aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* libata: clean up horkage handlingTejun Heo2007-07-10
| | | | | | | | | | | | | | | | | | | | Horkage handling had the following problems. * dev->horkage was positioned after ATA_DEVICE_CLEAR_OFFSET, so it was cleared before the device is configured. This broke HORKAGE_DIAGNOSTIC. * Some used dev->horkage while others called ata_device_blacklisted() directly. This was at best confusing. This patch moves dev->horkage right after dev->flags and set the field according to the blacklist during device configuration. All users test against dev->horkage. ata_device_blacklisted() now has only one user, make it static. While at it, rename it to ata_dev_blacklisted() for consistency. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: quirk IOMEGA ZIP 250 ATAPI FLOPPYTejun Heo2007-07-10
| | | | | | | | | | | The Zip 250 which chokes on MWDMA SET_XFERMODE sometimes have "Floppy" appeneded to its model number. Quirk it too. http://bugzilla.kernel.org/show_bug.cgi?id=8563 Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Hans de Bruin <bruinjm@xs4all.nl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata: simplify PCI legacy SFF host handlingTejun Heo2007-07-10
| | | | | | | | | | | | | | With PCI resource fix up for legacy hosts. We can use the same code path to allocate IO resources and initialize host for both legacy and native SFF hosts. Only IRQ requesting needs to be different. Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all legacy specific functions and use the renamed functions instead. This simplifies code a lot. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_mpc52xx: suspend/resume supportDomen Puncer2007-07-10
| | | | | | | | | Implement suspend and resume routines for mpc52xx ata driver. Tested on Lite5200b with deep-sleep and low-power (not yet in-tree) modes. Signed-off-by: Domen Puncer <domen.puncer@telargo.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* sata_promise: SATA hotplug support, take 2Mikael Pettersson2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables hotplugging of SATA devices in the sata_promise driver. It's been tested successfully on both first- and second-generation Promise SATA chips: SATA150 TX2plus, SATAII150 TX2plus, SATAII150 TX4, SATA300 TX2plus, and SATA300 TX4. The only quirk I've seen is that hotplugging (insertion) on the first-generation SATA150 TX2plus requires a lengthier EH sequence than on the second-generation chips. On the second-generation chips a simple soft reset seems to suffice, but on the first-generation chip there's a "port is slow to respond" after the initial soft reset, after which libata issues a hard reset, and then the device is recognised. The hotplug checks are high up in the interrupt handling path, not deep down in error_intr as in ahci/sata_sil24. That's because the chip doesn't signal hotplug status changes in the per-port status register: instead a global register contains hotplug control and status flags for all ports. I considered following the ahci/sata_sil24 structure, but that would have required non-trivial changes to the interrupt handling path, so I chose to keep the hotplug changes simple and unobtrusive. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> -- This patch depends on the "sata_promise: cleanups" patch. Changes since the previous version (posted June 19): - Correct pdc_interrupt() to increment 'handled' also in the hotplug case. This prevents IRQ_NONE from being returned when an interrupt only has hotplug events to handle, which could confuse the kernel's IRQ machinery. - Added testing on the SATAII150 TX4. drivers/ata/sata_promise.c | 41 ++++++++++++++++++++++++++++++++++++----- 1 files changed, 36 insertions(+), 5 deletions(-) Signed-off-by: Jeff Garzik <jeff@garzik.org>
* pata_sis: FIFO whackAlan Cox2007-07-10
| | | | | | | | | If you are using a SiS controller and the BIOS didn't set it up then the FIFO may be left active when we try and set up the CD. Not convinced this matters but I'd prefer to be safe Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* libata-core: convert to use cancel_rearming_delayed_work()Oleg Nesterov2007-07-10
