aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* Update feature removal of obsolete raw1394 ISO requests.Ben Collins2006-06-12
| | | | | Signed-off-by: Jody McIntyre <scjody@modernduck.com> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* sbp2: fix S800 transfers if phys_dma is offBen Collins2006-06-12
| | | | | | | | | If sbp2 is forced to move data via ARM handler, the maximum packet size allowed for S800 transfers exceeds ohci1394's buffer size on platforms where PAGE_SIZE is 4096. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* sbp2: remove ohci1394 specific constantBen Collins2006-06-12
| | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ohci1394: make phys_dma parameter read-onlyBen Collins2006-06-12
| | | | | | | | | Being able to switch physical DMA on and off at run time would be a nice feature but a PITA to support by highlevel drivers and userspace apps. Therefore allow it only to be set when the driver is being loaded. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ohci1394: set address range propertiesBen Collins2006-06-12
| | | | | | | | | | | | | | | | | | | | | | | This patch supplies the API extension introduced by patch "ieee1394: extend lowlevel API for address range properties" with proper addresses. Like in patch ''ohci1394, sbp2: fix "scsi_add_device failed" with PL-3507 based devices'', 1 TeraByte is chosen as physical upper bound. This leaves a window for the middle address range. This choice is only relevant for adapters which actually have a programmable pysical upper bound register. (Only ALi and Fujitsu adapters are known for this. Most adapters have a fixed bound at 4 GB.) The middle address range is suitable for posted writes. AFAIK, PCILynx does not support physical DMA nor posted writes, therefore no equivalent change in the pcilynx driver is necessary. There is also a driver for GP2Lynx, although not in mainline Linux. I assume this hardware does not support these OHCI features either. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ieee1394: extend lowlevel API for address range propertiesBen Collins2006-06-12
| | | | | | | | | | | | | Host adapter hardware imposes certain restrictions and features on address ranges. Instead of hard-wire such ranges into the ieee1394 core or even into protocol drivers, let lowlevel drivers specify these ranges via struct hpsb_host. Patch "ohci1394: set address range properties" must be applied too, else hpsb_allocate_and_register_addrspace() won't work properly. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* sbp2: log number of supported concurrent loginsBen Collins2006-06-12
| | | | | | | | | | | Since this is useful information, promote it from a debug macro to a regular log message. The message appears only if the user set exclusive_login=0, therefore won't clutter the logs in normal use. Also update the comment on exclusive_login. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@modernduck.com> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* sbp2: remove manipulation of inquiry responseBen Collins2006-06-12
| | | | | | | | | | | | | | This code became ineffective a few Linux releases ago and is not required anyway. Note from Christoph Hellwig: scsi_cmnd.request_buffer is always a scatterlist these days. Checking random bites into it and then mangling the data in sbp2_check_sbp2_response will cause really bad memory corruption when you're not lucky enough to have the check not trigger by luck. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ieee1394: save RAM by using a single tlabel for broadcast transactionsBen Collins2006-06-12
| | | | | | | | | | Since broadcast transactions are already complete when the request has been sent, the same transaction label can be reused all over again, see IEEE 1394 7.3.2.5 and 6.2.4.3. Therefore we can reduce the footprint of struct hpsb_host by the size of one struct hpsb_tlabel_pool. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ieee1394: support for slow links or slow 1394b phy portsBen Collins2006-06-12
| | | | | | | | | | | | | | | | | | | | | | | | Add support for the following types of hardware: + nodes that have a link speed < PHY speed + 1394b PHYs that are less than S800 capable + 1394b/1394a adapter cable between two 1394b PHYs Also, S1600 and S3200 are now supported if IEEE1394_SPEED_MAX is raised. A probing function is added to nodemgr's config ROM fetching routine which adjusts the allowable speed if an access problem was encountered. Pros and Cons of the approach: + minimum code footprint to support this less widely used hardware + nearly no overhead for unaffected hardware - ineffective before nodemgr began to read the ROM of affected nodes - ineffective if ieee1394 is loaded with disable_nodemgr=1 The speed map CSRs which are published to the bus are not touched by the patch. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: Hakan Ardo <hakan@debian.org> Cc: Calculex <linux@calculex.com> Cc: Robert J. Kosinski <robk@cmcherald.com> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ieee1394/ohci1394: CycleTooLong interrupt managementBen Collins2006-06-12
