| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The PCI spec indicates that with stable power, reset needs to be
asserted for a minimum of 1ms (Trst). We should be able to assume
stable power for a Hot Reset, but we add another millisecond as
a fudge factor to make sure the reset is seen on the bus for at least
a full 1ms.
After reset is de-asserted we must wait for devices to complete
initialization. The specs refer to this as "recovery time" (Trhfa).
For PCI this is 2^25 clock cycles or 2^26 for PCI-X. For minimum
bus speeds, both of those come to 1s. PCIe "softens" this
requirement with the Configuration Request Retry Status (CRS)
completion status. Theoretically we could use CRS to shorten the
wait time. We don't make use of that here, using a fixed 1s delay
to allow devices to re-initialize.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Devices come out of reset in D0. Restoring a device to a different
post-reset state takes more smarts than our simple config space
restore, which can leave devices in an inconsistent state. For
example, if a device is reset in D3, but the restore doesn't
successfully return the device to D3, then the actual state of the
device and dev->current_state are contradictory. Put everything
in D0 going into the reset, then we don't need to do anything
special on the way out.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sometimes pci_reset_function() is not sufficient. We have cases where
devices do not support any kind of reset, but there might be multiple
functions on the bus preventing pci_reset_function() from doing a
secondary bus reset. We also have cases where a device will advertise
that it supports a PM reset, but really does nothing on D3hot->D0
(graphics cards are notorious for this). These devices often also
have more than one function, so even blacklisting PM reset for them
wouldn't allow a secondary bus reset through pci_reset_function().
If a driver supports multiple devices it should have the ability to
induce a bus reset when it needs to. This patch provides that ability
through pci_reset_slot() and pci_reset_bus(). It's the caller's
responsibility when using these interfaces to understand that all of
the devices in or below the slot (or on or below the bus) will be
reset and therefore should be under control of the caller. PCI state
of all the affected devices is saved and restored around these resets,
but internal state of all of the affected devices is reset (which
should be the intention).
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
| |
Only cosmetic code changes to existing paths. Expand the comment in
the new pci_dev_save_and_disable() function since there's a lot
hidden in that Command register write.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
| |
If the hotplug controller provides a way to reset a slot, use that
before a direct parent bus reset. Like the bus reset option, this is
only available when a single pci_dev occupies the slot.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
|
| |
PCIe hotplug has a bus per slot, so we can just use a normal
secondary bus reset. However, if a slot supports surprise removal,
a bus reset can be seen as a presence detection change triggering
a hot-remove followed by a hot-add. Disable presence detection from
triggering an interrupt or being polled around the bus reset.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
|
| |
This optional callback allows hotplug controllers to perform slot
specific resets. These may be necessary in cases where a normal
secondary bus reset can interact with controller logic and expose
spurious hotplugs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| |
|
|
|
|
|
|
| |
Move the secondary bus reset code from pci_parent_bus_reset() into its own
function. Export it as we'll later be calling it from hotplug controllers
and elsewhere.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| | |
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI video support fixes from Rafael Wysocki:
"I'm sending a separate pull request for this as it may be somewhat
controversial. The breakage addressed here is not really new and the
fixes may not satisfy all users of the affected systems, but we've had
so much back and forth dance in this area over the last several weeks
that I think it's time to actually make some progress.
The source of the problem is that about a year ago we started to tell
BIOSes that we're compatible with Windows 8, which we really need to
do, because some systems shipping with Windows 8 are tested with it
and nothing else, so if we tell their BIOSes that we aren't compatible
with Windows 8, we expose our users to untested BIOS/AML code paths.
However, as it turns out, some Windows 8-specific AML code paths are
not tested either, because Windows 8 actually doesn't use the ACPI
methods containing them, so if we declare Windows 8 compatibility and
attempt to use those ACPI methods, things break. That occurs mostly
in the backlight support area where in particular the _BCM and _BQC
methods are plain unusable on some systems if the OS declares Windows
8 compatibility.
