aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* sh: __copy_user function can corrupt the stack in case of exceptionStuart MENEFY2008-11-13
| | | | | | | | | | | | | | | | | | | | The __copy_user function can corrupt the stack in the case of a non-trivial length of data, and either of the first two move instructions cause an exception. This is because the fixup for these two instructions is mapped to the no_pop case, but these instructions execute after the stack is pushed. This change creates an explicit NO_POP exception mapping macro, and uses it for the two instructions executed in the trivial case where no stack pushes occur. More information at ST Linux bugzilla: https://bugzilla.stlinux.com/show_bug.cgi?id=4824 Signed-off-by: Dylan Reid <dylan_reid@bose.com> Signed-off-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Fixed the TMU0 reload value on resumeFrancesco VIRLINZI2008-11-13
| | | | | | | | | | | | | This patch fixes the TMU0 interrupt frequency on suspend/resume. During the resume the kernel reprograms the TMU0.ClockEvent mode but if the mode is periodic than the TMU0.TCOR is updated with a random wrong value without taking care latest valid saved value. There was no problem with No_HZ system where TMU0.TCOR isn't used. Signed-off-by: Francesco M. Virlinzi <francesco.virlinzi@st.com> Signed-off-by: Stuart Menefy <stuart.menefy@st.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Don't factor in PAGE_OFFSET for valid_phys_addr_range() check.Paul Mundt2008-11-13
| | | | Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: early printk port type fixMagnus Damm2008-11-13
| | | | | | | Add PORT_SCIF to unbreak the early printk code. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* i2c: fix i2c-sh_mobile rx underrunMagnus Damm2008-11-13
| | | | | | | Fix receive path underrun in i2c-sh_mobile driver. Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Provide a sane valid_phys_addr_range() to prevent TLB reset with PMB.Paul Mundt2008-11-11
| | | | | | | | | | | | | | | With the PMB enabled, only P1SEG and up are covered by the PMB mappings, meaning that situations where out-of-bounds physical addresses are read from will lead to TLB reset after the PMB miss, allowing for use cases like dd if=/dev/mem to reset the TLB. Fix this up to make sure the reference is between __MEMORY_START (phys) and __pa(high_memory). This is coherent across all variants of sh/sh64 with and without MMU, though the PMB bug itself is only applicable to SH-4A parts. Reported-by: Hideo Saito <saito@densan.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* usb: r8a66597-hcd: fix wrong data access in SuperH on-chip USBYoshihiro Shimoda2008-11-11
| | | | | | | | When I used SuperH on-chip USB, there was the problem that accessed r8a66597_root_hub which was not allocated. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* fix sci type for SH7723Yoshihiro Shimoda2008-11-11
| | | | | | | This patch changes sci type of SH7723 from PORT_SCI to PORT_SCIFA. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* serial: sh-sci: fix cannot work SH7723 SCIFAYoshihiro Shimoda2008-11-11
| | | | | | | | SH7723 has SCIFA. This module is similer SCI register map, but it has FIFO. So this patch adds new type(PORT_SCIFA) and change some type checking. Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* sh: Handle fixmap TLB eviction more coherently.Paul Mundt2008-11-10
| | | | | | | | | | | | | | | | | | There was a race in the kmap_coherent() implementation. While we guarded against preemption, there was nothing preventing eviction of the pre-faulted fixmap entry from the UTLB. Under certain workloads this would result in the fixmap entries used for cache colouring being evicted from the UTLB in the midst of a copy_page(). In addition to pre-faulting, we also make sure to preserve the PTEs in the kernel page table and introduce a cached PTE for kmap_coherent() usage. This follows a similar change on MIPS ("[MIPS] Fix aliasing bug in copy_to_user_page / copy_from_user_page"). Reported-by: Hideo Saito <saito@densan.co.jp> Reported-by: CHIKAMA Masaki <masaki.chikama@gmail.com> Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* Linux 2.6.28-rc4v2.6.28-rc4Linus Torvalds2008-11-09
|
* regression: disable timer peek-ahead for 2.6.28Arjan van de Ven2008-11-09
| | | | | | | | | | | It's showing up as regressions; disabling it very likely just papers over an underlying issue, but time is running out for 2.6.28, lets get back to this for 2.6.29 Fixes: #11826 and #11893 Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'master' of ↵Linus Torvalds2008-11-09
