| Commit message (Collapse) | Author | Age |
|---|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
[ALSA] soc - wm9712 - checkpatch fixes
[ALSA] pcsp - Fix more dependency
[ALSA] hda - Add support of Medion RIM 2150
[ALSA] ASoC: Add drivers for the Texas Instruments OMAP processors
[ALSA] ice1724 - Enable watermarks
[ALSA] Add MPU401_INFO_NO_ACK bitflag
|
| | |
| |
| |
| |
| | |
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| | |
| |
| |
| |
| |
| | |
Added the missing dependency and select for snd-pcsp driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Added the support of Medion RIM 2150 laptop with ALC880 codec.
ALSA bug#3708:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3708
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add common OMAP ASoC drivers and machine driver for Nokia N810. Currently
supported features are:
- Covers OMAPs from 1510 to 2420
- Common DMA driver
- DAI link driver using McBSP port in I2S mode
- Basic machine driver for Nokia N810
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Enable watermarks settings (previously commented out) for MPU RX/TX.
Otherwise irqs aren't issued properly.
Tested-by: Pavel Hofman <pavel.hofman@insite.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
Added MPU401_INFO_NO_ACK bitflag to ignore the ACK check for UART
commands. VT172x doesn't handle ACK commands, for example.
Tested-by: Pavel Hofman <pavel.hofman@insite.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes:
x86: fix PCI MSI breaks when booting with nosmp
x86: vget_cycles() __always_inline
x86: add more boot protocol documentation
bootprotocol: cleanup
x86: fix warning in "x86: clean up vSMP detection"
x86: !x & y typo in mtrr code
|
| | | |
| | |
| | |
| | |
| | |
| | | |
set up sane APIC state even in the nosmp case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Mark vget_cycles() as __always_inline, so gcc is never tempted to make
the vsyscall vread_tsc() dive into kernel text, with resulting SIGSEGV.
This was a self-inflicted wound: I've not seen that happen with unhacked
sources; but for debug reasons I'd changed my x86/Makefile to compile
no-unit-at-a-time, and that in conjunction with OPTIMIZE_INLINING=y
ended up with vget_cycles() in kernel text. Perhaps it can happen
in other ways: safer to use __always_inline.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | | |
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The function detect_vsmp_box is a void function in the PCI case.
Change the !PCI stub to void too.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | |/
| |
| |
| |
| |
| |
| |
| |
| | |
As written, this can never be true.
Spotted by the Sparse checker.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
Fix bug - Implement bfin ata interrupt handler to avoid "irq 68 nobody cared" (v2)
sata_mv: Improve naming of main_irq cause/mask identifiers
libata-scsi: improve rbuf handling for simulated commands
libata-scsi: clean up inquiry / mode sense related functions
[MIPS] ATA: Rename routerboard 500 to 532
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
cared" (v2)
Return IRQ_HANDLED when bfin ata device is busy.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3513
v1-v2:
- fold api breakage fixing patch together.
- mark 'static', not 'inline'.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Tidy up naming of things associated with the PCI / SOC chip
"main irq cause/mask" registers, as inspired by Jeff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Buffer length handling in simulated commands is error-prone and full
of bugs. There are a number of places where necessary length checks
are missing and if the output buffer is passed in as sglist, nothing
works.
This patch adds a static buffer ata_scsi_rbuf which is sufficiently
large to handle the larges output from simulated commands (4k
currently), let all simulte functions write to the buffer and removes
all length checks as we know that there always is enough buffer space.
Copying in (for ATAPI inquiry fix up) and out are handled by
sg_copy_to/from_buffer() behind ata_scsi_rbuf_get/put() interface
which handles sglist properly.
This patch is inspired from buffer length check fix patch from Petr
Vandrovec.
Updated to use sg_copy_to/from_buffer() as suggested by FUJITA
Tomonori.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
* make ata_scsiop_*() static
* make ata_scsi_set_sense() static and move it above its users
* make ata_scsi_rbuf_fill() static
* kill unused ata_scsi_badcmd()
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
| | |/
| |
| |
| |
| |
| |
| |
| | |
The platform is actually named routerboard 532 so let's call it this. This
patch only rename files, Kconfig and C symbols; no functional changes.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci:
x86: add pci=check_enable_amd_mmconf and dmi check
x86: work around io allocation overlap of HT links
acpi: get boot_cpu_id as early for k8_scan_nodes
x86_64: don't need set default res if only have one root bus
x86: double check the multi root bus with fam10h mmconf
x86: multi pci root bus with different io resource range, on 64-bit
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: get mp_bus_to_node early
x86 pci: remove checking type for mmconfig probe
x86: remove unneeded check in mmconf reject
driver core: try parent numa_node at first before using default
x86: seperate mmconf for fam10h out from setup_64.c
x86: if acpi=off, force setting the mmconf for fam10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86: mmconf enable mcfg early
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: validate against acpi motherboard resources
Fixed up fairly trivial conflicts in arch/x86/pci/{init.c,pci.h} due to
OLPC support manually.
