aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* ath9k: call ath9k_set_tsfadjust from ath9k_beacon_configFelix Fietkau2013-12-19
| | | | | | | Make that function and ath9k_allow_beacon_config static Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: move ath9k_debug_sync_cause out of ath9k_hwFelix Fietkau2013-12-19
| | | | | | | ath9k_hw should not depend on any ath9k data structures like ath_softc Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* bcma: add missing put_device callLevente Kurusa2013-12-19
| | | | | | | This is required so that we give up the last reference to the device. Signed-off-by: Levente Kurusa <levex@linux.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Use a subroutine for the AR9330 reset WARSujith Manoharan2013-12-18
| | | | | Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix RTC reset delaySujith Manoharan2013-12-18
| | | | | | | | The delay that is required after issuing a RTC reset varies for each chip. Handle this properly. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Add a delay between RTC reset/clear for AR9003Sujith Manoharan2013-12-18
| | | | | | | | | The small delay that is present between a RTC reset/clear operation is required for the chip to settle and this is needed for all chips, not just the AR9002 family. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix regulatory complianceSujith Manoharan2013-12-18
| | | | | | | | | | | To comply with ETSI regulations, make sure that the CCA registers are programmed with the threshold values from the EEPROM/Caldata. A new field is used to indicate if the card has been calibrated with the required threshold information. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Update BaseExtension_1 eeprom structureSujith Manoharan2013-12-18
| | | | | | | | * Add a new field "misc_enable" * Use int_8 for tempslopextension. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Initialize "switchcomspdt" eeprom field explicitlySujith Manoharan2013-12-18
| | | | | Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Remove unneeded ref. count initializationSujith Manoharan2013-12-18
| | | | | | | | The interrupt reference counter is always initialized in ath9k_start(). Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup ath9k.hSujith Manoharan2013-12-18
| | | | | | | | * Remove unused macros. * Move definitions to appropriate sections. Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Cleanup spectral scan codeSujith Manoharan2013-12-18
| | | | | | | | * Move definitions to spectral.h * Move processing/debug code to spectral.c Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: update MAINTAINERSLuis R. Rodriguez2013-12-18
| | | | | | | I've thrown the towel at QCA. Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: properly preserve TSF across resetFelix Fietkau2013-12-18
| | | | | | | | | | | | | | | The beacon code previously reset TSF on every configuration call, as some of the code was not prepared to properly calculate nexttbtt based on current TSF. This patch adds a common function for calculating nexttbtt and moves the TSF reset to driver start. This should improve AP mode compatibility with various stations that expect the TSF to not randomly jump due to hardware resets. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: clean up station beacon timer APIFelix Fietkau2013-12-18
| | | | | | | | Remove unused fields, pass timer info in usec instead of TU. Preparation for fixing nexttbtt calculation Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove spur related unused definesFelix Fietkau2013-12-18
| | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove additional_swba_backoffFelix Fietkau2013-12-18
| | | | | | | It is unused Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: simplify spur channel handlingFelix Fietkau2013-12-18
| | | | | | | | Remove ah->config.spurmode and ah->config.spurchans, always use EEPROM data. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove ah->config.pcie_clock_reqFelix Fietkau2013-12-18
| | | | | | | It is unused Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: remove defunct ad-hoc mode ATIM window handling codeFelix Fietkau2013-12-18
| | | | | | | | | The hardware does not have support for ATIM processing, and the driver does not set up ah->atim_window anywhere. Additionally, the code can clobber the timer used by P2P powersave. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: clean up generic timer codeFelix Fietkau2013-12-18
| | | | | | | | | | - Use generic bitops instead of custom hackery - Move interrupt enable/disable logic from ath9k to ath9k_hw - Decouple ISR call from btcoex - Make the overflow callback optional (to prevent IRQ storms) Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_hw: use a software timer for btcoex no_stomp_timerFelix Fietkau2013-12-18
| | | | | | | | TSF accuracy is not needed here, and there is only one usable generic timer that is supported by all chips and uses the primary TSF counter. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: add support for reporting per-chain signal strengthFelix Fietkau2013-12-18
| | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_common: get rid of an unnecessary variableFelix Fietkau2013-12-18
| | | | | | | There's no need to truncate curchan->hw_value to u8 Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* drivers: net: Mark functions as static in debug.cRashika Kheria2013-12-18
| | | | | | | | | | | | | | This patch marks the function il_clear_traffic_stats() in debug.c as static because they are not used outside this file. Thus, it also removes the following warnings in wireless/iwlegacy/debug.c: drivers/net/wireless/iwlegacy/debug.c:35:1: warning: no previous prototype for ‘il_clear_traffic_stats’ [-Wmissing-prototypes] Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* drivers: net: Mark functions as static in 4965-debug.cRashika Kheria2013-12-18
| | | | | | | | | | | | | | | | | This patch marks the function il4965_ucode_rx_stats_read(), il4965_ucode_tx_stats_read() and il4965_ucode_general_stats_read() in 4965-debug.c as static because they are not used outside this file. Thus, it also removes the following warnings in wireless/iwlegacy/4965-debug.c: drivers/net/wireless/iwlegacy/4965-debug.c:59:1: warning: no previous prototype for ‘il4965_ucode_rx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/4965-debug.c:471:1: warning: no previous prototype for ‘il4965_ucode_tx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/4965-debug.c:637:1: warning: no previous prototype for ‘il4965_ucode_general_stats_read’ [-Wmissing-prototypes] Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* drivers: net: Mark functions as static in 3945-debug.cRashika Kheria2013-12-18
| | | | | | | | | | | | | | | | | This patch marks the function il3945_ucode_rx_stats_read(), il3945_ucode_tx_stats_read() and il3945_ucode_general_stats_read() in 3945-debug.c as static because they are not used outside this file. Thus, it also removes the following warnings in wireless/iwlegacy/3945-debug.c: drivers/net/wireless/iwlegacy/3945-debug.c:52:1: warning: no previous prototype for ‘il3945_ucode_rx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/3945-debug.c:317:1: warning: no previous prototype for ‘il3945_ucode_tx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/3945-debug.c:407:1: warning: no previous prototype for ‘il3945_ucode_general_stats_read’ [-Wmissing-prototypes] Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: download per country tx power table to firmwareBing Zhao2013-12-18
| | | | | | | | | | | | | | When driver gets regulatory domain change notifications or before associates to an AP with Country IE, the txpwrlimit table stored in device tree for that country is downloaded to firmware. The txpwrlimit downloading will happen only at the first time when the alpha2 country code is changed. World regulatory domain "00" notification doesn't trigger the downloading. This behavior is same as domain_info command. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: download cal-data from device-tree to firmwareBing Zhao2013-12-18
| | | | | | | | | | Currently only conf file based cal-data downloading is supported. On embedded platforms a better place to store the cal-data is in device tree. Add cal-data downloading from device tree to firmware. Both methods can co-exist. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: remove cfg_data constructionBing Zhao2013-12-18
| | | | | | | | | The cfg_data buffer will include the cfg_data structure header (action, type, data_len). This makes it work for all data types without extra parsing. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mwifiex: send regulatory domain info to firmware only if alpha2 changedBing Zhao2013-12-18
| | | | | | | | | | | | On cfg80211 regulatory domain change, drivers gets alpha2 country code or "00" in driver's notification handler. In most cases, the pattern will be US, 00, US, 00, US, 00, US, ... There is no need to send domain info to firmware in case of "00" or with the same alpha2 country code. Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: fix 5/10MHz channel width initialization on ar9003Lorenzo Bianconi2013-12-18
| | | | | | | | | Move ath9k_hw_set_rfmode() after ath9k_hw_process_ini() in order to avoid AR_PHY_MODE register is overwritten with default values by ar9003_hw_process_ini() Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k_htc: reconfigure led_gpios after resumeOleksij Rempel2013-12-18
| | | | | | | | | On suspend/resume, firmware will restart and gpios configuration will be reseted. Restore this configureation at least for LEDs Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: clarify struct brcmf_sdio_dev::func[0] referenceArend van Spriel2013-12-18
| | | | | | | | | | | | | | | The struct brcmf_sdio_dev contains array of sdio functions that are used in the driver. However, during probe func[0] entry was assigned to the function 1 reference. This was corrected upon doing the actual I/O access. This patch makes it more clear by creating the func[0] entry properly and use it as is during I/O access. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove brcmf_sdio_disconnect() functionArend van Spriel2013-12-18