|\ | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes * 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes: kbuild: Fixup deb-pkg target to generate separate firmware deb
| * kbuild: Fixup deb-pkg target to generate separate firmware debJonathan McDowell2008-11-09
| | | | | | | | | | | | | | | | | | | | The below is a simplistic fix for "make deb-pkg"; it splits the firmware out to a linux-firmware-image package and adds an (unversioned) Suggests to the linux package for this firmware. Signed-Off-By: Jonathan McDowell <noodles@earth.li> Acked-by: Frans Pop <elendil@planet.nl> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* | Don't ask twice about not including staging driversLinus Torvalds2008-11-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The "Exclude staging drivers" question is there so that we don't build staging drivers for allyesconfig or allnoconfig settings, but it's very irritating when you've already said "no" to staging drivers earlier. There is absolutely no point in declining twice - once you've declined the staging drivers, you're done. So make the second question depend on the first question having been answered in the affirmative. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | Merge branch 'for-2.6.28' of git://linux-nfs.org/~bfields/linuxLinus Torvalds2008-11-09
|\ \ | | | | | | | | | | | | * 'for-2.6.28' of git://linux-nfs.org/~bfields/linux: Fix nfsd truncation of readdir results
| * | Fix nfsd truncation of readdir resultsDoug Nazar2008-11-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 8d7c4203 "nfsd: fix failure to set eof in readdir in some situations" introduced a bug: on a directory in an exported ext3 filesystem with dir_index unset, a READDIR will only return about 250 entries, even if the directory was larger. Bisected it back to this commit; reverting it fixes the problem. It turns out that in this case ext3 reads a block at a time, then returns from readdir, which means we can end up with buf.full==0 but with more entries in the directory still to be read. Before 8d7c4203 (but after c002a6c797 "Optimise NFS readdir hack slightly"), this would cause us to return the READDIR result immediately, but with the eof bit unset. That could cause a performance regression (because the client would need more roundtrips to the server to read the whole directory), but no loss in correctness, since the cleared eof bit caused the client to send another readdir. After 8d7c4203, the setting of the eof bit made this a correctness problem. So, move nfserr_eof into the loop and remove the buf.full check so that we loop until buf.used==0. The following seems to do the right thing and reduces the network traffic since we don't return a READDIR result until the buffer is full. Tested on an empty directory & large directory; eof is properly sent and there are no more short buffers. Signed-off-by: Doug Nazar <nazard@dragoninc.ca> Cc: David Woodhouse <David.Woodhouse@intel.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
* | | Merge branch 'cpus4096' of ↵Linus Torvalds2008-11-09
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'cpus4096' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: cpumask: introduce new API, without changing anything, v3 cpumask: new API, v2 cpumask: introduce new API, without changing anything
| * | | cpumask: introduce new API, without changing anything, v3Rusty Russell2008-11-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Impact: cleanup Clean up based on feedback from Andrew Morton and others: - change to inline functions instead of macros - add __init to bootmem method - add a missing debug check Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Ingo Molnar <mingo@elte.hu>
| * | | cpumask: new API, v2Rusty Russell2008-11-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add cpumask_of() - add free_bootmem_cpumask_var() Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Ingo Molnar <mingo@elte.hu>
| * | | cpumask: introduce new API, without changing anythingRusty Russell2008-11-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Impact: introduce new APIs We want to deprecate cpumasks on the stack, as we are headed for gynormous numbers of CPUs. Eventually, we want to head towards an undefined 'struct cpumask' so they can never be declared on stack. 1) New cpumask functions which take pointers instead of copies. (cpus_* -> cpumask_*) 2) Several new helpers to reduce requirements for temporary cpumasks (cpumask_first_and, cpumask_next_and, cpumask_any_and) 3) Helpers for declaring cpumasks on or offstack for large NR_CPUS (cpumask_var_t, alloc_cpumask_var and free_cpumask_var) 4) 'struct cpumask' for explicitness and to mark new-style code. 5) Make iterator functions stop at nr_cpu_ids (a runtime constant), not NR_CPUS for time efficiency and for smaller dynamic allocations in future. 6) cpumask_copy() so we can allocate less than a full cpumask eventually (for alloc_cpumask_var), and so we can eliminate the 'struct cpumask' definition eventually. 7) work_on_cpu() helper for doing task on a CPU, rather than saving old cpumask for current thread and manipulating it. 8) smp_call_function_many() which is smp_call_function_mask() except taking a cpumask pointer. Note that this patch simply introduces the new functions and leaves the obsolescent ones in place. This is to simplify the transition patches. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Ingo Molnar <mingo@elte.hu>
