litmus-rt.git - The LITMUS^RT kernel.


#
# Network device configuration
#

menuconfig NETDEVICES
	default y if UML
	depends on NET
	bool "Network device support"
	---help---
	  You can say N here if you don't intend to connect your Linux box to
	  any other computer at all.

	  You'll have to say Y if your computer contains a network card that
	  you want to use under Linux. If you are going to run SLIP or PPP over
	  telephone line or null modem cable you need say Y here. Connecting
	  two machines with parallel ports using PLIP needs this, as well as
	  AX.25/KISS for sending Internet traffic over amateur radio links.

	  See also "The Linux Network Administrator's Guide" by Olaf Kirch and
	  Terry Dawson. Available at <http://www.tldp.org/guides.html>.

	  If unsure, say Y.

# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
if NETDEVICES

config NETDEVICES_MULTIQUEUE
	bool "Netdevice multiple hardware queue support"
	---help---
	  Say Y here if you want to allow the network stack to use multiple
	  hardware TX queues on an ethernet device.

	  Most people will say N here.

config IFB
	tristate "Intermediate Functional Block support"
	depends on NET_CLS_ACT
	---help---
	  This is an intermediate driver that allows sharing of
	  resources.
	  To compile this driver as a module, choose M here: the module
	  will be called ifb.  If you want to use more than one ifb
	  device at a time, you need to compile this driver as a module.
	  Instead of 'ifb', the devices will then be called 'ifb0',
	  'ifb1' etc.
	  Look at the iproute2 documentation directory for usage etc

config DUMMY
	tristate "Dummy net driver support"
	---help---
	  This is essentially a bit-bucket device (i.e. traffic you send to
	  this device is consigned into oblivion) with a configurable IP
	  address. It is most commonly used in order to make your currently
	  inactive SLIP address seem like a real address for local programs.
	  If you use SLIP or PPP, you might want to say Y here. Since this
	  thing often comes in handy, the default is Y. It won't enlarge your
	  kernel either. What a deal. Read about it in the Network
	  Administrator's Guide, available from
	  <http://www.tldp.org/docs.html#guide>.

	  To compile this driver as a module, choose M here: the module
	  will be called dummy.  If you want to use more than one dummy
	  device at a time, you need to compile this driver as a module.
	  Instead of 'dummy', the devices will then be called 'dummy0',
	  'dummy1' etc.

config BONDING
	tristate "Bonding driver support"
	depends on INET
	---help---
	  Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
	  Channels together. This is called 'Etherchannel' by Cisco,
	  'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.

	  The driver supports multiple bonding modes to allow for both high
	  performance and high availability operation.

	  Refer to <file:Documentation/networking/bonding.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called bonding.

config MACVLAN
	tristate "MAC-VLAN support (EXPERIMENTAL)"
	depends on EXPERIMENTAL
	---help---
	  This allows one to create virtual interfaces that map packets to
	  or from specific MAC addresses to a particular interface.

	  To compile this driver as a module, choose M here: the module
	  will be called macvlan.

config EQUALIZER
	tristate "EQL (serial line load balancing) support"
	---help---
	  If you have two serial connections to some other computer (this
	  usually requires two modems and two telephone lines) and you use
	  SLIP (the protocol for sending Internet traffic over telephone
	  lines) or PPP (a better SLIP) on them, you can make them behave like
	  one double speed connection using this driver.  Naturally, this has
	  to be supported at the other end as well, either with a similar EQL
	  Linux driver or with a Livingston Portmaster 2e.

	  Say Y if you want this and read
	  <file:Documentation/networking/eql.txt>.  You may also want to read
	  section 6.2 of the NET-3-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here: the module
	  will be called eql.  If unsure, say N.

config TUN
	tristate "Universal TUN/TAP device driver support"
	select CRC32
	---help---
	  TUN/TAP provides packet reception and transmission for user space
	  programs.  It can be viewed as a simple Point-to-Point or Ethernet
	  device, which instead of receiving packets from a physical media,
	  receives them from user space program and instead of sending packets
	  via physical media writes them to the user space program.

