aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* rt2x00: Fix beacon de-synchronization while update beaconIgor Perminov2009-08-14
| | | | | | | | | | | | | When beacon is being updated to refresh TIM (AP mode), beacon frames are de-synchronizing (i.e. two neighbor beacon frames - before and after update - are being transmitted with a wrong time interval). That is because xxx_write_beacon should disable beacon generation only while beacon data are being uploaded to the device, but it should not disable the beacon clock. Signed-off-by: Igor Perminov <igor.perminov@inbox.ru> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: LP-PHY: Implement STX synchronizationGábor Stefanik2009-08-14
| | | | | | | The v2+ radio init (B2063) is now complete, modulo BCM4325 support. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rtl818x: Add some documentation to the TX desc flagsMichael Buesch2009-08-14
| | | | | | | Add some TX desc flags docs. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: add missing device list lockingJohannes Berg2009-08-14
| | | | | | | | | | | When calling into the wext code from the NETDEV_UP notifier, we need to hold the devlist_mtx mutex as the wext code ends up calling into channel checks. Reported-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix regression on receiving PS poll framesLuis R. Rodriguez2009-08-14
| | | | | | | | | | | | | | In the the patch: ath9k: use new FIF_PSPOLL configure filter I forgot to add the new FIF_PSPOLL to the supported mask. Without this we mask out the FIF_PSPOLL flag therefore we'd ignore it from mac80211. Cc: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: remove max_bandwidthPat Erley2009-08-14
| | | | | | | | | | This removes the max_bandwidth attribute. It is only ever written to, and is duplicated by max_bandwidth_khz in the regulatory code. Signed-off-by: Pat Erley <pat-lkml@erley.org> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: FIF_PSPOLL filter flag supportIgor Perminov2009-08-14
| | | | | | | | | | This patch implements FIF_PSPOLL filter flag support in rt2x00 drivers, which has been introduced in mac80211 (see http://marc.info/?l=linux-wireless&m=124897986330807&w=2). Signed-off-by: Igor Perminov <igor.perminov@inbox.ru> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix for race condition while update beaconIgor Perminov2009-08-14
| | | | | | | | | | | | | | | | The patch "Implement set_tim callback for all drivers" can cause kernel oops in rt73usb_write_beacon. The oops is caused by one of the following race conditions: * In case of two near calls to set_tim: rt2x00lib_beacondone_iter is cleaning the beacon skb, whereas rt73usb_write_beacon is still using it. * In case of two near updates of beacon: first as the result of set_tim and second as the result of a call from an application (e.g. hostapd). This patch fixes the race condition by rearranging the update logic and guarding rt2x00_intf->beacon->skb with a mutex. Signed-off-by: Igor Perminov <igor.perminov@inbox.ru> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix rounding errors in RSSI average calculationLars Ericsson2009-08-14
| | | | | | | | | | | | | | | | | Small changes in signal level was not detected up by the MOVING_AVERAGE() due to a rounding error, using 'int' type. rt2x00lib_antenna_diversity_eval: rssi: -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 -62 rssi_avg: -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 -57 The signal level reported back could be significantly (5dBm) different from the actual value. A level +3dBm is the same as double the AP output power. Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix quality houskeeping for software diversityLars Ericsson2009-08-14
| | | | | | | | | | | | | | | | Antanna quality statistics is not handled correctly, which leads to software diversity being shutdown completly. The main problem is that during antenna diversity statistics can be reset resulting in loosing the signal strength just before evaluation. rssi history is not updated correctly leading to incorrect comparison material for basing antenna switching on. Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Align ieee80211 header to 4-byte boundary for PCI devicesIvo van Doorn2009-08-14
| | | | | | | | | | Some hardware require the ieee80211 header to be aligned to a 4-byte boundary before mapping it to the DMA. Otherwise some frames (like beacons) will not be send out correctly by the device. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Use IEEE80211_TX_CTL_MORE_FRAMES flagIvo van Doorn2009-08-14
| | | | | | | | | Check the IEEE80211_TX_CTL_MORE_FRAMES flag to help determining if the DMA queue should be kicked. At the moment this is combined with the ieee80211_has_morefrags() but we might remove that later. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Remove usage of deprecated radio_enabled & ↵Ivo van Doorn2009-08-14