* | | | net: unix: fix inflight counting bug in garbage collectorMiklos Szeredi2008-11-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously I assumed that the receive queues of candidates don't change during the GC. This is only half true, nothing can be received from the queues (see comment in unix_gc()), but buffers could be added through the other half of the socket pair, which may still have file descriptors referring to it. This can result in inc_inflight_move_tail() erronously increasing the "inflight" counter for a unix socket for which dec_inflight() wasn't previously called. This in turn can trigger the "BUG_ON(total_refs < inflight_refs)" in a later garbage collection run. Fix this by only manipulating the "inflight" counter for sockets which are candidates themselves. Duplicating the file references in unix_attach_fds() is also needed to prevent a socket becoming a candidate for GC while the skb that contains it is not yet queued. Reported-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk> Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> CC: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | clarify usage expectations for cnt32_to_63()Nicolas Pitre2008-11-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, all existing users of cnt32_to_63() are fine since the CPU architectures where it is used don't do read access reordering, and user mode preemption is disabled already. It is nevertheless a good idea to better elaborate usage requirements wrt preemption, and use an explicit memory barrier on SMP to avoid different CPUs accessing the counter value in the wrong order. On UP a simple compiler barrier is sufficient. Signed-off-by: Nicolas Pitre <nico@marvell.com> Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | Merge branch 'for-linus' of ↵Linus Torvalds2008-11-09
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: mmc: struct device - replace bus_id with dev_name(), dev_set_name() mmc: increase SD write timeout for crappy cards
| * | | | mmc: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers2008-11-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * | | | mmc: increase SD write timeout for crappy cardsPierre Ossman2008-11-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It seems that some cards are slightly out of spec and occasionally will not be able to complete a write in the alloted 250 ms [1]. Incease the timeout slightly to allow even these cards to function properly. [1] http://lkml.org/lkml/2008/9/23/390 Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* | | | | regulator: Use menuconfig in KconfigTakashi Iwai2008-11-09
|/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use menuconfig instead of flat configs so that you can disable/enable regulator items with one selection. Also, use depends instead of reverse selections to make life easier, too. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* | | | Merge branch 'sched-fixes-for-linus' of ↵Linus Torvalds2008-11-08
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: sched: optimize sched_clock() a bit sched: improve sched_clock() performance
| * | | | sched: optimize sched_clock() a bitIngo Molnar2008-11-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sched_clock() uses cycles_2_ns() needlessly - which is an irq-disabling variant of __cycles_2_ns(). Most of the time sched_clock() is called with irqs disabled already. The few places that call it with irqs enabled need to be updated. Signed-off-by: Ingo Molnar <mingo@elte.hu>
| * | | | sched: improve sched_clock() performanceIngo Molnar2008-11-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | in scheduler-intense workloads native_read_tsc() overhead accounts for 20% of the system overhead: 659567 system_call 41222.9375 686796 schedule 435.7843 718382 __switch_to 665.1685 823875 switch_mm 4526.7857 1883122 native_read_tsc 55385.9412 9761990 total 2.8468 this is large part due to the rdtsc_barrier() that is done before and after reading the TSC. But sched_clock() is not a precise clock in the GTOD sense, using such barriers is completely pointless. So remove the barriers and only use them in vget_cycles(). This improves lat_ctx performance by about 5%. Signed-off-by: Ingo Molnar <mingo@elte.hu>