| | | | | | | | | | | | | | | This patch modifies the ohci1394.c file to enable and manage the "cycle too long" interrupt. If this interrupt occurs, the "LinkControl.CycleMaster" bit of the host controller is reseted. This implies, that the host controller does not send "cycle start" packet anymore freezing then the isochronous communication. The management of the interrupt added by the patch is that when the interrupt occurs, the OHCI irq handler prints a kernel log warning and then sets the "LinkControl.CycleMaster" bit again resuming the isochronous communication. Signed-off-by: Jean-Baptiste Mur <jeanbaptiste@maunakeatech.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* raw1394: fix whitespace after x86_64 compat patchBen Collins2006-06-12
| | | | | Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* From: Arjan van de Ven <arjan@infradead.org>Ben Collins2006-06-12
| | | | | | | | | | | | | | Semaphore to mutex conversion. The conversion was generated via scripts, and the result was validated automatically via a script as well. Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Ben Collins <bcollins@debian.org> Cc: Jody McIntyre <scjody@modernduck.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* sbp2: make TSB42AA9 workaround specific to Momobay CX-1Ben Collins2006-06-12
| | | | | | | | | The workarounds are not required for DViCO Momobay FX-3A and AFAIR not for Momobay CX-2. These contain an TSB42AA9A but feature the same firmware_revision value as the older DViCO Momobay CX-1. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ohci1394: Remove superfluous call to free_dma_rcv_ctx,Ben Collins2006-06-12
| | | | | | | spotted by Adrian Bunk. Also remove some superfluous comments. Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* ieee1394: speed up of dma_region_sync_for_cpuBen Collins2006-06-12
| | | | | | | | when attempting to find the 'last' part of the dma region continue the search from where we left off, instead of starting the search over. Signed-off-by: Jim Westfall <jwestfall@surrealistic.net> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* video1394: be quietBen Collins2006-06-12
| | | | | | | | | | When working with multiple cameras and intensive applications, our logs get flooded with video1394 information which isn't of much interest. Any objections to demoting these messages to debug messages? Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
* Merge branch 'upstream-linus' of ↵Linus Torvalds2006-06-12
|\ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: [PATCH] sata_mv: grab host lock inside eng_timeout
| * [PATCH] sata_mv: grab host lock inside eng_timeoutMark Lord2006-06-11
| | | | | | | | | | | | | | | | | | | | | | Bug fix: mv_eng_timeout() calls mv_err_intr() without first grabbing the host lock, which can lead to all sorts of interesting scenarios. This whole error-handling portion of sata_mv is nasty (and will get fixed for the new EH stuff), but for now this patch will help keep it on life-support. Signed-off-by: Mark Lord <liml@rtr.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | [PATCH] Fix for the PPTP hangs that have been reportedPaul Mackerras2006-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | People have been reporting that PPP connections over ptys, such as used with PPTP, will hang randomly when transferring large amounts of data, for instance in http://bugzilla.kernel.org/show_bug.cgi?id=6530. I have managed to reproduce the problem, and the patch below fixes the actual cause. The problem is not in fact in ppp_async.c but in n_tty.c. What happens is that when pptp reads from the pty, we call read_chan() in drivers/char/n_tty.c on the master side of the pty. That copies all the characters out of its buffer to userspace and then calls check_unthrottle(), which calls the pty unthrottle routine, which calls tty_wakeup on the slave side, which calls ppp_asynctty_wakeup, which calls tasklet_schedule. So far so good. Since we are in process context, the tasklet runs immediately and calls ppp_async_process(), which calls ppp_async_push, which calls the tty->driver->write function to send some more output. However, tty->driver->write() returns zero, because the master tty->receive_room is still zero. We haven't returned from check_unthrottle() yet, and read_chan() only updates tty->receive_room _after_ calling check_unthrottle. That means that the driver->write call in ppp_async_process() returns 0. That would be fine if we were going to get a subsequent wakeup call, but we aren't (we just had it, and the buffer is now empty). The solution is for n_tty.c to update tty->receive_room _before_ calling the driver unthrottle routine. The patch below does this. With this patch I was able to transfer a 900MB file over a PPTP connection (taking about 25 minutes), whereas without the patch the connection would always stall in under a minute. Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6Linus Torvalds2006-06-11