| | | | | | | | | | | | IEEE80211_CONF_CHANGE_RADIO_ENABLED In the config() callback function the fields radio_enabled and the change flag IEEE80211_CONF_CHANGE_RADIO_ENABLED have been deprecated. This removes the usage of those fields by improving antenna change detection in the antenna configuration function. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* drivers/net/wireless/ath/ath5k: Change constant nameJulia Lawall2009-08-14
| | | | | | | | | | | Elsewhere, the tqi_type field is compared to constants having a name beginning with AR5K_TX_QUEUE, rather than AR5K_TX_QUEUE_ID. I have thus converted AR5K_TX_QUEUE_ID_CAB to AR5K_TX_QUEUE_CAB. This does, however, change the value, so perhaps something else was wanted. Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: fix locking for SIWFREQJohannes Berg2009-08-14
| | | | | | | | | | | | | | | | | | "cfg80211: validate channel settings across interfaces" contained a locking bug -- in the managed-mode SIWFREQ call it would end up running into a lock recursion. This fixes it by not checking that particular interface for a channel that it needs to stay on, which is as it should be as that's the interface we're setting the channel for. Reported-by: Reinette Chatre <reinette.chatre@intel.com> Reported-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Kalle Valo <kalle.valo@iki.fi> Tested-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: automatically adjust sleep levelJohannes Berg2009-08-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Depending on required latency requested by pm_qos (via mac80211) we can automatically adjust the sleep state. Also, mac80211 has a user-visible dynamic sleep feature where we are supposed to stay awake after sending/receiving frames to better receive response frames to our packets, this can be integrated into the sleep command. Currently, and this patch doesn't change that yet, we default to using sleep level 1 if PS is enabled. With a module parameter to iwlcore, automatic adjustment to changing network latency requirements can be enabled -- this isn't yet the default due to requiring more testing. The goal is to enable automatic adjustment and then go into the deepest possible sleep state possible depending on the networking latency requirements. This patch does, however, enable IEEE80211_HW_SUPPORTS_DYNAMIC_PS to avoid the double-timer (one in software and one in the device) when transmitting -- the exact timeout may be ignored but that is not of big concern. Note also that we keep the hard-coded power indices around for thermal throttling -- the specification of that calls for using the specified power levels. Those can also be selected in debugfs to allow easier testing of such parameters. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: display correct critical temperature infomationWey-Yi Guy2009-08-14
| | | | | | | | | Do not send CT KILL config command twice and correct critical temperature informatiom in dmesg Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix missing EXPORT_SYMBOLReinette Chatre2009-08-14
| | | | | | | | | | When compiling without CONFIG_IWLWIFI_DEBUGFS there is a missing iwl_update_stats symbol. This is fixed by making this function an inline in the case when CONFIG_IWLWIFI_DEBUGFS is not set due to the hot path in which it is used. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: refactor some thermal throttle codeJohannes Berg2009-08-14
| | | | | | | | | | | | | | | Some of the thermal throttle data structures and code are really very intermingled with the sleep (power) control code. They really do belong together in a way since the thermal throttle code uses powersaving to achieve its goal, but it's making it hard to work on the powersave code. Split this up to make that easier. I've also changed the antenna defines to an enum and used the same enum for RX and TX. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: handle the case when set power failWey-Yi Guy2009-08-14
| | | | | | | | | | Modify the power update function, when driver fail to set the power, it should not continue move forward and try to change the rx chain configuration. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix legacy thermal throttling power indexWey-Yi Guy2009-08-14
| | | | | | | | | | | | | | For legacy thermal throttling, set the new Thermal Throttling state and change power index when thermal throttling manager detects temperature changed. The current implementation sets the state to the previous Thermal Throttling state, which causes system to enter wrong power index. The worse case, it will trying to set the lower power index when device reach critical temperature, it will cuase issue for both system and the device. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix thermal throttling locking problemWey-Yi Guy2009-08-14