[ The additional twist is that they actually become usable if the OS
says it is not compatible with Windows 8, but that may cause
problems to show up elsewhere ]
Investigation carried out by Matthew Garrett indicates that what
Windows 8 does about backlight is to leave backlight control up to
individual graphics drivers. At least there's evidence that it does
that if the Intel graphics driver is used, so we've decided to follow
Windows 8 in that respect and allow i915 to control backlight (Daniel
likes that part).
The first commit from Aaron Lu makes ACPICA export the variable from
which we can infer whether or not the BIOS believes that we are
compatible with Windows 8.
The second commit from Matthew Garrett prepares the ACPI video driver
by making it initialize the ACPI backlight even if it is not going to
be used afterward (that is needed for backlight control to work on
Thinkpads).
The third commit implements the actual workaround making i915 take
over backlight control if the firmware thinks it's dealing with
Windows 8 and is based on the work of multiple developers, including
Matthew Garrett, Chun-Yi Lee, Seth Forshee, and Aaron Lu.
The final commit from Aaron Lu makes us follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled by
GUI.
Hopefully, this approach will allow us to avoid using blacklists of
systems that should not declare Windows 8 compatibility just to avoid
backlight control problems in the future.
- Change from Aaron Lu makes ACPICA export a variable which can be
used by driver code to determine whether or not the BIOS believes
that we are compatible with Windows 8.
- Change from Matthew Garrett makes the ACPI video driver initialize
the ACPI backlight even if it is not going to be used afterward
(that is needed for backlight control to work on Thinkpads).
- Fix from Rafael J Wysocki implements Windows 8 backlight support
workaround making i915 take over bakclight control if the firmware
thinks it's dealing with Windows 8. Based on the work of multiple
developers including Matthew Garrett, Chun-Yi Lee, Seth Forshee,
and Aaron Lu.
- Fix from Aaron Lu makes the kernel follow Windows 8 by informing
the firmware through the _DOS method that it should not carry out
automatic brightness changes, so that brightness can be controlled
by GUI"
* tag 'acpi-video-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: no automatic brightness changes by win8-compatible firmware
ACPI / video / i915: No ACPI backlight if firmware expects Windows 8
ACPI / video: Always call acpi_video_init_brightness() on init
ACPICA: expose OSI version
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Starting from win8, MS backlight control driver will set bit 2 of the
parameter of control method _DOS, to inform firmware it should not
perform any automatic brightness changes. This mostly affects hotkey
notification deliver - if we do not set this bit, on hotkey press,
firmware may choose to adjust brightness level instead of sending out
notification and doing nothing.
So this patch sets bit 2 when calling _DOS so that GUIs can show the
notification window on hotkey press. This behavior change is only
necessary for win8 systems.
The MS document on win8 backlight control is here:
http://msdn.microsoft.com/en-US/library/windows/hardware/jj159305
References: https://bugzilla.kernel.org/show_bug.cgi?id=52951
References: https://bugzilla.kernel.org/show_bug.cgi?id=56711
Reported-by: Micael Dias <kam1kaz3@gmail.com>
Reported-by: Dan Garton <dan.garton@gmail.com>
Reported-by: Bob Ziuchkovski <bob.ziuchkovski@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
According to Matthew Garrett, "Windows 8 leaves backlight control up
to individual graphics drivers rather than making ACPI calls itself.
There's plenty of evidence to suggest that the Intel driver for
Windows [8] doesn't use the ACPI interface, including the fact that
it's broken on a bunch of machines when the OS claims to support
Windows 8. The simplest thing to do appears to be to disable the
ACPI backlight interface on these systems".
There's a problem with that approach, however, because simply
avoiding to register the ACPI backlight interface if the firmware
calls _OSI for Windows 8 may not work in the following situations:
(1) The ACPI backlight interface actually works on the given system
and the i915 driver is not loaded (e.g. another graphics driver
is used).