	  When a program opens /dev/net/tun, driver creates and registers
	  corresponding net device tunX or tapX.  After a program closed above
	  devices, driver will automatically delete tunXX or tapXX device and
	  all routes corresponding to it.

	  Please read <file:Documentation/networking/tuntap.txt> for more
	  information.

	  To compile this driver as a module, choose M here: the module
	  will be called tun.

	  If you don't know what to use this for, you don't need it.

config VETH
	tristate "Virtual ethernet device"
	---help---
	  The device is an ethernet tunnel. Devices are created in pairs. When
	  one end receives the packet it appears on its pair and vice versa.

config NET_SB1000
	tristate "General Instruments Surfboard 1000"
	depends on PNP
	---help---
	  This is a driver for the General Instrument (also known as
	  NextLevel) SURFboard 1000 internal
	  cable modem. This is an ISA card which is used by a number of cable
	  TV companies to provide cable modem access. It's a one-way
	  downstream-only cable modem, meaning that your upstream net link is
	  provided by your regular phone modem.

	  At present this driver only compiles as a module, so say M here if
	  you have this card. The module will be called sb1000. Then read
	  <file:Documentation/networking/README.sb1000> for information on how
	  to use this module, as it needs special ppp scripts for establishing
	  a connection. Further documentation and the necessary scripts can be
	  found at:

	  <http://www.jacksonville.net/~fventuri/>
	  <http://home.adelphia.net/~siglercm/sb1000.html>
	  <http://linuxpower.cx/~cable/>

	  If you don't have this card, of course say N.

config IP1000
       tristate "IP1000 Gigabit Ethernet support"
       depends on PCI && EXPERIMENTAL
       ---help---
         This driver supports IP1000 gigabit Ethernet cards.

         To compile this driver as a module, choose M here: the module
         will be called ipg.  This is recommended.

source "drivers/net/arcnet/Kconfig"

source "drivers/net/phy/Kconfig"

#
#	Ethernet
#

menuconfig NET_ETHERNET
	bool "Ethernet (10 or 100Mbit)"
	depends on !UML
	---help---
	  Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common
	  type of Local Area Network (LAN) in universities and companies.

	  Common varieties of Ethernet are: 10BASE-2 or Thinnet (10 Mbps over
	  coaxial cable, linking computers in a chain), 10BASE-T or twisted
	  pair (10 Mbps over twisted pair cable, linking computers to central
	  hubs), 10BASE-F (10 Mbps over optical fiber links, using hubs),
	  100BASE-TX (100 Mbps over two twisted pair cables, using hubs),
	  100BASE-T4 (100 Mbps over 4 standard voice-grade twisted pair
	  cables, using hubs), 100BASE-FX (100 Mbps over optical fiber links)
	  [the 100BASE varieties are also known as Fast Ethernet], and Gigabit
	  Ethernet (1 Gbps over optical fiber or short copper links).

	  If your Linux machine will be connected to an Ethernet and you have
	  an Ethernet network interface card (NIC) installed in your computer,
	  say Y here and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. You will then also have
	  to say Y to the driver for your particular NIC.

	  Note that the answer to this question won't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about Ethernet network cards. If unsure, say N.

if NET_ETHERNET

config MII
	tristate "Generic Media Independent Interface device support"
	help
	  Most ethernet controllers have MII transceiver either as an external
	  or internal device.  It is safe to say Y or M here even if your
	  ethernet card lack MII.

config MACB
	tristate "Atmel MACB support"
	depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263
	select PHYLIB
	help
	  The Atmel MACB ethernet interface is found on many AT32 and AT91
	  parts. Say Y to include support for the MACB chip.

