1 files changed, 161 insertions, 0 deletions
diff --git a/include/uapi/linux/mii.h b/include/uapi/linux/mii.h
new file mode 100644
index 000000000000..237fac4bc17b
--- /dev/null
+++ b/include/uapi/linux/mii.h
@@ -0,0 +1,161 @@
+/*
+ * linux/mii.h: definitions for MII-compatible transceivers
+ * Originally drivers/net/sunhme.h.
+ *
+ * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
+ */
+#ifndef _UAPI__LINUX_MII_H__
+#define _UAPI__LINUX_MII_H__
+#include <linux/types.h>
+#include <linux/ethtool.h>
+/* Generic MII registers. */
+#define MII_BMCR                0x00    /* Basic mode control register */
+#define MII_BMSR                0x01    /* Basic mode status register  */
+#define MII_PHYSID1             0x02    /* PHYS ID 1                   */
+#define MII_PHYSID2             0x03    /* PHYS ID 2                   */
+#define MII_ADVERTISE           0x04    /* Advertisement control reg   */
+#define MII_LPA                 0x05    /* Link partner ability reg    */
+#define MII_EXPANSION           0x06    /* Expansion register          */
+#define MII_CTRL1000            0x09    /* 1000BASE-T control          */
+#define MII_STAT1000            0x0a    /* 1000BASE-T status           */
+#define MII_MMD_CTRL            0x0d    /* MMD Access Control Register */
+#define MII_MMD_DATA            0x0e    /* MMD Access Data Register */
+#define MII_ESTATUS             0x0f    /* Extended Status             */
+#define MII_DCOUNTER            0x12    /* Disconnect counter          */
+#define MII_FCSCOUNTER          0x13    /* False carrier counter       */
+#define MII_NWAYTEST            0x14    /* N-way auto-neg test reg     */
+#define MII_RERRCOUNTER         0x15    /* Receive error counter       */
+#define MII_SREVISION           0x16    /* Silicon revision            */
+#define MII_RESV1               0x17    /* Reserved...                 */
+#define MII_LBRERROR            0x18    /* Lpback, rx, bypass error    */
+#define MII_PHYADDR             0x19    /* PHY address                 */
+#define MII_RESV2               0x1a    /* Reserved...                 */
+#define MII_TPISTATUS           0x1b    /* TPI status for 10mbps       */
+#define MII_NCONFIG             0x1c    /* Network interface config    */
+/* Basic mode control register. */
+#define BMCR_RESV               0x003f  /* Unused...                   */
+#define BMCR_SPEED1000          0x0040  /* MSB of Speed (1000)         */
+#define BMCR_CTST               0x0080  /* Collision test              */
+#define BMCR_FULLDPLX           0x0100  /* Full duplex                 */
+#define BMCR_ANRESTART          0x0200  /* Auto negotiation restart    */
+#define BMCR_ISOLATE            0x0400  /* Isolate data paths from MII */
+#define BMCR_PDOWN              0x0800  /* Enable low power state      */
+#define BMCR_ANENABLE           0x1000  /* Enable auto negotiation     */
+#define BMCR_SPEED100           0x2000  /* Select 100Mbps              */
+#define BMCR_LOOPBACK           0x4000  /* TXD loopback bits           */
+#define BMCR_RESET              0x8000  /* Reset to default state      */
+/* Basic mode status register. */
+#define BMSR_ERCAP              0x0001  /* Ext-reg capability          */
+#define BMSR_JCD                0x0002  /* Jabber detected             */
+#define BMSR_LSTATUS            0x0004  /* Link status                 */
+#define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation */
+#define BMSR_RFAULT             0x0010  /* Remote fault detected       */
+#define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
+#define BMSR_RESV               0x00c0  /* Unused...                   */
+#define BMSR_ESTATEN            0x0100  /* Extended Status in R15      */
+#define BMSR_100HALF2           0x0200  /* Can do 100BASE-T2 HDX       */
+#define BMSR_100FULL2           0x0400  /* Can do 100BASE-T2 FDX       */
+#define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
+#define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
+#define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
+#define BMSR_100FULL            0x4000  /* Can do 100mbps, full-duplex */
+#define BMSR_100BASE4           0x8000  /* Can do 100mbps, 4k packets  */
+/* Advertisement control register. */
+#define ADVERTISE_SLCT          0x001f  /* Selector bits               */
+#define ADVERTISE_CSMA          0x0001  /* Only selector supported     */
+#define ADVERTISE_10HALF        0x0020  /* Try for 10mbps half-duplex  */
+#define ADVERTISE_1000XFULL     0x0020  /* Try for 1000BASE-X full-duplex */
+#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex  */
+#define ADVERTISE_1000XHALF     0x0040  /* Try for 1000BASE-X half-duplex */
+#define ADVERTISE_100HALF       0x0080  /* Try for 100mbps half-duplex */
+#define ADVERTISE_1000XPAUSE    0x0080  /* Try for 1000BASE-X pause    */