| | | | | | | | | | We should not use cancel_work_sync(delayed_work->work). This works, but not good. We can use cancel_rearming_delayed_work(), this also simplifies the code. Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Merge branch 'for-linus' of ↵Linus Torvalds2007-07-10
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: mmc: at91_mci: fix hanging and rework to match flowcharts mmc: at91_mci typo sdhci: Fix "Unexpected interrupt" handling mmc: fix silly copy-and-paste error mmc: move layer init and workqueue to core file mmc: refactor host class handling mmc: refactor bus operations sdhci: add ene controller id mmc: bounce requests for simple hosts
| * mmc: at91_mci: fix hanging and rework to match flowchartsNicolas Ferre2007-07-09
| | | | | | | | | | | | | | | | | | | | | | | | Fixes hanging using multi block operations (seen during CMD25). Follows closely the datasheet flowcharts. This piece of code handles better big file writing. I had to take care of the notbusy signal during write (at91_mci_handle_cmdrdy function) and to rearrange the AT91_MCI_ENDRX and AT91_MCI_RXBUFF flag usage. Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * mmc: at91_mci typoNicolas Ferre2007-07-09
| | | | | | | | | | | | | | | | Typo fix in at91_mci driver : standardized the typo (at91_mci everywhere) Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * sdhci: Fix "Unexpected interrupt" handlingRolf Eike Beer2007-07-09
| | | | | | | | | | | | | | | | | | Whenever a power interrupt is signaled it is also reported as an unexpected one. All other unexpected interrupts get lost. Cause is a not inversed bitmask to remove power interrupts from the status. Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * mmc: fix silly copy-and-paste errorPierre Ossman2007-07-09
| | | | | | | | Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * mmc: move layer init and workqueue to core filePierre Ossman2007-07-09
| | | | | | | | Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * mmc: refactor host class handlingPierre Ossman2007-07-09
| | | | | | | | | | | | Move basic host class device handling to its own file for clarity. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * mmc: refactor bus operationsPierre Ossman2007-07-09
| | | | | | | | | | | | | | | | Move bus operations to its own file for the sake of clarity. Also delegate sysfs attributes to bus handlers in preparation for other more exotic types. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * sdhci: add ene controller idMilko Krachounov2007-07-09
| | | | | | | | | | | | | | | | | | ENE has a very weird design where an SDHCI device (0805) is presented on the PCI bus, but that device is non-functional, and the real device is hidden as a more generic device. Signed-off-by: Milko Krachounov <milko@3mhz.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
| * mmc: bounce requests for simple hostsPierre Ossman2007-07-09
| | | | | | | | | | | | | | | | Some hosts cannot do scatter/gather in hardware. Since not doing sg is such a big performance hit, we (optionally) bounce the requests to a simple linear buffer that we hand over to the driver. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* | Merge branch 'upstream-linus' of ↵Linus Torvalds2007-07-10
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (40 commits) bonding/bond_main.c: make 2 functions static ps3: gigabit ethernet driver for PS3, take3 [netdrvr] Fix dependencies for ax88796 ne2k clone driver eHEA: Capability flag for DLPAR support Remove sk98lin ethernet driver. sunhme.c:quattro_pci_find() must be __devinit bonding / ipv6: no addrconf for slaves separately from master atl1: remove write-only var in tx handler macmace: use "unsigned long flags;" Cleanup usbnet_probe() return value handling netxen: deinline and sparse fix eeprom_93cx6: shorten pulse timing to match spec (bis) phylib: Add Marvell 88E1112 phy id phylib: cleanup marvell.c a bit AX88796 network driver IOC3: Switch to pci refcounting safe APIs e100: Fix Tyan motherboard e100 not receiving IPMI commands QE Ethernet driver writes to wrong register to mask interrupts rrunner.c:rr_init() must be __devinit tokenring/3c359.c:xl_init() must be __devinit ...