| | | | | | | | | | | Instead of calling brcmf_sdio_disconnect() expose brcmf_sdio_remove() and call it directly. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: use consistent function names in dhd_sdio.cArend van Spriel2013-12-18
| | | | | | | | | | | Functions in dhd_sdio.c that are called with struct brcmf_sdio instance are renamed consistently with brcmf_sdio_ prefix. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Combine protocol push hdr and bus txdata.Hante Meuleman2013-12-18
| | | | | | | | | | | | | | | | For the transmission of data a protocol push hdr is performed followed by a bus txdata call. For the new protocol msgbuf this is not workable. Since they are already "loosely" coupled for bcdc protocol they are combined. This means that txdata will go "through" the protocol layer and a seperate protocol push hdr will not be needed anymore. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Add definition of new protocol layer msgbuf.Hante Meuleman2013-12-18
| | | | | | | | | | | | | | A new protocol layer msgbuf will be added in the future. This change makes it possible to select the desired layer by the bus driver. USB and SDIO will select BCDC. At the moment nothing is being done with this information. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Fix hex dump for FWIL.Hante Meuleman2013-12-18
| | | | | | | | | | | | | The debug function brcmf_dbg_hex_dump API got changed and the information string should preferably contain a \n at the end of the string. Update the FWIL so debug output looks better. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: Move common BCDC code in single function.Hante Meuleman2013-12-18
| | | | | | | | | | | | | The BCDC functions query_dcmd and set_dcmd both create a msgbuf to be sent to dongle this code is very similar and for optimisation best put in a function. Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: reduce function parameters in sdio send/receive callsArend van Spriel2013-12-18
| | | | | | | | | | | | | The SDIO send and receive functions in bcmsdh.c are always called with the same parameters. For the driver there is no use-case to call them otherwise so remove those parameters from function prototypes. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: use consistent function names in bcmsdh.cArend van Spriel2013-12-18
| | | | | | | | | | | | | Functions in bcmsdh.c that are called with struct brcmf_sdio_dev instance are renamed consistently with brcmf_sdiod_ prefix. Also removing brcmf_sdioh_attach/detach() functions and merge it with brcmf_sdiod_probe/remove(). Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove brcmf_sdio_wdtimer_enable() functionArend van Spriel2013-12-18
| | | | | | | | | Instead of using the brcmf_sdio_wdtimer_enable() function call brcmf_sdbrcm_wd_timer() directly. Reviewed-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: get rid of some void pointer parametersArend van Spriel2013-12-18
| | | | | | | | | | | | In sdio code a couple of functions use a void pointer as argument type although it should be struct brcmf_sdio. Changing the functions to have proper type checking. Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove regs parameter from sdio probe functionsArend van Spriel2013-12-18
| | | | | | | | | | | | The chip recognition requires a base address that was provided to it during the probe. However, the address is a fixed define value so it is unnecessary to pass through the probe functions. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove brcmf_sdio_regrw_helper() from header fileArend van Spriel2013-12-18
| | | | | | | | | | | Make brcmf_sdio_regrw_helper() static removing its use outside of the bcmsdh.c source file. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: use sdio functions to enable/disable F2Arend van Spriel2013-12-18
| | | | | | | | | | | | Instead of catching CCCR_IOEx register in F0 write access to determine whether F2 state needs to change do it with direct call to sdio_[enable/disable]_func(). Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove unused struct brcmf_sdio_dev::func_cis_ptr attributeArend van Spriel2013-12-18
| | | | | | | | | | | | During the SDIO probe the func_cis_ptr attribute in struct brcmf_sdio_dev is being determined, but it is never used after that. Removing it also obsoletes two functions in bcmsdh.c. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: remove unnecessary function prototypesArend van Spriel2013-12-18
| | | | | | | | | | | | With the merge of bcmsdh.c and bcmsdh_mmc.c several function prototypes are no longer necessary and can be removed. Consequence is reordering some of the functions. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* brcmfmac: combine bcmsdh source files into oneArend van Spriel2013-12-18
| | | | | | | | | | | The driver has four files specific to SDIO host interface handling. This commit reduces that by merging two closely related source files. Reviewed-by: Franky Lin <frankyl@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-02-06 13:04:51 -0500