(2) The ACPI backlight interface doesn't work on the given system,
but there is a vendor platform driver that will register its
own, equally broken, backlight interface if not prevented from
doing so by the ACPI subsystem.
Therefore we need to allow the ACPI backlight interface to be
registered until the i915 driver is loaded which then will unregister
it if the firmware has called _OSI for Windows 8 (or will register
the ACPI video driver without backlight support if not already
present).
For this reason, introduce an alternative function for registering
ACPI video, acpi_video_register_with_quirks(), that will check
whether or not the ACPI video driver has already been registered
and whether or not the backlight Windows 8 quirk has to be applied.
If the quirk has to be applied, it will block the ACPI backlight
support and either unregister the backlight interface if the ACPI
video driver has already been registered, or register the ACPI
video driver without the backlight interface otherwise. Make
the i915 driver use acpi_video_register_with_quirks() instead of
acpi_video_register() in i915_driver_load().
This change is based on earlier patches from Matthew Garrett,
Chun-Yi Lee and Seth Forshee and includes a fix from Aaron Lu's.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51231
Tested-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Tested-by: Yves-Alexis Perez <corsac@debian.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We have to call acpi_video_init_brightness() even if we're not going
to initialise the backlight - Thinkpads seem to use this as the
trigger for enabling ACPI notifications rather than handling it in
firmware.
[rjw: Drop the brightness object created by
acpi_video_init_brightness() if we are not going to use it.]
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Expose acpi_gbl_osi_data so that code outside of ACPICA can check
the value of the last successfull _OSI call. The definitions for
OSI versions are moved to actypes.h so that other components can
access them too.
Based on a patch from Matthew Garrett which in turn was based on
an earlier patch from Seth Forshee.
[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext[34] tmpfile bugfix from Ted Ts'o:
"Fix regression caused by commit af51a2ac36d1f which added ->tmpfile()
support (along with a similar fix for ext3)"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext3: fix a BUG when opening a file with O_TMPFILE flag
ext4: fix a BUG when opening a file with O_TMPFILE flag
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When we try to open a file with O_TMPFILE flag, we will trigger a bug.
The root cause is that in ext4_orphan_add() we check ->i_nlink == 0 and
this check always fails because we set ->i_nlink = 1 in
inode_init_always(). We can use the following program to trigger it:
int main(int argc, char *argv[])
{
int fd;
fd = open(argv[1], O_TMPFILE, 0666);
if (fd < 0) {
perror("open ");