	  To compile this driver as a module, choose M here: the module
	  will be called macb.

source "drivers/net/arm/Kconfig"

config AX88796
	tristate "ASIX AX88796 NE2000 clone support"
	depends on ARM || MIPS
	select CRC32
	select MII
	help
	  AX88796 driver, using platform bus to provide
	  chip detection and resources

config AX88796_93CX6
	bool "ASIX AX88796 external 93CX6 eeprom support"
	depends on AX88796
	select EEPROM_93CX6
	help
	  Select this if your platform comes with an external 93CX6 eeprom.

config MACE
	tristate "MACE (Power Mac ethernet) support"
	depends on PPC_PMAC && PPC32
	select CRC32
	help
	  Power Macintoshes and clones with Ethernet built-in on the
	  motherboard will usually use a MACE (Medium Access Control for
	  Ethernet) interface. Say Y to include support for the MACE chip.

	  To compile this driver as a module, choose M here: the module
	  will be called mace.

config MACE_AAUI_PORT
	bool "Use AAUI port instead of TP by default"
	depends on MACE
	help
	  Some Apple machines (notably the Apple Network Server) which use the
	  MACE ethernet chip have an Apple AUI port (small 15-pin connector),
	  instead of an 8-pin RJ45 connector for twisted-pair ethernet.  Say
	  Y here if you have such a machine.  If unsure, say N.
	  The driver will default to AAUI on ANS anyway, and if you use it as
	  a module, you can provide the port_aaui=0|1 to force the driver.

config BMAC
	tristate "BMAC (G3 ethernet) support"
	depends on PPC_PMAC && PPC32
	select CRC32
	help
	  Say Y for support of BMAC Ethernet interfaces. These are used on G3
	  computers.

	  To compile this driver as a module, choose M here: the module
	  will be called bmac.

config ARIADNE
	tristate "Ariadne support"
	depends on ZORRO
	help
	  If you have a Village Tronic Ariadne Ethernet adapter, say Y.
	  Otherwise, say N.

	  To compile this driver as a module, choose M here: the module
	  will be called ariadne.

config A2065
	tristate "A2065 support"
	depends on ZORRO
	select CRC32
	help
	  If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise,
	  say N.

	  To compile this driver as a module, choose M here: the module
	  will be called a2065.

config HYDRA
	tristate "Hydra support"
	depends on ZORRO
	select CRC32
	help
	  If you have a Hydra Ethernet adapter, say Y. Otherwise, say N.

	  To compile this driver as a module, choose M here: the module
	  will be called hydra.

config ZORRO8390
	tristate "Zorro NS8390-based Ethernet support"
	depends on ZORRO
	select CRC32
	help
	  This driver is for Zorro Ethernet cards using an NS8390-compatible
	  chipset, like the Village Tronic Ariadne II and the Individual
	  Computers X-Surf Ethernet cards. If you have such a card, say Y.
	  Otherwise, say N.

	  To compile this driver as a module, choose M here: the module
	  will be called zorro8390.

config APNE
	tristate "PCMCIA NE2000 support"
	depends on AMIGA_PCMCIA
	select CRC32
	help
	  If you have a PCMCIA NE2000 compatible adapter, say Y.  Otherwise,
	  say N.

	  To compile this driver as a module, choose M here: the module
	  will be called apne.

config APOLLO_ELPLUS
	tristate "Apollo 3c505 support"
	depends on APOLLO
	help
	  Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card.
	  If you don't have one made for Apollos, you can use one from a PC,
	  except that your Apollo won't be able to boot from it (because the
	  code in the ROM will be for a PC).

config MAC8390
	bool "Macintosh NS 8390 based ethernet cards"
	depends on MAC
	select CRC32
	help
	  If you want to include a driver to support Nubus or LC-PDS
	  Ethernet cards using an NS8390 chipset or its equivalent, say Y
	  and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

config MAC89x0
	tristate "Macintosh CS89x0 based ethernet cards"
	depends on MAC
	---help---
	  Support for CS89x0 chipset based Ethernet cards.  If you have a
	  Nubus or LC-PDS network (Ethernet) card of this type, say Y and
	  read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  This module will
	  be called mac89x0.