| * | bonding/bond_main.c: make 2 functions staticAdrian Bunk2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Chad Tindel <ctindel@users.sourceforge.net> Cc: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | ps3: gigabit ethernet driver for PS3, take3Masakazu Mokuno2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hi, This is the third submission of the network driver for PS3. The differences from the previous one are: - renamed source file names so that their prefix can match with the module name - added cbe-oss-dev@ozlabs.org line for MAINTAINER file - changed some in copyright comments If there are no more comments, please apply for 2.6.23. Thank you -- Subject: PS3: Ethernet driver From: Masakazu Mokuno <mokuno@sm.sony.co.jp> Add Gigabit Ethernet support for the PS3 game console. The module will be called ps3_gelic. CC: Geoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | [netdrvr] Fix dependencies for ax88796 ne2k clone driverJeff Garzik2007-07-10
| | | | | | | | | | | | | | | | | | It needs writesb(), not available on all platforms. Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | eHEA: Capability flag for DLPAR supportJan-Bernd Themann2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch introduces a capability flag that is used by the DLPAR userspace tool to check which DLPAR features are supported by the eHEA driver. Missing goto has been included. Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | Remove sk98lin ethernet driver.Jeff Garzik2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | Unmaintained, superceded by skge. Prodded to deletion by Adrian Bunk. Acked by Stephen Hemminger. Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | sunhme.c:quattro_pci_find() must be __devinitAdrian Bunk2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following section mismatch: <-- snip --> ... MODPOST vmlinux WARNING: drivers/built-in.o(.text+0x272f8b): Section mismatch: reference to .init.text:quattro_pci_find (between 'happy_meal_pci_probe' and 'happy_meal_pci_remove') ... <-- snip --> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | bonding / ipv6: no addrconf for slaves separately from masterJay Vosburgh2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At present, when a device is enslaved to bonding, if ipv6 is active then addrconf will be initated on the slave (because it is closed then opened during the enslavement processing). This causes DAD and RS packets to be sent from the slave. These packets in turn can confuse switches that perform ipv6 snooping, causing them to incorrectly update their forwarding tables (if, e.g., the slave being added is an inactve backup that won't be used right away) and direct traffic away from the active slave to a backup slave (where the incoming packets will be dropped). This patch alters the behavior so that addrconf will only run on the master device itself. I believe this is logically correct, as it prevents slaves from having an IPv6 identity independent from the master. This is consistent with the IPv4 behavior for bonding. This is accomplished by (a) having bonding set IFF_SLAVE sooner in the enslavement processing than currently occurs (before open, not after), and (b) having ipv6 addrconf ignore UP and CHANGE events on slave devices. The eql driver also uses the IFF_SLAVE flag. I inspected eql, and I believe this change is reasonable for its usage of IFF_SLAVE, but I did not test it. Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | atl1: remove write-only var in tx handlerAlexey Dobriyan2007-07-10
| | | | | | | | | | | | | | | Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | macmace: use "unsigned long flags;"Alexey Dobriyan2007-07-10
| | | | | | | | | | | | | | | | | | | | | Code will do local_irq_save() on it. Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | Cleanup usbnet_probe() return value handlingPeter Korsgaard2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | usbnet_probe() handles a positive return value from the driver bind() function as success, but will later only setup the status handler if the return value was zero, leading to confusion. Patch adjusts this to accept positive values as success in both checks. Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | netxen: deinline and sparse fixStephen Hemminger2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Get rid of dubious casts to (void *) which causes a sparse warning. And move largeish function from inline to the one file that uses the code, the compiler can then decide to inline it. Compile tested only. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | eeprom_93cx6: shorten pulse timing to match spec (bis)Francois Romieu2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Based on an original idea by John W. Linville. It is the missing part of 42d45ccd60636c28e35c2016f091783bc14ad99c Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | phylib: Add Marvell 88E1112 phy idOlof Johansson2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the 88E1111 inits. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | phylib: cleanup marvell.c a bitOlof Johansson2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Simplify the marvell driver init a bit: Make the supported devices an array instead of explicitly registering each structure. This makes it considerably easier to add new devices down the road. Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | AX88796 network driverBen Dooks2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support for the Asix AX88796 network controller, an NE2000 compatible 10/100 ethernet device with internal PHY. The driver supports PHY settings via either ioctl() or the ethtool driver ops. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | IOC3: Switch to pci refcounting safe APIsAlan Cox2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert the IOC3 driver to use ref counting pci interfaces so that we can obsolete the (usually unsafe) pci_find_{slot/device} interfaces and avoid future authors writing hotplug-unsafe device drivers. Signed-off-by: Alan Cox <alan@redhat.com> Build fixes: Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | e100: Fix Tyan motherboard e100 not receiving IPMI commandsDavid Graham2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 82550 & 51 parts have an extended configuration block that includes a bit "GMRC", required to enable the expected TCO behavior, in config byte offset 22d. The config block sent by the failing driver does include the extension area, but this bit is not initialised, and the downlaod only specifies 0x16 bytes to be sent to the NIC (thaht's bytes 00..21d). By initializing the GMRC bit, and extending the download size for D102+ MACs, the problem is resolved. Signed-off-by: David Graham <david.graham@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | QE Ethernet driver writes to wrong register to mask interruptsTimur Tabi2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | The QE Ethernet driver was writing to the wrong register to mask interrupts. In ucc_geth_stop(), it was clearing UCCE instead of UCCM. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | rrunner.c:rr_init() must be __devinitAdrian Bunk2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following section mismatch: <-- snip --> ... MODPOST vmlinux WARNING: drivers/built-in.o(.text+0x26e3f2): Section mismatch: reference to .init.text:rr_init (between 'rr_init_one' and 'rr_remove_one') ... <-- snip --> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | tokenring/3c359.c:xl_init() must be __devinitAdrian Bunk2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following section mismatch: <-- snip --> ... MODPOST vmlinux WARNING: drivers/built-in.o(.text+0x361ef1): Section mismatch: reference to .init.text:xl_init (between 'xl_probe' and 'xl_hw_reset') ... <-- snip --> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | sis900_mii_probe() must be __devinitAdrian Bunk2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes the following section mismatch: <-- snip --> ... MODPOST vmlinux WARNING: drivers/built-in.o(.text+0x298170): Section mismatch: reference to .init.text:sis900_mii_probe (between 'sis900_probe' and 'sis900_default_phy') ... <-- snip --> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | Fix typo in drivers/net/s2io.cRolf Eike Beer2007-07-10
| | | | | | | | | | | | | | | | | | | | | Introduced in d796fdb708fc5b10112934cba43e832c36ce4923. Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | PCMCIA: add Socket Ethernet card into pcnet_csMarcin Juszkiewicz2007-07-10
| | | | | | | | | | | | | | | | | | | | | One card submitted by Ångström user. Signed-off-by: Marcin Juszkiewicz <openembedded@hrw.one.pl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | spidernet: improve interrupt handlingIshizaki Kou2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We intend this patch to improve spidernet interrupt handling to be more strict. We had following problem and this patch solves it. -when CONFIG_DEBUG_SHIRQ=y, request_irq() calls handler(). -when spider_net_open() is called, it calls request_irq() which calls spider_net_interrupt(). -if some specific interrupt bit is set at this timing, it calls netif_rx_schedule() and spider_net_poll() is scheduled. -spider_net_open() calls netif_poll_enable() which clears the bit __LINK_STATE_RX_SCHED. -when spider_net_poll() is called, it calls netif_rx_complete() which causes BUG_ON() because __LINK_STATE_RX_SCHED is not set. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | 3cSOHO100-TX needs EXTRA_PREAMBLESteffen Klassert2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The 3cSOHO100-TX needs a mdio_sync() before mdio_read() to read the MII transceiver registers properly. Adding EXTRA_PREAMBLE to drv_flags of the 3cSOHO100-TX will force this. This problem exists already for years (I checked back to 2.6.8). Setting duplex for the 3cSOHO100-TX was more or less a random process. Till 2.6.15 it was more likely that the diver ends up in half duplex mode, after the code change in 2.6.16 it was more likely to end up in full duplex mode. I wonder why nobody noticed this earier. Hopefully addresses Bug 7454 3c59x (3cSOHO100-TX Hurricane) slow network bug http://bugzilla.kernel.org/show_bug.cgi?id=7454 and Bug 3654 3cSOHO100-TX: No MII transceiver present http://bugzilla.kernel.org/show_bug.cgi?id=3654 Cc: Jonas Sandberg <jonassa@gmail.com> Cc: Jon Sanchez <bugs@niluje.net> Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | Use is_power_of_2() in myri10ge/myri10ge.cvignesh babu2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Replace (n & (n-1)) with is_power_of_2() Signed-off-by: vignesh babu <vignesh.babu@wipro.com> Cc: Brice Goglin <brice@myri.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | use is_power_of_2() in cxgb3/cxgb3_main.cvignesh babu2007-07-10
| | | | | | | | | | | | | | | | | | | | | | | | Replace (n & (n-1)) with is_power_of_2() Signed-off-by: vignesh babu <vignesh.babu@wipro.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | atari_pamsnet.c: old declaration ritchie style fixYoann Padioleau2007-07-10
| | | | | | | | | | | | | | | | | | | | | Use consistent function declaration style. Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | sky2: 1.16 versionStephen Hemminger2007-07-10
| | | | | | | | | | | | | | | Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | sky2: remove some leftover debug messagesStephen Hemminger2007-07-10
| | | | | | | | | | | | | | | | | | | | | Eliminate extra debug messages Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | sky2: use upper_32_bits() macroStephen Hemminger2007-07-10
| | | | | | | | | | | | | | | | | | | | | Use upper_32_bits() inline Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * | sky2: use roundup() macroStephen Hemminger2007-07-10
| | | | | | | | | | | | | | | | | | | | | Use roundup() macro to size receive buffer. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-21 08:42:00 -0500