return -1;
}
close(fd);
return 0;
}
The oops message looks like this:
kernel: kernel BUG at fs/ext3/namei.c:1992!
kernel: invalid opcode: 0000 [#1] SMP
kernel: Modules linked in: ext4 jbd2 crc16 cpufreq_ondemand ipv6 dm_mirror dm_region_hash dm_log dm_mod parport_pc parport serio_raw sg dcdbas pcspkr i2c_i801 ehci_pci ehci_hcd button acpi_cpufreq mperf e1000e ptp pps_core ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core ext3 jbd sd_mod ahci libahci libata scsi_mod uhci_hcd
kernel: CPU: 0 PID: 2882 Comm: tst_tmpfile Not tainted 3.11.0-rc1+ #4
kernel: Hardware name: Dell Inc. OptiPlex 780 /0V4W66, BIOS A05 08/11/2010
kernel: task: ffff880112d30050 ti: ffff8801124d4000 task.ti: ffff8801124d4000
kernel: RIP: 0010:[<ffffffffa00db5ae>] [<ffffffffa00db5ae>] ext3_orphan_add+0x6a/0x1eb [ext3]
kernel: RSP: 0018:ffff8801124d5cc8 EFLAGS: 00010202
kernel: RAX: 0000000000000000 RBX: ffff880111510128 RCX: ffff8801114683a0
kernel: RDX: 0000000000000000 RSI: ffff880111510128 RDI: ffff88010fcf65a8
kernel: RBP: ffff8801124d5d18 R08: 0080000000000000 R09: ffffffffa00d3b7f
kernel: R10: ffff8801114683a0 R11: ffff8801032a2558 R12: 0000000000000000
kernel: R13: ffff88010fcf6800 R14: ffff8801032a2558 R15: ffff8801115100d8
kernel: FS: 00007f5d172b5700(0000) GS:ffff880117c00000(0000) knlGS:0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
kernel: CR2: 00007f5d16df15d0 CR3: 0000000110b1d000 CR4: 00000000000407f0
kernel: Stack:
kernel: 000000000000000c ffff8801048a7dc8 ffff8801114685a8 ffffffffa00b80d7
kernel: ffff8801124d5e38 ffff8801032a2558 ffff88010ce24d68 0000000000000000
kernel: ffff88011146b300 ffff8801124d5d44 ffff8801124d5d78 ffffffffa00db7e1
kernel: Call Trace:
kernel: [<ffffffffa00b80d7>] ? journal_start+0x8c/0xbd [jbd]
kernel: [<ffffffffa00db7e1>] ext3_tmpfile+0xb2/0x13b [ext3]
kernel: [<ffffffff821076f8>] path_openat+0x11f/0x5e7
kernel: [<ffffffff821c86b4>] ? list_del+0x11/0x30
kernel: [<ffffffff82065fa2>] ? __dequeue_entity+0x33/0x38
kernel: [<ffffffff82107cd5>] do_filp_open+0x3f/0x8d
kernel: [<ffffffff82112532>] ? __alloc_fd+0x50/0x102
kernel: [<ffffffff820f9296>] do_sys_open+0x13b/0x1cd
kernel: [<ffffffff820f935c>] SyS_open+0x1e/0x20
kernel: [<ffffffff82398c02>] system_call_fastpath+0x16/0x1b
kernel: Code: 39 c7 0f 85 67 01 00 00 0f b7 03 25 00 f0 00 00 3d 00 40 00 00 74 18 3d 00 80 00 00 74 11 3d 00 a0 00 00 74 0a 83 7b 48 00 74 04 <0f> 0b eb fe 49 8b 85 50 03 00 00 4c 89 f6 48 c7 c7 c0 99 0e a0
kernel: RIP [<ffffffffa00db5ae>] ext3_orphan_add+0x6a/0x1eb [ext3]
kernel: RSP <ffff8801124d5cc8>
Here we couldn't call clear_nlink() directly because in d_tmpfile() we
will call inode_dec_link_count() to decrease ->i_nlink. So this commit
tries to call d_tmpfile() before ext4_orphan_add() to fix this problem.
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Jan Kara <jack@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When we try to open a file with O_TMPFILE flag, we will trigger a bug.
