6 files changed, 8 insertions, 8 deletions

diff --git a/include/asm-m68knommu/mcfmbus.h b/include/asm-m68knommu/mcfmbus.h
index 13df9d41bd1a..319899c47a2c 100644
--- a/include/asm-m68knommu/mcfmbus.h
+++ b/include/asm-m68knommu/mcfmbus.h
@@ -37,7 +37,7 @@
 #define MCFMBUS_MFDR_MBC(a)     ((a)&0x3F)         /*M-Bus Clock*/
 
 /*
-*       Define bit flags in Controll Register
+*       Define bit flags in Control Register
 */
 
 #define MCFMBUS_MBCR_MEN           (0x80)  /* M-Bus Enable                 */
diff --git a/include/asm-parisc/dma.h b/include/asm-parisc/dma.h
index da2cf373e31c..31ad0f05af3d 100644
--- a/include/asm-parisc/dma.h
+++ b/include/asm-parisc/dma.h
@@ -17,10 +17,10 @@
 
 /*
 ** DMA_CHUNK_SIZE is used by the SCSI mid-layer to break up
-** (or rather not merge) DMA's into managable chunks.
+** (or rather not merge) DMAs into manageable chunks.
 ** On parisc, this is more of the software/tuning constraint
-** rather than the HW. I/O MMU allocation alogorithms can be
-** faster with smaller size is (to some degree).
+** rather than the HW. I/O MMU allocation algorithms can be
+** faster with smaller sizes (to some degree).
 */
 #define DMA_CHUNK_SIZE  (BITS_PER_LONG*PAGE_SIZE)
 
diff --git a/include/asm-parisc/pci.h b/include/asm-parisc/pci.h
index 7b8ad118d2fe..7b3be9ac0dda 100644
--- a/include/asm-parisc/pci.h
+++ b/include/asm-parisc/pci.h
@@ -149,7 +149,7 @@ extern int parisc_bus_is_phys; 	/* in arch/parisc/kernel/setup.c */
 /*
 ** Most PCI devices (eg Tulip, NCR720) also export the same registers
 ** to both MMIO and I/O port space.  Due to poor performance of I/O Port
-** access under HP PCI bus adapters, strongly reccomend use of MMIO
+** access under HP PCI bus adapters, strongly recommend the use of MMIO
 ** address space.
 **
 ** While I'm at it more PA programming notes:
diff --git a/include/asm-parisc/ropes.h b/include/asm-parisc/ropes.h
index 5542dd00472b..007a880615eb 100644
--- a/include/asm-parisc/ropes.h
+++ b/include/asm-parisc/ropes.h
@@ -14,7 +14,7 @@
 #endif
 
 /*
-** The number of pdir entries to "free" before issueing
+** The number of pdir entries to "free" before issuing
 ** a read to PCOM register to flush out PCOM writes.
 ** Interacts with allocation granularity (ie 4 or 8 entries
 ** allocated and free'd/purged at a time might make this
diff --git a/include/linux/ixjuser.h b/include/linux/ixjuser.h
index fd1756d3a47e..88b45895746d 100644
--- a/include/linux/ixjuser.h
+++ b/include/linux/ixjuser.h
@@ -315,7 +315,7 @@ typedef struct {
 * structures.  If the freq0 variable is non-zero, the tone table contents
 * for the tone_index are updated to the frequencies and gains defined.  It
 * should be noted that DTMF tones cannot be reassigned, so if DTMF tone
-* table indexs are used in a cadence the frequency and gain variables will
+* table indexes are used in a cadence the frequency and gain variables will
 * be ignored.
 *
 * If the array elements contain frequency parameters the driver will
diff --git a/include/linux/reiserfs_fs_sb.h b/include/linux/reiserfs_fs_sb.h
index 73e0becec086..62a7169aed8b 100644
--- a/include/linux/reiserfs_fs_sb.h
+++ b/include/linux/reiserfs_fs_sb.h
@@ -429,7 +429,7 @@ enum reiserfs_mount_options {
 /* -o hash={tea, rupasov, r5, detect} is meant for properly mounting 
 ** reiserfs disks from 3.5.19 or earlier.  99% of the time, this option
 ** is not required.  If the normal autodection code can't determine which
-** hash to use (because both hases had the same value for a file)
+** hash to use (because both hashes had the same value for a file)
 ** use this option to force a specific hash.  It won't allow you to override
 ** the existing hash on the FS, so if you have a tea hash disk, and mount
 ** with -o hash=rupasov, the mount will fail.