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
so will disable that feature by default, and only enable that via
pci=check_enable_amd_mmconf or for system match with dmi table.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
normally BIOSes assign io/mmio range to different HT links without
overlapping, even same node same link should get non overlapping
entries.
but Rafael L. Wysocki's buggy BIOS creates a link with overlapping
entries for mmio and io:
node 0 link 0: io port [1000, ffffff]
node 0 link 0: mmio [e0000000, efffffff]
node 0 link 0: mmio [a0000, bffff]
node 0 link 0: mmio [80000000, ffffffff]
try to merge them and we will get:
bus: [00, ff] on node 0 link 0
bus: 00 index 0 io port: [0, ffff]
bus: 00 index 1 mmio: [80000000, fcffffffff]
bus: 00 index 2 mmio: [a0000, bffff]
so later we will reduce the chance to assign used resource to
unassigned device.
Reported-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
[mingo@elte.hu: split from "x86_64: get boot_cpu_id as early for k8_scan_nodes]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
if there's only one root bus there's no need to split resources.
This patch fixes the issue described at:
http://lkml.org/lkml/2008/4/10/304
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
some bioses give same range to mmconf for fam10h msr, and mmio for node/link.
fam10h msr will overide mmio for node/link.
so we can not assign range to devices under node/link for unassigned resources.
this patch will take range out from the mmio for node/link
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
... so we use the same code with Quad core cpu as old opteron.
This patch is useful when acpi=off or _PXM is not there in DSDT.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Currently, on an amd k8 system with multi ht chains, the numa_node of
pci devices under /sys/devices/pci0000:80/* is always 0, even if that
chain is on node 1 or 2 or 3.
Workaround: pcibus_to_node(bus) is used when we want to get the node that
pci_device is on.
In struct device, we already have numa_node member, and we could use
dev_to_node()/set_dev_node() to get and set numa_node in the device.
set_dev_node is called in pci_device_add() with pcibus_to_node(bus),
and pcibus_to_node uses bus->sysdata for nodeid.
The problem is when pci_add_device is called, bus->sysdata is not assigned
correct nodeid yet. The result is that numa_node will always be 0.
pcibios_scan_root and pci_scan_root could take sysdata. So we need to get
mp_bus_to_node mapping before these two are called, and thus
get_mp_bus_to_node could get correct node for sysdata in root bus.
In scanning of the root bus, all child busses will take parent bus sysdata.
So all pci_device->dev.numa_node will be assigned correctly and automatically.
Later we could use dev_to_node(&pci_dev->dev) to get numa_node, and we
could also could make other bus specific device get the correct numa_node
too.
This is an updated version of pci_sysdata and Jeff's pci_domain patch.
[ mingo@elte.hu: build fix ]
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
doesn't need to check if it is type1 or type2, we can use raw_pci_ops
directly.
also make pci_direct_conf1 static again.
anyway is there system with type 2 and mmconf support?
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
mmconfig is only used to access extended configuration space.
so don't need to reject MFG that only have one entry and only handle bus0.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
in the device_add, we try to use use parent numa_node.
need to make sure pci root bus's bridge device numa_node is set.
then we could use device->numa_node direclty for all device.
and don't need to call pcibus_to_node().
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Separate mmconf for fam10h out from setup_64.c
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
some BIOS only let AMD fam 10h handle bus0, and nvidia mcp55/ck804
to handle other buses. at that case MCFG will cover all over them.
but with acpi=off, we can not use MCFG. this patch will double check
the busnbits, and if it is less handling 256 bues, and acpi=off
will forcely reset the mmconf in msr, so we still use mmconf in above case.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
so even booting kernel with acpi=off or even MCFG is not there, we still can
use MMCONFIG.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
So we can use MMCONF when MMCONF is not set by BIOS
using TOP_MEM2 msr to get memory top, and try to scan fam10h mmio routing to
make sure the range is not conflicted with some prefetch MMIO that is above 4G.