The root cause is that in ext4_orphan_add() we check ->i_nlink == 0 and
this check always fails because we set ->i_nlink = 1 in
inode_init_always(). We can use the following program to trigger it:
int main(int argc, char *argv[])
{
int fd;
fd = open(argv[1], O_TMPFILE, 0666);
if (fd < 0) {
perror("open ");
return -1;
}
close(fd);
return 0;
}
The oops message looks like this:
kernel BUG at fs/ext4/namei.c:2572!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in: dlci bridge stp hidp cmtp kernelcapi l2tp_ppp l2tp_netlink l2tp_core sctp libcrc32c rfcomm tun fuse nfnetli
nk can_raw ipt_ULOG can_bcm x25 scsi_transport_iscsi ipx p8023 p8022 appletalk phonet psnap vmw_vsock_vmci_transport af_key vmw_vmci rose vsock atm can netrom ax25 af_rxrpc ir
da pppoe pppox ppp_generic slhc bluetooth nfc rfkill rds caif_socket caif crc_ccitt af_802154 llc2 llc snd_hda_codec_realtek snd_hda_intel snd_hda_codec serio_raw snd_pcm pcsp
kr edac_core snd_page_alloc snd_timer snd soundcore r8169 mii sr_mod cdrom pata_atiixp radeon backlight drm_kms_helper ttm
CPU: 1 PID: 1812571 Comm: trinity-child2 Not tainted 3.11.0-rc1+ #12
Hardware name: Gigabyte Technology Co., Ltd. GA-MA78GM-S2H/GA-MA78GM-S2H, BIOS F12a 04/23/2010
task: ffff88007dfe69a0 ti: ffff88010f7b6000 task.ti: ffff88010f7b6000
RIP: 0010:[<ffffffff8125ce69>] [<ffffffff8125ce69>] ext4_orphan_add+0x299/0x2b0
RSP: 0018:ffff88010f7b7cf8 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff8800966d3020 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff88007dfe70b8 RDI: 0000000000000001
RBP: ffff88010f7b7d40 R08: ffff880126a3c4e0 R09: ffff88010f7b7ca0
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8801271fd668
R13: ffff8800966d2f78 R14: ffff88011d7089f0 R15: ffff88007dfe69a0
FS: 00007f70441a3740(0000) GS:ffff88012a800000(0000) knlGS:00000000f77c96c0
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000002834000 CR3: 0000000107964000 CR4: 00000000000007e0
DR0: 0000000000780000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000600
Stack:
0000000000002000 00000020810b6dde 0000000000000000 ffff88011d46db00
ffff8800966d3020 ffff88011d7089f0 ffff88009c7f4c10 ffff88010f7b7f2c
ffff88007dfe69a0 ffff88010f7b7da8 ffffffff8125cfac ffff880100000004
Call Trace:
[<ffffffff8125cfac>] ext4_tmpfile+0x12c/0x180
[<ffffffff811cba78>] path_openat+0x238/0x700
[<ffffffff8100afc4>] ? native_sched_clock+0x24/0x80
[<ffffffff811cc647>] do_filp_open+0x47/0xa0
[<ffffffff811db73f>] ? __alloc_fd+0xaf/0x200
[<ffffffff811ba2e4>] do_sys_open+0x124/0x210
[<ffffffff81010725>] ? syscall_trace_enter+0x25/0x290
[<ffffffff811ba3ee>] SyS_open+0x1e/0x20
[<ffffffff816ca8d4>] tracesys+0xdd/0xe2
[<ffffffff81001001>] ? start_thread_common.constprop.6+0x1/0xa0
Code: 04 00 00 00 89 04 24 31 c0 e8 c4 77 04 00 e9 43 fe ff ff 66 25 00 d0 66 3d 00 80 0f 84 0e fe ff ff 83 7b 48 00 0f 84 04 fe ff ff <0f> 0b 49 8b 8c 24 50 07 00 00 e9 88 fe ff ff 0f 1f 84 00 00 00
Here we couldn't call clear_nlink() directly because in d_tmpfile() we
will call inode_dec_link_count() to decrease ->i_nlink. So this commit
tries to call d_tmpfile() before ext4_orphan_add() to fix this problem.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Tested-by: Darrick J. Wong <darrick.wong@oracle.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
|
| |\ \ \
| |/ /
|/| |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg KH:
"Here are a few iio driver fixes for 3.11-rc2. They are still spread
across drivers/iio and drivers/staging/iio so they are coming in
through this tree.
I've also removed the drivers/staging/csr/ driver as the developers
who originally sent it to me have moved on to other companies, and CSR
still will not send us the specs for the device, making the driver
pretty much obsolete and impossible to fix up. Deleting it now
prevents people from sending in lots of tiny codingsyle fixes that
will never go anywhere.