* | | | | Merge branch 'oprofile-fixes-for-linus' of ↵Linus Torvalds2008-11-08
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'oprofile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: oprofile: Fix p6 counter overflow check Cell OProfile: Incorrect local array size in activate spu profiling function Revert "Cell OProfile: Incorrect local array size in activate spu profiling function" oprofile: fix memory ordering Cell OProfile: Incorrect local array size in activate spu profiling function Change UTF8 chars in Kconfig help text about Oprofile AMD barcelona
| * \ \ \ \ Merge branch 'oprofile-for-tip' of ↵Ingo Molnar2008-11-07
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile into x86/urgent
| | * | | | | oprofile: Fix p6 counter overflow checkAndi Kleen2008-11-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the counter overflow check for CPUs with counter width > 32 I had a similar change in a different patch that I didn't submit and I didn't notice the problem earlier because it was always tested together. Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Robert Richter <robert.richter@amd.com>
| | * | | | | Cell OProfile: Incorrect local array size in activate spu profiling functionCarl Love2008-10-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Updated the patch to address comments by Michael Ellerman. Specifically, changed upper limit in for loop to ARRAY_SIZE() macro and added a check to make sure the number of events specified by the user, which is used as the max for indexing various arrays, is no bigger then the declared size of the arrays. The size of the pm_signal_local array should be equal to the number of SPUs being configured in the array. Currently, the array is of size 4 (NR_PHYS_CTRS) but being indexed by a for loop from 0 to 7 (NUM_SPUS_PER_NODE). Signed-off-by: Carl Love <carll@us.ibm.com>
| | * | | | | Revert "Cell OProfile: Incorrect local array size in activate spu profiling ↵Robert Richter2008-10-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | function" This reverts commit fa448d6008cc81a3537e5db168fa0490e0caba68.
| | * | | | | oprofile: fix memory orderingNick Piggin2008-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Regular bitops don't work as locks on all architectures. Also: can use non-atomic unlock as no concurrent stores to the word. Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Robert Richter <robert.richter@amd.com>
| | * | | | | Cell OProfile: Incorrect local array size in activate spu profiling functionCarl Love2008-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The size of the pm_signal_local array should be equal to the number of SPUs being configured in the call. Currently, the array is of size 4 (NR_PHYS_CTRS) but being indexed by a for loop from 0 to 7 (NUM_SPUS_PER_NODE). Signed-off-by: Carl Love <carll@us.ibm.com> Signed-off-by: Robert Richter <robert.richter@amd.com>
| | * | | | | Change UTF8 chars in Kconfig help text about Oprofile AMD barcelonaJesper Dangaard Brouer2008-10-27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes screwing up text output when doing a make oldconfig and viewing help text of "OProfile AMD IBS support". When the terminal is not using an UTF8 locale / LANG. "make config" breaks terminal output and its not possible to continue. (Change added by changeset 852402cc Tue Jul 22 21:09:06 2008) Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: Robert Richter <robert.richter@amd.com>
* | | | | | | Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6Linus Torvalds2008-11-08
|\ \ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: Staging: make usbip depend on CONFIG_NET Staging: only build the tree if we really want to
| * | | | | | | Staging: make usbip depend on CONFIG_NETGreg Kroah-Hartman2008-11-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Thanks to Randy Dunlap for finding this problem. Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| * | | | | | | Staging: only build the tree if we really want toGreg Kroah-Hartman2008-11-08
| |/ / / / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This Kconfig change allows the common 'make allmodconfig' and 'make allyesconfig' build options to skip the staging tree, which is probably what you want to have happen anyway. This makes the linux-next developer's life a lot easier so he doesn't have to worry about changes that break the staging tree, that's for me to worry about... Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* / / / / / / Fix __pfn_to_page(pfn) for CONFIG_DISCONTIGMEM=yRafael J. Wysocki2008-11-08