|\ \ | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: [PATCH] PCI: reverse pci config space restore order [PATCH] PCI: Improve PCI config space writeback [PATCH] PCI: Error handling on PCI device resume [PATCH] PCI: fix pciehp compile issue when CONFIG_ACPI is not enabled
| * | [PATCH] PCI: reverse pci config space restore orderYu, Luming2006-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to Intel ICH spec, there are several rules that Base Address should be programmed before IOSE (PCICMD register ) enabled. For example ICH7: 12.1.3 SATA : the base address register for the bus master register should be programmed before this bit is set. 11.1.3: PCICMD (USB): The base address register for USB should be programmed before this bit is set. .... To make sure kernel code follow this rule , and prevent unnecessary confusion. I proposal this patch. Signed-off-by: Luming Yu <luming.yu@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * | [PATCH] PCI: Improve PCI config space writebackDave Jones2006-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At least one laptop blew up on resume from suspend with a black screen due to a lack of this patch. By only writing back config space that is different, we minimise the possibility of accidents like this. Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * | [PATCH] PCI: Error handling on PCI device resumeJean Delvare2006-06-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently don't handle errors properly when resuming a PCI device: * In pci_default_resume() we capture the error code returned by pci_enable_device() but don't pass it up to the caller. Introduced by commit 95a629657dbe28e44a312c47815b3dc3f1ce0970 * In pci_resume_device(), the errors possibly returned by the driver's .resume method or by the generic pci_default_resume() function are ignored. This patch fixes both issues. Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * | [PATCH] PCI: fix pciehp compile issue when CONFIG_ACPI is not enabledakpm@osdl.org2006-06-11
| |/ | | | | | | | | | | | | | | Fix build error when CONFIG_ACPI not defined Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* / [PATCH] typo in vmscan.cChristoph Lameter2006-06-11
|/ | | | | | | | | | | From: Christoph Lameter <clameter@sgi.com> Looks like a comma was left from the conversion from a struct to an assignment. Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [SPARC]: Migration cost tune up in sparc smp.Krzysztof Helt2006-06-11
| | | | | | | | | This patch sets the max_cache_size value required to tune up scheduler in SMP systems. Otherwise, the calculated migration_cost is too high and task scheduling may lock up. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* [SPARC64]: Set appropriate max_cache_size.David S. Miller2006-06-11
| | | | Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds2006-06-10
|\ | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: [SPARC64]: Avoid JBUS errors on some Niagara systems. [FUSION]: Fix mptspi.c build with CONFIG_PM not set. [TG3]: Handle Sun onboard tg3 chips more correctly. [SPARC64]: Dump local cpu registers in sun4v_log_error()
| * [SPARC64]: Avoid JBUS errors on some Niagara systems.David S. Miller2006-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Doing PCI config space accesses to non-present PCI slots can result in fatal JBUS errors if the PCI config access hypervisor call is performed on cpus other than the boot cpu. PCI config space accesses to present PCI slots works just fine. Recursively traverse the OBP device tree under the PCI controller node and record all present device IDs into a small hash table. Avoid the hypervisor call for any PCI config space access attempt for a device not recorded in the hash table. Signed-off-by: David S. Miller <davem@davemloft.net>
| * [FUSION]: Fix mptspi.c build with CONFIG_PM not set.Tom "spot" Callaway2006-06-09