It also helps to offset the large lustre filesystem merge that
happened in 3.11-rc1 in the overall 3.11.0 diffstat. :)"
* tag 'staging-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: csr: remove driver
iio: lps331ap: Fix wrong in_pressure_scale output value
iio staging: fix lis3l02dq, read error handling
staging:iio:ad7291: add missing .driver_module to struct iio_info
iio: ti_am335x_adc: add missing .driver_module to struct iio_info
iio: mxs-lradc: Remove useless check in read_raw
iio: mxs-lradc: Fix misuse of iio->trig
iio: inkern: fix iio_convert_raw_to_processed_unlocked
iio: Fix iio_channel_has_info
iio:trigger: device_unregister->device_del to avoid double free
iio: dac: ad7303: fix error return code in ad7303_probe()
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The first round of IIO fixes for the 3.11 cycle.
This set is larger than I would like, partly due to my lack of review
time in the weeks before the merge window and partly because a
couple of large drivers and the subsystem as a whole seem to be
getting a lot more exposure and testing recently.
1) A long term bug in trigger handling gave a double free of the device.
2) Wrong return value handling means offsets are ignored in
iio_convert_raw_to_processed_unlocked.
3) The iio_channel_has_info utility function was incorrectly updated
during the recent info_mask split, this is now fixed.
4) mxs-lradc has a couple of little fixes.
5) A couple of missing .driver_module entries meant that drivers
could be removed from underneath their users.
6) Error path fixes for ad7303 and lis3l02dq.
7) The scale value for presure in the lps331ap driver was out by
a factor of 100.
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This patch fixes improper in_pressure_scale output that is
returned by the lps331ap barometer sensor driver. According
to the documentation the pressure after applying the scale has to
be expressed in kilopascal units. With erroneous implementation
the scale value larger by two orders of magnitude is returned -
2441410 instead of 24414.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add missing .driver_module of struct iio_info. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add missing .driver_module of struct iio_info. This prevents the
module from being removed from underneath its users.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The removed check in the read_raw implementation was always true,
therefore remove it. This also fixes a bug, by closely inspecting
the code, one can notice the iio_validate_scan_mask_onehot() will
always return 1 and therefore the subsequent condition will always
succeed, therefore making the mxs_lradc_read_raw() function always
return -EINVAL; .
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The struct iio_dev .trig field is to be used only by the IIO core,
the driver shall not fill this field. This fixes ugly crash when
the driver is compiled as a module and the module is rmmod'd.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When reading IIO_CHAN_INFO_OFFSET, the return value of iio_channel_read() for
success will be IIO_VAL*, checking for 0 is not correct.
Without this fix the offset applied by iio drivers will be ignored when
converting a raw value to one in appropriate base units (e.g mV) in
a IIO client drivers that use iio_convert_raw_to_processed including
iio-hwmon.
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Since the info_mask split, iio_channel_has_info() is not working correctly.
info_mask_separate and info_mask_shared_by_type, it is not possible to compare
them directly with the iio_chan_info_enum enum. Correct that bit using the BIT()
macro.
Cc: <stable@vger.kernel.org> # 3.10.x
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
iio_trigger unregistration and freeing has been separated in this
code for some time, but it looks like the calls to the device
handling were not appropriately updated.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
| | | |/
| |/|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This driver is not being updated as the specifications are not able to
be gotten from CSR or anyone else. Without those, getting this driver
into proper mergable shape is going to be impossible. So remove the
driver from the tree.
If the specifications ever become available, this patch can be reverted
and the driver fixed up properly.
Reported-by: Lidza Louina <lidza.louina@gmail.com>
Cc: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Cc: Mikko Virkkilä <mikko.virkkila@bluegiga.com>
Cc: Lauri Hintsala <Lauri.Hintsala@bluegiga.com>
Cc: Riku Mettälä <riku.mettala@bluegiga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"The sget() one is a long-standing bug and will need to go into -stable
(in fact, it had been originally caught in RHEL6), the other two are
3.11-only"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: constify dentry parameter in d_count()
livelock avoidance in sget()
allow O_TMPFILE to work with O_WRONLY
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
so that it can be used in places like d_compare/d_hash
without causing a compiler warning.
