | | | | | | | | | | | | | | | cma_connect_ib() and cma_connect_iw() leak cm_id's in failure cases. Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdogLinus Torvalds2006-10-02
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: [WATCHDOG] improve machzwd detection [WATCHDOG] use ENOTTY instead of ENOIOCTLCMD in ioctl() [WATCHDOG] s3c24XX nowayout [WATCHDOG] pnx4008: add cpu_relax() [WATCHDOG] pnx4008_wdt.c - spinlock fixes. [WATCHDOG] pnx4008_wdt.c - remove patch [WATCHDOG] pnx4008_wdt.c - nowayout patch [WATCHDOG] pnx4008: add watchdog support [WATCHDOG] i8xx_tco remove pci_find_device. [WATCHDOG] alim remove pci_find_device
| * | [WATCHDOG] improve machzwd detectionDave Jones2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On a machine with no machzwd, loading the module prints out.. machzwd: MachZ ZF-Logic Watchdog driver initializing. 0xffff machzwd: Watchdog using action = RESET - the 0xffff printk is unnecessary - 0xffff seems to be 'hardware not present' - fix CodingStyle. (This driver could use some more work here) Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Signed-off-by: Andrew Morton <akpm@osdl.org>
| * | [WATCHDOG] use ENOTTY instead of ENOIOCTLCMD in ioctl()Samuel Tardieu2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Return ENOTTY instead of ENOIOCTLCMD in user-visible ioctl() results The watchdog drivers used to return ENOIOCTLCMD for bad ioctl() commands. ENOIOCTLCMD should not be visible by the user, so use ENOTTY instead. Signed-off-by: Samuel Tardieu <sam@rfc1149.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org>
| * | [WATCHDOG] s3c24XX nowayoutBen Dooks2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the driver is not configured for `no way out`, then the open method should not automatically allow the setting of allow_close to CLOSE_STATE_ALLOW. The setting of allow_close nullifies the use of the magic close via the write path. It means that in the default state, the watchdog will shut-down even if the magic close has not been issued. Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| * | [WATCHDOG] pnx4008: add cpu_relax()Vitaly Wool2006-10-02
| | | | | | | | | | | | | | | | | | | | | | | | Added cpu_relax as suggested by Alan Cox. Signed-off-by: Vitaly Wool <vitalywool@gmail.com> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-17 22:20:48 -0500