|/ / / / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix the __pfn_to_page(pfn) macro so that it doesn't evaluate its argument twice in the CONFIG_DISCONTIGMEM=y case, because 'pfn' may be a result of a funtion call having side effects. For example, the hibernation code applies pfn_to_page(pfn) to the result of a function returning the pfn corresponding to the next set bit in a bitmap and the current bit position is modified on each call. This leads to "interesting" failures for CONFIG_DISCONTIGMEM=y due to the current behavior of __pfn_to_page(pfn). Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | | | | | Merge branch 'release' of ↵Linus Torvalds2008-11-07
|\ \ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6 * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6: [IA64] Reserve elfcorehdr memory in CONFIG_CRASH_DUMP [IA64] fix boot panic caused by offline CPUs [IA64] reorder Kconfig options to match x86 [IA64] Build VT-D iommu support into generic kernel [IA64] remove dead BIO_VMERGE_BOUNDARY definition [IA64] remove duplicated #include from pci-dma.c [IA64] use common header for software IO/TLB [IA64] fix the difference between node_mem_map and node_start_pfn [IA64] Add error_recovery_info field to SAL section header [IA64] Add UV watchlist support. [IA64] Simplify SGI uv vs. sn2 driver issues
| * | | | | | [IA64] Reserve elfcorehdr memory in CONFIG_CRASH_DUMPJay Lan2008-11-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | IA64 kdump kernel failed to initialize /proc/vmcore in 2.6.28-rc2. A bug was introduced in this patch commit: d9a9855d0b06ca6d6cc92596fedcc03f8512e062 always reserve elfcore header memory in crash kernel The problem was that the call to reserve_elfcorehdr() should be placed in CONFIG_CRASH_DUMP rather than in CONFIG_CRASH_KERNEL, which does not exist. Signed-off-by: Jay Lan <jlan@sgi.com> Acked-by: Simon Hormon <horms@verge.net.au> Signed-off-by: Tony Luck <tony.luck@intel.com>
| * | | | | | [IA64] fix boot panic caused by offline CPUsDoug Chapman2008-11-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes a regression introduced by 2c6e6db41f01b6b4eb98809350827c9678996698 "Minimize per_cpu reservations." That patch incorrectly used information about what CPUs are possible that was not yet initialized by ACPI. The end result was that per_cpu structures for offline CPUs were not initialized causing a NULL pointer reference. Since we cannot do the full acpi_boot_init() call any earlier, the simplest fix is to just parse the MADT for SAPIC entries early to find the CPU info. This should also allow for some cleanup of the code added by the "Minimize per_cpu reservations". This patch just fixes the regressions, the cleanup will come in a later patch. Signed-off-by: Doug Chapman <doug.chapman@hp.com> Signed-off-by: Alex Chiang <achiang@hp.com> CC: Robin Holt <holt@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
| * | | | | | [IA64] reorder Kconfig options to match x86Bjorn Helgaas2008-11-06
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | No functional change, just reorder some config options and update the "Power management and ACPI" label to match the defacto x86 standard. Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
| * | | | | | [IA64] Build VT-D iommu support into generic kernelTony Luck2008-11-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that all the ia64 mmu pieces are in the tree we can build support into the generic kernel. Signed-off-by: Tony Luck <tony.luck@intel.com>
| * | | | | | [IA64] remove dead BIO_VMERGE_BOUNDARY definitionFUJITA Tomonori2008-11-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The block layer dropped the virtual merge feature (b8b3e16cfe6435d961f6aaebcfd52a1ff2a988c5). BIO_VMERGE_BOUNDARY definition is meaningless now (For IA64, BIO_VMERGE_BOUNDARY has been meaningless for a long time since IA64 disables the virtual merge feature). Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Tony Luck <tony.luck@intel.com>
| * | | | | | [IA64] remove duplicated #include from pci-dma.cHuang Weiyi2008-11-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed duplicated #include <asm/machvec.h> and <linux/string.h> in arch/ia64/kernel/pci-dma.c. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
| * | | | | | [IA64] use common header for software IO/TLBJoerg Roedel2008-11-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the swiotlb prototypes from the architecture code and use the common header file instead. Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-01-17 19:54:32 -0500