config MACSONIC
	tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)"
	depends on MAC
	---help---
	  Support for NatSemi SONIC based Ethernet devices.  This includes
	  the onboard Ethernet in many Quadras as well as some LC-PDS,
	  a few Nubus and all known Comm Slot Ethernet cards.  If you have
	  one of these say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  This module will
	  be called macsonic.

config MACMACE
	bool "Macintosh (AV) onboard MACE ethernet"
	depends on MAC
	select CRC32
	help
	  Support for the onboard AMD 79C940 MACE Ethernet controller used in
	  the 660AV and 840AV Macintosh.  If you have one of these Macintoshes
	  say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

config MVME147_NET
	tristate "MVME147 (Lance) Ethernet support"
	depends on MVME147
	select CRC32
	help
	  Support for the on-board Ethernet interface on the Motorola MVME147
	  single-board computer.  Say Y here to include the
	  driver for this chip in your kernel.
	  To compile this driver as a module, choose M here.

config MVME16x_NET
	tristate "MVME16x Ethernet support"
	depends on MVME16x
	help
	  This is the driver for the Ethernet interface on the Motorola
	  MVME162, 166, 167, 172 and 177 boards.  Say Y here to include the
	  driver for this chip in your kernel.
	  To compile this driver as a module, choose M here.

config BVME6000_NET
	tristate "BVME6000 Ethernet support"
	depends on BVME6000
	help
	  This is the driver for the Ethernet interface on BVME4000 and
	  BVME6000 VME boards.  Say Y here to include the driver for this chip
	  in your kernel.
	  To compile this driver as a module, choose M here.

config ATARILANCE
	tristate "Atari Lance support"
	depends on ATARI
	help
	  Say Y to include support for several Atari Ethernet adapters based
	  on the AMD Lance chipset: RieblCard (with or without battery), or
	  PAMCard VME (also the version by Rhotron, with different addresses).

config SUN3LANCE
	tristate "Sun3/Sun3x on-board LANCE support"
	depends on SUN3 || SUN3X
	help
	  Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80)
	  featured an AMD Lance 10Mbit Ethernet controller on board; say Y
	  here to compile in the Linux driver for this and enable Ethernet.
	  General Linux information on the Sun 3 and 3x series (now
	  discontinued) is at
	  <http://www.angelfire.com/ca2/tech68k/sun3.html>.

	  If you're not building a kernel for a Sun 3, say N.

config SUN3_82586
	bool "Sun3 on-board Intel 82586 support"
	depends on SUN3
	help
	  This driver enables support for the on-board Intel 82586 based
	  Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards.  Note
	  that this driver does not support 82586-based adapters on additional
	  VME boards.

config HPLANCE
	bool "HP on-board LANCE support"
	depends on DIO
	select CRC32
	help
	  If you want to use the builtin "LANCE" Ethernet controller on an
	  HP300 machine, say Y here.

config LASI_82596
	tristate "Lasi ethernet"
	depends on GSC
	help
	  Say Y here to support the builtin Intel 82596 ethernet controller
	  found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet.

config SNI_82596
	tristate "SNI RM ethernet"
	depends on NET_ETHERNET && SNI_RM
	help
	  Say Y here to support the on-board Intel 82596 ethernet controller
	  built into SNI RM machines.

config MIPS_JAZZ_SONIC
	tristate "MIPS JAZZ onboard SONIC Ethernet support"
	depends on MACH_JAZZ
	help
	  This is the driver for the onboard card of MIPS Magnum 4000,
	  Acer PICA, Olivetti M700-10 and a few other identical OEM systems.

config MIPS_AU1X00_ENET
	bool "MIPS AU1000 Ethernet support"
	depends on SOC_AU1X00
	select PHYLIB
	select CRC32
	help
	  If you have an Alchemy Semi AU1X00 based system
	  say Y.  Otherwise, say N.