+#define ADVERTISE_100FULL       0x0100  /* Try for 100mbps full-duplex */
+#define ADVERTISE_1000XPSE_ASYM 0x0100  /* Try for 1000BASE-X asym pause */
+#define ADVERTISE_100BASE4      0x0200  /* Try for 100mbps 4k packets  */
+#define ADVERTISE_PAUSE_CAP     0x0400  /* Try for pause               */
+#define ADVERTISE_PAUSE_ASYM    0x0800  /* Try for asymetric pause     */
+#define ADVERTISE_RESV          0x1000  /* Unused...                   */
+#define ADVERTISE_RFAULT        0x2000  /* Say we can detect faults    */
+#define ADVERTISE_LPACK         0x4000  /* Ack link partners response  */
+#define ADVERTISE_NPAGE         0x8000  /* Next page bit               */
+#define ADVERTISE_FULL          (ADVERTISE_100FULL | ADVERTISE_10FULL | \
+                                  ADVERTISE_CSMA)
+#define ADVERTISE_ALL           (ADVERTISE_10HALF | ADVERTISE_10FULL | \
+                                  ADVERTISE_100HALF | ADVERTISE_100FULL)
+/* Link partner ability register. */
+#define LPA_SLCT                0x001f  /* Same as advertise selector  */
+#define LPA_10HALF              0x0020  /* Can do 10mbps half-duplex   */
+#define LPA_1000XFULL           0x0020  /* Can do 1000BASE-X full-duplex */
+#define LPA_10FULL              0x0040  /* Can do 10mbps full-duplex   */
+#define LPA_1000XHALF           0x0040  /* Can do 1000BASE-X half-duplex */
+#define LPA_100HALF             0x0080  /* Can do 100mbps half-duplex  */
+#define LPA_1000XPAUSE          0x0080  /* Can do 1000BASE-X pause     */
+#define LPA_100FULL             0x0100  /* Can do 100mbps full-duplex  */
+#define LPA_1000XPAUSE_ASYM     0x0100  /* Can do 1000BASE-X pause asym*/
+#define LPA_100BASE4            0x0200  /* Can do 100mbps 4k packets   */
+#define LPA_PAUSE_CAP           0x0400  /* Can pause                   */
+#define LPA_PAUSE_ASYM          0x0800  /* Can pause asymetrically     */
+#define LPA_RESV                0x1000  /* Unused...                   */
+#define LPA_RFAULT              0x2000  /* Link partner faulted        */
+#define LPA_LPACK               0x4000  /* Link partner acked us       */
+#define LPA_NPAGE               0x8000  /* Next page bit               */
+#define LPA_DUPLEX              (LPA_10FULL | LPA_100FULL)
+#define LPA_100                 (LPA_100FULL | LPA_100HALF | LPA_100BASE4)
+/* Expansion register for auto-negotiation. */
+#define EXPANSION_NWAY          0x0001  /* Can do N-way auto-nego      */
+#define EXPANSION_LCWP          0x0002  /* Got new RX page code word   */
+#define EXPANSION_ENABLENPAGE   0x0004  /* This enables npage words    */
+#define EXPANSION_NPCAPABLE     0x0008  /* Link partner supports npage */
+#define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected    */
+#define EXPANSION_RESV          0xffe0  /* Unused...                   */
+#define ESTATUS_1000_TFULL      0x2000  /* Can do 1000BT Full          */
+#define ESTATUS_1000_THALF      0x1000  /* Can do 1000BT Half          */
+/* N-way test register. */
+#define NWAYTEST_RESV1          0x00ff  /* Unused...                   */
+#define NWAYTEST_LOOPBACK       0x0100  /* Enable loopback for N-way   */
+#define NWAYTEST_RESV2          0xfe00  /* Unused...                   */
+/* 1000BASE-T Control register */
+#define ADVERTISE_1000FULL      0x0200  /* Advertise 1000BASE-T full duplex */
+#define ADVERTISE_1000HALF      0x0100  /* Advertise 1000BASE-T half duplex */
+#define CTL1000_AS_MASTER       0x0800
+#define CTL1000_ENABLE_MASTER   0x1000
+/* 1000BASE-T Status register */
+#define LPA_1000LOCALRXOK       0x2000  /* Link partner local receiver status */
+#define LPA_1000REMRXOK         0x1000  /* Link partner remote receiver status */
+#define LPA_1000FULL            0x0800  /* Link partner 1000BASE-T full duplex */
+#define LPA_1000HALF            0x0400  /* Link partner 1000BASE-T half duplex */
+/* Flow control flags */
+#define FLOW_CTRL_TX            0x01
+#define FLOW_CTRL_RX            0x02
+/* MMD Access Control register fields */
+#define MII_MMD_CTRL_DEVAD_MASK 0x1f    /* Mask MMD DEVAD*/
+#define MII_MMD_CTRL_ADDR       0x0000  /* Address */
+#define MII_MMD_CTRL_NOINCR     0x4000  /* no post increment */
+#define MII_MMD_CTRL_INCR_RDWT  0x8000  /* post increment on reads & writes */
+#define MII_MMD_CTRL_INCR_ON_WT 0xC000  /* post increment on writes only */
+/* This structure is used in all SIOCxMIIxxx ioctl calls */
+struct mii_ioctl_data {
+        __u16           phy_id;
+        __u16           reg_num;
+        __u16           val_in;
+        __u16           val_out;
+};
+#endif /* _UAPI__LINUX_MII_H__ */

diff --git a/include/uapi/linux/mii.h b/include/uapi/linux/mii.h new file mode 100644 index 000000000000..237fac4bc17b --- /dev/null +++ b/include/uapi/linux/mii.h
@@ -0,0 +1,161 @@
	1	/*
	2	* linux/mii.h: definitions for MII-compatible transceivers
	3	* Originally drivers/net/sunhme.h.