(current only LinuxBIOS assign 64 bit mmio above 4G for some co-processor)
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Patch
"x86: validate against ACPI motherboard resources"
changed the mmconf init sequence, and init MMCONF late in acpi_init.
here change it back to old sequence:
1. check hostbridge in early
2. check MCFG with e820 in early
3. if all fail, will check MCFg with acpi _CRS in acpi_init
So we can make MCONF working again when acpi=off is set if hostbridge
support that.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
For x86_64, need to free pci_mmcfg_virt, and iounmap some pointers
when MMCONF is not reserved in E820 or acpi _CRS and get rejected.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Greg KH <greg@kroah.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This path adds validation of the MMCONFIG table against the ACPI reserved
motherboard resources. If the MMCONFIG table is found to be reserved in
ACPI, we don't bother checking the E820 table. The PCI Express firmware
spec apparently tells BIOS developers that reservation in ACPI is required
and E820 reservation is optional, so checking against ACPI first makes
sense. Many BIOSes don't reserve the MMCONFIG region in E820 even though
it is perfectly functional, the existing check needlessly disables MMCONFIG
in these cases.
In order to do this, MMCONFIG setup has been split into two phases. If PCI
configuration type 1 is not available then MMCONFIG is enabled early as
before. Otherwise, it is enabled later after the ACPI interpreter is
enabled, since we need to be able to execute control methods in order to
check the ACPI reserved resources. Presently this is just triggered off
the end of ACPI interpreter initialization.
There are a few other behavioral changes here:
- Validate all MMCONFIG configurations provided, not just the first one.
- Validate the entire required length of each configuration according to
the provided ending bus number is reserved, not just the minimum required
allocation.
- Validate that the area is reserved even if we read it from the chipset
directly and not from the MCFG table. This catches the case where the
BIOS didn't set the location properly in the chipset and has mapped it
over other things it shouldn't have.
This also cleans up the MMCONFIG initialization functions so that they
simply do nothing if MMCONFIG is not compiled in.
Based on an original patch by Rajesh Shah from Intel.
[akpm@linux-foundation.org: many fixes and cleanups]
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andi Kleen <ak@suse.de>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[RAPIDIO] Change RapidIO doorbell source and target ID field to 16-bit
[RAPIDIO] Add RapidIO connection info print out and re-training for broken connections
[RAPIDIO] Add serial RapidIO controller support, which includes MPC8548, MPC8641
[RAPIDIO] Add RapidIO node probing into MPC86xx_HPCN board id table
[RAPIDIO] Add RapidIO node into MPC8641HPCN dts file
[RAPIDIO] Auto-probe the RapidIO system size
[RAPIDIO] Add OF-tree support to RapidIO controller driver
[RAPIDIO] Add RapidIO multi mport support
[RAPIDIO] Move include/asm-ppc/rio.h to asm-powerpc
[RAPIDIO] Add RapidIO option to kernel configuration
[RAPIDIO] Change RIO function mpc85xx_ to fsl_
[POWERPC] Provide walk_memory_resource() for powerpc
[POWERPC] Update lmb data structures for hotplug memory add/remove
[POWERPC] Hotplug memory remove notifications for powerpc
[POWERPC] windfarm: Add PowerMac 12,1 support
[POWERPC] Fix building of pmac32 when CONFIG_NVRAM=m
[POWERPC] Add IRQSTACKS support on ppc32
[POWERPC] Use __always_inline for xchg* and cmpxchg*
[POWERPC] Add fast little-endian switch system call
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Change RapidIO doorbell source and target ID field to 16-bit for
support large system size, which max rio devid is 65535.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
connections
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This adds properties describing the RapidIO controller to the
device-tree source for the MPC8641HPCN board.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This initializes the RapidIO controller driver using addresses and
interrupt numbers obtained from the firmware device tree, rather than
using hardcoded constants.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The original RapidIO driver suppose there is only one mpc85xx RIO controller
in system. So, some data structures are defined as mpc85xx_rio global, such
as 'regs_win', 'dbell_ring', 'msg_tx_ring'. Now, I changed them to mport's
private members. And you can define multi RIO OF-nodes in dts file for multi
RapidIO controller in one processor, such as PCI/PCI-Ex host controllers in
Freescale's silicon. And the mport operation function declaration should be
changed to know which RapidIO controller is target.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