config SGI_IOC3_ETH
	bool "SGI IOC3 Ethernet"
	depends on PCI && SGI_IP27
	select CRC32
	select MII
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

config MIPS_SIM_NET
	tristate "MIPS simulator Network device"
	depends on MIPS_SIM
	help
	  The MIPSNET device is a simple Ethernet network device which is
	  emulated by the MIPS Simulator.
	  If you are not using a MIPSsim or are unsure, say N.

config SGI_O2MACE_ETH
	tristate "SGI O2 MACE Fast Ethernet support"
	depends on SGI_IP32=y

config STNIC
	tristate "National DP83902AV  support"
	depends on SUPERH
	select CRC32
	help
	  Support for cards based on the National Semiconductor DP83902AV
	  ST-NIC Serial Network Interface Controller for Twisted Pair.  This
	  is a 10Mbit/sec Ethernet controller.  Product overview and specs at
	  <http://www.national.com/pf/DP/DP83902A.html>.

	  If unsure, say N.

config SUNLANCE
	tristate "Sun LANCE support"
	depends on SBUS
	select CRC32
	help
	  This driver supports the "le" interface present on all 32-bit Sparc
	  systems, on some older Ultra systems and as an Sbus option.  These
	  cards are based on the AMD Lance chipset, which is better known
	  via the NE2100 cards.

	  To compile this driver as a module, choose M here: the module
	  will be called sunlance.

config HAPPYMEAL
	tristate "Sun Happy Meal 10/100baseT support"
	depends on SBUS || PCI
	select CRC32
	help
	  This driver supports the "hme" interface present on most Ultra
	  systems and as an option on older Sbus systems. This driver supports
	  both PCI and Sbus devices. This driver also supports the "qfe" quad
	  100baseT device available in both PCI and Sbus configurations.

	  To compile this driver as a module, choose M here: the module
	  will be called sunhme.

config SUNBMAC
	tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)"
	depends on SBUS && EXPERIMENTAL
	select CRC32
	help
	  This driver supports the "be" interface available as an Sbus option.
	  This is Sun's older 100baseT Ethernet device.

	  To compile this driver as a module, choose M here: the module
	  will be called sunbmac.

config SUNQE
	tristate "Sun QuadEthernet support"
	depends on SBUS
	select CRC32
	help
	  This driver supports the "qe" 10baseT Ethernet device, available as
	  an Sbus option. Note that this is not the same as Quad FastEthernet
	  "qfe" which is supported by the Happy Meal driver instead.

	  To compile this driver as a module, choose M here: the module
	  will be called sunqe.

config SUNGEM
	tristate "Sun GEM support"
	depends on PCI
	select CRC32
	help
	  Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0.  See also
	  <http://www.sun.com/products-n-solutions/hardware/docs/pdf/806-3985-10.pdf>.

config CASSINI
	tristate "Sun Cassini support"
	depends on PCI
	select CRC32
	help
	  Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also
	  <http://www.sun.com/products-n-solutions/hardware/docs/pdf/817-4341-10.pdf>

config SUNVNET
	tristate "Sun Virtual Network support"
	depends on SUN_LDOMS
	help
	  Support for virtual network devices under Sun Logical Domains.

config NET_VENDOR_3COM
	bool "3COM cards"
	depends on ISA || EISA || MCA || PCI
	help
	  If you have a network (Ethernet) card belonging to this class, say Y
	  and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about 3COM cards. If you say Y, you will be asked for
	  your specific card in the following questions.

config EL1
	tristate "3c501 \"EtherLink\" support"
	depends on NET_VENDOR_3COM && ISA
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  Also, consider buying a
	  new card, since the 3c501 is slow, broken, and obsolete: you will
	  have problems.  Some people suggest to ping ("man ping") a nearby
	  machine every minute ("man cron") when using this card.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c501.

config EL2
	tristate "3c503 \"EtherLink II\" support"
	depends on NET_VENDOR_3COM && ISA
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c503.