| | | | | | | | | Move all the thermal throttling functions to background task to make sure do not change power and rx chain in interrupt handler. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: revert uCode Alive notification with timeoutReinette Chatre2009-08-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit "iwlwifi: uCode Alive notification with timeout" introduced a more reliable mechanism for ucode loading. Unfortunately we hit a problem with it frequently enough to make a 4965 unusable. The problem can be seen in debug log below. What this code attempts is to set runtime ucode up to load, start a timer to wait for the alive response from runtime ucode, and if it times out it tries again. As can be seen below we receive the alive response and wake the waiting task _before_ the tasks starts waiting. The task thus times out as the alive response is not received while it is waiting for it and it restarts the device. This starts the cycle all over again. [29739.000819] ieee80211 phy0: U iwl_mac_start enter [29739.005751] ieee80211 phy0: U iwl_prepare_card_hw iwl_prepare_card_hw enter [29739.012798] ieee80211 phy0: U iwl_set_hw_ready hardware ready [29739.057200] ieee80211 phy0: U iwl4965_load_bsm Begin load bsm [29739.063366] ieee80211 phy0: U iwl4965_verify_bsm Begin verify bsm [29739.072485] ieee80211 phy0: U iwl4965_verify_bsm BSM bootstrap uCode image OK [29739.079671] ieee80211 phy0: U iwl4965_load_bsm BSM write complete, poll 0 iterations [29739.257019] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x9 [29739.260964] ieee80211 phy0: I iwl_rx_reply_alive Initialization Alive received. [29739.260964] ieee80211 phy0: U __iwl_up iwlagn is coming up [29739.278571] ieee80211 phy0: U iwl_mac_start Start UP work done. [29739.284509] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 788 [29739.292432] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 10312 [29739.302004] ieee80211 phy0: U iwl_verify_ucode Initialize uCode is good in inst SRAM [29739.309746] ieee80211 phy0: U iwl4965_hw_get_temperature Running temperature calibration [29739.317833] ieee80211 phy0: U iwl4965_hw_get_temperature Calib values R[1-3]: -36 13522 -13496 R4: -2726 [29739.327337] ieee80211 phy0: U iwl4965_hw_get_temperature Calibrated temperature: 310K, 37C [29739.335598] ieee80211 phy0: U iwl4965_init_alive_start Initialization Alive received. [29739.343477] ieee80211 phy0: U iwl4965_set_ucode_ptrs Runtime uCode pointers are set. [29739.351283] ieee80211 phy0: I iwl_rx_reply_alive Alive ucode status 0x00000001 revision 0x1 0x0 [29739.355210] ieee80211 phy0: I iwl_rx_reply_alive Runtime Alive received. [29739.366731] iwlagn 0000:03:00.0: Runtime uCode already alive? Waiting for alive anyway [29743.284110] iwlagn 0000:03:00.0: START_ALIVE timeout after 4000ms. [29743.290337] ieee80211 phy0: U iwl_mac_add_interface enter: type 2 [29744.364089] iwlagn 0000:03:00.0: Runtime timeout after 5000ms [29744.370882] ieee80211 phy0: U iwl_alive_start Runtime Alive received. [29744.377347] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 788 [29744.385287] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 10312 [29744.393397] ieee80211 phy0: U iwlcore_verify_inst_sparse ucode inst image size is 94720 [29744.415835] ieee80211 phy0: U iwl_verify_ucode Runtime uCode is good in inst SRAM Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: Display sensitivity and chain noise informationWey-Yi Guy2009-08-14
| | | | | | | | | | | | | Display sensitivity and chain noise data to help understand the current environment and RF condition. The data is feeded by statistics notification and Beacon from uCode; then used by sensitivity calibration and chain noise calibration to determine how DSP should react to the environment changes Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: uCode statistics notification counterWey-Yi Guy2009-08-14
| | | | | | | | | | | | | | | | | | | Display statistics notification information The information break down into uCode_tx_stats uCode_rx_stats uCode_general_stats and can be found in /sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory The statistic information display in debugFs is based on the last statistics notification from uCode; it might not reflect the current uCode activity. Using "watch" command to monitor the uCode activity should give up-to-date statistics provided by uCode. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: tx/rx queue pointer informationWey-Yi Guy2009-08-14
| | | | | | | | | | | | | | | | Adding debugfs function to show current TxFifo/RxFifo read/write pointer, plus the current tx queue status (wake/stop) for both real and virtual queue. This is part of debug feature set to help debugging driver/uCode. use tx_queue and rx_queue in /sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory to show the current read/write pointer for both TxFifo and RxFifo queue Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: Traffic type and counter for debugFsWey-Yi Guy2009-08-14