| | | | | | | | | | Signed-off-by: Tom "spot" Callaway <tcallawa@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * [TG3]: Handle Sun onboard tg3 chips more correctly.David S. Miller2006-06-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Get rid of all the SUN_570X logic and instead: 1) Make sure MEMARB_ENABLE is set when we probe the SRAM for config information. If that is off we will get timeouts. 2) Always try to sync with the firmware, if there is no firmware running do not treat it as an error and instead just report it the first time we notice this condition. 3) If there is no valid SRAM signature, assume the device is onboard by setting TG3_FLAG_EEPROM_WRITE_PROT. Update driver version and release date. With help from Michael Chan and Fabio Massimo Di Nitto. Signed-off-by: David S. Miller <davem@davemloft.net>
| * [SPARC64]: Dump local cpu registers in sun4v_log_error()David S. Miller2006-06-09
| | | | | | | | | | | | This makes the debugging information more usable. Signed-off-by: David S. Miller <davem@davemloft.net>
* | [PATCH] powerpc: console_initcall ordering issuesMilton Miller2006-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From: Milton Miller <miltonm@bga.com> The add_preferred_console call in rtas_console.c was not causing the console to be selected. It turns out that the add_preferred_console was being called after the hvc_console driver was registered. It only works when it is called before the console driver is registered. Reorder hvc_console.o after the hvc_console drivers to allow the selection during console_initcall processing. Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Anton Blanchard <anton@samba.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [PATCH] I2O: Bugfixes to get I2O working againMarkus Lidel2006-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From: Markus Lidel <Markus.Lidel@shadowconnect.com> - Fixed locking of struct i2o_exec_wait in Executive-OSM - Removed LCT Notify in i2o_exec_probe() which caused freeing memory and accessing freed memory during first enumeration of I2O devices - Added missing locking in i2o_exec_lct_notify() - removed put_device() of I2O controller in i2o_iop_remove() which caused the controller structure get freed to early - Fixed size of mempool in i2o_iop_alloc() - Fixed access to freed memory in i2o_msg_get() See http://bugzilla.kernel.org/show_bug.cgi?id=6561 Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [PATCH] powernow-k8 crash workaroundAndrew Morton2006-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From: Andrew Morton <akpm@osdl.org> Work around the oops reported in http://bugzilla.kernel.org/show_bug.cgi?id=6478. Thanks to Ralf Hildebrandt <ralf.hildebrandt@charite.de> for testing and reporting. Acked-by: Dave Jones <davej@codemonkey.org.uk> Cc: "Brown, Len" <len.brown@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | [PATCH] Further alterations for memory barrier documentDavid Howells2006-06-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From: David Howells <dhowells@redhat.com> Apply some alterations to the memory barrier document that I worked out with Paul McKenney of IBM, plus some of the alterations suggested by Alan Stern. The following changes were made: (*) One of the examples given for what can happen with overlapping memory barriers was wrong. (*) The description of general memory barriers said that a general barrier is a combination of a read barrier and a write barrier. This isn't entirely true: it implies both, but is more than a combination of both. (*) The first example in the "SMP Barrier Pairing" section was wrong: the loads around the read barrier need to touch the memory locations in the opposite order to the stores around the write barrier. (*) Added a note to make explicit that the loads should be in reverse order to the stores. (*) Adjusted the diagrams in the "Examples Of Memory Barrier Sequences" section to make them clearer. Added a couple of diagrams to make it more clear as to how it could go wrong without the barrier. (*) Added a section on memory speculation. (*) Dropped any references to memory allocation routines doing memory barriers. They may do sometimes, but it can't be relied on. This may be worthy of further documentation later. (*) Made the fact that a LOCK followed by an UNLOCK should not be considered a full memory barrier more explicit and gave an example. Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Paul E. McKenney <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | Merge branch 'merge' of ↵Linus Torvalds2006-06-10
|\ \ | |/ |/| | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [PATCH] powerpc: Fix cell blade detection [PATCH] powerpc: Fix call to ibm,client-architecture-support powerpc: Fix machine check problem on 32-bit kernels
| * [PATCH] powerpc: Fix cell blade detectionArnd Bergmann2006-06-08
| | | | | | | | | | | | | | | | | | | | The IBM Cell blade firmware might confuse the kernel to think it's a pSeries machine. This fixes it for now. With a bit of luck, the firmware will be updated to avoid that in the future but currently that patch is needed. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * [PATCH] powerpc: Fix call to ibm,client-architecture-supportBenjamin Herrenschmidt2006-06-08
| | | | | | | | | | | | | | | | | | | | | | | | The code in prom_init.c calling the firmware ibm,client-architecture-support method on pSeries has a bug where it fails to properly pass the instance handle of the firmware object when trying to call a method. Result ranges from the call doing nothing to the firmware crashing. (Found by Segher, thanks !) Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
| * powerpc: Fix machine check problem on 32-bit kernelsPaul Mackerras2006-06-08
| | | | | | | | | | | | | | | | | | This fixes a bug found by Dave Jones that means that it is possible for userspace to provoke a machine check on 32-bit kernels. This also fixes a couple of other places where I found similar problems by inspection. Signed-off-by: Paul Mackerras <paulus@samba.org>
* | Merge branch 'upstream-fixes' of ↵Linus Torvalds2006-06-08
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 * 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: e1000: remove risky prefetch on next_skb->data e1000: fix ethtool test irq alloc as "probe" [PATCH] bcm43xx: add DMA rx poll workaround to DMA4
| * \ Merge branch 'upstream-fixes' of ↵Jeff Garzik2006-06-08
| |\ \ | | | | | | | | | | | | git://lost.foo-projects.org/~ahkok/git/netdev-2.6 into upstream-fixes
| | * | e1000: remove risky prefetch on next_skb->dataAuke Kok2006-06-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It was brought to our attention that the prefetches break e1000 traffic on xscale/arm architectures. Remove them for now. We'll let them stay in mm for a while, or find a better solution to enable. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| | * | e1000: fix ethtool test irq alloc as "probe"Auke Kok2006-06-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | New code added in 2.6.17 caused setup_irq to print a warning when running ethtool -t eth0 offline. This test marks the request_irq call made by this test as a "probe" to see if the interrupt is shared or not. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
| * | | Merge branch 'upstream-fixes' of ↵Jeff Garzik2006-06-08
| |\ \ \ | | |_|/ | |/| | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes
| | * | [PATCH] bcm43xx: add DMA rx poll workaround to DMA4Michael Buesch2006-06-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also add the Poll RX DMA Memory workaround to the DMA4 (xmitstatus) path. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | | | [PATCH] s390: fix in-user atomic futex operation.Martin Schwidefsky2006-06-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | From: Martin Schwidefsky <schwidefsky@de.ibm.com> __futex_atomic_op needs to do an atomic operation in the user address space, not the kernel address space. Add the missing sacf 256/sacf 0 to switch to the secondary mode before doing the compare-and-swap. In addition add another fixup for catch specification exceptions if the compare-and-swap address is not aligned. Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | | [PATCH] debugfs inode leakJens Axboe2006-06-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Looking at the reiser4 crash, I found a leak in debugfs. In debugfs_mknod(), we create the inode before checking if the dentry already has one attached. We don't free it if that is the case. These bugs happen quite often, I'm starting to think we should disallow such coding in CodingStyle. Signed-off-by: Jens Axboe <axboe@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* | | | [PATCH] elevator switching raceJens Axboe2006-06-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There's a race between shutting down one io scheduler and firing up the next, in which a new io could enter and cause the io scheduler to be invoked with bad or NULL data. To fix this, we need to maintain the queue lock for a bit longer. Unfortunately we cannot do that, since the elevator init requires to be run without the lock held. This isn't easily fixable, without also changing the mempool API. So split the initialization into two parts, and alloc-init operation and an attach operation. Then we can preallocate the io scheduler and related structures, and run the attach inside the lock after we detach the old one. This patch has survived 30 minutes of 1 second io scheduler switching with a very busy io load. Signed-off-by: Jens Axboe <axboe@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
generated by cgit v1.2.2 (git 2.25.0) at 2024-09-23 04:32:56 -0400