config ELPLUS
	tristate "3c505 \"EtherLink Plus\" support"
	depends on NET_VENDOR_3COM && ISA && ISA_DMA_API
	---help---
	  Information about this network (Ethernet) card can be found in
	  <file:Documentation/networking/3c505.txt>.  If you have a card of
	  this type, say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c505.

config EL16
	tristate "3c507 \"EtherLink 16\" support (EXPERIMENTAL)"
	depends on NET_VENDOR_3COM && ISA && EXPERIMENTAL
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c507.

config EL3
	tristate "3c509/3c529 (MCA)/3c579 \"EtherLink III\" support"
	depends on NET_VENDOR_3COM && (ISA || EISA || MCA)
	---help---
	  If you have a network (Ethernet) card belonging to the 3Com
	  EtherLinkIII series, say Y and read the Ethernet-HOWTO, available
	  from <http://www.tldp.org/docs.html#howto>.

	  If your card is not working you may need to use the DOS
	  setup disk to disable Plug & Play mode, and to select the default
	  media type.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c509.

config 3C515
	tristate "3c515 ISA \"Fast EtherLink\""
	depends on NET_VENDOR_3COM && (ISA || EISA) && ISA_DMA_API
	help
	  If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
	  network card, say Y and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c515.

config ELMC
	tristate "3c523 \"EtherLink/MC\" support"
	depends on NET_VENDOR_3COM && MCA_LEGACY
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c523.

config ELMC_II
	tristate "3c527 \"EtherLink/MC 32\" support (EXPERIMENTAL)"
	depends on NET_VENDOR_3COM && MCA && MCA_LEGACY
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called 3c527.

config VORTEX
	tristate "3c590/3c900 series (592/595/597) \"Vortex/Boomerang\" support"
	depends on NET_VENDOR_3COM && (PCI || EISA)
	select MII
	---help---
	  This option enables driver support for a large number of 10Mbps and
	  10/100Mbps EISA, PCI and PCMCIA 3Com network cards:

	  "Vortex"    (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI
	  "Boomerang" (EtherLink XL 3c900 or 3c905)            PCI
	  "Cyclone"   (3c540/3c900/3c905/3c980/3c575/3c656)    PCI and Cardbus
	  "Tornado"   (3c905)                                  PCI
	  "Hurricane" (3c555/3cSOHO)                           PCI

	  If you have such a card, say Y and read the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>. More
	  specific information is in
	  <file:Documentation/networking/vortex.txt> and in the comments at
	  the beginning of <file:drivers/net/3c59x.c>.

	  To compile this support as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.

config TYPHOON
	tristate "3cr990 series \"Typhoon\" support"
	depends on NET_VENDOR_3COM && PCI
	select CRC32
	---help---
	  This option enables driver support for the 3cr990 series of cards:

	  3C990-TX, 3CR990-TX-95, 3CR990-TX-97, 3CR990-FX-95, 3CR990-FX-97,
	  3CR990SVR, 3CR990SVR95, 3CR990SVR97, 3CR990-FX-95 Server,
	  3CR990-FX-97 Server, 3C990B-TX-M, 3C990BSVR

	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called typhoon.

config LANCE
	tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
	depends on ISA && ISA_DMA_API
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. Some LinkSys cards are
	  of this type.

	  To compile this driver as a module, choose M here: the module
	  will be called lance.  This is recommended.

config NET_VENDOR_SMC
	bool "Western Digital/SMC cards"
	depends on ISA || MCA || EISA || MAC
	help
	  If you have a network (Ethernet) card belonging to this class, say Y
	  and read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about Western Digital cards. If you say Y, you will be
	  asked for your specific card in the following questions.

config WD80x3
	tristate "WD80*3 support"
	depends on NET_VENDOR_SMC && ISA
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called wd.

config ULTRAMCA
	tristate "SMC Ultra MCA support"
	depends on NET_VENDOR_SMC && MCA
	select CRC32
	help
	  If you have a network (Ethernet) card of this type and are running
	  an MCA based system (PS/2), say Y and read the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called smc-mca.