Signed-off-by: Peng Tao <tao.peng@emc.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Eric Sandeen has found a nasty livelock in sget() - take a mount(2) about
to fail. The superblock is on ->fs_supers, ->s_umount is held exclusive,
->s_active is 1. Along comes two more processes, trying to mount the same
thing; sget() in each is picking that superblock, bumping ->s_count and
trying to grab ->s_umount. ->s_active is 3 now. Original mount(2)
finally gets to deactivate_locked_super() on failure; ->s_active is 2,
superblock is still ->fs_supers because shutdown will *not* happen until
->s_active hits 0. ->s_umount is dropped and now we have two processes
chasing each other:
s_active = 2, A acquired ->s_umount, B blocked
A sees that the damn thing is stillborn, does deactivate_locked_super()
s_active = 1, A drops ->s_umount, B gets it
A restarts the search and finds the same superblock. And bumps it ->s_active.
s_active = 2, B holds ->s_umount, A blocked on trying to get it
... and we are in the earlier situation with A and B switched places.
The root cause, of course, is that ->s_active should not grow until we'd
got MS_BORN. Then failing ->mount() will have deactivate_locked_super()
shut the damn thing down. Fortunately, it's easy to do - the key point
is that grab_super() is called only for superblocks currently on ->fs_supers,
so it can bump ->s_count and grab ->s_umount first, then check MS_BORN and
bump ->s_active; we must never increment ->s_count for superblocks past
->kill_sb(), but grab_super() is never called for those.
The bug is pretty old; we would've caught it by now, if not for accidental
exclusion between sget() for block filesystems; the things like cgroup or
e.g. mtd-based filesystems don't have anything of that sort, so they get
bitten. The right way to deal with that is obviously to fix sget()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| | | | |
| | | |
| | | |
| | | | |
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Fixes for 3.11-rc2, sent at 5pm, in the professoinal style. :-)"
I'm not sure I like this new level of "professionalism".
9-5, people, 9-5.
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: call ext4_es_lru_add() after handling cache miss
ext4: yield during large unlinks
ext4: make the extent_status code more robust against ENOMEM failures
ext4: simplify calculation of blocks to free on error
ext4: fix error handling in ext4_ext_truncate()
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
If there are no items in the extent status tree, ext4_es_lru_add() is
a no-op. So it is not sufficient to call ext4_es_lru_add() before we
try to lookup an entry in the extent status tree. We also need to
call it at the end of ext4_ext_map_blocks(), after items have been
added to the extent status tree.
This could lead to inodes with that have extent status trees but which
are not in the LRU list, which means they won't get considered for
eviction by the es_shrinker.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Zheng Liu <wenqing.lz@taobao.com>
Cc: stable@vger.kernel.org
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
During large unlink operations on files with extents, we can use a lot
of CPU time. This adds a cond_resched() call when starting to examine
the next level of a multi-level extent tree. Multi-level extent trees
are rare in the first place, and this should rarely be executed.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Some callers of ext4_es_remove_extent() and ext4_es_insert_extent()
may not be completely robust against ENOMEM failures (or the
consequences of reflecting ENOMEM back up to userspace may lead to
xfstest or user application failure).