	4	*
	5	* Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com)
	6	*/
	7
	8	#ifndef _UAPI__LINUX_MII_H__
	9	#define _UAPI__LINUX_MII_H__
	10
	11	#include <linux/types.h>
	12	#include <linux/ethtool.h>
	13
	14	/* Generic MII registers. */
	15	#define MII_BMCR 0x00 /* Basic mode control register */
	16	#define MII_BMSR 0x01 /* Basic mode status register */
	17	#define MII_PHYSID1 0x02 /* PHYS ID 1 */
	18	#define MII_PHYSID2 0x03 /* PHYS ID 2 */
	19	#define MII_ADVERTISE 0x04 /* Advertisement control reg */
	20	#define MII_LPA 0x05 /* Link partner ability reg */
	21	#define MII_EXPANSION 0x06 /* Expansion register */
	22	#define MII_CTRL1000 0x09 /* 1000BASE-T control */
	23	#define MII_STAT1000 0x0a /* 1000BASE-T status */
	24	#define MII_MMD_CTRL 0x0d /* MMD Access Control Register */
	25	#define MII_MMD_DATA 0x0e /* MMD Access Data Register */
	26	#define MII_ESTATUS 0x0f /* Extended Status */
	27	#define MII_DCOUNTER 0x12 /* Disconnect counter */
	28	#define MII_FCSCOUNTER 0x13 /* False carrier counter */
	29	#define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */
	30	#define MII_RERRCOUNTER 0x15 /* Receive error counter */
	31	#define MII_SREVISION 0x16 /* Silicon revision */
	32	#define MII_RESV1 0x17 /* Reserved... */
	33	#define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */
	34	#define MII_PHYADDR 0x19 /* PHY address */
	35	#define MII_RESV2 0x1a /* Reserved... */
	36	#define MII_TPISTATUS 0x1b /* TPI status for 10mbps */
	37	#define MII_NCONFIG 0x1c /* Network interface config */
	38
	39	/* Basic mode control register. */
	40	#define BMCR_RESV 0x003f /* Unused... */
	41	#define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */
	42	#define BMCR_CTST 0x0080 /* Collision test */
	43	#define BMCR_FULLDPLX 0x0100 /* Full duplex */
	44	#define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */
	45	#define BMCR_ISOLATE 0x0400 /* Isolate data paths from MII */
	46	#define BMCR_PDOWN 0x0800 /* Enable low power state */
	47	#define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */
	48	#define BMCR_SPEED100 0x2000 /* Select 100Mbps */
	49	#define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */
	50	#define BMCR_RESET 0x8000 /* Reset to default state */
	51
	52	/* Basic mode status register. */
	53	#define BMSR_ERCAP 0x0001 /* Ext-reg capability */
	54	#define BMSR_JCD 0x0002 /* Jabber detected */
	55	#define BMSR_LSTATUS 0x0004 /* Link status */
	56	#define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */
	57	#define BMSR_RFAULT 0x0010 /* Remote fault detected */
	58	#define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */
	59	#define BMSR_RESV 0x00c0 /* Unused... */
	60	#define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */
	61	#define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */
	62	#define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */
	63	#define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */
	64	#define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */
	65	#define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */
	66	#define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */
	67	#define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */
	68
	69	/* Advertisement control register. */
	70	#define ADVERTISE_SLCT 0x001f /* Selector bits */
	71	#define ADVERTISE_CSMA 0x0001 /* Only selector supported */
	72	#define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */
	73	#define ADVERTISE_1000XFULL 0x0020 /* Try for 1000BASE-X full-duplex */
	74	#define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */
	75	#define ADVERTISE_1000XHALF 0x0040 /* Try for 1000BASE-X half-duplex */
	76	#define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */
	77	#define ADVERTISE_1000XPAUSE 0x0080 /* Try for 1000BASE-X pause */
	78	#define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */
	79	#define ADVERTISE_1000XPSE_ASYM 0x0100 /* Try for 1000BASE-X asym pause */
	80	#define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */
	81	#define ADVERTISE_PAUSE_CAP 0x0400 /* Try for pause */
	82	#define ADVERTISE_PAUSE_ASYM 0x0800 /* Try for asymetric pause */
	83	#define ADVERTISE_RESV 0x1000 /* Unused... */
	84	#define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */
	85	#define ADVERTISE_LPACK 0x4000 /* Ack link partners response */
	86	#define ADVERTISE_NPAGE 0x8000 /* Next page bit */
	87
	88	#define ADVERTISE_FULL (ADVERTISE_100FULL \| ADVERTISE_10FULL \| \
	89	ADVERTISE_CSMA)
	90	#define ADVERTISE_ALL (ADVERTISE_10HALF \| ADVERTISE_10FULL \| \
	91	ADVERTISE_100HALF \| ADVERTISE_100FULL)
	92
	93	/* Link partner ability register. */
	94	#define LPA_SLCT 0x001f /* Same as advertise selector */
	95	#define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */
	96	#define LPA_1000XFULL 0x0020 /* Can do 1000BASE-X full-duplex */
	97	#define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */
	98	#define LPA_1000XHALF 0x0040 /* Can do 1000BASE-X half-duplex */
	99	#define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */
	100	#define LPA_1000XPAUSE 0x0080 /* Can do 1000BASE-X pause */
	101	#define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */
	102	#define LPA_1000XPAUSE_ASYM 0x0100 /* Can do 1000BASE-X pause asym*/
	103	#define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */
	104	#define LPA_PAUSE_CAP 0x0400 /* Can pause */
	105	#define LPA_PAUSE_ASYM 0x0800 /* Can pause asymetrically */
	106	#define LPA_RESV 0x1000 /* Unused... */
	107	#define LPA_RFAULT 0x2000 /* Link partner faulted */
	108	#define LPA_LPACK 0x4000 /* Link partner acked us */
	109	#define LPA_NPAGE 0x8000 /* Next page bit */
	110
	111	#define LPA_DUPLEX (LPA_10FULL \| LPA_100FULL)
	112	#define LPA_100 (LPA_100FULL \| LPA_100HALF \| LPA_100BASE4)
	113
	114	/* Expansion register for auto-negotiation. */
	115	#define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */
	116	#define EXPANSION_LCWP 0x0002 /* Got new RX page code word */
	117	#define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */
	118	#define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */
	119	#define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */
	120	#define EXPANSION_RESV 0xffe0 /* Unused... */
	121
	122	#define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */
	123	#define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */
	124
	125	/* N-way test register. */
	126	#define NWAYTEST_RESV1 0x00ff /* Unused... */
	127	#define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */
	128	#define NWAYTEST_RESV2 0xfe00 /* Unused... */
	129
	130	/* 1000BASE-T Control register */
	131	#define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */
	132	#define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */
	133	#define CTL1000_AS_MASTER 0x0800
	134	#define CTL1000_ENABLE_MASTER 0x1000
	135
	136	/* 1000BASE-T Status register */
	137	#define LPA_1000LOCALRXOK 0x2000 /* Link partner local receiver status */
	138	#define LPA_1000REMRXOK 0x1000 /* Link partner remote receiver status */
	139	#define LPA_1000FULL 0x0800 /* Link partner 1000BASE-T full duplex */
	140	#define LPA_1000HALF 0x0400 /* Link partner 1000BASE-T half duplex */
	141
	142	/* Flow control flags */
	143	#define FLOW_CTRL_TX 0x01
	144	#define FLOW_CTRL_RX 0x02
	145
	146	/* MMD Access Control register fields */
	147	#define MII_MMD_CTRL_DEVAD_MASK 0x1f /* Mask MMD DEVAD*/
	148	#define MII_MMD_CTRL_ADDR 0x0000 /* Address */
	149	#define MII_MMD_CTRL_NOINCR 0x4000 /* no post increment */
	150	#define MII_MMD_CTRL_INCR_RDWT 0x8000 /* post increment on reads & writes */
	151	#define MII_MMD_CTRL_INCR_ON_WT 0xC000 /* post increment on writes only */
	152
	153	/* This structure is used in all SIOCxMIIxxx ioctl calls */
	154	struct mii_ioctl_data {
	155	__u16 phy_id;
	156	__u16 reg_num;
	157	__u16 val_in;
	158	__u16 val_out;
	159	};
	160
	161	#endif /* _UAPI__LINUX_MII_H__ */