config ULTRA
	tristate "SMC Ultra support"
	depends on NET_VENDOR_SMC && ISA
	select CRC32
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  Important: There have been many reports that, with some motherboards
	  mixing an SMC Ultra and an Adaptec AHA154x SCSI card (or compatible,
	  such as some BusLogic models) causes corruption problems with many
	  operating systems. The Linux smc-ultra driver has a work-around for
	  this but keep it in mind if you have such a SCSI card and have
	  problems.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called smc-ultra.

config ULTRA32
	tristate "SMC Ultra32 EISA support"
	depends on NET_VENDOR_SMC && EISA
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called smc-ultra32.

config BFIN_MAC
	tristate "Blackfin 536/537 on-chip mac support"
	depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
	select CRC32
	select MII
	select PHYLIB
	select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
	help
	  This is the driver for blackfin on-chip mac device. Say Y if you want it
	  compiled into the kernel. This driver is also available as a module
	  ( = code which can be inserted in and removed from the running kernel
	  whenever you want). The module will be called bfin_mac.

config BFIN_MAC_USE_L1
	bool "Use L1 memory for rx/tx packets"
	depends on BFIN_MAC && BF537
	default y
	help
	  To get maximum network performance, you should use L1 memory as rx/tx buffers.
	  Say N here if you want to reserve L1 memory for other uses.

config BFIN_TX_DESC_NUM
	int "Number of transmit buffer packets"
	depends on BFIN_MAC
	range 6 10 if BFIN_MAC_USE_L1
	range 10 100
	default "10"
	help
	  Set the number of buffer packets used in driver.

config BFIN_RX_DESC_NUM
	int "Number of receive buffer packets"
	depends on BFIN_MAC
	range 20 100 if BFIN_MAC_USE_L1
	range 20 800
	default "20"
	help
	  Set the number of buffer packets used in driver.

config BFIN_MAC_RMII
	bool "RMII PHY Interface (EXPERIMENTAL)"
	depends on BFIN_MAC && EXPERIMENTAL
	default n
	help
	  Use Reduced PHY MII Interface

config SMC9194
	tristate "SMC 9194 support"
	depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
	select CRC32
	---help---
	  This is support for the SMC9xxx based Ethernet cards. Choose this
	  option if you have a DELL laptop with the docking station, or
	  another SMC9192/9194 based chipset.  Say Y if you want it compiled
	  into the kernel, and read the file
	  <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called smc9194.

config SMC91X
	tristate "SMC 91C9x/91C1xxx support"
	select CRC32
	select MII
	depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BFIN
	help
	  This is a driver for SMC's 91x series of Ethernet chipsets,
	  including the SMC91C94 and the SMC91C111. Say Y if you want it
	  compiled into the kernel, and read the file
	  <file:Documentation/networking/smc9.txt>  and the Ethernet-HOWTO,
	  available from  <http://www.linuxdoc.org/docs.html#howto>.

	  This driver is also available as a module ( = code which can be
	  inserted in and removed from the running kernel whenever you want).
	  The module will be called smc91x.  If you want to compile it as a
	  module, say M here and read <file:Documentation/kbuild/modules.txt>
	  as well as <file:Documentation/networking/net-modules.txt>.

config NET_NETX
	tristate "NetX Ethernet support"
	select MII
	depends on ARCH_NETX
	help
	  This is support for the Hilscher netX builtin Ethernet ports

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called netx-eth.

config DM9000
	tristate "DM9000 support"
	depends on ARM || BLACKFIN || MIPS
	select CRC32
	select MII
	---help---
	  Support for DM9000 chipset.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>.  The module will be
	  called dm9000.

config SMC911X
	tristate "SMSC LAN911[5678] support"
	select CRC32
	select MII
	depends on ARCH_PXA || SUPERH
	help
	  This is a driver for SMSC's LAN911x series of Ethernet chipsets
	  including the new LAN9115, LAN9116, LAN9117, and LAN9118.
	  Say Y if you want it compiled into the kernel, 
	  and read the Ethernet-HOWTO, available from
	  <http://www.linuxdoc.org/docs.html#howto>.