To mitigate against this, when trying to insert an entry in the extent
status tree, try to shrink the inode's extent status tree before
returning ENOMEM. If there are entries which don't record information
about extents under delayed allocations, freeing one of them is
preferable to returning ENOMEM.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
In ext4_ext_map_blocks(), if we have successfully allocated the data
blocks, but then run into trouble inserting the extent into the extent
tree, most likely due to an ENOSPC condition, determine the arguments
to ext4_free_blocks() in a simpler way which is easier to prove to be
correct.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Previously ext4_ext_truncate() was ignoring potential error returns
from ext4_es_remove_extent() and ext4_ext_remove_space(). This can
lead to the on-diks extent tree and the extent status tree cache
getting out of sync, which is particuarlly bad, and can lead to file
system corruption and potential data loss.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Pull NFS client bugfixes from Trond Myklebust:
- Fix a regression against NFSv4 FreeBSD servers when creating a new
file
- Fix another regression in rpc_client_register()
* tag 'nfs-for-3.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix a regression against the FreeBSD server
SUNRPC: Fix another issue with rpc_client_register()
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Technically, the Linux client is allowed by the NFSv4 spec to send
3 word bitmaps as part of an OPEN request. However, this causes the
current FreeBSD server to return NFS4ERR_ATTRNOTSUPP errors.
Fix the regression by making the Linux client use a 2 word bitmap unless
doing NFSv4.2 with labeled NFS.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
| | | |_|/ /
| |/| | |
| | | | |
| | | | |
| | | | |
| | | | | |
Fix the error pathway if rpcauth_create() fails.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
| |\ \ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-next
Pull btrfs fixes from Josef Bacik:
"I'm playing the role of Chris Mason this week while he's on vacation.
There are a few critical fixes for btrfs here, all regressions and
have been tested well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/josef/btrfs-next:
Btrfs: fix wrong write offset when replacing a device
Btrfs: re-add root to dead root list if we stop dropping it
Btrfs: fix lock leak when resuming snapshot deletion
Btrfs: update drop progress before stopping snapshot dropping
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Miao Xie reported the following issue:
The filesystem was corrupted after we did a device replace.
Steps to reproduce:
# mkfs.btrfs -f -m single -d raid10 <device0>..<device3>
# mount <device0> <mnt>
# btrfs replace start -rfB 1 <device4> <mnt>
# umount <mnt>
# btrfsck <device4>
The reason for the issue is that we changed the write offset by mistake,
introduced by commit 625f1c8dc.
We read the data from the source device at first, and then write the
data into the corresponding place of the new device. In order to
implement the "-r" option, the source location is remapped using
btrfs_map_block(). The read takes place on the mapped location, and
the write needs to take place on the unmapped location. Currently
the write is using the mapped location, and this commit changes it
back by undoing the change to the write address that the aforementioned
commit added by mistake.
Reported-by: Miao Xie <miaox@cn.fujitsu.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Stefan Behrens <sbehrens@giantdisaster.de>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
If we stop dropping a root for whatever reason we need to add it back to the
dead root list so that we will re-start the dropping next transaction commit.
The other case this happens is if we recover a drop because we will add a root
without adding it to the fs radix tree, so we can leak it's root and commit root
extent buffer, adding this to the dead root list makes this cleanup happen.
Thanks,
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We aren't setting path->locks[level] when we resume a snapshot deletion which
means we won't unlock the buffer when we free the path. This causes deadlocks
if we happen to re-allocate the block before we've evicted the extent buffer
from cache. Thanks,
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Alex pointed out a problem and fix that exists in the drop one snapshot at a
time patch. If we decide we need to exit for whatever reason (umount for
example) we will just exit the snapshot dropping without updating the drop
progress. So the next time we go to resume we will BUG_ON() because we can't
find the extent we left off at because we never updated it. This patch fixes
the problem.
Cc: stable@vger.kernel.org
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
|
| |\ \ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Pull UML fixes from Richard Weinberger:
"Special thanks goes to Toralf Föster for continuously testing UML and
reporting issues!"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: remove dead code
um: siginfo cleanup
uml: Fix which_tmpdir failure when /dev/shm is a symlink, and in other edge cases
um: Fix wait_stub_done() error handling
um: Mark stub pages mapping with VM_PFNMAP
um: Fix return value of strnlen_user()
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
"me" is not used.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