| | | | | | | | | | | Break down the traffic type and counter for both Tx and Rx. Enhance the tx_statistics and rx_statistics debugfs function and move to /sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory to help better debugging both driver and uCode related problems. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: new debugging feature for dumping data trafficWey-Yi Guy2009-08-14
| | | | | | | | | | | | | | | | | | | | | | | | | The traffic buffer will only beallocated and used if either bit 23 (IWL_DX_TX) or bit 24 (IWL_DL_RX) of "debug" is set; example: "debug=0x800000" - log tx data traffic "debug=0x1000000" - log rx data traffic "debug=0x1800000" - log both tx and rx traffic The traffic log will store the beginning portion (64 bytes) of the latest 256 of tx and rx packets in the round-robbin buffer for debugging, user can examine the log through debugfs file. How to display the current logged tx/rx traffic and txfifo and rxfifo read/write point: "cat traffic_log" in /sys/kernel/debug/ieee80211/phy0/iwlagn/debug directory By echo "0" to traffic_log file will empty the traffic log buffer and reset both tx and rx taffic log index to 0. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: name changed from "fat" to "ht40"Wey-Yi Guy2009-08-14
| | | | | | | | | Rename "fat" to "ht40" The term "fat channel" is deprecated in favor of "HT40" Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: re-introduce per device debuggingReinette Chatre2009-08-14
| | | | | | | | | | | | | | | | | | | | Commit "iwlwifi: make debug level more user friendly" cleaned up the debug level handling. In doing so it created a single global debug level for all devices. Some setups do consits of more that one iwlwifi device and in these setups there is a requirement that debug levels should be unique per device. We now re-introduce the per device debugging while maintaining the cleanup effort of the previous patch. The maintain the global debug level and now introduce a per-device debug level that will be used if it (the per-device debug level) is set. The per-device debug level can be controlled via the debug_level sysfs file while the global debug level is controlled by the debug module parameter. Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* MAINTAINERS: NETWORKING [WIRELESS] additional patternsJoe Perches2009-08-14
| | | | | | | | Added file patterns drivers/net/wireless and net/mac80211 (and net/rfkill -- JWL) Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* p54: implement rfkillChristian Lamparter2009-08-14
| | | | | | | | | | | | | | This patch implements a basic rfkill support for p54 hardware and removes a rfkill related WARNING: fwio.c: In function ‘p54_setup_mac’: fwio.c:323: warning: ‘radio_enabled’ is deprecated. by abandoning radio_enable in flavour for IEEE80211_CONF_CHANGE_IDLE. Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* p54: Write outside array boundsChristian Lamparter2009-08-14
| | | | | | | | This patch fixes a coding error which allowed the to upper-layer to corrupt limited portions of the phy data. Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Fix hardware key index handlingMichael Buesch2009-08-14
| | | | | | | | | This fixes the hardware encryption keys index and array size handling. Thanks to Gregor Kowski for reporting this issue. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: fix alignment problem in scan requestJohannes Berg2009-08-14
| | | | | | | | | | | | The memory layout for scan requests was rather wrong, we put the scan SSIDs before the channels which could lead to the channel pointers being unaligned in memory. It turns out that using a pointer to the channel array isn't necessary anyway since we can embed a zero-length array into the struct. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: allow DMA optimisationJohannes Berg2009-08-14
| | | | | | | | | | | | | | | | | | | | | | If we have a lot of frames to transmit at once, for instance with fragmentation, it can be an optimisation to only tell the DMA engine about them on the last fragment/frame to avoid banging the IO too much. This patch allows implementation such an optimisation by telling the driver when more frames can be expected. Currently, this is used by mac80211 only on fragmented frames, but could also be used in the future on other frames when the queue was full and there are multiple frames pending. Note that drivers need to be careful when using this flag, they need to kick their DMA engines not just when this flag is clear, but also when the queue gets full so that progress can be made. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: document TX powersave filter requirementsJohannes Berg2009-08-14
| | | | | | | | This documents what's required to implement that TX powersave filter properly wrt. handling hardware queues. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* mac80211: explain TX retry and statusJohannes Berg2009-08-14
| | | | | | | | Add some more documentation including an example so that it's clearer what should be done for TX retries. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* nl80211: add generation number to all dumpsJohannes Berg2009-08-14
| | | | | | | | | | | | | | | | | | | | In order for userspace to be able to figure out whether it obtained a consistent snapshot of data or not when using netlink dumps, we need to have a generation number in each dump message that indicates whether the list has changed or not -- its value is arbitrary. This patch adds such a number to all dumps, this needs some mac80211 involvement to keep track of a generation number to start with when adding/removing mesh paths or stations. The wiphy and netdev lists can be fully handled within cfg80211, of course, but generation numbers need to be stored there as well. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: use reassociation when possibleJohannes Berg2009-08-14
| | | | | | | | | | | | | | | | | | | | | | With the move of everything related to the SME from mac80211 to cfg80211, we lost the ability to send reassociation frames. This adds them back, but only for wireless extensions. With the userspace SME, it shall control assoc vs. reassoc (it already can do so with the nl80211 interface). I haven't touched the connect() implementation, so it is not possible to reassociate with the nl80211 connect primitive. I think that should be done with the NL80211_CMD_ROAM command, but we'll have to see how that can be handled in the future, especially with fullmac chips. This patch addresses only the immediate regression we had in mac80211, which previously sent reassoc. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* cfg80211: validate channel settings across interfacesJohannes Berg2009-08-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, there's a problem that affects regulatory enforcement and connection stability, in that it is possible to switch the channel while connected to a network or joined to an IBSS. The problem comes from the fact that we only validate the channel against the current interface's type, not against any other interface. Thus, you have any type of interface up, additionally bring up a monitor mode interface and switch the channel on the monitor. This will obviously also switch the channel on the other interface. The problem now is that if you do that while sending beacons for IBSS mode, you can switch to a disabled channel or a channel that doesn't allow beaconing. Combined with a managed mode interface connected to an AP instead of an IBSS interface, you can easily break the connection that way. To fix this, this patch validates any channel change with all available interfaces, and disallows such changes on secondary interfaces if another interface is connected to an AP or joined to an IBSS. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: hack to disable filters for fixing associationKalle Valo2009-08-14
| | | | | | | | | | Commit 9cef8737 "mac80211: fix managed mode BSSID handling" broke association in wl1251, most probably because the driver configured the bssid filter incorrectly. Workaround this by disabling filter altogether. This needs to be fixed properly soon. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: add hw scan completed debug messageKalle Valo2009-08-14
| | | | | | | | The logs currently don't show when hw scan has completed, fix that. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: remove Luciano as maintainerKalle Valo2009-08-14
| | | | | | | | Luciano is maintaining wl1271 part. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: rename reg.h to wl1251_reg.hKalle Valo2009-08-14
| | | | | | | | | Now that wl1271 doesn't use reg.h anymore, it can be renamed to wl1251_reg.h. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: use workqueue provided by mac80211Kalle Valo2009-08-14
| | | | | | | | wl1251 should use workqueue created by mac80211 to not block the events workqueue too long. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: move wl1251_acx_wake_up_conditions() to wl1251_ps_set_mode()Kalle Valo2009-08-14
| | | | | | | | It should not be hidden inside wl1251_cmd_ps_mode(). Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: fix channel setting in wl1251_op_config()Kalle Valo2009-08-14
| | | | | | | | | There is a bug in wl1251_op_config(). It was calling join with previous channel. Fix it by setting assigning wl->channel before calling join command. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: create wl1251_join()Kalle Valo2009-08-14
| | | | | | | | | Better to use wl1251_cmd_join() only for sending the command and move the logic to wl1251_join(). Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wl1251: add channel to wl1251_cmd_join() parametersKalle Valo2009-08-14
| | | | | | | | | Because join channel tunes to a channel, better to make it more obvious by adding a parameter for it. Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Reviewed-by: Vidhya Govindan <vidhya.govindan@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-28 12:52:06 -0500