	  This driver is also available as a module. The module will be 
	  called smc911x.  If you want to compile it as a module, say M 
	  here and read <file:Documentation/kbuild/modules.txt>

config NET_VENDOR_RACAL
	bool "Racal-Interlan (Micom) NI cards"
	depends on ISA
	help
	  If you have a network (Ethernet) card belonging to this class, such
	  as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the questions about NI cards. If you say Y, you will be asked for
	  your specific card in the following questions.

config NI5010
	tristate "NI5010 support (EXPERIMENTAL)"
	depends on NET_VENDOR_RACAL && ISA && EXPERIMENTAL && BROKEN_ON_SMP
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>. Note that this is still
	  experimental code.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ni5010.

config NI52
	tristate "NI5210 support"
	depends on NET_VENDOR_RACAL && ISA
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ni52.

config NI65
	tristate "NI6510 support"
	depends on NET_VENDOR_RACAL && ISA && ISA_DMA_API
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ni65.

source "drivers/net/tulip/Kconfig"

config AT1700
	tristate "AT1700/1720 support (EXPERIMENTAL)"
	depends on (ISA || MCA_LEGACY) && EXPERIMENTAL
	select CRC32
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called at1700.

config DEPCA
	tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support"
	depends on ISA || EISA || MCA
	select CRC32
	---help---
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto> as well as
	  <file:drivers/net/depca.c>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called depca.

config HP100
	tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support"
	depends on ISA || EISA || PCI
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called hp100.

config NET_ISA
	bool "Other ISA cards"
	depends on ISA
	---help---
	  If your network (Ethernet) card hasn't been mentioned yet and its
	  bus system (that's the way the cards talks to the other components
	  of your computer) is ISA (as opposed to EISA, VLB or PCI), say Y.
	  Make sure you know the name of your card. Read the Ethernet-HOWTO,
	  available from <http://www.tldp.org/docs.html#howto>.

	  If unsure, say Y.

	  Note that the answer to this question doesn't directly affect the
	  kernel: saying N will just cause the configurator to skip all
	  the remaining ISA network card questions. If you say Y, you will be
	  asked for your specific card in the following questions.

config E2100
	tristate "Cabletron E21xx support"
	depends on NET_ISA
	select CRC32
	help
	  If you have a network (Ethernet) card of this type, say Y and read
	  the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called e2100.

config EWRK3
	tristate "EtherWORKS 3 (DE203, DE204, DE205) support"
	depends on NET_ISA
	select CRC32
	---help---
	  This driver supports the DE203, DE204 and DE205 network (Ethernet)
	  cards. If this is for you, say Y and read
	  <file:Documentation/networking/ewrk3.txt> in the kernel source as
	  well as the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called ewrk3.

config EEXPRESS
	tristate "EtherExpress 16 support"
	depends on NET_ISA
	---help---
	  If you have an EtherExpress16 network (Ethernet) card, say Y and
	  read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.  Note that the Intel
	  EtherExpress16 card used to be regarded as a very poor choice
	  because the driver was very unreliable. We now have a new driver
	  that should do better.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called eexpress.

config EEXPRESS_PRO
	tristate "EtherExpressPro support/EtherExpress 10 (i82595) support"
	depends on NET_ISA
	---help---
	  If you have a network (Ethernet) card of this type, say Y. This
	  driver supports Intel i82595{FX,TX} based boards. Note however
	  that the EtherExpress PRO/100 Ethernet card has its own separate
	  driver.  Please read the Ethernet-HOWTO, available from
	  <http://www.tldp.org/docs.html#howto>.

	  To compile this driver as a module, choose M here and read
	  <file:Documentation/networking/net-modules.txt>. The module
	  will be called eepro.

config HPLAN_PLUS
	tristate "HP PCLAN+ (27247B and 27252A) support"
	depends on NET_ISA


context:
space:
mode: