aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* ide: add ide_set_dma() helper (v2)Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | | | | * add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return -1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly) 0 when DMA needs to be enabled (== need to call ->ide_dma_on) 1 when DMA setting shouldn't be changed * fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly v2: * updated for scc_pata Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sgiioc4: fix sgiioc4_ide_dma_check() to enable/disable DMA properlyBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | * use sgiioc4_ide_dma_{on,off_quietly}() instead of changing drive->using_dma directly * fix warning message * add FIXME Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: disable DMA in ->ide_dma_check for "no IORDY" case (v2)Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | If DMA is unsupported ->ide_dma_check should disable DMA. v2: * updated for scc_pata Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: convert ide_hwif_t.mmio into flag (v2)Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | | All users of ->mmio == 1 are gone so convert ->mmio into flag. Noticed by Alan Cox. v2: * updated for scc_pata Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: use PIO/MMIO operations directly where possible (v2)Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | This results in smaller/faster/simpler code and allows future optimizations. Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}. v2: * updated for scc_pata Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: add ide_use_fast_pio() helper (v3)Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * add ide_use_fast_pio() helper for use by host drivers * add DMA capability and hwif->autodma checks to ide_use_dma() - au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1) [ for the IT8211/2 in SMART mode this check shouldn't be made but since in it821x_fixups() we set DMA bit explicitly: if(strstr(id->model, "Integrated Technology Express")) { /* In raid mode the ident block is slightly buggy We need to set the bits so that the IDE layer knows LBA28. LBA48 and DMA ar valid */ id->capability |= 3; /* LBA28, DMA */ we are better off using generic helper if we can ] - ide-cris driver didn't set ->autodma [ before the patch hwif->autodma was only checked in the chipset specific hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check() function so there no behavior change here ] v2: * updated patch description (thanks to Alan Cox for the feedback) v3: * updated for scc_pata driver Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: unexport ide_set_xfer_rate() (v2)Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | | | | | In cmd64x, siimage and scc_pata drivers: * don't set drive->init_speed as it should be already set by successful execution of ide_set_xfer_rate() * use hwif->speedproc functions directly Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate). v2: * updated for scc_pata driver Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove ide_drive_t.usageBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | This field is no longer used by the core IDE code so fix ide-{disk,floppy} drivers to keep openers count in the driver specific objects and remove it from ide-{cd,scsi,tape} drivers (it was write-only). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove ide_pci_device_t tables with only one entryBartlomiej Zolnierkiewicz2007-02-16
| | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove write-only ide_hwif_t.no_dsc flagBartlomiej Zolnierkiewicz2007-02-16
| | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: remove write-only ide_pio_data_t.blacklistedBartlomiej Zolnierkiewicz2007-02-16
| | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sis5513: sis5513_config_xfer_rate() cleanupBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | | * remove bogus comment for sis5513_config_xfer_rate() * there is no need to call config_drive_art_rwp() because it is called by config_art_rwp_pio() * remove needless wrapper * remove stale "TODO" comment (IDE core should provide generic tuning code) Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* piix: cleanupBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | * disable DMA masks if no_piix_dma is set and remove now not needed no_piix_dma_check from piix_config_drive_for_dma() * there is no need to read register 0x55 in init_hwif_piix() * move cable detection code to piix_cable_detect() * remove unreachable 82371MX code from init_hwif_piix() Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* svwks: small cleanupBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | * remove redundant svwks_ide_dma_end() [ __ide_dma_end() is used by default ] * remove init_dma_svwks() so the default ide_setup_dma() function is used [ init_setup_csb6() takes care of not initializing disabled channels ] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* cs5530: small cleanupBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | * BUG() on unknown DMA mode in cs5530_config_dma() * there is no need to call hwif->ide_dma_host_{off,on}() in cs5530_config_dma() because hwif->ide_dma_host_{off,on}() is called by hwif->ide_dma_off_{quietly,on}() Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt366: remove redundant check from init_dma_hpt366()Bartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | ->init_dma() cannot be called with dmabase == 0 (see drivers/ide/setup-pci.c) Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* trm290: remove redundant CONFIG_BLK_DEV_IDEDMA #ifdef-sBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | In drivers/ide/Kconfig BLK_DEV_TRM290 depends on BLK_DEV_IDEDMA_PCI (on which is BLK_DEV_IDEDMA dependant on). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* au1xxx-ide: remove dead codeBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | 'speed' is always equal to 'mode' when ide_config_drive_speed() is called Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_old: remove dead codeBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | CONFIG_PDC202XX_MASTER config option doesn't exist Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* drivers/ide: PATA driver for CellebKou Ishizaki2007-02-16
| | | | | | | | | | | | | | | | | | | | | | This is the patch (based on 2.6.19-rc4) for PATA controller of Toshiba Cell reference set(Celleb). The reference set consists of Cell, 512MB memory, Super Companion Chip(SCC) and some peripherals such as HDD, GbE, etc. You can see brief explanation and picture of Cell reference set at following URLs. http://www.toshiba.co.jp/about/press/2005_09/pr2001.htm http://cell-industries.com/toshiba_announces.php We use a drivers/ide driver because its design is more suitable for SCC IDE controller than libata driver. Since SCC supports only 32bit read/write, we must override many callbacks of ata_port_operations by modifying generic helpers. Each time the libata common code is updated, we must update those modified helpers. It is very hard for us. But we will try to implement the libata driver as needed. Signed-off-by: Kou Ishizaki <kou.ishizaki at toshiba.co.jp> Signed-off-by: Akira Iguchi <akira2.iguchi at toshiba.co.jp> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* sl82c105: DMA support fixesSergei Shtylyov2007-02-16
| | | | | | | | | | | | | | | | | | | | | Fix a number of issues with the DMA support code: - driver claims support for all SW/MW DMA modes while supporting only MWDMA2; - ide_dma_check() method tries to enable DMA on the "known good" drives which don't support MWDMA2; - ide_dma_on() method upon failure to set drive to MWDMA2 re-tunes already tuned PIO mode and calls ide_dma_off() method instead of returning error; - ide_dma_off() method sets drive->current_speed while it doesn't actually change (only the PIO timings are re-loaded into the chip's registers); - init_hwif() method forcibly sets/resets both "drive DMA capable" bits while this is properly handled by ide_dma_{on,off}() methods being called later... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* pdc202xx_old: fix PIO mode setupSergei Shtylyov2007-02-16
| | | | | | | | | | | | | | | Fix the driver's tuneproc() method to always set the PIO mode requested and not pick the best possible one, rename it to pdc202xx_tune_drive(), and change the calls to it accordingly; remove the preceding comment which has nothing to do with the code. Sergei Shtylyov wrote: > The tuneproc() method should take arg 255 for auto-selecting the best PIO > mode, not 5 as it did here + this driver's method always auto-selected instead > of setting the mode it's been told to -- issue typical to drivers/ide/... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* siimage: PIO1/2 taskfile transfer overclocking fixSergei Shtylyov2007-02-16
| | | | | | | | | | | | | | | | | | | | Fix two typos found by SiI680A documentation check. They caused the taskfile transfer overclocking: - in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers; - in PIO mode 2 as data and taskfile timings are swapped when writing to the MMIO regs. Fix coding style and trailing whitespace in enclosing statements while at it... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> drivers/ide/pci/siimage.c | 59 ++++++++++++++++++++++------------------------ 1 file changed, 29 insertions(+), 30 deletions(-)
* ide: remove clearing bmdma status from cdrom_decode_status() (rev #4)Albert Lee2007-02-16
| | | | | | | | | | | | | | patch 2/2: Remove clearing bmdma status from cdrom_decode_status() since ATA devices might need it as well. (http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94) Signed-off-by: Albert Lee <albertcc@tw.ibm.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: "Adam W. Hawks" <awhawks@us.ibm.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide: clear bmdma status in ide_intr() for ICHx controllers (revised #4)Albert Lee2007-02-16
| | | | | | | | | | | | | | | | | | patch 1/2 (revised): - Fix drive->waiting_for_dma to work with CDB-intr devices. - Do the dma status clearing in ide_intr() and add a new hwif->ide_dma_clear_irq for Intel ICHx controllers. Revised per Alan, Sergei and Bart's advice. Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters. Please review/apply, thanks. Signed-off-by: Albert Lee <albertcc@tw.ibm.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: "Adam W. Hawks" <awhawks@us.ibm.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide-floppy: Fix unformatted media crashAlan Cox2007-02-16
| | | | | | | | | | | | | | | | | A ZIP or similar with unformatted media will cause crashes when attempts are made to read/write it in some cases. This is because bs_factor is zero and we divide by it causing an oops. As the size of a non-accessible/non-existant media is really a bit of a zen question it doesn't matter if non-existant media is 512 bytes per sector or zero. Setting it to 1 causes us to generate 512 bytes/sector accesses and error properly. Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh) Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* atiixp/jmicron/triflex: fix PIO fallbackBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | | | | | | | | | | | | | | | | | * atiixp: if DMA can't be used atiixp_config_drive_for_dma() should return 0, atiixp_dma_check() will tune the correct PIO mode anyway * jmicron: if DMA can't be used config_chipset_for_dma() should return 0, micron_config_drive_for_dma() will tune the correct PIO mode anyway config_jmicron_chipset_for_pio(drive, !speed) doesn't program device transfer mode for speed != 0 (only wastes some CPU cycles on ide_get_best_pio_mode() call) so remove it * triflex: if DMA can't be used triflex_config_drive_for_dma() should return 0, triflex_config_drive_xfer_rate() will tune correct PIO mode anyway Above changes also fix (theoretical) issue when ->speedproc fails to set device transfer mode (i.e. when ide_config_drive_speed() fails to program it) but one of DMA transfer modes is already enabled on the device by the BIOS. In such scenario ide_dma_enable() will incorrectly return true statement and ->ide_dma_check will try to enable DMA on the device. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hpt34x: hpt34x_tune_chipset() (->speedproc) fixBartlomiej Zolnierkiewicz2007-02-16
| | | | | | | | * remember to clear reg2 bits for the current device before setting mode * remove no longer needed hpt34x_clear_chipset() Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge branch 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32Linus Torvalds2007-02-16
|\ | | | | | | | | | | | | | | | | | | | | * 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32: [AVR32] Use per-controller spi_board_info structures [AVR32] Warn, don't BUG if clk_disable is called too many times [AVR32] Make sure all genclocks have a parent [AVR32] Remove unnecessary sys_nfsservctl conditional [AVR32] Wire up the SysV IPC calls properly [AVR32] Define ioremap_nocache, ioport_map and ioport_unmap [AVR32] Fix prototypes for __raw_writesb and friends
| * [AVR32] Use per-controller spi_board_info structuresHaavard Skinnemoen2007-02-16
| | | | | | | | | | | | | | | | | | | | Set up one spi_board_info array per controller and pass this to at32_add_device_spi so that it can set up any GPIO pins for chip selects based on this information. Extracted from a patch by David Brownell and adapted slightly. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
| * [AVR32] Warn, don't BUG if clk_disable is called too many timesHaavard Skinnemoen2007-02-16
| | | | | | | | | | | | | | | | | | Print a helpful warning along with a stack dump if clk_disable is called on a already-disabled clock. Remove the BUG_ON(). Extracted from a patch by David Brownell. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
| * [AVR32] Make sure all genclocks have a parentHaavard Skinnemoen2007-02-16
| | | | | | | | | | | | | | | | | | | | | | Initialize the parent field of each generic clock by looking at the PM registers. This means that the genclock operations can always assume that the parent field is non-null, so they don't have to check. Also remove a few unnecessary BUG_ON()s. Extracted from a patch by David Brownell. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
| * [AVR32] Remove unnecessary sys_nfsservctl conditionalHaavard Skinnemoen2007-02-16
| | | | | | | | | | | | | | | | kernel/sys_ni.c defines sys_nfsservctl as a weak alias for sys_ni_syscall, so it's always safe to include it in the system call table. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
| * [AVR32] Wire up the SysV IPC calls properlyHaavard Skinnemoen2007-02-16
| | | | | | | | | | | | | | | | Wire up the individual sysvipc system calls and remove sys_ipc. Strictly speaking, this breaks the ABI, but since sys_ipc never worked anyway due to a silly bug, it isn't actually a regression. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
| * [AVR32] Define ioremap_nocache, ioport_map and ioport_unmapHaavard Skinnemoen2007-02-16
| | | | | | | | | | | | | | These are all defined in terms of ioremap/iounmap since port I/O isn't really different from memory-mapped I/O on AVR32. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
| * [AVR32] Fix prototypes for __raw_writesb and friendsHaavard Skinnemoen2007-02-16
| | | | | | | | | | | | | | The first parameter to __raw_writes[bwl] and __raw_reads[bwl] should be a void __iomem *, not unsigned long. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgartLinus Torvalds2007-02-16
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart: [AGPGART] allow drm populated agp memory types cleanups [AGPGART] intel-agp: Use ARRAY_SIZE macro when appropriate [AGPGART] Add agp-type-to-mask-type method missing from some drivers. [AGPGART] Don't try to remap i810 registers on resume. [AGPGART] Allow drm-populated agp memory types [AGPGART] compat ioctl
| * | [AGPGART] allow drm populated agp memory types cleanupsAndrew Morton2007-02-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | Fix whitespace, braces, use kzalloc(). Cc: Dave Airlie <airlied@linux.ie> Cc: Thomas Hellstrom <thomas@tungstengraphics.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dave Jones <davej@redhat.com>
| * | [AGPGART] intel-agp: Use ARRAY_SIZE macro when appropriateAhmed S. Darwish2007-02-06
| | | | | | | | | | | | | | | | | | | | | use ARRAY_SIZE macro already defined in kernel.h Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Signed-off-by: Dave Jones <davej@redhat.com>
| * | [AGPGART] Add agp-type-to-mask-type method missing from some drivers.Thomas Hellstrom2007-02-05
| | | | | | | | | | | | Signed-off-by: Dave Jones <davej@redhat.com>
| * | [AGPGART] Don't try to remap i810 registers on resume.Dave Jones2007-02-04
| | | | | | | | | | | | | | | | | | | | | | | | We don't unmap them on the suspend path, so on resume trying to remap will fail, and then result in an oops the next time something tries to access them. Signed-off-by: Dave Jones <davej@redhat.com>
| * | [AGPGART] Allow drm-populated agp memory typesThomas Hellstrom2007-02-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch allows drm to populate an agpgart structure with pages of its own. It's needed for the new drm memory manager which dynamically flips pages in and out of AGP. The patch modifies the generic functions as well as the intel agp driver. The intel drm driver is currently the only one supporting the new memory manager. Other agp drivers may need some minor fixing up once they have a corresponding memory manager enabled drm driver. AGP memory types >= AGP_USER_TYPES are not populated by the agpgart driver, but the drm is expected to do that, as well as taking care of cache- and tlb flushing when needed. It's not possible to request these types from user space using agpgart ioctls. The Intel driver also gets a new memory type for pages that can be bound cached to the intel GTT. Signed-off-by: Thomas Hellstrom <thomas@tungstengraphics.com> Signed-off-by: Dave Jones <davej@redhat.com>
| * | [AGPGART] compat ioctlZwane Mwaikambo2007-02-03
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following video card requires the agpgart driver ioctl interface in order to detect video memory. 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS/940GML Express Integrated Graphics Controller (rev 03) Tested on a Thinkpad Z61t, Xorg.0.log from a 32bit debian Xorg is at; http://montezuma.homeunix.net/Xorg.0.log Signed-off-by: Zwane Mwaikambo <zwane@infradead.org> Signed-off-by: Dave Jones <davej@redhat.com>
* | | Merge master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreqLinus Torvalds2007-02-16
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq: [CPUFREQ] Longhaul - Redo Longhaul ver. 2 [CPUFREQ] EPS - Correct 2nd brand test [CPUFREQ] Longhaul - Separate frequency and voltage transition [CPUFREQ] Longhaul - Models of Nehemiah [CPUFREQ] Whitespace fixup [CPUFREQ] Longhaul - Simplier minmult [CPUFREQ] CPU_FREQ_TABLE shouldn't be a def_tristate [CPUFREQ] ondemand governor use new cpufreq rwsem locking in work callback [CPUFREQ] ondemand governor restructure the work callback [CPUFREQ] Rewrite lock in cpufreq to eliminate cpufreq/hotplug related issues [CPUFREQ] Remove hotplug cpu crap [CPUFREQ] Enhanced PowerSaver driver [CPUFREQ] Longhaul - Add VT8235 support [CPUFREQ] Longhaul - Fix guess_fsb function [CPUFREQ] Longhaul - Remove duplicate tables [CPUFREQ] Longhaul - Introduce Nehemiah C [CPUFREQ] fix cpuinfo_cur_freq for CPU_HW_PSTATE [CPUFREQ] Longhaul - Remove "ignore_latency" option
| * | | [CPUFREQ] Longhaul - Redo Longhaul ver. 2Rafał Bilski2007-02-14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Start using v2 version of Longhaul when available. It provides voltage scaling and can use ACPI C3 state. That's curious. CPU will not change frequency on ACPI C3 when v1 is in use, but it will when v2 is used. Driver will return max frequency all the time if this isn't true for all processors. There is strange thing with mobile voltage. Looks like only Nehemiah (C3-M) supports it. Earlier processors have different mobile VRM (in docs), but I can't find any which is using it. Looks like all are using VRM 8.5. So fail for non Nehemiah with mobile VRM. Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com>
| * | | [CPUFREQ] EPS - Correct 2nd brand testRafał Bilski2007-02-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Solution for small, but nasty bug: access beyond end of f_table for C7 brand. Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com>
| * | | [CPUFREQ] Fix up merge conflicts with recent ACPI changes.Dave Jones2007-02-10
| |\ \ \ | | | | | | | | | | | | | | | Signed-off-by: Dave Jones <davej@redhat.com>
| * | | | [CPUFREQ] Longhaul - Separate frequency and voltage transitionRafał Bilski2007-02-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This change should make Longhaul more compatible with both ver. 2 and Powersaver processors. Voltage transitions will be done before or after frequency transition. That depends on direction of change. I don't know how to force conservative governor when voltage scaling is enabled, so there is only a warning for user. Minimal voltage is calculated in different way now because in this way more power is saved at lower multipliers. Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com>
| * | | | [CPUFREQ] Longhaul - Models of NehemiahRafał Bilski2007-02-10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Borowed from VIA driver. Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com>
| * | | | [CPUFREQ] Whitespace fixupDave Jones2007-02-10
| | | | | | | | | | | | | | | | | | | | Signed-off-by: Dave Jones <davej@redhat.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-10-25 03:42:43 -0400