| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
Replace clk_enable() and clk_disable() calls with
clk_prepare_enable() and clk_disable_unprepare()
to get ready for the migration to the common clock
framework.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On some AR934x based systems, where the frequency of
the AHB bus is relatively high, the built-in watchdog
causes a spurious restart when it gets enabled.
The possible cause of these restarts is that the timeout
value written into the TIMER register does not reaches
the hardware in time.
Add an explicit delay into the ath79_wdt_enable function
to avoid the spurious restarts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: <stable@vger.kernel.org>
|
| |
|
|
|
|
|
|
|
| |
This patch removes platform_set_drvdata() which is not used in
the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
with the watchdog
Use the prescaler index, rather than its value, to configure the watchdog.
This will prevent a mismatch with the prescaler used to calculate the cycles.
Signed-off-by: Per Gundberg <per.gundberg@icomera.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
When compiling sunxi_defconfig while using C=2, the following error
causes the compilation to fail:
drivers/watchdog/sunxi_wdt.c:60:15: error: constant 0b0001 is not a valid number
Fix it by using hex notation instead of the non-standard binary one
Signed-off-by: Emilio Lopez <emilio@elopez.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exits.
This change was suggested by Thomas Gleixner.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,t,ex;
@@
struct t i = { .remove = ex, };
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
| |
|
|
|
|
|
|
|
|
| |
According to its Kconfig help text, the sbc8360 watchdog driver is
only used on the Axiomtek SBC8360 single-board computer. This piece of
hardware is 32-bit x86 so the driver is useless beyond X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p fixes from Eric Van Hensbergen:
"Two bug fixes, one in xattr error path and the other in parsing
major/minor numbers from devices"
* tag 'for-linus-3.16-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9P: fix return value in v9fs_fid_xattr_set
fs/9p: adjust sscanf parameters accordingly to the variable types
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
v9fs_fid_xattr_set is supposed to return 0 on success.
This corrects the behaviour introduced in commit
bdd5c28dcb8330b9074404cc92a0b83aae5606a
"9p: fix return value in case in v9fs_fid_xattr_set()"
(The function returns a negative error on error, as expected)
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This function is supposed to return true if the new load imbalance is
worse than the old one. It didn't. I can only hope brown paper bags
are in style.
Now things converge much better on both the 4 node and 8 node systems.
I am not sure why this did not seem to impact specjbb performance on the
4 node system, which is the system I have full-time access to.
This bug was introduced recently, with commit e63da03639cc ("sched/numa:
Allow task switch if load imbalance improves")
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
shrink_inactive_list() used to wait 0.1s to avoid congestion when all
the pages that were isolated from the inactive list were dirty but not
under active writeback. That makes no real sense, and apparently causes
major interactivity issues under some loads since 3.11.
The ostensible reason for it was to wait for kswapd to start writing
pages, but that seems questionable as well, since the congestion wait
code seems to trigger for kswapd itself as well. Also, the logic behind
delaying anything when we haven't actually started writeback is not
clear - it only delays actually starting that writeback.
We'll still trigger the congestion waiting if
(a) the process is kswapd, and we hit pages flagged for immediate
reclaim
(b) the process is not kswapd, and the zone backing dev writeback is
actually congested.
This probably needs to be revisited, but as it is this fixes a reported
regression.
Reported-by: Felipe Contreras <felipe.contreras@gmail.com>
Pinpointed-by: Hillf Danton <dhillf@gmail.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"Clean ups and miscellaneous bug fixes, in particular for the new
collapse_range and zero_range fallocate functions. In addition,
improve the scalability of adding and remove inodes from the orphan
list"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (25 commits)
ext4: handle symlink properly with inline_data
ext4: fix wrong assert in ext4_mb_normalize_request()
ext4: fix zeroing of page during writeback
ext4: remove unused local variable "stored" from ext4_readdir(...)
ext4: fix ZERO_RANGE test failure in data journalling
ext4: reduce contention on s_orphan_lock
ext4: use sbi in ext4_orphan_{add|del}()
ext4: use EXT_MAX_BLOCKS in ext4_es_can_be_merged()
ext4: add missing BUFFER_TRACE before ext4_journal_get_write_access
ext4: remove unnecessary double parentheses
ext4: do not destroy ext4_groupinfo_caches if ext4_mb_init() fails
ext4: make local functions static
ext4: fix block bitmap validation when bigalloc, ^flex_bg
ext4: fix block bitmap initialization under sparse_super2
ext4: find the group descriptors on a 1k-block bigalloc,meta_bg filesystem
ext4: avoid unneeded lookup when xattr name is invalid
ext4: fix data integrity sync in ordered mode
ext4: remove obsoleted check
ext4: add a new spinlock i_raw_lock to protect the ext4's raw inode
ext4: fix locking for O_APPEND writes
...
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This commit tries to fix a bug that we can't read symlink properly with
inline data feature when the length of symlink is greater than 60 bytes
but less than extra space.
The key issue is in ext4_inode_is_fast_symlink() that it doesn't check
whether or not an inode has inline data. When the user creates a new
symlink, an inode will be allocated with MAY_INLINE_DATA flag. Then
symlink will be stored in ->i_block and extended attribute space. In
the mean time, this inode is with inline data flag. After remounting
it, ext4_inode_is_fast_symlink() function thinks that this inode is a
fast symlink so that the data in ->i_block is copied to the user, and
the data in extra space is trimmed. In fact this inode should be as a
normal symlink.
The following script can hit this bug.
#!/bin/bash
cd ${MNT}
filename=ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrstuvwxyz0123456789
rm -rf test
mkdir test
cd test
echo "hello" >$filename
ln -s $filename symlinkfile
cd
sudo umount /mnt/sda1
sudo mount -t ext4 /dev/sda1 /mnt/sda1
readlink /mnt/sda1/test/symlinkfile
After applying this patch, it will break the assumption in e2fsck
because the original implementation doesn't want to support symlink
with inline data.
Reported-by: "Darrick J. Wong" <darrick.wong@oracle.com>
Reported-by: Ian Nartowicz <claws@nartowicz.co.uk>
Cc: Ian Nartowicz <claws@nartowicz.co.uk>
Cc: Tao Ma <tm@tao.ma>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The variable "size" is expressed as number of blocks and not as
number of clusters, this could trigger a kernel panic when using
ext4 with the size of a cluster different from the size of a block.
Cc: stable@vger.kernel.org
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Tail of a page straddling inode size must be zeroed when being written
out due to POSIX requirement that modifications of mmaped page beyond
inode size must not be written to the file. ext4_bio_write_page() did
this only for blocks fully beyond inode size but didn't properly zero
blocks partially beyond inode size. Fix this.
The problem has been uncovered by mmap_11-4 test in openposix test suite
(part of LTP).
Reported-by: Xiaoguang Wang <wangxg.fnst@cn.fujitsu.com>
Fixes: 5a0dc7365c240
Fixes: bd2d0210cf22f
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Remove local variable "stored" from ext4_readdir(...). This variable
gets initialized but is never used inside the function.
Signed-off-by: Giedrius Rekasius <giedrius.rekasius@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
xfstests generic/091 is failing when mounting ext4 with data=journal.
I think that this regression is same problem that occurred prior to collapse
range issue. So ZERO RANGE also need to call ext4_force_commit as
collapse range.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Shuffle code around in ext4_orphan_add() and ext4_orphan_del() so that
we avoid taking global s_orphan_lock in some cases and hold it for
shorter time in other cases.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Use sbi pointer consistently in ext4_orphan_del() instead of opencoding
it sometimes. Also ext4_orphan_add() uses EXT4_SB(sb) often so create
sbi variable for it as well and use it.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In ext4_es_can_be_merged() when checking whether we can merge two
extents we should use EXT_MAX_BLOCKS instead of defining it manually.
Also if it is really the case we should notify userspace because clearly
there is a bug in extent status tree implementation since this should
never happen.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Make them more consistently
Signed-off-by: xieliang <xieliang@xiaomi.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Caches from 'ext4_groupinfo_caches' may be in use by other mounts,
which have already existed. So, it is incorrect to destroy them when
newly requested mount fails.
Found by Linux File System Verification project (linuxtesting.org).
Signed-off-by: Andrey Tsyvarev <tsyvarev@ispras.ru>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
I have been running make namespacecheck to look for unneeded globals, and
found these in ext4.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
On a bigalloc,^flex_bg filesystem, the ext4_valid_block_bitmap
function fails to convert from blocks to clusters when spot-checking
the validity of the bitmap block that we've just read from disk. This
causes ext4 to think that the bitmap is garbage, which results in the
block group being taken offline when it's not necessary. Add in the
necessary EXT4_B2C() calls to perform the conversions.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The ext4_bg_has_super() function doesn't know about the new rules for
where backup superblocks go on a sparse_super2 filesystem. Therefore,
block bitmap initialization doesn't know that it shouldn't reserve
space for backups in groups that are never going to contain backups.
The result of this is e2fsck complaining about the block bitmap being
incorrect (fortunately not in a way that results in cross-linked
files), so fix the whole thing.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
On a filesystem with a 1k block size, the group descriptors live in
block 2, not block 1. If the filesystem has bigalloc,meta_bg set,
however, the calculation of the group descriptor table location does
not take this into account and returns the wrong block number. Fix
the calculation to return the correct value for this case.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In ext4_xattr_set_handle() we have checked the xattr name's length. So
we should also check it in ext4_xattr_get() to avoid unneeded lookup
caused by invalid name.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When we perform a data integrity sync we tag all the dirty pages with
PAGECACHE_TAG_TOWRITE at start of ext4_da_writepages. Later we check
for this tag in write_cache_pages_da and creates a struct
mpage_da_data containing contiguously indexed pages tagged with this
tag and sync these pages with a call to mpage_da_map_and_submit. This
process is done in while loop until all the PAGECACHE_TAG_TOWRITE
pages are synced. We also do journal start and stop in each iteration.
journal_stop could initiate journal commit which would call
ext4_writepage which in turn will call ext4_bio_write_page even for
delayed OR unwritten buffers. When ext4_bio_write_page is called for
such buffers, even though it does not sync them but it clears the
PAGECACHE_TAG_TOWRITE of the corresponding page and hence these pages
are also not synced by the currently running data integrity sync. We
will end up with dirty pages although sync is completed.
This could cause a potential data loss when the sync call is followed
by a truncate_pagecache call, which is exactly the case in
collapse_range. (It will cause generic/127 failure in xfstests)
To avoid this issue, we can use set_page_writeback_keepwrite instead of
set_page_writeback, which doesn't clear TOWRITE tag.
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
BH can not be NULL at this point, ext4_read_dirblock() always return
non null value, and we already have done all necessery checks.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
To avoid potential data races, use a spinlock which protects the raw
(on-disk) inode.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Al Viro pointed out that locking for O_APPEND writes was problematic,
since the location of the write isn't known until after we take the
i_mutex, which impacts the ext4_unaligned_aio() and s_bitmap_maxbytes
check.
For O_APPEND always assume that the write is unaligned so call
ext4_unwritten_wait(). And to solve the second problem, take the
i_mutex earlier before we start the s_bitmap_maxbytes check.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
This shouldn't change any logic flow; just delete duplicated code.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This commit doesn't actually change anything; it just moves code
around in preparation for some code simplification work.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Copy generic_file_aio_write() into ext4_file_write(). This is part of
a patch series which allows us to simplify ext4_file_write() and
ext4_file_dio_write(), by calling __generic_file_aio_write() directly.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Currently in ext4 there is quite a mess when it comes to naming
unwritten extents. Sometimes we call it uninitialized and sometimes we
refer to it as unwritten.
The right name for the extent which has been allocated but does not
contain any written data is _unwritten_. Other file systems are
using this name consistently, even the buffer head state refers to it as
unwritten. We need to fix this confusion in ext4.
This commit changes every reference to an uninitialized extent (meaning
allocated but unwritten) to unwritten extent. This includes comments,
function names and variable names. It even covers abbreviation of the
word uninitialized (such as uninit) and some misspellings.
This commit does not change any of the code paths at all. This has been
confirmed by comparing md5sums of the assembly code of each object file
after all the function names were stripped from it.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Currently EXT4_MAP_UNINIT is used in dioread_nolock case to mark the
cases where we're using dioread_nolock and we're writing into either
unallocated, or unwritten extent, because we need to make sure that
any DIO write into that inode will wait for the extent conversion.
However EXT4_MAP_UNINIT is not only entirely misleading name but also
unnecessary because we can check for EXT4_MAP_UNWRITTEN in the
dioread_nolock case instead.
This commit removes EXT4_MAP_UNINIT flag.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.linuxfoundation.org/llvmlinux/kernel
Pull LLVM patches from Behan Webster:
"Next set of patches to support compiling the kernel with clang.
They've been soaking in linux-next since the last merge window.
More still in the works for the next merge window..."
* tag 'llvmlinux-for-v3.16' of git://git.linuxfoundation.org/llvmlinux/kernel:
arm, unwind, LLVMLinux: Enable clang to be used for unwinding the stack
ARM: LLVMLinux: Change "extern inline" to "static inline" in glue-cache.h
all: LLVMLinux: Change DWARF flag to support gcc and clang
net: netfilter: LLVMLinux: vlais-netfilter
crypto: LLVMLinux: aligned-attribute.patch
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Patch to prevent warning of a buggy compiler when using clang and
the ARM_UNWIND option.
Clang defines (at least on the current trunk) GNUC, GNUC_MINOR, and
GNUC_PATCHLEVEL to 4, 2, and 1 respectively.
This version of GCC gets flagged as buggy, but it isn't actually an
issue with clang so the patch will do what it did before unless clang
is defined and then it will not report the GCC version as an issue.
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
With compilers which follow the C99 standard (like modern versions of gcc and
clang), "extern inline" does the wrong thing (emits code for an externally
linkable version of the inline function). "static inline" is the correct choice
instead.
Author: Behan Webster <behanw@converseincode.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Both gcc (well, actually gnu as) and clang support the "-Wa,-gdwarf-2" option
(though clang does not support "-Wa,--gdwarf-2"). Since these flags are equivalent
in meaning, this patch uses the one which is better supported across compilers.
Signed-off-by: Behan Webster <behanw@converseincode.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Replaced non-standard C use of Variable Length Arrays In Structs (VLAIS) in
xt_repldata.h with a C99 compliant flexible array member and then calculated
offsets to the other struct members. These other members aren't referenced by
name in this code, however this patch maintains the same memory layout and
padding as was previously accomplished using VLAIS.
Had the original structure been ordered differently, with the entries VLA at
the end, then it could have been a flexible member, and this patch would have
been a lot simpler. However since the data stored in this structure is
ultimately exported to userspace, the order of this structure can't be changed.
This patch makes no attempt to change the existing behavior, merely the way in
which the current layout is accomplished using standard C99 constructs. As such
the code can now be compiled with either gcc or clang.
This version of the patch removes the trailing alignment that the VLAIS
structure would allocate in order to simplify the patch.
Author: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Vinícius Tinti <viniciustinti@gmail.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
__attribute__((aligned)) applies the default alignment for the largest scalar
type for the target ABI. gcc allows it to be applied inline to a defined type.
Clang only allows it to be applied to a type definition (PR11071).
Making it into 2 lines makes it more readable and works with both compilers.
Author: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Behan Webster <behanw@converseincode.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 vdso build fix from Peter Anvin:
"This fixes building the vdso code on older Linux systems, and probably
some non-Linux systems"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use <tools/le_byteshift.h> for littleendian access
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
There are no standard functions for littleendian data (unlike
bigendian data.) Thus, use <tools/le_byteshift.h> to access
littleendian data members. Those are fairly inefficient, but it
doesn't matter for this purpose (and can be optimized later.) This
avoids portability problems.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/20140606140017.afb7f91142f66cb3dd13c186@linux-foundation.org
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
|
| | |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.linaro.org/people/mike.turquette/linux into next
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06a6 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The Allwinner sunxi mmc host uses dma in bus-master mode using a built-in
designware idmac controller, which is identical to the one found in the mmc-dw
hosts. However the rest of the host is not identical to mmc-dw, it deals with
sending stop commands in hardware which makes it significantly different
from the mmc-dw devices.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
[hdegoede@redhat.com: various cleanups and fixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Chris Ball <chris@printf.net>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Commit 99cbd064b0 ("clk: qcom: Support display RCG clocks") adds
a use of the __clk_round_rate in a clock provided that can be built
as a loadable module.
This exports the symbol to avoid the build error from compiling
the qcom clock as a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
